RF Vector Signal Generators
TSG4100A Series
The TSG4100A Series RF Vector Signal Generator offers mid-range
performance and up to 200 MHz modulation bandwidth at an entry-level RF
signal generator price. They use a new technique to provide spurious free
outputs with low phase noise (-113 dBc/Hz at 20 kHz offset from 1 GHz
carrier) and extraordinary frequency resolution (1 μHz at any frequency).
The TSG4100A Series comes standard with analog modulation.
Convenient, in-field software upgrades allow for easy transition from analog
to more advanced vector and digital modulation capabilities, providing the
most flexible configuration and best CAPEX protection. These instruments
complement other leading mid-range RF test solutions from Tektronix, such
as the USB-based RSA306 Spectrum Analyzer and MDO4000B and
MDO3000 Mixed Domain Oscilloscopes.
The TSG4100A Series instruments use an ovenized SC-cut oscillator
(TSG410xA-M00 or E1 models) time-base, providing a 100 X improvement
in stability (and a 100 X reduction in the in-close phase noise) compared to
instruments that use a TCXO time-base.
Key features
Analog and vector/digital signal generation capabilities
Dual baseband ARB generators
Analog modulation standard
Soft key upgrade to vector/digital modulation at very low cost
Digital modulation applications for GSM, EDGE, W-CDMA, APCO-25,
DECT, NADC, PDC, and TETRA
USB, GPIB, RS-232, and LAN interfaces
12 pounds (5.6 kg)
2U high and half standard rack width
Key performance specifications
True DC to 2 GHz, 4 GHz or 6 GHz to support both analog and vector/
digital signal generation
Typical ≤±0.30 dB amplitude accuracy (0 dBm CW signal at 22 ºC)
from 10 MHz to 6 GHz
I/Q modulation inputs (400 MHz RF bandwidth)
ASK, FSK, MSK, PSK, QAM, VSB, and custom I/Q
Analog modulation
The Tektronix TSG4100A Series RF Vector Signal Generators offer a wide
variety of modulation capabilities. Modes include amplitude modulation
(AM), frequency modulation (FM), phase modulation (ΦM), and pulse
modulation. There is an internal modulation source as well as an external
modulation input. The internal modulation source produces sine, ramp,
saw, square, and noise waveforms. An external modulation signal may be
applied to the rear panel modulation input. The internal modulation
generator is available as an output on the rear panel.
Vector modulation
The TSG4100A Series builds on this performance by adding full support for
vector signal modulation on RF carriers between 400 MHz and 6.0 GHz. It
features a dual arbitrary waveform generator operating at 125 MHz for
baseband signal generation. The generator has built-in support for the most
common vector modulation schemes: ASK, QPSK, DQPSK, π/4 DQPSK,
8PSK, FSK, CPM, QAM (4 to 256), 8VSB, and 16VSB. It also includes
built-in support for all the standard pulse shaping filters used in digital
communications: raised cosine, root-raised cosine, Gaussian, rectangular,
triangular, and more. Lastly, it provides direct support for the controlled
injection of additive white Gaussian noise (AWGN) into the signal path.
www.tektronix.com 1
Internal baseband generators
Using a novel architecture for I/Q modulation, the TSG4100A Series
provides quick, user-friendly waveform generation. The baseband
generator supports the playback of pure digital data. It automatically maps
digital symbols into a selected I/Q constellation at symbol rates of up to
6 MHz and passes the result through the selected pulse shaping filter to
generate a final waveform updated in real time at 125 MHz. This baseband
signal is then modulated onto an RF carrier using standard IQ modulation
techniques.
Digital communications protocols (GSM, GSM EDGE, W-CDMA, APCO-25,
DECT, NADC, PDC, and TETRA) quickly configure the signal generator to
the correct modulation type, symbol data rates, TDMA duty cycles, and
digital waveform filters. The preset protocols also configure the rear-panel
TDMA, START of FRAME, and SYMBOL CLOCK digital outputs. The
baseband generators can be configured for these protocols without the use
of external computers or third party software.
The I/Q waveforms are computed in real time. Symbols are mapped to
constellations, digitally filtered, and up-sampled to 125 Msps to drive the I/
Q modulator via dual 14-bit DACs. The symbols can be a fixed pattern,
PRBS data from an internal source, or come from a downloaded user list of
up to 16 Mbits.
The constellation mapping can be modified by the user. Digital filters
include raised cosine, root raised cosine, Gaussian, rectangular, linear,
sinc, and user-defined FIR.
External IQ modulation
The rear-panel BNC I/Q modulation inputs and outputs enable arbitrary
vector modulation via an external source. The external signal path supports
maximally 400 MHz of RF bandwidth with a full scale range of ±0.5 V and a
50 Ω input impedance.
Power vs. frequency
All TSG4100A Series models have cascaded stages of amplifiers and
digital attenuators to drive the RF output. Five stages can provide up to
+25 dB of gain to -130 dB of attenuation in 156 digitally controlled steps.
During factory calibration, the output power is measured at 32 frequencies
per octave for each of the 156 attenuator steps to populate a memory
matrix with about 40,000 elements. When set to a particular frequency and
power, the instrument interpolates between these matrix elements to
determine the best attenuator setting. An analog attenuator is used to
provide 0.01 dB resolution between matrix elements and to compensate for
residual thermal effects.
OCXO time-base
These instruments offer an oven-controlled crystal oscillator (OCXO) time-
base. The time-base uses a third-overtone stress-compensated 10 MHz
resonator in a thermostatically controlled oven. The time-base provides
very low phase noise and very low aging.
Easy remote communications
Remote operation is supported with RS-232, LAN, and GPIB interfaces. All
instrument functions can be controlled and read over any of the interfaces.
Up to nine instrument configurations can be saved in non-volatile memory.
TSG4100A Series RF Vector Signal Generator
2 www.tektronix.com
Specifications
All specifications apply to all models unless noted otherwise.
Frequency
BNC output, all models DC to 62.5 MHz
N-type outputs
TSG4102A 950 kHz to 2.0 GHz
TSG4104A 950 kHz to 4.0 GHz
TSG4106A 950 kHz to 6.0 GHz
Frequency resolution 1 μHz at any frequency
Switching speed <8 ms (to within 1 ppm)
Frequency error <(10–18 + time-base error) × fc
Frequency stability 1 × 10–11 (1 s Allan variance)
Front panel BNC output
Frequency range DC to 62.5 MHz
Amplitude 1.00 VRMS to 0.001 VRMS (-47 dBm to +14.96 dBm)
Offset ±1.5 VDC
Offset resolution 5 mV
Maximum excursion 1.817 V (amplitude + offset)
Amplitude resolution <1 %
Amplitude accuracy ±0.7 dB
Harmonics, typical <–40 dBc
Spurious, typical <–65 dBc
Output coupling DC, 50 Ω ±2%
Impedance 50 Ω
Reverse protection ±5 VDC
VSWR, typical < 1.6 :1
Datasheet
www.tektronix.com 3
Front panel N-type output
Power output
TSG4102A +16.5 dBm to –110 dBm
TSG4104A +16.5 dBm to –110 dBm (<3 GHz)
TSG4106A +16.5 dBm to –110 dBm (<4 GHz)
+10 dBm to –110 dBm (4-6 GHz)
Voltage output
TSG4102A 1.5 VRMS to 0.7VRMS
TSG4104A 1.5 VRMS to 0.7 μVRMS (<3 GHz)
TSG4106A 1.5 VRMS to 0.7 μVRMS (<4 GHz)
Amplitude resolution 0.01 dBm
Amplitude accuracy
CW, 50 Ω load (dB, typical) CW, 18 °C to 28 °C >10 dBm 10 to -30 dBm -30 to -60 dBm -60 to -100 dBm <-100 dBm
10 MHz to 0.1 GHz ±0.2 ±0.25 ±0.35 ±0.45 ±0.6
0.1 GHz to 2 GHz ±0.15 ±0.15 ±0.25 ±0.35 ±0.6
2 GHz to 4 GHz ±0.3 ±0.2 ±0.35 ±0.6 ±0.8
4 GHz to 6 GHz NA ±0.3 ±0.4 ±0.75 ±1.25
CW, 50 Ω load (dB, max) Level range: +5 to -30 dBm (max) +5 to -30 dBm (typical)
Temperature: 18 °C to 28 °C 5 °C to 40 °C 5 °C to 40 °C
10 MHz to 0.1 GHz ±0.6 ±1.0 ±0.7
0.1 GHz to 2 GHz ±0.6 ±1.0 ±0.6
2 GHz to 4 GHz ±0.6 ±1.0 ±0.7
4 GHz to 6 GHz ±1 ±1.5 ±0.9
Impedance 50 Ω
Output coupling AC, 50 Ω
VSWR, typical <1.5 (2 MHz to 2 GHz)
<1.8 (2 GHz to 6 GHz)
Reverse protection 30 VDC, +25 dBm
IQ modulation output level
accuracy
Output amplitude is -5 dBm.
Temperature: 18 °C to 28 °C 5 °C to 40 °C
Fc: Typical (dB) Max (dB) Typical (dB)
<2 GHz ±0.1 ±0.4 ±0.4
2 GHz to 4 GHz ±0.2 ±0.6 ±0.4
4 GHz to 6 GHz ±0.4 ±0.8 ±0.7
TSG4100A Series RF Vector Signal Generator
4 www.tektronix.com
Spectral purity of the RF output
Subharmonics None
Harmonics, maximum Output level <0 dBm, 1 GHz CW signal
TSG4102A and TSG4104A < -38 dBc
TSG4106A < -30 dBc
Harmonics, typical (output level <
0 dBm)
< -35 dBc, CW , Fc < 2 GHz
Spurious (typical) Output level -10 dBm, CW
< -68 dBc >10 kHz from carrier in 950 kHz to 1 GHz
< -60 dBc >10 kHz from carrier in 1 GHz to 2 GHz
< -55 dBc >10 kHz from carrier in 2 GHz to 4 GHz
< -55 dBc >10 kHz from carrier in 4 GHz to 6 GHz
Residual FM, typical 1 Hz rms (300 Hz to 3 kHz bandwidth)
Residual AM, typical 0.006 % rms (300 Hz to 3 kHz bandwidth)
SSB phase noise Output level is +5 dBm at 18 °C to 28 °C.
Carrier Offset from carrier, typical (dBc/Hz)
1 kHz 10 kHz 20 kHz 1 MHz
1 GHz -102 -110 -113 -124
2 GHz -96 -104 -107 -118
3 GHz -93 -102 -105 -120
6 GHz -87 -96 -99 -114
SSB phase noise at 1 GHz carrier,
maximum (output level +5 dBm,
5 ℃ to 40 ℃)
1 kHz offset –95 dBc/Hz
10 kHz offset –106 dBc/Hz
20 kHz offset –107 dBc/Hz
1 MHz offset –120 dBc/Hz
2 GHz offset –118 dBc/Hz
>3 GHz offset –120 dBc/Hz
Datasheet
www.tektronix.com 5
Phase setting (front panel outputs)
Maximum phase step ±360º
Phase resolution 0.01º (DC to 100 MHz)
0.1º (100 MHz to 1 GHz)
1.0º (1 GHz to 6 GHz)
OCXO time-base (Option M00 or Option E1)
Oscillator type Oven-controlled, 3rd OT, SC-cut crystal
Initial accuracy at calibration
(20 minute warm-up, at 18 ºC to
28 ºC)
<±0.02 ppm
Temperature drift (0 ºC to 40 ºC) <±0.003 ppm
Aging <±0.05 ppm/year
TSG4100A Series RF Vector Signal Generator
Spectral purity of the RF output
6 www.tektronix.com
VCXO time base (Option M01)
Initial accuracy at calibration
(20 minute warm-up, at 18 ºC to
28 ºC)
<±0.5 ppm
Temperature drift (0 ºC to 40 ºC) <±5.0 ppm
Aging <±3.0 ppm/year
Time-base input
Frequency 10 MHz, ±2 ppm
Amplitude 0.5 VP-P to 4 VP-P (–2 dBm to +16 dBm)
Input impedance 50 Ω, AC coupled
Time-base output
Frequency 10 MHz, sine
Source 50 Ω, DC transformer coupled
Amplitude >7.5 dBm
Internal modulation source
Waveforms Sine, ramp, saw, square, pulse, noise
Sine THD –74 dBc (typical at 20 kHz)
Ramp linearity <0.05 % (1 kHz)
Rate
TSG4102A and TSG4104A 1 μHz to 500 kHz: < 62.5 MHz CF
1 μHz to 50 kHz: ≥62.5 MHz
TSG4106A 1 μHz to 500 kHz: < 93.75 MHz CF
1 μHz to 50 kHz: ≥93.75 MHz
Rate resolution 1 μHz
Rate error 1:231 + time-base error
Noise function White Gaussian noise (rms = dev / 5)
Noise bandwidth 1 μHz < ENBW < 50 kHz
Pulse generator period 1 μs to 10 s
Pulse generator width 100 ns to 9999.9999 ms
Pulse timing resolution 5 ns
Pulse noise function Length 2N-1 PRBS 5 ≤ N ≤ 32, bit period 100 nS to 10 S
Datasheet
www.tektronix.com 7
Analog modulation output
Connector type BNC (rear panel)
Impedance 50 Ω
Function AM, FM, ΦM, Pulse
Scale factor ±1 V for ± full deviation
Pulse/Blank Low = 0 V
Hi = 3.3 V
External analog modulation input
Connector type BNC (rear panel)
Impedance 100 kΩ
Function AM, FM, ΦM, Pulse
Scale factor ±1 V for ± full deviation
Pulse/Blank Low = 0 V
Hi = 3.3 V
Input coupling DC or 4 Hz High-pass
Pulse Threshold +1 VDC
Input Offset < 500 μV
Amplitude modulation
Range 0 to 100% (decreases above +7 dBm)
Resolution 0.1%
Modulation source Internal or external
Modulation distortion, typical
BNC output <1 % (fc < 62.5 MHz, fm = 1 kHz)
N-type output <3 % (fc > 62.5 MHz, fm = 1 kHz)
Modulation bandwidth (external) >100 kHz
TSG4100A Series RF Vector Signal Generator
8 www.tektronix.com
Frequency modulation
Minimum frequency deviation 0.01 Hz
Maximum frequency deviation
TSG4102A and TSG4104A Smaller of fc and 64 MHz – In 0 to 62.5 MHz
Frequency range Maximum deviation
62.5 MHz < fc ≤ 126.5625 MHz 1 MHz
126.5625 MHz < fc ≤253.1250 MHz 2 MHz
253.1250 MHz < fc ≤ 506.25 MHz 4 MHz
506.25 MHz < fc ≤ 1.0125 GHz 8 MHz
1.0125 GHz < fc ≤ 2.0 GHz 16 MHz
2.025 GHz < fc ≤ 4.0 GHz (TSG4104A) 32 MHz
TSG4106A Smaller of fc and 96 MHz – In 0 to 93.75 MHz
Frequency range Maximum deviation
93.75 MHz < fc ≤ 189.84375 MHz 1 MHz
189.84375 MHz < fc ≤ 379.6875 MHz 2 MHz
379.6875 MHz< fc ≤ 759.375 MHz 4 MHz
759.375 MHz < fc ≤ 1.51875 GHz 8 MHz
1.51875 GHz < fc ≤ 3.0375 GHz 16 MHz
3.0375 GHz < fc ≤ 6.0 GHz 32 MHz
Deviation resolution 0.1 Hz
Deviation accuracy, typical
TSG4102A and TSG4104A < 0.1% of selected deviation + 5 Hz (fc < 62.5 MHz)
< 2% of selected deviation + 20 Hz (fc > 62.5 MHz)
TSG4106A < 0.1% of selected deviation + 5 Hz (fc < 93.75 MHz)
< 2% of selected deviation + 20 Hz (fc > 93.75 MHz)
Modulation source Internal or external
Modulation distortion, typical < -60 dB (fc=100 MHz, fm=1 KHz, fd= 3 KHz)
External FM carrier offset, typical < ±0.001 X FM deviation
Modulation bandwidth, typical
TSG4102A and TSG4104A 500 kHz (fc < 62.5 MHz)
100 kHz (fc > 62.5 MHz)
TSG4106A 500 kHz (fc < 93.75 MHz)
100 kHz (fc > 93.75 MHz)
Datasheet
www.tektronix.com 9
Phase modulation
Deviation 0º to 360º
Deviation resolution, typical 0.01º (DC to 100 MHz)
0.1º (100 MHz to 1 GHz)
1º (1 GHz and above)
Deviation accuracy, typical
TSG4102A and TSG4104A 2% (fc < 62.5 MHz)
3% (fc > 62.5 MHz)
TSG4106A 2% (fc < 93.75 MHz)
3% (fc > 93.75 MHz)
Modulation source Internal or external
Modulation distortion, typical < -60 dB (fc = 100 MHz, fm =1 kHz, ΦD = 50º)
Modulation bandwidth, typical
TSG4102A and TSG4104A 500 kHz (fc < 62.5 MHz)
100 kHz (fc > 62.5 MHz)
TSG4106A 500 kHz (fc < 93.75 MHz)
100 kHz (fc > 93.75 MHz)
Pulse modulation
Pulse mode Logic High turns RF output ON
On-Off ratio, typical
BNC output > 70 dB
Type-N output > 57 dB (fc < 1.0 GHz)
> 40 dB (1.0 GHz ≤ fc < 4.0 GHz)
> 35 dB (4.0 GHz ≤ fc < 6.0 GHz)
Pulse feed-through, typical 10% of carrier for 20 ns at turn on
Turn On-Off delay 60 ns
RF Rise-Fall time, typical 20 ns
Modulation source Internal or external pulse
TSG4100A Series RF Vector Signal Generator
10 www.tektronix.com
Interface connectors
USB USB 2.0, host
Ethernet (LAN) 10/100 Base-T.TCP/IP and DHCP default
GPIB IEEE488.2
RS-232 4800 to 115,200 baud, RTS/CTS flow
External I/Q modulation (Option EIQ)
Carrier frequency range 400 MHz to 2.0 GHz (TSG4102A)
400 MHz to 4.0 GHz (TSG4104A)
400 MHz to 6.0 GHz (TSG4106A)
I/Q inputs (rear panel) 50 Ω, ±0.5 V
I/Q full scale input (I2 + Q2)1/2 = 0.5 V
Modulation bandwidth max 400 MHz RF bandwidth
I or Q input offset <500 μV
Carrier suppression > -45 dBc for fc ≤ 3 GHz
> -40 dBc for 3 GHz < fc ≤ 5 GHz
> -35 dBc for fc > 5 GHz
I and Q baseband modulation
bandwidth (3 dB from fc)
> 200 MHz (fc < 2.5 GHz, RF BW >400 MHz)
> 150 MHz (fc > 2.5 GHz, RF BW >300 MHz)
Dual baseband generator (Option VM00)
Channels 2 (I and Q)
DAC data format Dual 14-bit at 125 MS/s
Reconstruction filter 10 MHz, 3rd order Bessel LPF
Arbitrary symbol memory Up to 16 Mbits
Symbol rate 1 Hz to 6 MHz (1 μHz resolution)
Symbol length 1 to 9 bits (maps to constellation)
Symbol mapping Default or user-defined constellation
Symbol source (User-defined
symbols, built-in PRBS generator,
or settable pattern generator)
PRBS length 2n – 1 (5 < n < 32; 31 to about 4.3 × 109 symbols)
Pattern generator 16 bits
Datasheet
www.tektronix.com 11
Digital filtering
Filter type Raised Cosine, Root Raised Cosine, Gaussian, Rectangular, Linear, Sinc, linearized Gaussian, C4FM, customized FIR
Filter length 24 symbols
Noise impairments
Additive noise White, Gaussian
Level –70 dBc to –10 dBc
Basic vector modulation formats (Option VM00)
Formats by bit Constellation 1-bit 2-bit 3-bit 4-bit 5-bit 6-bit 8-bit
ASK 2ASK 4ASK 8ASK 16ASK
FSK BFSK 4FSK 8FSK 16FSK
PSK BPSK QPSK 8PSK 16PSK
QAM n/a 4QAM n/a 16QAM 32QAM 64QAM 256QAM
CPM BCPM 4CPM 8CPM 16CPM
VSB n/a n/a 8VSB 16VSB
Others OQPSK, DQPSK, π/4DQPSK, 3π/8 8 PSK
TSG4100A Series RF Vector Signal Generator
Dual baseband generator (Option VM00)
12 www.tektronix.com
Digital modulation applications (typical)
Digital modulation applications
options
Option Application
VM01 GSM
VM02 GSM-EDGE
VM03 W-CDMA
VM04 APCO-25 Phase 1
VM05 DECT
VM06 NADC
VM07 PDC
VM08 TETRA
VM10 Audio clip (analog AM and FM)
Option VM01 GSM, (GMSK, 270.833 kS/s, 935 MHz, 0 dBm), RMS EVM: 0.6%
Option VM02 GSM-EDGE, (3π/8 8PSK, 270.833 kS/s, 935 MHz, 0 dBm), RMS EVM: 0.30%
Datasheet
www.tektronix.com 13
Option VM03 W-CDMA, (QPSK,3.840Mcps, 2.1425GHz, 0dBm), RMS EVM: 1.7%
TSG4100A Series RF Vector Signal Generator
Digital modulation applications (typical)
14 www.tektronix.com
Option VM03 W-CDMA (QPSK,3.840Mcps, 1.85 GHz, 0dBm), RMS EVM: 1.7%
Option VM04 APCO-25, (4FSK-C4FM, 4.8 kS/s,850 MHz, 0 dBm), Freq Err: 0.5%
Datasheet
Digital modulation applications (typical)
www.tektronix.com 15
Option VM05 DECT, (2FSK 1.152 Mbps,1.925 GHz, 0 dBm), RMS FSK Err: 1.5%
Option VM06 NADC, (π/4 DQPSK, 24.3 kS/s, 875 MHz, 0 dBm), RMS EVM: 0.3%
TSG4100A Series RF Vector Signal Generator
Digital modulation applications (typical)
16 www.tektronix.com
Option VM07 PDC, (π/4 DQPSK, 21 kS/s, 800 MHz, 0 dBm), RMS EVM: 0.6%
Option VM08 TETRA, (π/4 DQPSK,18 kS/s, 420 MHz, 0 dBm), RMS EVM: 0.7%
Datasheet
Digital modulation applications (typical)
www.tektronix.com 17
32QAM, (6 MS/s, 5.8 GHz, Root raised cosine filter, 0 dBm), RMS EVM: 1.6%
256QAM, (6 MS/s, 2.45 GHz, Root raised cosine filter, 0 dBm), RMS EVM: 1.1%
TSG4100A-ATT Option
Nominal impedance 50 Ω
Nominal attenuation 30 dB
Frequency range DC to 6 GHz
Attenuation deviation ±0.75 dB (DC to 6 GHz)
Maximum VSWR 1.15 (DC to 4 GHz)
1.2 (4 GHz to 6 GHz)
Power rating 5 Watt average power up to 25 ˚C ambient temperature, linearly derated to 1 Watt at 125 ˚C ambient temperature.
Weight 0.052 kg
TSG4100A Series RF Vector Signal Generator
Digital modulation applications (typical)
18 www.tektronix.com
Operating temperature -65 °C to 125 °C
Compliance 2011/65/EU (RoHS) compliant
Rear-panel markers
Type Symbol Clock, Data Frame, TDMA, and user-defined
Amplitude 0.5 to 4 Vpp (–2 dBm to +16 dBm)
Output impedance 50 Ω, AC coupled
Physical characteristics
Dimensions
Height 114 mm (4.5 in)
Width 216 mm (8.5 in)
Depth 347 mm (13.7 in)
Weight 5.4 kg (12 lbs)
Operating characteristics
Temperature
Operating +5 °C to +40 °C
Non-operating -20 °C to +60 °C
Humidity Operating Non-operating
5% to 95% relative humidity (%RH) at up to +30 °C 5% to 95% RH (Relative Humidity) at up to +30 °C
5% to 45% RH above +30 °C up to +40 °C, non-condensing 5% to 45% RH above +30 °C up to +40 °C, non-condensing
Altitude
Operating Up to 3,000 m
Non-operating Up to 12,000 m
Line power <90 W, 90 to 264 VAC, 47 to 63 Hz with PFC
Vibration and shock
Random vibration Operating Non-operating
0.27 GRMS, 5 500 Hz, 10 minutes per axis, 3 axes (30 minutes
total for Option M01)
2.28 GRMS, 5 500 Hz, 10 minutes per axis, 3 axes (30 minutes
total for Option M01)
0.22 GRMS, 5 500 Hz, 10 minutes per axis, 3 axes (30 minutes
total for Options M00 or E1)
2.13 GRMS, 5 500 Hz, 10 minutes per axis, 3 axes (30 minutes
total for Options M00 or E1)
Mechanical shock Non-operating
Half-sine mechanical shocks, 50 g peak amplitude, 11 msec duration, 3 drops in each direction of each axis (18 total for Option
M01)
Half-sine mechanical shocks, 30 g peak amplitude, 11 msec duration, 3 drops in each direction of each axis (18 total for Options
M00 or E1)
Datasheet
TSG4100A-ATT Option
www.tektronix.com 19
Regulatory information
EC Declaration of Conformity -
EMC
EMC Directive 2004/108/EC EN 61326-1
Radiated and Conducted
emissions
Class A
Australia/New Zealand Australia Radio Communications Act 1992
Korea KCC
Safety
Third Party Certification
Standards
UL 61010; CSA C22.2 No. 61010-1
EC Declaration of Conformity -
Low Voltage
Low Voltage Directive 2006/95/EC; EN61010-1
Safety Certification
Compliance
Equipment type: Test and measuring
Safety class: Class 1 - grounded product
Pollution degree: 2 (as defined in IEC61010-1)
Rated for indoor use only.
TSG4100A Series RF Vector Signal Generator
20 www.tektronix.com
Ordering information
Models
For each of the basic models, there are three required but exclusive model options that need to be specified at the time of order: M00, M01, and E1. Pricing varies based on
chosen option. See the Instrument Options section for details.
TSG4102A Analog signal generator with 2 GHz frequency coverage, basic model
TSG4104A Analog signal generator with 4 GHz frequency coverage, basic model
TSG4106A Analog signal generator with 6 GHz frequency coverage, basic model
Standard accessories
Accessory Description
RF cable 1 meter, N-type to N-type RF cable
Documentation CD All instrument models ship with a CD containing PDF files of user manuals in all available languages.
Installation and Safety Instructions All instrument models ship with a printed Installation and Safety Instructions manual (multi-language: English and Russian).
Calibration Statement of Calibration
Power cord Country specific (see Power cord options)
Warranty
Three years
Instrument options
Hardware options (All regions except North America)
Options M00 or M01 must be specified at the time of instrument order.
M00 Instrument with oven-controlled crystal oscillator (OCXO)
M01 Instrument with voltage-controlled crystal oscillator (VCXO)
GPIB Adds GPIB interface
Hardware options (North America only)
Option E1 must be specified at the time of instrument order.
E1 Instrument with oven-controlled crystal oscillator (OCXO) time-base and GPIB interface
Hardware options (All regions)
TSG4100A-RM1 Single rack mount kit (can be ordered separately)
TSG4100A-RM2 Dual rack mount kit (can be ordered separately)
TSG4100A-ATT 30 dB, 5 W RF attenuator up to 6 GHz
D1 A list of performance verification test results
Datasheet
www.tektronix.com 21
Software options
To upgrade to vector/digital modulation capability and/or add more modulation options after initial purchase, order "TSG4100A-UP + VM xx” instead of “TSG410xA VMxx”.
VM00 Basic vector modulation package with internal 6 MHz modulation bandwidth
VM01 GSM modulation (requires Option VM00)
VM02 GSM EDGE modulation (requires Option VM00)
VM03 W-CDMA modulation (requires Option VM00)
VM04 APCO-25 modulation (requires Option VM00)
VM05 DECT modulation (requires Option VM00)
VM06 NADC modulation (requires Option VM00)
VM07 PDC modulation (requires Option VM00)
VM08 TETRA modulation (requires Option VM00)
VM10 Audio Clip (analog AM and FM)
EIQ External 200 MHz modulation bandwidth (requires Option VM00)
Power plug options
Opt. A0 North America power plug (115 V, 60 Hz)
Opt. A1 Universal Euro power plug (220 V, 50 Hz)
Opt. A2 United Kingdom power plug (240 V, 50 Hz)
Opt. A3 Australia power plug (240 V, 50 Hz)
Opt. A5 Switzerland power plug (220 V, 50 Hz)
Opt. A6 Japan power plug (100 V, 50/60 Hz)
Opt. A10 China power plug (50 Hz)
Opt. A11 India power plug (50 Hz)
Opt. A12 Brazil power plug (60 Hz)
Opt. A99 No power cord
Language options
Request the option below if you would like to order a printed verison of the English User Manual. (An electronic version of this manual is provided as a PDF on the CD that
shipped with your instrument and is also available for download from the Tektronix Web site.)
Opt. L0 English manual
Service options
Opt. C3 Calibration Service 3 Years
Opt. C5 Calibration Service 5 Years
Opt. D1 Calibration Data Report
Opt. D3 Calibration Data Report 3 Years (with Opt. C3)
Opt. D5 Calibration Data Report 5 Years (with Opt. C5)
Opt. R5 Repair Service 5 Years (including warranty)
TSG4100A Series RF Vector Signal Generator
22 www.tektronix.com
Tektronix is registered to ISO 9001 and ISO 14001 by SRI Quality System Registrar.
Product(s) complies with IEEE Standard 488.1-1987, RS-232-C, and with Tektronix Standard Codes and Formats.
Product Area Assessed: The planning, design/development and manufacture of electronic Test and Measurement instruments.
Datasheet
www.tektronix.com 23
TSG4100A Series RF Vector Signal Generator
ASEAN / Australasia (65) 6356 3900 Austria 00800 2255 4835* Balkans, Israel, South Africa and other ISE Countries +41 52 675 3777
Belgium 00800 2255 4835* Brazil +55 (11) 3759 7627 Canada 1 800 833 9200
Central East Europe and the Baltics +41 52 675 3777 Central Europe & Greece +41 52 675 3777 Denmark +45 80 88 1401
Finland +41 52 675 3777 France 00800 2255 4835* Germany 00800 2255 4835*
Hong Kong 400 820 5835 India 000 800 650 1835 Italy 00800 2255 4835*
Japan 81 (3) 6714 3010 Luxembourg +41 52 675 3777 Mexico, Central/South America & Caribbean 52 (55) 56 04 50 90
Middle East, Asia, and North Africa +41 52 675 3777 The Netherlands 00800 2255 4835* Norway 800 16098
People's Republic of China 400 820 5835 Poland +41 52 675 3777 Portugal 80 08 12370
Republic of Korea 001 800 8255 2835 Russia & CIS +7 (495) 6647564 South Africa +41 52 675 3777
Spain 00800 2255 4835* Sweden 00800 2255 4835* Switzerland 00800 2255 4835*
Taiwan 886 (2) 2656 6688 United Kingdom & Ireland 00800 2255 4835* USA 1 800 833 9200
* European toll-free number. If not accessible, call: +41 52 675 3777
For Further Information. Tektronix maintains a comprehensive, constantly expanding collection of application notes, technical briefs and other resources to help engineers working on the cutting edge of technology. Please visit www.tektronix.com.
Copyright © Tektronix, Inc. All rights reserved. Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication supersedes that in all previously published material. Specification and
price change privileges reserved. TEKTRONIX and TEK are registered trademarks of Tektronix, Inc. All other trade names referenced are the service marks, trademarks, or registered trademarks of their respective companies.
03 Mar 2015 77W-60043-0
www.tektronix.com
