STA328 2.1-channel high-efficiency digital audio system Features ! Wide supply voltage range (10 V - 36 V) ! Three power output configurations - 2 x 40 W + 1 x 80 W - 2 x 80 W - 1 x 160 W PowerSO-36 with slug up ) s ( ct ! PowerSO-36 package ! 2.1 channels of 24-bit DDX(R) ! 100-dB SNR and dynamic range ! 32 kHz to 192 kHz input sample rates ! Digital gain/attenuation +48 dB to -80 dB in 0.5-dB steps ! Four 28-bit user programmable biquads (EQ) per channel ! I2C control ! 2-channel I2S input data interface ! Individual channel and master gain/attenuation ! Individual channel and master soft/hard mute ! Individual channel volume and EQ bypass ! Bass/treble tone control ! Dual independent programmable limiters/compressors ) (s t c u d o r P e t e l o s b O ! AutoModes - 32 preset EQ curves - 15 preset crossover settings - Auto volume controlled loudness - 3 preset volume curves - 2 preset anti-clipping modes - Preset night-time listening mode - Preset TV AGC Table 1. u d o r P e ! Input and output channel mapping ! AM noise-reduction and PWM frequency-shifting modes ! Software volume update and muting t e l o s b O ! Auto zero detect and invalid input detect muting ! Selectable DDX(R) ternary or binary PWM output + variable PWM speeds ! Selectable de-emphasis ! Post-EQ user programmable mix with default 2.1 bass-management settings ! Variable max power correction for lower fullpower THD ! Four output routing configurations ! Selectable clock input ratio ! 96 kHz internal processing sample rate, 24 to 28-bit precision ! Video application supports 576 * fs input mode. Device summary Order code Package Packaging STA328 PowerSO-36 Tube STA32813TR PowerSO-36 Tape and reel May 2008 Rev 4 1/57 www.st.com 1 Contents STA328 Contents 1 2 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 1.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 1.2 EQ processing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 1.3 Output configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 1.4 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 ) s ( ct 3 Pin out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 2.1 Package pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 2.2 Pin list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 2.3 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 u d o r P e t e l o Electrical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 3.1 General interface specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 3.2 DC electrical specifications (3.3 V buffers) . . . . . . . . . . . . . . . . . . . . . . . . 12 3.3 Power electrical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 ) (s s b O 4 Electrical characteristics curves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 5 I2C bus specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 t c u d o r 5.1 Communication protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 5.2 Device addressing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 5.3 Write operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 5.4 Read operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 P e t e l o s b O 6 2/57 Register description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 6.1 Configuration register A (addr 0x00) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 6.2 Configuration register B (addr 0x01) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 6.3 Configuration register C (addr 0x02) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 6.3.1 DDX(R) power output mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 6.3.2 DDX(R) variable compensating pulse size . . . . . . . . . . . . . . . . . . . . . . . . 26 6.4 Configuration register D (addr 0x03) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 6.5 Configuration register E (addr 0x04) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 STA328 Contents 6.6 Configuration register F (addr 0x05) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 6.7 Volume control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 6.8 6.9 6.7.1 Master controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 6.7.2 Channel controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 6.7.3 Volume description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 AutoMode registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 6.8.1 AutoModes EQ, volume, GC (addr 0x0B) . . . . . . . . . . . . . . . . . . . . . . . 35 6.8.2 AutoMode AM/pre-scale/bass management scale (addr 0x0C) . . . . . . 36 6.8.3 Preset EQ settings (addr 0x0D) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 ) s ( ct Channel configuration registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 6.9.1 Channel 1 configuration (addr 0x0E) . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 6.9.2 Channel 2 configuration (addr 0x0F) . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 6.9.3 Channel 3 configuration (addr 0x10) . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 u d o r P e 6.10 Tone control (addr 0x11) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 6.11 Dynamics control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 t e l o 6.11.1 Limiter 1 attack/release threshold (addr 0x12) . . . . . . . . . . . . . . . . . . . . 41 6.11.2 Limiter 1 attack/release threshold (addr 0x13) . . . . . . . . . . . . . . . . . . . . 41 6.11.3 Limiter 2 attack/release rate (addr 0x14) . . . . . . . . . . . . . . . . . . . . . . . . 41 6.11.4 Limiter 2 attack/release threshold (addr 0x15) . . . . . . . . . . . . . . . . . . . . 41 6.11.5 Dynamics control description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 6.11.6 Anti-clipping mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 ) (s s b O t c u od 6.11.7 7 r P e User programmable processing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 t e l o s b O Dynamic range compression mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 7.1 EQ - biquad equation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 7.2 Pre-scale . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 7.3 Post-scale . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 7.4 Mix/bass management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 7.5 Calculating 24-bit signed fractional numbers from a dB value . . . . . . . . . 47 7.6 User defined coefficient RAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 7.6.1 Coefficient address register 1 (addr 0x16) . . . . . . . . . . . . . . . . . . . . . . . 47 7.6.2 Coefficient b1data register bits 23:16 (addr 0x17) . . . . . . . . . . . . . . . . . 47 7.6.3 Coefficient b1data register bits 15:8 (addr 0x18) . . . . . . . . . . . . . . . . . . 47 7.6.4 Coefficient b1data register bits 7:0 (addr 0x19) . . . . . . . . . . . . . . . . . . . 47 7.6.5 Coefficient b2 data register bits 23:16 (addr 0x1A) . . . . . . . . . . . . . . . . 47 7.6.6 Coefficient b2 data register bits 15:8 (addr 0x1B) . . . . . . . . . . . . . . . . . 48 3/57 Contents STA328 7.6.7 Coefficient b2 data register bits 7:0 (addr 0x1C) . . . . . . . . . . . . . . . . . . 48 7.6.8 Coefficient a1 data register bits 23:16 (addr 0x1D) . . . . . . . . . . . . . . . . 48 7.6.9 Coefficient a1 data register bits 15:8 (addr 0x1E) . . . . . . . . . . . . . . . . . 48 7.6.10 Coefficient a1 data register bits 7:0 (addr 0x1F) . . . . . . . . . . . . . . . . . . 48 7.6.11 Coefficient a2 data register bits 23:16 (addr 0x20) . . . . . . . . . . . . . . . . 48 7.6.12 Coefficient a2 data register bits 15:8 (addr 0x21) . . . . . . . . . . . . . . . . . 48 7.6.13 Coefficient a2 data register bits 7:0 (addr 0x22) . . . . . . . . . . . . . . . . . . 48 7.6.14 Coefficient b0 data register bits 23:16 (addr 0x23) . . . . . . . . . . . . . . . . 49 7.6.15 Coefficient b0 data register bits 15:8 (addr 0x24) . . . . . . . . . . . . . . . . . 49 7.6.16 Coefficient b0 data register bits 7:0 (addr 0x25) . . . . . . . . . . . . . . . . . . 49 7.6.17 Coefficient write control register (addr 0x26) . . . . . . . . . . . . . . . . . . . . . 49 ) s ( ct u d o 7.7 Reading a coefficient from RAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 7.8 Reading a set of coefficients from RAM . . . . . . . . . . . . . . . . . . . . . . . . . . 50 7.9 Writing a single coefficient to RAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 7.10 Writing a set of coefficients to RAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 7.11 Variable max power correction (addr 0x27, 0x28) . . . . . . . . . . . . . . . . . . 53 7.12 Fault detect recovery (addr 0x2B, 0x2C) . . . . . . . . . . . . . . . . . . . . . . . . . 53 r P e t e l o ) (s s b O 8 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 9 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 t c u d o r P e t e l o s b O 4/57 STA328 Description 1 Description 1.1 Overview The STA328 comprises digital audio processing, digital amplifier control and DDX(R) power output stage to create a high-power single-chip DDX(R) solution for high-quality, high-efficiency, all digital amplification. The STA328 power section consists of four independent half-bridges. These can be configured via digital control to operate in different modes. 2.1 channels can be provided by two half-bridges and a single full-bridge to give up to 2 x 40 W plus 1 x 80 W of power output. Two channels can be provided by two full-bridges to give up to 2 x 80 W of power. The IC can also be configured as a single parallel full-bridge capable of high-current operation and 1 x 160 W output. ) s ( ct Also provided in the STA328 is a full assortment of digital processing features. This includes up to four programmable 28-bit biquads (EQ) per channel and bass/treble tone control. AutoModes enable a time-to-market advantage by substantially reducing the amount of software development needed for certain functions. This includes auto volume loudness, preset volume curves, preset EQ settings. New advanced AM radio-interference reduction modes. u d o r P e t e l o The serial audio data input interface accepts all possible formats, including the popular I2S format. s b O Three channels of DDX(R) processing are provided. This high-quality conversion from PCM audio to patented DDX(R) 3-state PWM switching provides over 100 dB of SNR and dynamic range. ) (s Figure 1. t c u Block diagram SDA od let so b O r P e LRCKI BICKI SDI_12 SCL DDX-SPIRIT I 2C l System Contro Serial Data Input, Channel Mapping & Resampling OUT1A Audio EQ, Mix, Crossver, Volume, Limiter Processing (R) DDX Processing Quad Half-Bridge Power Stage OUT1B OUT2A OUT2B EAPD System Timing PLL TWARN FAULT Power-Down CLK Figure 2. I2 S Input Channel signal flow diagram through the digital core Channel Mapping Re-sampling EQ Processing M ix Crossover Filter Volume Limiter 4X Interp DDX(R) DDX Output 5/57 Description 1.2 STA328 EQ processing Two channels of input data (re-sampled if necessary) at 96 kHz are provided to the EQ processing block. In this block, up to four user-defined biquads can be applied to each of the two channels. Pre-scaling, DC-blocking, high-pass, de-emphasis, bass, and tone control filters can also be applied based on various configuration parameter settings. The entire EQ block can be bypassed for all channels simultaneously by setting the DSPB bit to 1. And the CxEQBP bits can be used to bypass the EQ function on a per channel basis. Figure 3 shows the internal signal flow through the EQ block. Figure 3. Channel signal flow through the EQ block Re-sampled Input Pre Scale High-P ass Filter BQ#1 BQ#2 BQ#3 4 Biquads User defined if AMEQ = 00 Preset EQ if AMEQ = 01 Auto Loudness if AMEQ = 10 If HPB = 0 If DSPB = 0 & CxEQB = 0 1.3 Output configurations Figure 4. ) s ( ct T reble Filter r P e u d o To Mix If CxT CB = 0 BT C: Bass Boost/Cut T T C: T reble Boost/Cut t e l o s b O OUT1A t c u Half Bridge od s b O ) (s If DEMP = 1 Bass Filter Output power-stage configurations Half Bridge e t e ol DeEmphasis BQ#4 Pr Half Bridge Half Bridge Half Bridge Half Bridge Half Bridge Channel 1 2-channel (full-bridge) configuration, register bits OCFG[1:0] = 00 OUT1B OUT2A Channel 2 OUT2B Channel 1 OUT1A 2.1-channel configuration, register bits OCFG[1:0] = 01 Channel 2 OUT1B OUT2A Channel 3 Half Bridge OUT2B OUT1A Half Bridge Half Bridge 1-channel mono-parallel configuration, register bits OCFG[1:0] = 11 OUT1B Channel 3 Half Bridge Half Bridge 6/57 OUT2A OUT2B The setup register is Configuration register F (addr 0x05) on page 31 STA328 1.4 Description Applications Figure 5. Application circuit for 2.1/2.0 configurable solution ) s ( ct u d o SUB_GND r P e t e l o ) (s s b O t c u d o r P e t e l o s b O 7/57 Pin out STA328 2 Pin out 2.1 Package pins Figure 6. Pin connections VCC_SIGN VSS VDD GND BICKI LRCKI SDI VDDA GNDA XTI PLL_FILTER RESERVED SDA SCL RESET CONFIG VL VDD_REG 2.2 Pin list Table 2. P e 1 8/57 Name Description Ground N.C. N.C. Not connected O OUT2B Output half bridge 2B 4 I/O VCC2B Positive supply 5 N.C. N.C. Not connected 6 I/O GND2B Negative supply 7 I/O GND2A Negative supply 8 I/O VCC2A Positive supply 9 O OUT2A Output half bridge 2A 10 O OUT1B Output half bridge 1B 11 I/O VCC1B Positive supply 12 I/O GND1B Negative supply 13 I/O. GND1A Negative supply 14 N.C. N.C. Not connected 3 ) s ( ct u d o r P e t e l o s b O SUB_GND N.C. OUT2B VCC2B N.C. GND2B GND2A VCC2A OUT2A OUT1B VCC1B GND1B GND1A N.C. VCC1A OUT1A GND_CLEAN GND_REG SUB_GND let O Type 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 I/O 2 o s b ) (s t c u Pin list d o r Number 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 STA328 Pin out Table 2. Pin list Number Type Description 15 I/O VCC1A Positive supply 16 O OUT1A Output half bridge 1A 17 I/O GND_CLEAN Logical ground 18 I/O GND_REG Substrate ground 19 I/O VDD_REG Logic supply 20 I/O VL Logic supply 21 I CONFIG Logic levels 22 I RESET Reset 23 I SCL I2C serial clock 24 I/O SDA I2C serial data 25 - RESERVED This pin must be connected to GND 26 I PLL_FILTER Connection to PLL filter 27 I XTI PLL input clock 28 I/O GNDA Analog ground 29 I/O VDDA 30 I SDI 31 I/O LRCKI 32 I 33 I/O 34 I/O P e 36 (s) BICKI ct r P e t e l o bs Analog supply, nominally 3.3 V -O I2S serial data channels 1 & 2 I2S left/right clock, I2S serial clock Digital ground VDD Digital supply, nominally 3.3 V I/O VSS 5 V regulator referred to +VCC I/O VCC_SIGN 5 V regulator referred to ground du ) s ( ct u d o GND ro 35 t e l o s b O 2.3 Name Pin description OUT1A, 1B, 2A and 2B (pins 16, 10, 9 and 3) Output half bridge PWM outputs 1A, 1B, 2A and 2B provide the input signals to the speakers. RESET (pin 22) Driving RESET low sets all outputs low and returns all register settings to their default (reset) values. The reset is asynchronous to the internal clock. 9/57 Pin out STA328 I2C signals (pins 23 and 24) The SDA (I2C Data) and SCL (I2C Clock) pins operate according to the I2C specification (Chapter 5 on page 16 gives more information). Fast-mode (400 kB/s) I2C communication is supported. GNDA and VDDA (pins 28 and 29) This is the 3.3 V analog supply for the phase locked loop. It must be well decoupled and filtered for good noise immunity since the audio performance of the device depends upon the PLL circuit. CLK (pin 27) ) s ( ct This is the master clock in used by the digital core. The master clock must be an integer multiple of the LR clock frequency. Typically, the master clock frequency is 12.288 MHz (256 * fs) for a 48 kHz sample rate; it is the default setting at power-up. Care must be taken to provide the device with the nominal system clock frequency; over-clocking the device may result in anomalous operation, such as inability to communicate. u d o r P e FILTER_PLL (pin 26) t e l o This is the connection for external filter components for the PLL loop compensation. The schematic diagram in Figure 5 on page 7 shows the recommended circuit. BICKI (pin 32) s b O The serial or bit clock input is for framing each data bit. The bit clock frequency is typically 64 * fs using I2S serial format. SDI_12 (pin 30) ) (s t c u This is the serial data input where PCM audio information enters the device. Six format choices are available including I2S, left or right justified, LSB or MSB first, with word widths of 16, 18, 20 and 24 bits. d o r P e LRCKI (pin 31) t e l o The left/right clock input is for data word framing. The clock frequency is at the input sample rate, fs. s b O 10/57 STA328 3 Electrical specifications Electrical specifications Table 3. Absolute maximum ratings Symbol Parameter Value Unit VDD33 3.3 V I/O power supply (pins VDDA, VDD) -0.5 to 4 V Vi Voltage on input pins -0.5 to (VDD33 + 0.5) V Vo Voltage on output pins -0.5 to (VDD33 + 0.5) V Tstg Storage temperature -40 to +150 C Tamb Ambient operating temperature -20 to +85 C VCC DC supply voltage (pins VCCnA, VCCnB) 40 VMAX Maximum voltage on VL (pin 20) 5.5 Table 4. Thermal data Symbol let Thermal resistance junction to case (thermal pad) Tj-SD Thermal shut-down junction temperature TWARN Thermal warning temperature Th-SD Thermal shut-down hysteresis Tj o s b O ) Typ V Max 2.5 Unit C/W 150 C 130 C 25 C Recommended operating conditions s ( t c Symbol Parameter Value u d o I/O power supply VDD33 u d o Min Rthj-case Table 5. V r P e Parameter ) s ( ct Pr Operating junction temperature Unit 3.0 to 3.6 V -20 to +125 C e interface specifications General t e ol 3.1 s b O Operating conditions VDD33 = 3.3 V 0.3 V, Tamb = 25 C unless otherwise specified Table 6. Symbol General interface electrical characteristics Parameter Test Condition Min. (1) Typ. Max. Unit 1 A Vi = VDD33 (1) 2 A IOZ 3-state output leakage without Vi = VDD33 (1) pull-up/down 2 A Vesd Electrostatic protection (human-body model) Iil Low level input no pull-up Vi = 0 V Iih High level input no pull-down Leakage current < 1 A 2000 V 1. The leakage currents are generally very small (< 1 nA). The values given here are the maximum values after an electrostatic stress on the pin. 11/57 Electrical specifications 3.2 STA328 DC electrical specifications (3.3 V buffers) Operating conditions VDD33 = 3.3 V 0.3 V, Tamb = 25 C unless otherwise specified Table 7. DC electrical specifications Symbol 3.3 Parameter Test condition Min. Typ. Max. Unit VIL Low level input voltage VIH High level input voltage 2.0 V Vhyst Schmitt trigger hysteresis 0.4 V Vol Low level output IoI = 2 mA Voh High level output Ioh = -2 mA 0.8 0.15 V V ) s ( ct VDD33 - 0.15 V u d o Power electrical specifications r P e Operating conditions VDD33 = 3.3 V 0.3 V, VL = 3.3 V, VCC = 30 V, Tamb = 25 C unless otherwise specified. Table 8. Symbol Min. -O Typ. Max. Unit Idss Power Pchannel/Nchannel leakage Idss gN Power Pchannel RdsON matching Id = 1 A 95 % Power Nchannel RdsON matching Id = 1 A 95 % Low current dead time (static) See test circuits, Figure 7 and Figure 8 td ON Turn-on delay time td OFF Dt_s ) s ( ct du o r P Id = 1A 200 VCC = 35 V m 50 A ns Resistive load 100 ns Turn-off delay time Resistive load 100 ns tr Rise time Resistive load, Figure 7 and Figure 8 25 ns tf Fall time Resistive load, Figure 7 and Figure 8 25 ns VCC Supply voltage 36 V VL Low logical state voltage VL VL = 3.3 V VH High logical state voltage VH VL = 3.3 V 1.7 V IVCC- Supply current from VCC in PWRDN Pin PWRDN = 0 V 3 mA Supply current from VCC in 3-state VCC = 30 V, 3-state IVCC-hiz 10 270 20 PWRDN 12/57 Test conditions Power Pchannel/Nchannel MOSFET RdsON ete b O bs Parameter RdsON gP l o s t e l o Power electrical characteristics 10 0.8 V 22 mA STA328 Electrical specifications Table 8. Power electrical characteristics (continued) Symbol Parameter Test conditions Typ. Input pulse width = 50% duty, switching frequency = 384 kHz, no LC filters IVCC Supply current from VCC in operation (both channel switching) Iout-sh Overcurrent protection threshold (short circuit current limit) VUV Undervoltage protection threshold tpw-min Output minimum pulse width No load Po Output power (refer to test circuit THD = 10% RL = 4, VCC = 21 V RL = 8, VCC = 36 V Po Output power (refer to test circuit THD = 1% RL = 4, VCC = 21 V RL = 8, VCC = 36 V Figure 7. Min. 4.5 s b O ) (s mA 6 A 7 V ) s ( ct 150 u d o 50 80 ns W W 40 62 t e l o Unit 80 70 r P e Test circuit 1 Max. W W OUTxY Vcc (3/4)Vcc Low current dead time = MAX(DTr, DTf) ct du (1/2)Vcc (1/4)Vcc +Vcc o r P t DTr Duty cycle = 50% e t e l M58 OUTxY INxY o s b O DTf R8W M57 + - V67 vdc = Vcc/2 gnd Figure 8. Test circuit 2 High Current Dead time for Bridge application = ABS(DTout(A)-DTin(A))+ABS(DTOUT(B)-DTin(B)) +VCC Duty cycle=A Duty cycle=B DTout(A) M58 DTin(A) Q1 Q2 Rload=4 OUTA INA Iout=1.5A M57 Q3 DTout(B) L67 10 C69 470nF L68 10 C71 470nF C70 470nF M64 DTin(B) OUTB INB Iout=1.5A Q4 Duty cycle A and B: Fixed to have DC output current of 4A in the direction shown in figure M63 D06AU1651 13/57 Electrical characteristics curves 4 STA328 Electrical characteristics curves Figure 9. Channel separation vs frequency +10 +0 dBr A -10 -20 ) s ( ct -30 -40 u d o -50 r P e -60 -70 t e l o -80 -90 20 50 100 bs 200 500 O ) 1k 2k 5k 10k 20k Hz s ( t c Figure 10. THD vs output power - single ended u d o 10 Pr 5 THD (%) e t e l o s b O Vcc = 36 V 2 RL = 4 1 f = 1 kHz 0.5 0.2 0.1 0.05 0.02 0.01 100m 200m 500m 1 2 5 Po (W) 14/57 10 20 50 60 STA328 Electrical characteristics curves Figure 11. THD vs output power - BTL 10 5 THD (%) Vcc = 36 V 2 Rl = 8 1 f = 1 kHz 0.5 0.2 ) s ( ct 0.1 0.05 u d o 0.02 0.01 100m 200m 500m 1 2 5 t e l o Po (W) Figure 12. THD vs frequency - BTL ) (s 1 t c u 0.5 THD (%) od e t e l O o s b Pr r P e 10 20 50 100 10k 20k s b O Vcc = 36 V RL = 8 0.2 f = 1 kHz 0.1 0.05 0.02 0.01 20 50 100 200 500 1k 2k 5k Hz 15/57 I2C bus specification STA328 I2C bus specification 5 The STA328 supports the I2C protocol. This protocol defines any device that sends data on to the I2C bus as a transmitter and any device that reads the data as a receiver. The device that controls the data transfer is known as the master and the other as the slave. The master always starts the transfer and provides the serial clock for synchronization. The STA328 is always a slave device in all of its communications. 5.1 Communication protocol ) s ( ct Data transition or change Data changes on the SDA line must only occur when the SCL clock is low. SDA transition while the clock is high is used to identify a START or STOP condition. u d o Start condition r P e START is identified by a high to low transition of the data bus SDA signal while the clock signal SCL is stable in the high state. A START condition must precede any command for data transfer. t e l o Stop condition s b O STOP is identified by a low to high transition of the data bus SDA signal while the clock signal SCL is stable in the high state. A STOP condition terminates communication between STA328 and the bus master. ) (s t c u Data input During the data input the STA328 samples the SDA signal on the rising edge of clock SCL. For correct device operation the SDA signal must be stable during the rising edge of the clock and the data can change only when the SCL line is low. d o r P e Device addressing t e ol 5.2 s b O To start communication between the master and the STA328, the master must initiate with a start condition. Following this, the master sends 8 bits (MSB first) onto the SDA line corresponding to the device select address and read or write mode. The 7 MSBs are the device address identifiers, corresponding to the I2C bus definition. The STA328 device address is decimal 34 (binary 00100010). The 8th bit (LSB) identifies read or write operation, RW. This bit is set to 1 in read mode and 0 for write mode. After a START condition the STA328 identifies the device address on the bus. If a match is found, it acknowledges the identification on the SDA bus during the 9th bit time. The byte following the device identification byte is the internal space address. 16/57 I2C bus specification STA328 5.3 Write operation Following the START condition the master sends a device select code with the RW bit set to 0. The STA328 acknowledges this and then the master writes the internal address byte. After receiving the internal byte address the STA328 again responds with an acknowledgement. Figure 13. I2C write procedure ACK ACK DEV-ADDR BYTE WRITE ACK SUB-ADDR DATA IN RW START STOP ACK MULTIBYTE WRITE ACK DEV-ADDR START ) s ( ct ACK SUB-ADDR ACK DATA IN DATA IN STOP RW u d o r P e Byte write In the byte write mode the master sends one data byte. This is acknowledged by the STA328. The master then terminates the transfer by generating a STOP condition. t e l o Multi-byte write s b O The multi-byte write modes can start from any internal address. Sequential data byte writes will be written to sequential addresses within the STA328. ) (s The master generating a STOP condition terminates the transfer. t c u 5.4 Read operation d o r Figure 14. I2C read procedure P e t e l o O bs CURRENT ADDRESS READ ACK DEV-ADDR NO ACK DATA RW START STOP ACK RANDOM ADDRESS READ DEV-ADDR RW RW= ACK HIGH START SEQUENTIAL CURRENT READ ACK ACK SUB-ADDR DEV-ADDR DEV-ADDR START NO ACK DATA RW ACK STOP ACK DATA DATA NO ACK DATA STOP START ACK SEQUENTIAL RANDOM READ DEV-ADDR START ACK ACK SUB-ADDR RW DEV-ADDR START ACK DATA RW ACK DATA NO ACK DATA STOP Current address byte read Following the START condition the master sends a device select code with the RW bit set to 1. The STA328 acknowledges this and then responds by sending one byte of data. The master then terminates the transfer by generating a STOP condition. 17/57 I2C bus specification STA328 Current address multi-byte read The multi-byte read modes can start from any internal address. Sequential data bytes will be read from sequential addresses within the STA328. The master acknowledges each data byte read and then generates a STOP condition terminating the transfer. Random address byte read Following the START condition the master sends a device select code with the RW bit set to 0. The STA328 acknowledges this and then the master writes the internal address byte. After receiving, the internal byte address the STA328 again responds with an acknowledgement. The master then initiates another START condition and sends the device select code with the RW bit set to 1. The STA328 acknowledges this and then responds by sending one byte of data. The master then terminates the transfer by generating a STOP condition. ) s ( ct Random address multi-byte read u d o The multi-byte read modes could start from any internal address. Sequential data bytes will be read from sequential addresses within the STA328. The master acknowledges each data byte read and then generates a STOP condition terminating the transfer. r P e t e l o ) (s t c u d o r P e t e l o s b O 18/57 s b O STA328 6 Register description Register description You must not reprogram the register bits marked "Reserved". It is important that these bits keep their default reset values. Table 9. Address Register summary Name D7 D6 D5 D4 D3 D2 D1 D0 0x00 ConfA FDRB TWAB TWRB IR1 IR0 MCS2 MCS1 MCS0 0x01 ConfB C2IM C1IM DSCKE SAIFB SAI3 SAI2 SAI1 SAI0 0x02 ConfC Reserved CSZ4 CSZ3 CSZ2 CSZ1 CSZ0 OM1 OM0 0x03 ConfD MME ZDE DRC BQL PSL DSPB DEMP 0x04 ConfE SVE ZCE Reserved PWMS AME Reserved MPC 0x05 ConfF EAPD PWDN ECLE 0x06 Mmute Reserved Reserved Reserved Reserved Reserved Reserved Reserved MMute 0x07 Mvol MV7 MV6 MV5 MV4 MV3 MV2 MV1 MV0 0x08 C1Vol C1V7 C1V6 C1V5 C1V4 C1V3 C1V2 C1V1 C1V0 0x09 C2Vol C2V7 C2V6 C2V5 C2V4 C2V3 C2V2 C2V1 C2V0 0x0A C3Vol C3V7 C3V6 C3V5 C3V3 C3V2 C3V1 C3V0 0x0B Auto1 AMPS Reserved AMGC1 AMGC0 AMV1 AMV0 AMEQ1 AMEQ0 0x0C Auto2 XO3 XO2 b O XO1 AMAM2 AMAM1 AMAM0 AMAME 0x0D Auto3 Reserved Reserved Reserved PEQ4 PEQ3 PEQ2 PEQ1 PEQ0 0x0E C1Cfg C1OM1 C1OM0 C1LS1 C1LS0 C1BO C1VBP C1EQBP C1TCB 0x1F C2Cfg C2OM1 C2OM0 C2LS1 C2LS0 C2BO C2VBP C2EQBP C2TCB 0x10 C3Cfg C3OM1 C3OM0 C3LS1 C3LS0 C3BO C3VBP Reserved Reserved 0x11 Tone TTC3 TTC2 TTC1 TTC0 BTC3 BTC2 BTC1 BTC0 L1ar L1A3 L1A2 L1A1 L1A0 L1R3 L1R2 L1R1 L1R0 L1atrt L1AT3 L1AT2 L1AT1 L1AT0 L1RT3 L1RT2 L1RT1 L1RT0 L2ar L2A3 L2A2 L2A1 L2A0 L2R3 L2R2 L2R1 L2R0 0x15 L2atrt L2AT3 L2AT2 L2AT1 L2AT0 L2RT3 L2RT2 L2RT1 L2RT0 0x16 Cfaddr2 CFA7 CFA6 CFA5 CFA4 CFA3 CFA2 CFA1 CFA0 0x17 B1cf1 C1B23 C1B22 C1B21 C1B20 C1B19 C1B18 C1B17 C1B16 0x18 B1cf2 C1B15 C1B14 C1B13 C1B12 C1B11 C1B10 C1B9 C1B8 0x19 B1cf3 C1B7 C1B6 C1B5 C1B4 C1B3 C1B2 C1B1 C1B0 0x1A B2cf1 C2B23 C2B22 C2B21 C2B20 C2B19 C2B18 C2B17 C2B16 0x1B B2cf2 C2B15 C2B14 C2B13 C2B12 C2B11 C2B10 C2B9 C2B8 0x1C B2cf3 C2B7 C2B6 C2B5 C2B4 C2B3 C2B2 C2B1 C2B0 0x1D A1cf1 C3B23 C3B22 C3B21 C3B20 C3B19 C3B18 C3B17 C3B16 e t e ol 0x12 0x13 s b O 0x14 s ( t c u d o Pr )- XO1 Reserved BCLE C3V4 so u d o IDE e t e l ) s ( ct Pr OCFG1 HPB MPCV OCFG0 19/57 Register description Table 9. Address STA328 Register summary Name D7 D6 D5 D4 D3 D2 D1 D0 0x1E A1cf2 C3B15 C3B14 C3B13 C3B12 C3B11 C3B10 C3B9 C3B8 0x1F A1cf3 C3B7 C3B6 C3B5 C3B4 C3B3 C3B2 C3B1 C3B0 0x20 A2cf1 C4B23 C4B22 C4B21 C4B20 C4B19 C4B18 C4B17 C4B16 0x21 A2cf2 C4B15 C4B14 C4B13 C4B12 C4B11 C4B10 C4B9 C4B8 0x22 A2cf3 C4B7 C4B6 C4B5 C4B4 C4B3 C4B2 C4B1 C4B0 0x23 B0cf1 C5B23 C5B22 C5B21 C5B20 C5B19 C5B18 C5B17 C5B16 0x24 B0cf2 C5B15 C5B14 C5B13 C5B12 C5B11 C5B10 C5B9 C5B8 0x25 B0cf3 C5B7 C5B6 C5B5 C5B4 C5B3 C5B2 C5B1 0x26 Cfud Reserved Reserved Reserved Reserved RA R1 WA 0x27 MPCC1 MPCC15 MPCC14 MPCC13 MPCC12 MPCC11 MPCC10 MPCC9 MPCC8 0x28 MPCC2 MPCC7 MPCC3 MPCC2 MPCC0 0x29 ro Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved 0x2A Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved 0x2B FDRC1 FDRC15 FDRC14 FDRC13 FDRC12 0x2C FDRC2 FDRC7 FDRC6 FDRC5 FDRC4 0x2D Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved MPCC6 MPCC5 MPCC4 P e bs t e l o du MPCC1 Reserved FDRC10 FDRC9 FDRC8 FDRC3 FDRC2 FDRC1 FDRC0 Reserved D7 D6 D5 D4 D3 D2 D1 D0 FDRB TWAB TWRB IR1 IR0 MCS2 MCS1 MCS0 0 1 1 0 0 0 1 1 Table 10. Bit s b O W1 FDRC11 O Configuration register) A (addr 0x00) s ( t c u d o r P e t e ol 6.1 ) s ( ct C5B0 Master clock select R/W RST Name 0 RW 1 MCS0 1 RW 1 MCS1 2 RW 0 MCS2 Description Master clock select: Selects the ratio between the input I2S sample frequency and the input clock. The STA328 will support sample rates of 32 kHz, 44.1 kHz, 48 kHz, 88.2 kHz, and 96 kHz. Therefore the internal clock will be: " 32.768 MHz for 32 kHz " 45.1584 MHz for 44.1 kHz, 88.2 kHz, and 176.4 kHz " 49.152 MHz for 48 kHz, 96 kHz, and 192 kHz The external clock frequency provided to the XTI pin must be a multiple of the input sample frequency (fs). The correlation between the input clock and the input sample rate is determined by the status of the MCSx bits and the IR (input rate) register bits. The MCSx 20/57 STA328 Register description bits determine the PLL factor generating the internal clock and the IR bit determines the oversampling ratio used internally. Table 11. IR and MCS settings for input sample rate and clock rate Input sample rate IR fs (kHz) MCS[2:0] 000 001 010 011 100 101 32, 44.1, 48 00 768 fs 512 fs 384 fs 256 fs 128 fs 576 fs 88.2, 96 01 384 fs 256 fs 192 fs 128 fs 64 fs x 176.4, 192 1X 384 fs 256 fs 192 fs 128 fs 64 fs x Table 12. Bit 4:3 ) s ( ct Interpolation ratio select R/W RST RW 00 Name Description u d o Interpolation ratio select: selects internal interpolation ratio based on input I2S sample frequency IR[1:0] r P e The STA328 has variable interpolation (re-sampling) settings such that internal processing and DDX(R) output rates remain consistent. The first processing block interpolates by either 2 times or 1 time (pass-through) or provides a down-sample by a factor of 2. t e l o The IR bits determine the re-sampling ratio of this interpolation. Table 13. Input sample rate fs (kHz) 00 44.1 u d o 48 96 e t e l 176.4 O o s b Pr 192 Table 14. Bit 5 )- IR[1,0] s ( t c 32 88.2 s b O IR bit settings as a function of input sample rate 1st stage interpolation ratio 2 times over-sampling 00 2 times over-sampling 00 2 times over-sampling 01 Pass-through 01 Pass-through 10 Down-sampling by 2 10 Down-sampling by 2 Thermal warning recovery bypass R/W RST RW 1 Name TWRB Description Thermal warning recovery bypass: 0: thermal warning recovery enabled 1: thermal warning recovery disabled If the thermal warning adjustment is enabled (TWAB = 0), then the thermal warning recovery will determine if the adjustment is removed when thermal warning is negative. If TWRB = 0 and TWAB = 0, then when a thermal warning disappears the gain adjustment determined by the thermal warning post-scale (default = -3 dB) will be removed and the gain will be added back to the system. If TWRB = 1 and TWAB = 0, then when a thermal warning disappears the thermal warning post-scale gain adjustment will remain until TWRB is changed to zero or the device is reset. 21/57 Register description STA328 Table 15. Bit 6 Thermal warning adjustment bypass R/W RW RST 1 Name TWAB Description Thermal warning adjustment bypass: 0: thermal warning adjustment enabled 1: thermal warning adjustment disabled The on-chip STA328 power output block provides feedback to the digital controller using inputs to the power control block. The TWARN input is used to indicate a thermal warning condition. When TWARN is asserted (set to 0) for a period greater than 400 ms, the power control block will force an adjustment to the modulation limit in an attempt to eliminate the thermal warning condition. Once the thermal warning volume adjustment is applied, whether the gain is reapplied when TWARN is de-asserted is dependent on the TWRB bit. Table 16. Bit 7 ) s ( ct Fault detect recovery bypass R/W RW RST 0 Name FDRB u d o Description Fault detector recovery bypass: 0: fault detector recovery enabled 1: fault detector recovery disabled r P e t e l o The DDX(R) power block can provide feedback to the digital controller using inputs to the power control block. The FAULT input is used to indicate a fault condition (either over-current or thermal). When FAULT is asserted (set to 0), the power control block will attempt a recovery from the fault by asserting the 3-state output (setting it to 0 which directs the power output block to begin recovery). It holds it at 0 for period of time in the range of 0.1 ms to 1 s as defined by the fault-detect recovery constant register (FDRC registers 0x29 to 0x2A), then toggle it back to 1. This sequence is repeated as log as the fault indication exists. This feature is enabled by default but can be bypassed by setting the FDRB control bit to 1. ) (s t c u d o r P e t e l o s b O 22/57 s b O STA328 6.2 Register description Configuration register B (addr 0x01) D7 D6 D5 D4 D3 D2 D1 D0 C2IM C1IM DSCKE SAIFB SAI3 SAI2 SAI1 SAI0 1 0 0 0 0 0 0 0 This register configures the serial data interface Table 17. Bit Serial audio input interface format R/W RST Name Description 3:0 RW 0000 SAI[3:0] Serial audio input interface format: determines the interface format of the input serial digital audio interface (see below). 4 RW 0 SAIFB Data format: 0: MSB first ) s ( ct 1: LSB first u d o The STA328 serial audio input was designed to interface with standard digital audio components and to accept a number of serial data formats. The STA328 always acts as a slave when receiving audio input from standard digital audio components. Serial data for two channels is provided using 3 input pins: left/right clock LRCKI (pin 31), serial clock BICKI (pin 32), and serial data SDI (pin 30). r P e t e l o SAI[3:0] and SAIFB are used to specify the serial data format. The default format is I2S, MSB-first. Available formats are shown below in Figure 15 and the tables that follow. s b O Figure 15. General serial input and output formats ) (s I2S Left LRCLK t c u SCLK SDATA MSB d o r Right LSB MSB LSB MSB Left Justified P e let O o s b Left LRCLK Right SCLK SDATA MSB LSB MSB LSB MSB Right Justified Left LRCLK Right SCLK SDATA MSB LSB MSB LSB MSB Table 18 lists the serial audio input formats supported by STA328 when BICKI = 32 * fs, 48 * fs and 64 * fs, where the sampling rate fs = 32, 44.1, 48, 88.2, 96, 176.4 or 192 kHz. 23/57 Register description Table 18. STA328 Supported serial audio input formats BICKI 32 * fs 48 * fs 64 * fs SAI [3:0] X I2S 15-bit data 1110 X Left/right justified 16-bit data 0100 X I2S 23-bit data 0100 X I2S 20-bit data 1000 X I2S 18-bit data 0100 0 MSB first I2S 16-bit data 1100 1 LSB first I2S 16-bit data 0001 X Left-justified 24-bit data 0101 X Left-justified 20-bit data 1001 X Left-justified 18-bit data 1101 X Left-justified 16-bit data 0010 X Right-justified 24-bit data 0110 X Right-justified 20-bit data 1010 X Right-justified 18-bit Data 1110 X 0000 X 0100 X 1000 s ( t c s b O Right-justified 16-bit Data I2S 24-bit data I2S 20-bit data 0 MSB first I2S 16-bit data 1 LSB first I2S 16-bit data 0001 X Left-justified 24-bit data 0101 X Left-justified 20-bit data 1001 X Left-justified 18-bit data 1101 X Left-justified 16-bit data 0010 X Right-justified 24-bit data 0110 X Right-justified 20-bit data 1010 X Right-justified 18-bit data 1110 X Right-justified 16-bit data o r P u d o t e l o I2S 18-bit data du O )- ) s ( ct r P e X 1100 o s b Interface format 1100 0000 e t e l SAIFB For example, SAI = 1110 and SAIFB = 1 would specify right-justified 16-bit data, LSB-first. 24/57 STA328 Register description Table 19. Serial input data timing characteristics (fs = 32 to 192 kHz) Parameter in Figure 16 Value BICKI frequency (slave mode) 12.5 MHz max. BICKI pulse width low (T0) (slave mode) 40 ns min. BICKI pulse width high (T1) (slave mode) 40 ns min. BICKI active to LRCKI edge delay (T2) 20 ns min. BICKI active to LRCKI edge delay (T3) 20 ns min. SDI valid to BICKI active setup (T4) 20 ns min. BICKI active to SDI hold time (T5) 20 ns min. ) s ( ct Figure 16. Serial input data timing T2 T3 LRCKI T1 r P e T0 BICKI T4 t e l o SDI T5 Table 20. Bit 5 0 s b O Name s ( t c u d o r P e t e l o )- RST RW Bit s b O Delay serial clock enable R/W Table 21. u d o DSCKE Description Delay serial clock enable: 0: no serial clock delay 1: serial clock delay by 1 core clock cycle to tolerate anomalies in some I2S master devices Channel input mapping R/W RST Name Description 6 RW 0 C1IM 0: processing channel 1 receives left I2S input 1: processing channel 1 receives right I2S input 7 RW 1 C2IM 0: processing channel 2 receives left I2S input 1: processing channel 2 receives right I2S input Each channel received via I2S can be mapped to any internal processing channel via the channel input mapping registers. This allows for flexibility in processing. The default settings of these registers map each I2S input channel to its corresponding processing channel. 25/57 Register description 6.3 STA328 Configuration register C (addr 0x02) D7 D6 D5 D4 D3 D2 D1 D0 Reserved CSZ4 CSZ3 CSZ2 CSZ1 CSZ0 OM1 OM0 0 1 0 0 0 0 1 0 DDX(R) power output mode 6.3.1 DDX(R) power output mode Table 22. Bit 1:0 R/W RW RST 10 Name Description DDX(R) power output mode: Selects configuration of DDX(R) output. OM[1:0] ) s ( ct The DDX(R) power output mode selects how the DDX(R) output timing is configured. Different power devices can use different output modes. The recommended use is OM = 10. When OM = 11 the CSZ bits determine the size of the DDX(R) compensating pulse. u d o r P e DDX(R) output modes Table 23. t e l o OM[1,0] Output stage - mode 00 Not used 01 Not used 10 Recommended ) (s 11 s b O Variable compensation t c u DDX(R) variable compensating pulse size 6.3.2 d o r The DDX(R) variable compensating pulse size is intended to adapt to different power stage ICs. Contact Apogee applications for support when deciding this function. P e Table 24. t e l o bs O 26/57 DDX(R) compensating pulse CSZ[4:0] Compensating pulse size 00000 0 clock period compensating pulse size 00001 1 clock period compensating pulse size ... ... 10000 16 clock period compensating pulse size ... ... 11111 31 clock period compensating pulse size STA328 6.4 Register description Configuration register D (addr 0x03) D7 D6 D5 D4 D3 D2 D1 D0 MME ZDE DRC BQL PSL DSPB DEMP HPB 0 1 0 0 0 0 0 0 Table 25. Bit 0 High-pass filter bypass R/W RW RST 0 Name Description High-pass filter bypass bit. 0: AC coupling high pass filter enabled 1: AC coupling high pass filter disabled HPB ) s ( ct The STA328 features an internal digital high-pass filter for the purpose of DC Blocking. The purpose of this filter is to prevent DC signals from passing through a DDX(R) amplifier. DC signals can cause speaker damage. Table 26. Bit 1 u d o De-emphasis R/W RW RST r P e 0 Name DEMP Description t e l o De-emphasis: 0: no de-emphasis 1: de-emphasis s b O By setting this bit to 1, the de-emphasis will be implemented on all channels. DSPB (DSP Bypass, Bit D2, CFA) bit must be set to 0 for de-emphasis to function. Table 27. Bit 2 DSP bypass R/W RW ct u d o r P e t e l o RST 0 ) (s Name DSPB Description DSP bypass bit: 0: normal Operation 1: bypass of EQ and mixing functionality Setting the DSPB bit bypasses all the EQ and mixing functionality of the STA328 core. s b O Table 28. Bit 3 Post-scale link R/W RW RST 0 Name PSL Description Post-scale link: 0: each channel uses individual post-scale value 1: each channel uses channel 1 post-scale value Post-scale functionality is an attenuation placed after the volume control and directly before the conversion to PWM. Post-scale can also be used to limit the maximum modulation index and therefore the peak current. A setting of 1 in the PSL register will result in the use of the value stored in channel 1 post-scale for all three internal channels. 27/57 Register description STA328 Table 29. Bit 4 Biquad coefficient link R/W RW RST 0 Name Description Biquad Link: 0: each channel uses coefficient values 1: each channel uses channel 1 coefficient values BQL For ease of use, all channels can use the biquad coefficients loaded into the channel 1 coefficient RAM space by setting the BQL bit to 1. Therefore, any EQ updates only have to be performed once. Table 30. Bit 5 Dynamic range compression/anti-clipping bit R/W RW RST 0 Name ) s ( ct Description Dynamic range compression/anti-clipping 0: limiters act in anti-clipping mode 1: limiters act in dynamic range compression mode DRC u d o r P e Both limiters can be used in one of two ways, anti-clipping or dynamic range compression. When used in anti-clipping mode the limiter threshold values are constant and dependent on the limiter settings. In dynamic range compression mode the limiter threshold values vary with the volume settings allowing a nighttime listening mode that provides a reduction in the dynamic range regardless of the volume level. Table 31. Bit 6 s b O Zero detect mute enable R/W RW RST )- Name s ( t c 1 ZDE t e l o Description Zero detect mute enable: setting of 1 enables the automatic zero-detect mute u d o Setting the ZDE bit enables the zero-detect automatic mute. When ZDE = 1, the zero detect circuit looks at the input data to each processing channel after the channel-mapping block. If any channel receives 2048 consecutive zero value samples (regardless of fs) then that individual channel is muted if this function is enabled. r P e let Table 32. so b O 28/57 Bit 7 Miami mode enable R/W RW RST 0 Name MME Description Miami mode enable: 0: sub mix into left/right disabled 1: sub mix into left/right enabled STA328 6.5 Register description Configuration register E (addr 0x04) D7 D6 D5 D4 D3 D2 D1 D0 SVE ZCE Reserved PWMS AME Reserved MPC MPCV 1 1 0 0 0 0 1 0 Table 33. Bit Max power correction variable R/W 0 RW RST Name 0 MPCV Description Max power correction variable: 0: use standard MPC coefficient 1: use MPCC bits for MPC coefficient ) s ( ct By enabling MPC and setting MPCV = 1, the max power correction becomes variable. By adjusting the MPCC registers (address 0x27, 0x28) it becomes possible to adjust the THD at maximum unclipped power to a lower value for a particular application. Table 34. Bit R/W 1 u d o Max power correction RW RST r P e Name 1 Description Max power correction: 0: MPC disabled 1: MPC enabled t e l o MPC s b O Setting the MPC bit corrects the DDX(R) power device at high power. This mode lowers the THD+N of a full DDX(R) system at maximum power output and slightly below. Table 35. Bit R/W 3 ct RST du o r P RW 0 Name Description AM mode enable: 0: normal DDX(R) operation. 1: AM reduction mode DDX(R) operation. AME The STA328 features a DDX(R) processing mode that minimizes the amount of noise generated in the frequency range of AM radio. This mode is intended for use when DDX(R) is operating in a device with an active AM tuner. The SNR of the DDX(R) processing is reduced to approximately 83 dB in this mode, which is still greater than the SNR of AM radio. e t e ol s b O ) (s AM mode enable Table 36. Bit 4 PWM speed mode R/W RW Table 37. RST 0 Name PWMS Description PWM speed selection: normal or odd PWM output speed selections PWMS[1:0] PWM output speed 0 Normal speed (384 kHz) all channels 1 Odd speed (341.3 kHz) all channels 29/57 Register description STA328 Table 38. Bit 6 Zero-crossing volume enable R/W RW RST 1 Name Description Zero-crossing volume enable: 1: volume adjustments will only occur at digital zerocrossings 0: volume adjustments will occur immediately ZCE The ZCE bit enables zero-crossing volume adjustments. When volume is adjusted on digital zero-crossings no clicks will be audible. Table 39. Bit 7 Soft volume update enable R/W RW RST 1 Name ) s ( ct Description Soft volume enable: 1: volume adjustments will use soft volume 0: volume adjustments will occur immediately SVE u d o r P e The STA328 includes a soft volume algorithm that will step through the intermediate volume values at a predetermined rate when a volume change occurs. By setting SVE = 0 this can be bypassed and volume changes will jump from old to new value directly. This feature is only available if individual channel volume bypass bit is set to 0. t e l o ) (s t c u d o r P e t e l o s b O 30/57 s b O STA328 6.6 Register description Configuration register F (addr 0x05) D7 D6 D5 D4 D3 D2 D1 D0 EAPD PWDN ECLE Reserved BCLE IDE OCFG1 OCFG0 0 1 0 1 1 1 0 0 Table 40. Bit 1:0 Output configuration selection R/W RW RST Table 41. 00 Name OCFG[1:0] Description Output configuration selection 00: 2-channel (full-bridge) power, 1-channel DDX(R) is default OCFG[1:0] 00 01 2 (half-bridge) and 1 (full-bridge) on-board power: 1A 1A binary 2A 1B binary 3A/3B 2A/2B binary 10 Reserved 11 1 channel mono-parallel: 3A 1A/1B 3B 2A/2B u d o r P e t e l o ) (s Table 42. Bit t c u s b O Invalid input detect mute enable d o r R/W P e t e l o s b O Output power configuration 2 channel (full-bridge) power, 1 channel DDX(R): 1A/1B 1A/1B 2A/2B 2A/2B 2 ) s ( ct Output configuration selection RW RST 1 Name Description Invalid input detect auto-mute enable: 0: disabled 1: enabled IDE Setting the IDE bit enables this function, which looks at the input I2S data and clocking and will automatically mute all outputs if the signals are perceived as invalid. Table 43. Bit 3 Binary clock loss detection enable R/W RW RST 1 Name BCLE Description Binary output mode clock loss detection enable 0: disabled 1: enabled Detects loss of input MCLK in binary mode and will output 50% duty cycle to prevent audible artifacts when input clocking is lost. 31/57 Register description STA328 Table 44. Bit 5 Auto-EAPD on clock loss enable R/W RW RST 0 Name Description Auto EAPD on clock loss 0: disabled 1: enabled ECLE When ECLE is active, it issues a power device power down signal (EAPD) on clock loss detection. Table 45. Bit 6 Software power down R/W RW RST Table 46. Bit 7 1 Name Description PWDN u d o r P e External amplifier power down R/W RW RST let Name 0 ) s ( ct Software power down: 0: power down mode: initiates a power-down sequence which results in a soft mute of all channels and finally asserts EAPD circa 260 ms later 1: normal operation EAPD o s b Description External amplifier power down: 0: external power stage power down active 1: normal operation O ) EAPD is used to actively power down a connected DDX(R) power device. This register has to be written to 1 at start-up to enable the DDX(R) power device for normal operation. s ( t c u d o r P e t e l o s b O 32/57 STA328 Register description 6.7 Volume control 6.7.1 Master controls Master mute register (addr 0x06) D7 D6 D5 D4 D3 D2 D1 D0 Reserved Reserved Reserved Reserved Reserved Reserved Reserved MMUTE 0 0 0 0 0 0 0 0 Master volume register (addr 0x07) D7 D6 D5 D4 D3 D2 D1 MV7 MV6 MV5 MV4 MV3 MV2 MV1 1 1 1 1 1 1 1 D0 ) s ( ct MV0 1 u d o Note: Value of volume derived from MVOL is dependent on AMV AutoMode volume settings. 6.7.2 Channel controls Channel 1 volume (addr 0x08) D7 D6 D5 D4 C1V7 C1V6 C1V5 C1V4 0 1 1 0 t e l o D3 bs O ) r P e D2 D1 D0 C1V3 C1V2 C1V1 C1V0 0 0 0 0 Channel 2 volume (addr 0x09) D7 D6 C2V7 C2V6 s ( t c du 0 1 o r P D4 D3 D2 D1 D0 C2V5 D5 C2V4 C2V3 C2V2 C2V1 C2V0 1 0 0 0 0 0 Channel 3 volume (addr 0x0A) D7 e t e ol C3V7 0 s b O 6.7.3 D6 D5 D4 D3 D2 D1 D0 C3V6 C3V5 C3V4 C3V3 C3V2 C3V1 C3V0 1 1 0 0 0 0 0 Volume description The volume structure of the STA328 consists of individual volume registers for each of the three channels and a master volume register, and individual channel volume trim registers. The channel volume settings are normally used to set the maximum allowable digital gain and to hard-set gain differences between certain channels. These values are normally set at the initialization of the IC and not changed. The individual channel volumes are adjustable in 0.5-dB steps from +48 dB to -80 dB. The master volume control is normally mapped to the master volume of the system. The values of these two settings are summed to find the actual gain/volume value for any given channel. When set to 1, the master mute will mute all channels, whereas the individual channel mutes (CxM) will mute only that channel. Both the master mute and the channel mutes provide a "soft mute" with the volume ramping down to mute in 4096 samples from the maximum volume setting at the internal processing rate (approximately 96 kHz). A "hard 33/57 Register description STA328 mute" can be obtained by programming the value 0xFF to any channel volume register or the master volume register. When volume offsets are provided via the master volume register any channel whose total volume is less than -100 dB will be muted. All changes in volume take place at zero-crossings when ZCE = 1 (configuration register E) on a per channel basis as this creates the smoothest possible volume transitions. When ZCE = 0, volume updates will occur immediately. The STA328 also features a soft-volume update function that will ramp the volume between intermediate values when the value is updated, when SVE = 1 (configuration register E). This feature can be disabled by setting SVE = 0. Each channel also contains an individual channel volume bypass. If a particular channel has volume bypassed via the CxVBP = 1 register then only the channel volume setting for that particular channel affects the volume setting, the master volume setting will not affect that channel. Also, master soft-mute will not affect the channel if CxVBP = 1. ) s ( ct Each channel also contains a channel mute. If CxM = 1 a soft mute is performed on that channel Table 47. Volume offset from channel value 00000000 (0x00) 0 dB 00000001 (0x01) -0.5 dB 00000010 (0x02) -1 dB ... ... ) (s 01001100 (0x4C) -38 dB ct ... du 11111110 (0xFE) o r P 11111111 (0xFF) Table 48. e t e l o s b O 34/57 r P e Master volume offset as a function of MV[7:0] MV[7:0] u d o t e l o s b O ... -127 dB Hard master mute Channel volume as a function of CxV[7:0] CxV[7:0] Volume 00000000 (0x00) +48 dB 00000001 (0x01) +47.5 dB 00000010 (0x02) +47dB ... ... 01100001 (0x5F) +0.5 dB 01100000 (0x60) 0 dB 01011111 (0x61) -0.5 dB ... ... 11111110 (0xFE) -79.5 dB 11111111 (0xFF) Hard channel mute STA328 Register description 6.8 AutoMode registers 6.8.1 AutoModes EQ, volume, GC (addr 0x0B) D7 D6 D5 D4 D3 D2 D1 D0 AMPS Reserved AMGC1 AMGC0 AMV1 AMV0 AMEQ1 AMEQ0 1 0 0 0 0 0 0 0 Table 49. AutoMode EQ AMEQ[1,0] Mode (biquad 1-4) 00 User programmable 01 Preset EQ - PEQ bits 10 Auto volume controlled loudness curve 11 Not used ) s ( ct u d o By setting AMEQ to any setting other than 00 enables AutoMode EQ where biquads 1-4 are not user programmable. Any coefficient settings for these biquads are ignored. Also when AutoMode EQ is used the pre-scale value for channels 1-2 becomes hard-set to -18 dB. Table 50. r P e t e l o AutoMode volume bs AMV[1,0] Mode (MVOL) 00 MVOL 0.5 dB 256 steps (standard) 01 MVOL auto curve 30 steps O ) t(s 10 MVOL auto curve 40 steps c u d 11 Table 51. MVOL auto curve 50 steps AutoMode gain compression/limiters o r P AMGC[1:0] 00 s b O e t e ol Mode User programmable GC 01 AC no clipping 10 AC limited clipping (10%) 11 DRC nighttime listening mode Table 52. Bit 0 AMPS - AutoMode auto prescale R/W RW RST 0 Name AMPS Description AutoMode pre-scale 0: -18 dB used for pre-scale when AMEQ neq 00 1: user defined pre-scale when AMEQ neq 00 35/57 Register description 6.8.2 STA328 AutoMode AM/pre-scale/bass management scale (addr 0x0C) D7 D6 D5 D4 D3 D2 D1 D0 XO3 XO2 XO1 XO0 AMAM2 AMAM1 AMAM0 AMAME 0 0 0 0 0 0 0 0 Table 53. Bit AutoMode AM switching enable R/W RST Name Description 0 RW 0 AMAME AutoMode AM enable 0: switching frequency determined by PWMS setting 1: switching frequency determined by AMAM settings 3:1 RW 000 AMAM[2:0] AM switching frequency setting Default: 000 n Table 54. u d o AutoMode AM switching frequency selection AMAM[2:0] 48 kHz/96 kHz input fs ) s ( ct 44.1 kHz/88.2 kHz input fs r P e 000 0.535 MHz -0.720 MHz 0.535 MHz -0.670 MHz 001 0.721 MHz -0.900 MHz 0.671 MHz -0.800 MHz 010 0.901 MHz -1.100 MHz 011 1.101 MHz -1.300 MHz 100 1.301 MHz -1.480 MHz 101 1.481 MHz -1.600 MHz 1.341 MHz -1.500 MHz 110 1.601 MHz -1.700 MHz 1.501 MHz - 1.700 MHz )- s b O t e l o s ( t c 0.801 MHz -1.000 MHz 1.001 MHz -1.180 MHz 1.181 MHz -1.340 MHz When DDX(R) is used concurrently with an AM radio tuner, it is advisable to use the AMAM bits to automatically adjust the output PWM switching rate dependent upon the specific radio frequency that the tuner is receiving. The values used in AMAM are also dependent upon the sample rate determined by the ADC used. u d o r P e Table 55. t e l o Bit s b O 7:4 AutoMode crossover setting R/W RW Table 56. RST 0 Name XO[3:0] AutoMode crossover frequency selection 000: user defined crossover coefficients are used Otherwise: preset coefficients for the crossover setting desired Crossover frequency selection XO[2:0] 36/57 Description Bass management - Crossover frequency 0000 User 0001 80 Hz 0010 100 Hz 0011 120 Hz 0100 140 Hz STA328 Register description Table 56. Crossover frequency selection (continued) XO[2:0] 6.8.3 Bass management - Crossover frequency 0101 160 Hz 0110 180 Hz 0111 200 Hz 1000 220 Hz 1001 240 Hz 1010 260 Hz 1011 280 Hz 1100 300 Hz 1101 320 Hz 1110 340 Hz 1111 360 Hz u d o Preset EQ settings (addr 0x0D) D7 D6 D5 D4 Reserved Reserved Reserved PEQ4 0 0 0 0 Table 57. Preset EQ selection ) (s PEQ[3:0] d o r 00010 P e let o s b D2 D1 D0 PEQ3 PEQ2 PEQ1 PEQ0 0 0 0 s b O 0 t e l o Setting Flat 00001 00011 D3 r P e t c u 00000 O ) s ( ct Rock Soft rock Jazz 00100 Classical 00101 Dance 00110 Pop 00111 Soft 01000 Hard 01001 Party 01010 Vocal 01011 Hip-hop 01100 Dialog 01101 Bass-boost #1 01110 Bass-boost #2 01111 Bass-boost #3 10000 Loudness 1 (least boost) 37/57 Register description Table 57. STA328 Preset EQ selection (continued) PEQ[3:0] Setting 10001 Loudness 2 10010 Loudness 3 10011 Loudness 4 10100 Loudness 5 10101 Loudness 6 10110 Loudness 7 10111 Loudness 8 11000 Loudness 9 11001 Loudness 10 11010 Loudness 11 11011 Loudness 12 11100 Loudness 13 11101 Loudness 14 11110 Loudness 15 11111 Loudness 16 (most boost) ) (s ) s ( ct u d o r P e s b O 6.9 Channel configuration registers 6.9.1 Channel 1 configuration (addr 0x0E) D6 Pr C1OM1 0 e t e ol 6.9.2 s b O 6.9.3 t c u od D7 t e l o D5 D4 D3 D2 D1 D0 C1OM0 C1LS1 C1LS0 C1BO C1VBP C1EQBP C1TCB 0 0 0 0 0 0 0 Channel 2 configuration (addr 0x0F) D7 D6 D5 D4 D3 D2 D1 D0 C2OM1 C2OM0 C2LS1 C2LS0 C2BO C2VBP C2EQBP C2TCB 0 0 0 0 0 0 0 0 Channel 3 configuration (addr 0x10) D7 D6 D5 D4 D3 D2 D1 D0 C3OM1 C3OM0 C3LS1 C3LS0 C3BO C3VBP Reserved Reserved 0 0 0 0 0 0 0 0 EQ control can be bypassed on a per channel basis. If EQ control is bypassed on a given channel the prescale and all 9 filters (high-pass, biquads, de-emphasis, bass management cross-over, bass, treble in any combination) are bypassed for that channel. 38/57 STA328 Register description CxEQBP: " 0 perform EQ on channel X - normal operation " 1 bypass EQ on channel X Tone control (bass/treble) can be bypassed on a per channel basis. If tone control is bypassed on a given channel the two filters that tone control utilizes are bypassed. CxTCB: " 0 perform tone control on channel x - (default operation) " 1 bypass tone control on channel x Each channel can be configured to output either the patented DDX(R) PWM data or standard binary PWM encoded data. By setting the CxBO bit to 1, each channel can be individually controlled to be in binary operation mode. ) s ( ct Also, there is the capability to map each channel independently onto any of the two limiters available within the STA328 or even not map it to any limiter at all (default mode). Table 58. u d o r P e Channel limiter mapping selection CxLS[1,0] Channel limiter mapping t e l o 00 Channel has limiting disabled 01 Channel is mapped to limiter #1 10 Channel is mapped to limiter #2 ) (s s b O Each PWM Output Channel can receive data from any channel output of the volume block. Which channel a particular PWM output receives is dependent upon that channel's CxOM register bits. Table 59. t c u Channel PWM output mapping CxOM[1:0] d o r 00 P e 01 let 10 o s b 11 PWM output from Channel 1 Channel 2 Channel 3 Not used O 39/57 Register description 6.10 STA328 Tone control (addr 0x11) D7 D6 D5 D4 D3 D2 D1 D0 TTC3 TTC2 TTC1 TTC0 BTC3 BTC2 BTC1 BTC0 0 1 1 1 0 1 1 1 Table 60. Tone control boost/cut selection BTC[3:0]/TTC[3:0] 0000 -12 dB 0001 -12 dB ... ... 0111 -4 dB 0110 -2 dB 0111 0 dB 1000 +2 dB 1001 +4 dB ... ... 1101 +12 dB 1110 +12 dB 1111 +12 dB ) (s t c u d o r P e t e l o s b O 40/57 Boost/Cut ) s ( ct u d o s b O t e l o r P e STA328 Register description 6.11 Dynamics control 6.11.1 Limiter 1 attack/release threshold (addr 0x12) 6.11.2 6.11.3 6.11.4 6.11.5 D7 D6 D5 D4 D3 D2 D1 D0 L1A3 L1A2 L1A1 L1A0 L1R3 L1R2 L1R1 L1R0 0 1 1 0 1 0 1 0 Limiter 1 attack/release threshold (addr 0x13) D7 D6 D5 D4 D3 D2 D1 D0 L1AT3 L1AT2 L1AT1 L1AT0 L1RT3 L1RT2 L1RT1 L1RT0 0 1 1 0 1 0 0 Limiter 2 attack/release rate (addr 0x14) D7 D6 D5 D4 D3 L2A3 L2A2 L2A1 L2A0 L2R3 0 1 1 0 1 u d o D2 t e l o r P e L2R2 0 ) s ( ct D1 1 D0 L2R1 L2R0 1 0 Limiter 2 attack/release threshold (addr 0x15) D7 D6 D5 D4 L2AT3 L2AT2 L2AT1 L2AT0 0 1 1 ) s ( ct -O bs 0 D3 D2 D1 D0 L2RT3 L2RT2 L2RT1 L2RT0 1 0 0 1 Dynamics control description The STA328 includes 2 independent limiter blocks. The purpose of the limiters is to automatically reduce the dynamic range of a recording to prevent the outputs from clipping in anti-clipping mode, or to actively reduce the dynamic range for a better listening environment (such as a night-time listening mode, which is often needed for DVDs.) The two modes are selected via the DRC bit in configuration register D (bit 5, address 0x03). Each channel can be mapped to Limiter1, Limiter2, or not mapped. u d o r P e s b O t e l o If a channel is not mapped, that channel will clip normally when 0 dBFS is exceeded. Each limiter will look at the present value of each channel that is mapped to it, select the maximum absolute value of all these channels, perform the limiting algorithm on that value, and then if needed adjust the gain of the mapped channels in unison. The limiter attack thresholds are determined by the LxAT registers. When the attack threshold has been exceeded, the limiter, when active, will automatically start reducing the gain. The rate at which the gain is reduced when the attack threshold is exceeded is dependent upon the attack rate register setting for that limiter. The gain reduction occurs on a peak-detect algorithm. The release of limiter, when the gain is again increased, is dependent on a RMS-detect algorithm. The output of the volume/limiter block is passed through an RMS filter. The output of this filter is compared to the release threshold, determined by the Release Threshold register. When the RMS filter output falls below the release threshold, the gain is increased at a rate dependent upon the release rate register. The gain can never be increased past its set value 41/57 Register description STA328 and therefore the release will only occur if the limiter has already reduced the gain. The release threshold value can be used to set what is effectively a minimum dynamic range. This is helpful as over-limiting can reduce the dynamic range to virtually zero and cause program material to sound "lifeless". In AC mode the attack and release thresholds are set relative to full-scale. In DRC mode the attack threshold is set relative to the maximum volume setting of the channels mapped to that limiter and the release threshold is set relative to the maximum volume setting plus the attack threshold. Figure 17. Basic limiter and volume flow diagram Limiter ) s ( ct RMS u d o Gain/Volume r P e Input Gain Table 61. )- t(s dB/ms uc 3.1584 s b O 0001 od dB/ms 0.5116 2.7072 0001 0.1370 2.2560 0010 0.0744 1.8048 0011 0.0499 1.3536 0100 0.0360 0101 0.9024 0101 0.0299 0110 0.4512 0110 0.0264 0111 0.2256 0111 0.0208 1000 0.1504 1000 0.0198 1001 0.1123 1001 0.0172 1010 0.0902 1010 0.0147 1011 0.0752 1011 0.0137 1100 0.0645 1100 0.0134 1101 0.0564 1101 0.0117 1110 0.0501 1110 0.0110 1111 0.0451 1111 0.0104 e t e l 0100 Pr Fast Release rate LxR[3:0] 0000 0011 42/57 t e l o Attack rate 0000 0010 O Output Saturation Limiter attack/release rate selection LxA[3:0] o s b Attenuation Slow STA328 6.11.6 Register description Anti-clipping mode Table 62. Limiter attack/release threshold selection (AC mode) Attack threshold (AC) LxAT[3:0] Release threshold (AC) dB relative to FS LxRT[3:0] dB relative to FS 0000 -12 0000 - 0001 -10 0001 -29 dB 0010 -8 0010 -20 dB 0011 -6 0011 -16 dB 0100 -4 0100 -14 dB 0101 -2 0101 -12 dB 0110 0 0110 -10 dB 0111 +2 0111 -8 dB 1000 +3 1000 1001 +4 1001 1010 +5 1010 1011 +6 1100 +7 1101 +8 o s b r P e 1110 +9 1111 +10 let ) s ( ct -O -7 dB -6 dB ) s ( ct u d o -5 dB 1011 -4 dB 1100 -3 dB 1101 -2 dB 1110 -1 dB 1111 -0 dB u d o r P e t e l o s b O 43/57 Register description 6.11.7 STA328 Dynamic range compression mode Table 63. Limiter attack/release threshold selection (DRC mode) Attack threshold (DRC) LxAT[3:0] dB relative to volume db relative to volume + LxAT -31 0000 - 0001 -29 0001 -38 dB 0010 -27 0010 -36 dB 0011 -25 0011 -33 dB 0100 -23 0100 -31 dB 0101 -21 0101 -30 dB 0110 -19 0110 -28 dB 0111 -17 0111 -26 dB 1000 -16 1000 1001 -15 1001 1010 -14 1010 1011 -13 1100 -12 1101 -10 o s b 1110 -7 1111 -4 r P e t e l o 44/57 Release threshold (DRC) 0000 ) s ( ct -O -24 dB -22 dB -20 dB 1011 -18 dB 1100 -15 dB 1101 -12 dB 1110 -9 dB 1111 -6 dB ) s ( ct u d o r P e let u d o s b O LxRT[3:0] STA328 User programmable processing 7 User programmable processing 7.1 EQ - biquad equation The biquads use the equation that follows. This is diagrammed in Figure 18 below. Y[n] = 2(b0/2)X[n] + 2(b1/2)X[n - 1] + b2X[n - 2] - 2(a1/2)Y[n - 1] - a2Y[n - 2] = b0X[n] + b1X[n - 1] + b2X[n - 2] - a1Y[n - 1] - a2Y[n - 2] where Y[n] represents the output and X[n] represents the input. Multipliers are 28-bit signed fractional multipliers, with coefficient values in the range of 0x800000 (-1) to 0x7FFFFF (0.9999998808). ) s ( ct Coefficients stored in the user defined coefficient RAM are referenced in the following manner: " CxHy0 = b1/2 " CxHy1 = b2 " CxHy2 = -a1/2 " CxHy3 = -a2 " CxHy4 = b0/2 u d o r P e t e l o The x represents the channel and the y the biquad number. For example C3H41 is the b0/2 coefficient in the fourth biquad for channel 3 Figure 18. Biquad filter ) (s b0 /2 Z t c u -1 b1 /2 od Z -1 Pr 7.2 2 + Z -1 + -a1 /2 2 Z -1 b2 + -a2 e t e ol Pre-scale s b O 7.3 2 s b O The pre-scale block which precedes the first biquad is used for attenuation when filters are designed that boost frequencies above 0 dBFS. This is a single 28-bit signed multiplier, with 0x800000 = -1 and 0x7FFFFF = 0.9999998808. By default, all pre-scale factors are set to 0x7FFFFF. Post-scale The STA328 provides one additional multiplication after the last interpolation stage and before the distortion compensation on each channel. This is a 24-bit signed fractional multiplier. The scale factor for this multiplier is loaded into RAM using the same I2C registers as the biquad coefficients and the mix. All channels can use the same settings as channel 1 by setting the post-scale link bit. 45/57 User programmable processing 7.4 STA328 Mix/bass management The STA328 provides a post-EQ mixing block per channel. Each channel has 2 mixing coefficients, which are each 24-bit signed fractional multipliers, that correspond to the 2 channels of input to the mixing block. These coefficients are accessible via the user controlled coefficient RAM described below. The mix coefficients are expressed as 24-bit signed; fractional numbers in the range +1.0 (8388607) to -1.0 (-8388608) are used to provide three channels of output from two channels of filtered input. Figure 19. Mix/bass management block diagram Channel #1 from EQ C1MX1 High-Pass XO Filter + Channel #2 from EQ C1MX2 High-Pass XO Filter + t e l o C2MX2 s b O C3MX1 ) (s + u d o r P e C2MX1 Low-Pass XO Filter ) s ( ct Channel#1 to GC/Vol Channel#2 to GC/Vol Channel#3 to GC/Vol C3MX2 ct User-defined Mix Coefficients u d o Crossover Frequency determined by XO setting. User-defined when XO = 000 r P e After a mix is achieved, STA328 also provides the capability to implement crossover filters on all channels corresponding to 2.1 bass management solution. Channels 1 and 2 use a first-order high-pass filter and channel 3 uses a second-order low-pass filter corresponding to the setting of the XO bits of I2C register 0x0C. If XO = 000, user specified crossover filters are used. t e l o s b O 46/57 By default these coefficients correspond to pass-through. However, the user can write these coefficients in a similar way as the EQ biquads. When user-defined setting is selected, the user can only write 2nd order crossover filters. This output is then passed on to the volume/limiter block. STA328 7.5 User programmable processing Calculating 24-bit signed fractional numbers from a dB value The pre-scale, mixing, and post-scale functions of the STA328 use 24-bit signed fractional multipliers to attenuate signals. These attenuations can also invert the phase and therefore range in value from -1 to +1. It is possible to calculate the coefficient to utilize for a given negative dB value (attenuation) via the equations below. " Non-inverting phase numbers 0 to +1: " Coefficient = round(8388607 * 10(dB / 20)) " Inverting phase numbers 0 to -1: " Coefficient = 16777216 - round(8388607 * 10(dB / 20)) As can be seen by the preceding equations, the value for positive phase 0 dB is 0x7FFFFF and the value for negative phase 0 dB is 0x800000. ) s ( ct 7.6 User defined coefficient RAM 7.6.1 Coefficient address register 1 (addr 0x16) 7.6.2 D7 D6 D5 D4 D3 D2 D1 D0 CFA7 CFA6 CFA5 CFA4 CFA3 r P e CFA2 CFA1 CFA0 0 0 0 0 0 0 0 0 D7 D6 C1B23 C1B22 0 0 b O so ) (s D5 D4 D3 D2 D1 D0 C1B21 C1B20 C1B19 C1B18 C1B17 C1B16 0 0 0 0 0 0 t c u d o r Coefficient b1data register bits 15:8 (addr 0x18) P e t e l o s b O 7.6.5 let Coefficient b1data register bits 23:16 (addr 0x17) 7.6.3 7.6.4 u d o D6 D5 D4 D3 D2 D1 D0 C1B15 D7 C1B14 C1B13 C1B12 C1B11 C1B10 C1B9 C1B8 0 0 0 0 0 0 0 0 Coefficient b1data register bits 7:0 (addr 0x19) D7 D6 D5 D4 D3 D2 D1 D0 C1B7 C1B6 C1B5 C1B4 C1B3 C1B2 C1B1 C1B0 0 0 0 0 0 0 0 0 Coefficient b2 data register bits 23:16 (addr 0x1A) D7 D6 D5 D4 D3 D2 D1 D0 C2B23 C2B22 C2B21 C2B20 C2B19 C2B18 C2B17 C2B16 0 0 0 0 0 0 0 0 47/57 User programmable processing 7.6.6 Coefficient b2 data register bits 15:8 (addr 0x1B) 7.6.7 D7 D6 D5 D4 D3 D2 D1 D0 C2B15 C2B14 C2B13 C2B12 C2B11 C2B10 C2B9 C2B8 0 0 0 0 0 0 0 0 Coefficient b2 data register bits 7:0 (addr 0x1C) 7.6.8 D7 D6 D5 D4 D3 D2 D1 D0 C2B7 C2B6 C2B5 C2B4 C2B3 C2B2 C2B1 C2B0 0 0 0 0 0 0 0 0 ) s ( ct Coefficient a1 data register bits 23:16 (addr 0x1D) 7.6.9 D7 D6 D5 D4 D3 D2 C1B23 C1B22 C1B21 C1B20 C1B19 C1B18 0 0 0 0 0 0 e t e ol Coefficient a1 data register bits 15:8 (addr 0x1E) 7.6.10 D7 D6 D5 C3B15 C3B14 C3B13 0 0 0 7.6.11 D7 D6 C3B7 C3B6 7.6.12 7.6.13 s b O o r P 0 D0 C1B16 0 D3 D2 D1 D0 C3B11 C3B10 C3B9 C3B8 0 0 0 0 0 du ct o r P 0 D5 D4 D3 D2 D1 D0 C3B5 C3B4 C3B3 C3B2 C3B1 C3B0 0 0 0 0 0 0 Coefficient a2 data register bits 23:16 (addr 0x20) e t e ol s b O ) (s D4 C3B12 du D1 C1B17 Coefficient a1 data register bits 7:0 (addr 0x1F) 0 48/57 STA328 D7 D6 D5 D4 D3 D2 D1 D0 C4B23 C4B22 C4B21 C4B20 C4B19 C4B18 C4B17 C4B16 0 0 0 0 0 0 0 0 Coefficient a2 data register bits 15:8 (addr 0x21) D7 D6 D5 D4 D3 D2 D1 D0 C4B15 C4B14 C4B13 C4B12 C4B11 C4B10 C4B9 C4B8 0 0 0 0 0 0 0 0 Coefficient a2 data register bits 7:0 (addr 0x22) D7 D6 D5 D4 D3 D2 D1 D0 C4B7 C4B6 C4B5 C4B4 C4B3 C4B2 C4B1 C4B0 0 0 0 0 0 0 0 0 STA328 7.6.14 7.6.15 7.6.16 7.6.17 User programmable processing Coefficient b0 data register bits 23:16 (addr 0x23) D7 D6 D5 D4 D3 D2 D1 D0 C5B23 C5B22 C5B21 C5B20 C5B19 C5B18 C5B17 C5B16 0 0 0 0 0 0 0 0 Coefficient b0 data register bits 15:8 (addr 0x24) D7 D6 D5 D4 D3 D2 D1 D0 C5B15 C5B14 C5B13 C5B12 C5B11 C5B10 C5B9 C5B8 0 0 0 0 0 0 0 0 ) s ( ct Coefficient b0 data register bits 7:0 (addr 0x25) D7 D6 D5 D4 D3 D2 C5B7 C5B6 C5B5 C5B4 C5B3 C5B2 0 0 0 0 0 0 e t e ol Coefficient write control register (addr 0x26) D7 D6 D5 D4 Reserved Reserved Reserved Reserved 0 0 0 0 s b O o r P du D1 C5B1 0 D0 C5B0 0 D3 D2 D1 D0 RA R1 WA W1 0 0 0 0 Coefficients for EQ, mix and scaling are handled internally in the STA328 via RAM. Access to this RAM is available to the user via an I2C register interface. A collection of I2C registers are dedicated to this function. First register contains the coefficient base address, five sets of three registers store the values of the 24-bit coefficients to be written or that were read, and one contains bits used to control the read or write of the coefficient (s) to RAM. The following are instructions for reading and writing coefficients. ) (s t c u d o r P e t e l o s b O 49/57 User programmable processing 7.7 Reading a coefficient from RAM 7.8 " write 8 bits of address to I2C register 0x16 " write 1 to bit R1 (D2) of I2C register 0x26 " read top 8 bits of coefficient in I2C address 0x17 " read middle 8 bits of coefficient in I2C address 0x18 " read bottom 8 bits of coefficient in I2C address 0x19 Reading a set of coefficients from RAM " write 8 bits of address to I2C register 0x16 " write 1 to bit RA (D3) of I2C register 0x26 " read top 8 bits of coefficient in I2C address 0x17 " read middle 8 bits of coefficient in I2C address 0x18 " read bottom 8 bits of coefficient in I2C address 0x19 " read top 8 bits of coefficient b2 in I2C address 0x1A " read middle 8 bits of coefficient b2 in I2C address 0x1B " read bottom 8 bits of coefficient b2 in I2C address 0x1C " read top 8 bits of coefficient a1 in I2C address 0x1D " read middle 8 bits of coefficient a1 in I2C address 0x1E " read bottom 8 bits of coefficient a1 in I2C address 0x1F " read top 8 bits of coefficient a2 in I2C address 0x20 " read middle 8 bits of coefficient a2 in I2C address 0x21 " read bottom 8 bits of coefficient a2 in I2C address 0x22 " read top 8 bits of coefficient b0 in I2C address 0x23 " read middle 8 bits of coefficient b0 in I2C address 0x24 " read bottom 8 bits of coefficient b0 in I2C address 0x25 s b O ) s ( ct ) (s s b O t c u d o r P e " write 8 bits of address to I2C register 0x16 " write top 8 bits of coefficient in I2C address 0x17 " write middle 8 bits of coefficient in I2C address 0x18 " write bottom 8 bits of coefficient in I2C address 0x19 " write 1 to W1 bit in I2C address 0x26 u d o r P e t e l o Writing a single coefficient to RAM t e ol 7.9 50/57 STA328 STA328 7.10 User programmable processing Writing a set of coefficients to RAM " write 8 bits of starting address to I2C register 0x16 " write top 8 bits of coefficient b1 in I2C address 0x17 " write middle 8 bits of coefficient b1 in I2C address 0x18 " write bottom 8 bits of coefficient b1 in I2C address 0x19 " write top 8 bits of coefficient b2 in I2C address 0x1A " write middle 8 bits of coefficient b2 in I2C address 0x1B " write bottom 8 bits of coefficient b2 in I2C address 0x1C " write top 8 bits of coefficient a1 in I2C address 0x1D " write middle 8 bits of coefficient a1 in I2C address 0x1E " write bottom 8 bits of coefficient a1 in I2C address 0x1F " write top 8 bits of coefficient a2 in I2C address 0x20 " write middle 8 bits of coefficient a2 in I2C address 0x21 " write bottom 8 bits of coefficient a2 in I2C address 0x22 " write top 8 bits of coefficient b0 in I2C address 0x23 " write middle 8 bits of coefficient b0 in I2C address 0x24 " write bottom 8 bits of coefficient b0 in I2C address 0x25 " write 1 to WA bit in I2C address 0x26 ) s ( ct u d o r P e t e l o s b O The mechanism for writing a set of coefficients to RAM provides a method of updating the five coefficients corresponding to a given biquad (filter) simultaneously to avoid possible unpleasant acoustic side-effects. When using this technique, the 8-bit address would specify the address of the biquad b1 coefficient (for example 0, 5, 10, 15, ..., 45 decimal), and the STA328 will generate the RAM addresses as offsets from this base value to write the complete set of coefficient data. ) (s d o r Table 64. RAM block for biquads, mixing, and scaling Index (decimal) 0 P e t e l o 1 s b O t c u Index (Hex) Coefficient Default 0x00 C1H10 (b1/2) 0x000000 0x01 C1H11 (b2) 0x000000 C1H12 (a1/2) 0x000000 2 0x02 Channel 1 - Biquad 1 3 0x03 C1H13 (a2) 0x000000 4 0x04 C1H14 (b0/2) 0x400000 5 0x05 Channel 1 - Biquad 2 C1H20 0x000000 ... ... ... ... ... 19 0x13 Channel 1 - Biquad 4 C1H44 0x400000 20 0x14 C2H10 0x000000 C2H11 0x000000 Channel 2 - Biquad 1 21 0x15 ... ... ... ... ... 39 0x27 Channel 2 - Biquad 4 C2H44 0x400000 51/57 User programmable processing Table 64. RAM block for biquads, mixing, and scaling (continued) Index (decimal) Index (Hex) 40 0x28 41 0x29 42 0x2A 43 C12H1 (b2) 0x000000 C12H2 (a1/2) 0x000000 0x2B C12H3 (a2) 0x000000 44 0x2C C12H4 (b0/2) 0x400000 45 0x2D C12L0 (b1/2) 0x000000 46 0x2E C12L1 (b2) 0x000000 47 0x2F 48 0x30 C12L3 (a2) 49 0x31 C12L4 (b0/2) 50 0x32 Channel 1 - Pre-scale 51 0x33 Channel 2 - Pre-scale 52 0x34 Channel 1 - Post-scale 53 0x35 Channel 2 - Post-scale 54 High-pass 2nd order filter for XO = 000 Low-pass 2nd order filter for XO = 000 ) s ( ct C12L2 (a1/2) ro du C1PreS P e 0x000000 0x000000 0x400000 0x7FFFFF C2PreS 0x7FFFFF 0x7FFFFF C2PstS 0x7FFFFF 0x36 t e l o C1PstS Channel 3 - Post-scale C3PstS 0x7FFFFF 55 0x37 Thermal warning - Post scale TWPstS 0x5A9DF7 56 0x38 Channel 1 - Mix 1 C1MX1 0x7FFFFF 57 0x39 Channel 1 - Mix 2 C1MX2 0x000000 58 0x3A Channel 2 - Mix 1 C2MX1 0x000000 Channel 2 - Mix 2 C2MX2 0x7FFFFF 0x3C Channel 3 - Mix 1 C3MX1 0x400000 0x3D Channel 3 - Mix 2 C3MX2 0x400000 0x3E Unused 0x3F Unused ro P e let 62 63 bs O ) t(s c u d 0x3B 61 52/57 Default 0x000000 60 O Coefficient C12H0 (b1/2) 59 o s b STA328 STA328 7.11 User programmable processing Variable max power correction (addr 0x27, 0x28) D7 D6 D5 D4 D3 D2 D1 D0 MPCC15 MPCC14 MPCC13 MPCC12 MPCC11 MPCC10 MPCC9 MPCC8 0 0 1 0 1 1 0 1 MPCC7 MPCC6 MPCC5 MPCC4 MPCC3 MPCC2 MPCC1 MPCC0 1 1 0 0 0 0 0 0 MPCC bits determine the 16 MSBs of the MPC compensation coefficient. This coefficient is used in place of the default coefficient when MPCV = 1. 7.12 Fault detect recovery (addr 0x2B, 0x2C) D7 D6 D5 D4 D3 D2 D1 FRDC15 FDRC14 FDRC13 FDRC12 FDRC11 FDRC10 FDRC9 0 0 0 0 0 0 FDRC7 FDRC6 FDRC5 FDRC4 FDRC3 FDRC2 0 0 0 0 1 1 e t e ol Pr u d o ) s ( ct 0 D0 FDRC8 0 FDRC1 FDRC0 0 0 FDRC bits specify the 16-bit fault detect recovery time delay. When FAULT is asserted, the output TRISTATE will be immediately asserted low and held low for the time period specified by this constant. A constant value of 0x0001 in this register is approximately 0.083 ms. The default value of 0x000C specifies approximately 1 ms. ) (s s b O t c u d o r P e t e l o s b O 53/57 Package mechanical data 8 STA328 Package mechanical data Figure 20. PowerSO-36 slug up outline drawing ) s ( ct u d o r P e t e l o ) (s t c u d o r P e t e l o s b O 54/57 s b O STA328 Package mechanical data Table 65. PowerSO-36 slug up dimensions mm inch Symbol Min Min Typ Max 3.25 - 3.43 0.128 - 0.135 A2 3.10 - 3.20 0.122 - 0.126 A4 0.80 - 1.00 0.031 - 0.039 A5 - 0.20 - - 0.008 - a1 0.03 - -0.04 0.001 - -0.002 b 0.22 - 0.38 0.009 - 0.015 c 0.23 - 0.32 0.009 - D 15.80 - 16.00 0.622 - D1 9.40 - 9.80 0.370 - D2 - 1.00 - - E 13.90 - 14.50 0.547 E1 10.90 - 11.10 0.429 E2 - - 2.90 E3 5.80 - 6.20 E4 2.90 - e - 0.65 e3 - -O G 0 H 15.50 e t e l ) s ( ct 0.013 u d o Pr 0.630 0.386 0.039 - - 0.571 - 0.437 - - 0.114 0.228 - 0.244 0.114 - 0.126 - - 0.026 - - - 0.435 - - 0.08 0 - 0.003 - 15.90 0.610 - 0.626 - 1.10 - - 0.043 0.80 - 1.10 0.031 - 0.043 M 2.25 - 2.60 0.089 - 0.102 N - - 10 degrees - - 10 degrees R - 0.6 - - 0.024 - s - - 8 degrees - - 8 degrees L b O Max A h e t e l so Typ u d o Pr - ) s ( ct 11.05 3.20 o s b In order to meet environmental requirements, ST offers these devices in ECOPACK(R) packages. These packages have a Lead-free second level interconnect. The category of second Level Interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label. ECOPACK is an ST trademark. ECOPACK specifications are available at: www.st.com. 55/57 Revision history 9 STA328 Revision history Table 66. Document revision history Date Revision Sep-2004 1 Initial release Jul-2005 2 Added pins 7 and 25 in block diagram May-2006 3 Changed from product preview to maturity 4 Updated device pin 1 labeling and connections Updated applications schematic Figure 5 on page 7 Added characterization curves in Chapter 4 on page 14 Updated device address in Section 5.2 on page 16 Updated configuration registers in Table 9: Register summary on page 19 Updated configuration registers from Section 6.1 on page 20 to Section 6.5 Updated PowerSO-36 Package mechanical data on page 54 13-May-2008 Changes ) s ( ct u d o r P e t e l o ) (s t c u d o r P e t e l o s b O 56/57 s b O STA328 ) s ( ct Please Read Carefully: u d o Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries ("ST") reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. r P e All ST products are sold pursuant to ST's terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. t e l o No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. ) (s s b O UNLESS OTHERWISE SET FORTH IN ST'S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. t c u UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER'S OWN RISK. d o r P e t e l o Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. s b O ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. (c) 2008 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 57/57