240 MHz SAW Filter 6.7 MHz Bandwidth Part Number: SF0240BA03145S DESCRIPTION * * * 240 MHz SAW bandpass filter with 6.7 MHz bandwidth. 13.3 x 6.5 mm SMP. RoHS compliant. TYPICAL PERFORMANCE Horizontal: Vertical from Top: S11 (220-260 MHz) Frequency : Relative Magnitude : Relative Magnitude : Phase Linearity : Group Delay Deviation : 4 10 1 10 100 MHz/div dB/div dB/div deg/div ns/div S22 (220-260 MHz) Spectrum Microwave 400 Nickerson Road, Marlborough, MA 01752, USA * Phone 1-508-251-6400 * Fax 1-508-251-6401 www.SpectrumMicrowave.com DSSF0240BA03145S Rev A ECN 36650 19-Mar-2010 Page 1 of 3 240 MHz SAW Filter 6.7 MHz Bandwidth Part Number: SF0240BA03145S SPECIFICATION Parameter Center Frequency, FC 1 Insertion Loss at Fc 1 dB Bandwidth 2 20 dB Bandwidth 2 40 dB Bandwidth 2 50 dB Bandwidth 2 Amplitude Ripple (Fc +/- 3.3 MHz) Group Delay Variation (Fc +/- 3.3 MHz) 3 Device Delay Phase Linearity (Fc +/- 3.3 MHz) Input / Output Return Loss at Fc Rejection (120 to 225 MHz) 2 Rejection (255 to 360 MHz) 2 Temperature Coefficient of Frequency Source/Load Impedance Ambient Temperature Notes: Min 6.7 50 50 Typ 240 17.9 7.06 8.67 9.25 14.07 0.7 80 1.27 4 10 55 55 -18 50 25 Max 20 8.8 14 30 1 100 8 - Units MHz dB MHz MHz MHz MHz dB p-p ns us deg p-p dB dB dB ppm/C ohms C 1. Defined as the average of the lower and upper 3 dB frequencies at room ambient. 2. All dB levels are defined relative to the insertion loss. 3. A smoothing aperture of 0.25% of span may be used for this measurement. MAXIMUM RATINGS Parameter Storage Temperature Range Operating Temperature Range Input Power Level Min Max -40 -10 0 85 85 13 Units C C dBm MATCHING CIRCUIT 11 Input 50 Single-ended All other pads GND Typical Component values: 5 Ls1 = 10 nH Cp1 = 39 pF Output 50 Single-ended GND Ls2 = 12 nH Cp2 = 39 pF Notes: * Recommend 2% or better tolerance matching components. Typical inductor Q=45. * Optimum values may change depending on board layout. Values shown are intended as a guide only. Spectrum Microwave 400 Nickerson Road, Marlborough, MA 01752, USA * Phone 1-508-251-6400 * Fax 1-508-251-6401 www.SpectrumMicrowave.com DSSF0240BA03145S Rev A ECN 36650 19-Mar-2010 Page 2 of 3 240 MHz SAW Filter 6.7 MHz Bandwidth Part Number: SF0240BA03145S PACKAGE OUTLINE SUGGESTED FOOTPRINT Units: mm Tolerances are 0.15 mm except where indicated. Pad Configuration: Input: 11 Output: 5 Ground: All other pads Package Material: Body: Al2O3 ceramic Lid: Kovar, Ni plated Terminations: Au plating 1 m min, over a 1.3-8.9 m Ni plating ISO 9001 Registered All specifications are believed to be accurate and reliable. However, Spectrum Microwave reserves the right to make changes without notice. (c) 2010 All rights reserved. Spectrum Microwave 400 Nickerson Road, Marlborough, MA 01752, USA * Phone 1-508-251-6400 * Fax 1-508-251-6401 www.SpectrumMicrowave.com DSSF0240BA03145S Rev A ECN 36650 19-Mar-2010 Page 3 of 3