TSOP41..ST1F Vishay Semiconductors IR Receiver Modules for Remote Control Systems Description The TSOP41..ST1F - series are miniaturized receivers for infrared remote control systems. PIN diode and preamplifier are assembled on lead frame, the epoxy package is designed as IR filter. The demodulated output signal can directly be decoded by a microprocessor. The main benefit is the reliable function even in disturbed ambient and the protection against uncontrolled output pulses. 1 2 3 18296 Features Special Features * Photo detector and preamplifier in one package * Internal filter for PCM frequency e3 * Improved shielding against electrical field disturbance * TTL and CMOS compatibility * Output active low * Low power consumption * High immunity against ambient light * Lead (Pb)-free component * Component in accordance to RoHS 2002/95/EC and WEEE 2002/96/EC * Enhanced data rate of 4000 bit/s * Suitable burst length 6 cycles/burst * Enhanced suppression of disturbance signals by special filtering Block Diagram Parts Table Part Carrier Frequency TSOP4130ST1F 30 kHz TSOP4133ST1F 33 kHz TSOP4136ST1F 36 kHz TSOP4137ST1F 36.7 kHz TSOP4138ST1F 38 kHz TSOP4140ST1F 40 kHz TSOP4156ST1F 56 kHz Application Circuit 16842 3 25 k VS 1 Input AGC Band Pass Demodulator OUT Transmitter TSOPxxxx with TSALxxxx Circuit 16834_1 R1 = 100 VS OUT GND + VS C1 = 4.7 F C VO GND 2 PIN Control Circuit GND R1 and C1 recommended to suppress power supply disturbances. The output voltage should not be hold continuously a a voltage below VO = 3.3 V by the external circuit. Document Number 81298 Rev. 1.0, 06-Mar-06 www.vishay.com 1 TSOP41..ST1F Vishay Semiconductors Absolute Maximum Ratings Tamb = 25 C, unless otherwise specified Symbol Value Supply Voltage Parameter (Pin 3) Test condition VS - 0.3 to + 6.0 V Supply Current (Pin 3) IS 5 mA Output Voltage (Pin 1) VO - 0.3 to + 6.0 V Output Current (Pin 1) IO 5 mA Tj 100 C Tstg - 25 to + 85 C Junction Temperature Storage Temperature Range Operating Temperature Range Unit Tamb - 25 to + 85 C Power Consumption (Tamb 85 C) Ptot 50 mW Soldering Temperature t 10 s, 1 mm from case Tsd 260 C Electrical and Optical Characteristics Tamb = 25 C, unless otherwise specified Parameter Supply Current (Pin 3) Symbol Min Typ. Max VS = 5 V, Ev = 0 Test condition ISD 0.8 1.1 1.5 VS = 5 V, Ev = 40 klx, sunlight ISH Supply Voltage (Pin 3) VS Transmission Distance Ev = 0, test signal see fig.3, IR diode TSAL6200, IF = 250 mA Output Voltage Low (Pin 1) IOL = 0.5 mA,Ee = 0.7 mW/m2, f = fo, test signal see fig. 1 Minimum Irradiance (30 - 40 kHz) Pulse width tolerance: tpi - 5/fo < tpo < tpi + 6/fo, test signal see fig.3 Ee min Minimum Irradiance (56 kHz) Pulse width tolerance: tpi - 5/fo < tpo < tpi + 6/fo, test signal see fig.3 Ee min Maximum Irradiance Test signal see fig. 1 Ee max Directivity Angle of half transmission distance www.vishay.com 2 1.4 4.5 d mA mA 5.5 35 V m 250 mV 0.2 0.4 mW/m2 0.3 0.5 mW/m2 VOL 1/2 Unit 30 W/m2 45 deg Document Number 81298 Rev. 1.0, 06-Mar-06 TSOP41..ST1F Vishay Semiconductors Typical Characteristics Tamb = 25 C, unless otherwise specified 1.0 Optical Test Signal (IR diode TSAL6200, IF = 0.4 A, N = 6 pulses, f = f0, T = 10 ms) t tpi *) T *) tpi 6/fo is recommended for optimal function Output Signal VO 1) 2) VOH VOL 14337 3/f0 < td < 9/f0 tpi - 4/f 0 < tpo < tpi + 6/f0 td1 ) Ton ,Toff - Output Pulse Width (ms) Ee 0.9 0.8 0.6 0.5 Toff 0.4 0.3 0.2 = 950 nm, optical test signal, fig. 3 0.1 0.0 0.1 t tpo2 ) Ton 0.7 1.0 16910 Figure 1. Output Function Figure 4. Output Pulse Diagram E e min / E e - Rel. Responsivity 1.2 0.30 Output Pulse 0.25 0.20 0.15 Input Burst Duration 0.10 = 950 nm, optical test signal, fig.1 0.05 0.00 0.1 1.0 10.0 Ee - Irradiance (mW/m) 16907 Optical Test Signal t 600 s T = 60 ms VO 94 8134 Output Signal, (see Fig. 4) VOH VOL Ton Toff 0.8 0.6 0.4 Document Number 81298 Rev. 1.0, 06-Mar-06 0.9 1.1 f/f0 - Relative Frequency t 1.3 Figure 5. Frequency Dependence of Responsivity 4.0 3.5 3.0 Correlation with ambient light sources: 10 W/m2 1.4 klx (Std.illum.A, T= 2855 K) 10 W/m2 8.2 klx (Daylight, T = 5900 K) 2.5 2.0 1.5 Ambient, = 950 nm 1.0 0.5 0.0 0.01 16911 Figure 3. Output Function f = f0 5 % f (3 dB) = f0/7 0.2 16926 Figure 2. Pulse Length and Sensitivity in Dark Ambient 600 s 1.0 0.0 0.7 100.0 1000.0 10000.0 Ee min- Threshold Irradiance (mW/m2 ) t po - Output Pulse Width (ms) 0.35 Ee 10.0 100.0 1000.010000.0 Ee - Irradiance (mW/m2) 0.10 1.00 10.00 100.00 E - Ambient DC Irradiance (W/m2) Figure 6. Sensitivity in Bright Ambient www.vishay.com 3 TSOP41..ST1F Vishay Semiconductors 0.6 f = fo 1.5 f = 10 kHz 1.0 f = 1 kHz 0.5 f = 100 Hz 0.0 0.1 1.0 10.0 100.0 1000.0 VsRMS - AC Voltage on DC Supply Voltage (mV) 16912 2.0 f(E) = f0 1.6 1.2 0.8 0.4 0.0 0.0 0.4 0.8 1.2 1.6 Figure 8. Sensitivity vs. Electric Field Disturbances Sensitivity in dark ambient 0.4 0.3 0.2 0.1 90 Figure 10. Sensitivity vs. Ambient Temperature 1.0 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 750 2.0 E - Field Strength of Disturbance (kV/m) 94 8147 0.5 0.0 - 30 - 15 0 15 30 45 60 75 16918 Tamb - Ambient Temperature (C) S ( ) rel - Relative Spectral Sensitivity E e min- Threshold Irradiance (mW/m) Figure 7. Sensitivity vs. Supply Voltage Disturbances Ee min- Threshold Irradiance (mW/m) Ee min- Threshold Irradiance (mW/m) 2.0 850 950 1050 1150 - Wavelength (nm) 18998 Figure 11. Relative Spectral Sensitivity vs. Wavelength 0 1.0 10 20 30 Max. Envelope Duty Cycle 0.9 0.8 0.7 40 1.0 0.6 0.5 0.9 50 0.8 60 0.4 0.3 f = 38 kHz, Ee = 2 mW/m2 0.2 70 0.7 0.1 80 0.0 0 16914 20 40 60 80 100 120 Burst Length (number of cycles/burst) Figure 9. Max. Envelope Duty Cycle vs. Burstlength www.vishay.com 4 0.6 96 12223p2 0.4 0.2 0 0.2 0.4 0.6 drel - Relative Transmission Distance Figure 12. Directivity Document Number 81298 Rev. 1.0, 06-Mar-06 TSOP41..ST1F Vishay Semiconductors The circuit of the TSOP41..ST1F is designed in that way that unexpected output pulses due to noise or disturbance signals are avoided. A bandpass filter, an integrator stage and an automatic gain control are used to suppress such disturbances. The distinguishing mark between data signal and disturbance signal are carrier frequency, burst length and duty cycle. The data signal should fulfill the following conditions: * Carrier frequency should be close to center frequency of the bandpass (e.g. 38 kHz). * Burst length should be 6 cycles/burst or longer. * After each burst which is between 6 cycles and 70 cycles a gap time of at least 10 cycles is necessary. * For each burst which is longer than 1.8 ms a corresponding gap time is necessary at some time in the data stream. This gap time should have at least same length as the burst. * Up to 2200 short bursts per second can be received continuously. Some examples for suitable data format are: NEC Code, Toshiba Micom Format, Sharp Code, RC5 Code, RC6 Code, RCMM Code, R-2000 Code, RECS-80 Code. When a disturbance signal is applied to the TSOP41..ST1F it can still receive the data signal. However the sensitivity is reduced to that level that no unexpected pulses will occur. Some examples for such disturbance signals which are suppressed by the TSOP41..ST1F are: * DC light (e.g. from tungsten bulb or sunlight) * Continuous signal at 38 kHz or at any other frequency * Signals from fluorescent lamps with electronic ballast (an example of the signal modulation is in the figure below). Document Number 81298 Rev. 1.0, 06-Mar-06 IR Signal Suitable Data Format IR Signal from fluorescent lamp with low modulation 0 16920 5 10 Time (ms) 15 20 Figure 13. IR Signal from Fluorescent Lamp with low Modulation www.vishay.com 5 TSOP41..ST1F Vishay Semiconductors Package Dimensions in mm 16793 www.vishay.com 6 Document Number 81298 Rev. 1.0, 06-Mar-06 TSOP41..ST1F Vishay Semiconductors Ozone Depleting Substances Policy Statement It is the policy of Vishay Semiconductor GmbH to 1. Meet all present and future national and international statutory requirements. 2. Regularly and continuously improve the performance of our products, processes, distribution and operating systems with respect to their impact on the health and safety of our employees and the public, as well as their impact on the environment. It is particular concern to control or eliminate releases of those substances into the atmosphere which are known as ozone depleting substances (ODSs). The Montreal Protocol (1987) and its London Amendments (1990) intend to severely restrict the use of ODSs and forbid their use within the next ten years. Various national and international initiatives are pressing for an earlier ban on these substances. Vishay Semiconductor GmbH has been able to use its policy of continuous improvements to eliminate the use of ODSs listed in the following documents. 1. Annex A, B and list of transitional substances of the Montreal Protocol and the London Amendments respectively 2. Class I and II ozone depleting substances in the Clean Air Act Amendments of 1990 by the Environmental Protection Agency (EPA) in the USA 3. Council Decision 88/540/EEC and 91/690/EEC Annex A, B and C (transitional substances) respectively. Vishay Semiconductor GmbH can certify that our semiconductors are not manufactured with ozone depleting substances and do not contain such substances. We reserve the right to make changes to improve technical design and may do so without further notice. Parameters can vary in different applications. All operating parameters must be validated for each customer application by the customer. Should the buyer use Vishay Semiconductors products for any unintended or unauthorized application, the buyer shall indemnify Vishay Semiconductors against all claims, costs, damages, and expenses, arising out of, directly or indirectly, any claim of personal damage, injury or death associated with such unintended or unauthorized use. Vishay Semiconductor GmbH, P.O.B. 3535, D-74025 Heilbronn, Germany Document Number 81298 Rev. 1.0, 06-Mar-06 www.vishay.com 7 Legal Disclaimer Notice Vishay Notice Specifications of the products displayed herein are subject to change without notice. Vishay Intertechnology, Inc., or anyone on its behalf, assumes no responsibility or liability for any errors or inaccuracies. Information contained herein is intended to provide a product description only. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document. Except as provided in Vishay's terms and conditions of sale for such products, Vishay assumes no liability whatsoever, and disclaims any express or implied warranty, relating to sale and/or use of Vishay products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright, or other intellectual property right. The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications. Customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Vishay for any damages resulting from such improper use or sale. Document Number: 91000 Revision: 08-Apr-05 www.vishay.com 1