T2 Terminator for Projector Lamp Plug and Receptacle Terminal T2 Terminator Tooling Specification Sheet Order No. 63911-4100 FEATURES It is ideally suited for mid-volume bench operations This terminator can be installed in the TM42 and the TM40 press or Base Unit adapter for 3BF press Quick punch removal with the push of a button for fast and easy tooling change Track adjustment capabilities in the T2 Terminators for improved control of the bell mouth size and cutoff tab length T2 Terminator has standardized tooling with the Molex FineAdjust Applicator which will reduce your inventory requirements SCOPE Products: Projector Lamp Plug and Receptacle Terminal, 18-22 AWG. Terminal Terminal Wire Size Insulation Diameter Strip Length Series No. Order No. AWG mm mm In. mm In. 78036 78036-2001 78036-2005 18-22 0.80-0.35 2.06-3.85 .081-.152 3.00-4.00 .118-.158 78037 78037-2001 78037-2005 18-22 0.80-0.35 2.06-3.85 .081-.152 3.00-4.00 .118-.158 DEFINITION OF TERMS BEND UP STRIP LENGTH CONDUCTOR BRUSH BELL MOUTH SEAM ROLLING TWISTING WIRE CONDUCTOR CRIMP CUT-OFF TAB BEND DOWN The above terminal drawing is a generic terminal representation. It is not an image of a terminal listed in the scope. Doc No: ATS-639114100 Revision: A Release Date: 07-28-09 Revision Date: 07-28-09 UNCONTROLLED COPY Page 1 of 5 T2 Terminator for Projector Lamp Plug and Receptacle Terminal CRIMP SPECIFICATION Terminal Series No. 78036 78037 Terminal Series No. 78036 78037 Bell mouth mm In. 0.05-0.30 .002-.012 0.05-0.30 .002-.012 Bend up Bend down Degree (Max) 3 3 3 3 Cut-off Tab Maximum mm In. 0.15 .006 0.15 .006 Conductor Brush mm In. 0.20-1.00 .008-.039 0.20-1.00 .008-.039 Punch Width mm (Ref) Seam Conductor Seam shall not be open Degree (Max) mm In and no wire allowed out 3 5 2.00 .079 of the crimping area 3 5 2.00 .079 Twist Roll After crimping, the crimp profiles should measure the following: Terminal Wire Size Actual mm Series No. 78036 78037 18 AWG 20 AWG 22 AWG 18 AWG 20 AWG 22 AWG 0.80 0.50 0.35 0.80 0.50 0.35 Conductor Crimp Pull Force Minimum Crimp Height Crimp Width (Ref.) mm In. mm In. N Lb. 1.30-1.40 .051-.055 2.00 .079 107.87 24.25 1.15-1.22 .045-.048 2.00 .079 58.84 13.23 1.07-1.15 .042-.045 2.00 .079 39.23 8.82 1.30-1.40 .051-.055 2.00 .079 107.87 24.25 1.15-1.22 .045-.048 2.00 .079 58.84 13.23 1.07-1.15 .042-.045 2.00 .079 39.23 8.82 Tool Qualification Notes: 1. The above specifications are guidelines to an optimum crimp. Doc No: ATS-639114100 Revision: A Release Date: 07-28-09 Revision Date: 07-28-09 UNCONTROLLED COPY Page 2 of 5 T2 Terminator for Projector Lamp Plug and Receptacle Terminal PARTS LIST T2 Terminator 63911-4100 Item Order No Engineering No. Description Quantity Perishable Tooling 63911-4170 63911-4170 Tool Kit (All "Y" Items) REF 1 63444-2017 63444-2017 Conductor Punch 1Y 63455-0084 63455-0084 Conductor Anvil 1 Y 2 3 63443-0035 63443-0035 Front Cut-Off Plunger 1Y 4 63443-0036 63443-0036 Front Plunger Retainer 1Y Other Components 5 11-18-4083 60707-8 Feed Guide 1 6 63443-3160 63443-3160 Front Plunger Striker 1 7 63443-0009 63443-0009 Front Scrap Chute 1 8 63443-0024 63443-0024 Key 1 9 63443-0085 63443-0085 Wire Stop L-Bracket 1 10 63443-0090 63443-0090 Wire Stop 1 11 63443-1718 63443-1718 18.80mm Height Spacer 1 63443-2215 63443-2215 15.00mm Coarse Spacer 2 12 63443-2314 63443-2314 3.70mm Fine Spacer 1 13 14 63443-6004 63443-6004 Rear Cover 1 63454-0101 63454-0101 Punch Spacer 1 15 16 63700-0539 63700-0539 Cut-Off Plunger Spring 1 Frame 17 63800-8500 63800-8500 T2 Terminator 1 Hardware 18 N/A N/A M3 by 6 Long FHCS 1** 19 N/A N/A M3 by 6 Long SHCS 2** 20 N/A N/A M4 by 6 Long SHCS 2** 21 N/A N/A M4 by 12 Long BHCS 2** 22 N/A N/A M4 by 14 Long SHCS 2** 23 N/A N/A M4 by 45 Long SHCS 2** 24 N/A N/A M5 by 12 Long SHCS 1** 25 N/A N/A #10-32 by 3/8"Long BHCS 1** ** Available from an industrial supply company such as MSC (1-800-645-7270). Doc No: ATS-639114100 Revision: A Release Date: 07-28-09 Revision Date: 07-28-09 UNCONTROLLED COPY Page 3 of 5 T2 Terminator for Projector Lamp Plug and Receptacle Terminal Assembly Drawing 21 (2) (2) 19 14 5 1 15 9 22 (2) 6 10 25 24 3 17 13 16 2 10 4 20 12 11 Figure 1 8 18 23 7 20 (2) Doc No: ATS-639114100 Revision: A Release Date: 07-28-09 Revision Date: 07-28-09 UNCONTROLLED COPY Page 4 of 5 T2 Terminator for Projector Lamp Plug and Receptacle Terminal NOTES 1. Molex recommends an extra perishable tooling kit be maintained at your facility. 2. Verify tooling alignment by manually cycling the press before crimping under power. Check that all screws are tight. 3. Slugs, Terminals, Dirt and Oil should be kept clear of work area. 4. This Terminator should be only used in a Molex TM42, TM40, or 3BF Press with a Base Unit adaptor. 5. Wear safety glasses at all times. 6. For recommended maintenance refer to the TM40, TM42 Manual. CAUTION: To prevent injury never operate this Terminator without the guards supplied with the press in place. Reference the TM42 press manufacturer's instruction manual. CAUTION: Molex crimp specifications are valid only when used with Molex terminals, applicators and tooling. Americas Headquarters Lisle, Illinois 60532 U.S.A. 1-800-78MOLEX amerinfo@molex.com Far East North Headquarters Yamato, Kanagawa, Japan 81-462-65-2324 feninfo@molex.com Far East South Headquarters Jurong, Singapore 65-6-268-6868 fesinfo@molex.com European Headquarters Munich, Germany 49-89-413092-0 eurinfo@molex.com Corporate Headquarters 2222 Wellington Ct. Lisle, IL 60532 U.S.A. 630-969-4550 Fax: 630-969-1352 Visit our Web site at http://www.molex.com Doc No: ATS-639114100 Revision: A Release Date: 07-28-09 Revision Date: 07-28-09 UNCONTROLLED COPY Page 5 of 5