TR CALIFORNIA MICRO DEVICES Thin Film Resistor Series California Micro Devices TR Series resistors offer a high degree of stability and low noise as well as the proven reliability characteristics of Tantalum Nitride. TR Series 20 mil chips offer these advantages in a broad range of standard center tapped resistors in total values up to one meg ohm and tolerances as low as 0.5 percent. Electrical Specifications Parameter Conditions TCR -55C to 125C 1 0 0 p p m/ C Ma x Op e r a t i n g Vo l t a g e -55C to 125C 100Vdc Ma x Powe r Ra t i n g ( p e r r e s i s t o r ) @ 7 0 C ( D e r a t e l i n e a r l y t o ze r o @ 1 5 0 C ) 2 5 0 mw Ma x T h e r m a l S h o ck Me t h o d 1 0 7 MI L - STD- 2 0 2 F 0 . 5 %@R Ma x Hi g h Te mp e r a t u r e Ex p o s u r e 1 0 0 Hr s @ 1 5 0 C Amb i e n t 0 . 2 5 %R Ma x Mo i s t u r e Re s i s t a n c e Me t h o d 1 0 6 MI L - STD- 2 0 2 F 0 . 5 %R Ma x L i fe Noi se 0 . 5 %R -25dB -20dB 1.0% Ma x Ma x Ce n t e r t a p To l e r a n c e Me t h o d 1 0 8 MI L - STD- 2 0 2 F ( 1 2 5 C/ 1 0 0 0 h r ) Me t h o d 3 0 8 MI L - STD- 2 0 2 F 250K R 1/ R 2 @2 5 C I nsul at i on Resi st ance @2 5 C 1 X 1 0 12 Mi n Va l u e s Bonding Area From 4.7 to 1 meg for each resistor. Values>1 meg ohms use proprietary resistor material. Laser Code Area Mechanical Specifications Formats Substrate Die Size: 303 mils square Bonding Pads: 4x4 mils typical Isolation Layer Si02 10,000A thick, min Backing Lapped (gold optional) Metalization Aluminum 10,000A thick, min (15,000A gold optional) 4.7 to 470 R1 Silicon 102 mils thick Pa ck a g i n g R2 Two inch square trays of 400 chips maximum is standard. Notes 1. Code boxes for alpha numeric laser marking are available. 2. Resistor pattern may vary from one value to another. 470 to 1M Pa r t N u m b e r D e s i g n a t i o n TR Series 1002 Value Fi rst 3 di gi t s are si gni fi cant va l u e . Last di gi t represents nu mb e r o f ze r o s. R i ndi cates d e c i ma l p o i n t . F A Tolerance TCR G W P Bond Pads Backing Ratio Tolerance D = 0.5% No Let t er = 100ppm G = Gol d W = Gol d No Let t er = 1% F = 1% A = 50ppm No Let t er = Al u mi nu m L = Lapped P = 0.5% G = 2% B = 25ppm No Letter = Either J = 5% K = 10% M = 20% C1320800 (c) 2000 California Micro Devices Corp. All rights reserved. 8/7/2000 215 Topaz Street, Milpitas, California 95035 Tel: (408) 263-3214 Fax: (408) 263-7846 www.calmicro.com 1