DOCUMENT NUMBER NCD-5DB4-01
SAP-4 Series
Single-Mode
FC φ0.9mm HOUSING
TECHNICAL SPECIFICATIONS
Seiko Instruments Inc.
Components Sales Dept.
8, Nakase 1-Chome
Mihama-ku, Chiba-shi, Chiba-ken
261 JAPA N
Telephone : 043-211-1214
-1215
Facsimile : 043-211-8035
SAP-4 Series Single-Mode FC φ0.9mm HOUSING
TECHNICAL SPECIFICATIONS
Document Number NCD-5DB4-01
NAE69D02 " SAP-4 Part " September 1986
NCD-5DB4-01 December 1995
Copyright 1986, 1995 by Seiko Instruments Inc.
All right reserved.
The information contained herein shall not reproduced or disclosed to any third party
without the express written consent of SII.
The Specifications contained herein are subject to change without notice.
SIIis a trademark of Seiko Instruments Inc.
Please address any questions, comments, and suggestions to:
Seiko Instruments USA Inc.
Electronics Components Division
2990 West Lomita Boulevard
Torrance, CA 90505, U.S.A.
Phone: 310-517-7780
Fax: 310-517-7792
Seiko Instruments GmbH
OFC Division
Siemensstraße 9b
D-63263 Neu-Isenburg, Germany
Phone: 06102-297-0
Fax: 06102-297-211
Seiko Instruments (H.K.) Ltd.
Sales Department
4th & 5th Floor, Wyler Center 2
200 Tai Lin Pai Road, Kwai Chung
N.T., Kowloon, Hong Kong
Phone: 852-2421-8611
Fax: 852-2480-5479
Seiko Instruments Taiwan Inc.
Sales Department
5F-1, No.99, Sec. 2, Chung Shan
Rd.
Taipei 104, Taiwan, R.O.C.
Phone: 02-563-5001, 523-5111
Fax: 02-521-9519
Seiko Instruments Singapore pte. Ltd.
2, Marsiling Lane,
Woodlands New Town,
Singapore, 2573, Singapore
Phone: 65-2691370
Fax: 65-2699729
ii
TABLE OF CONTENTS
Section Page
1. PROVISION 1
1.1 Application Limit 1
2. PARTS NUMBER 1
3. GENERAL SPECIFICATIONS 2
3.1 Parts and Materials 2
3.2 Physical Dimensions 2
3.3 General Tolerances 2
4. PACKING 3
Table
Table 1 Parts Number 1
Table 2 Parts and Materials 2
Table 3 General Tolerance 2
Figure
Figure 1 SAP-4 Housing 4
Figure 2 to 7 Part Dimensions 5 to 7
iii
iv
1
1. PROVISION
1.1 Application Limit
These specifications apply to the SAP-4 Single-Mode FC φ0.9mm HOUSING supplied
by SII.
2 . PARTS NUMBER
Parts Number of the Housing is Shown in Table 1.
Table 1 Parts Number
2
3. GENERAL SPECIFICATIONS
3.1 Parts and Materials
Parts and the Materials are shown in Table 2.
Table 2 Parts and Materials
No. Part Name Q'ty Material Notes
①Frame 1 Stainless Steel - -
②Keyring 1 Beryllium Copper - -
➂Spring 1 Stainless Steel - -
➃Coupling nut 1 Brass Nickel Plating
⑤Stopper -- - (⑤-a,b,c )
⑤-a Stopper body 1 Brass Nickel Plating
⑤-b Spacer 1 Brass Nickel Plating
⑤-c Hood (1) Synthetic Rubber Hood Color Shows Table 1
➅Cap (1) Plastics White
3.2 Physical Dimensions
Figure 1 shows the assembled state of SAP-4.
Figure 2 to 7 show the part dimension.
•In accordance with JIS C5970 F01 type connectors
3.3 General Tolerances
Permissible deviation in dimensions without tolerance indication is in accordance with JIS
B 0405 class m, as shown in Table 3.
Table 3 General Tolerance (JIS B 0405 class m)
Basic size step (mm)
Over Under Permissible deviation (mm)
0.5 3
36
630
30 120
±0.1
±0.1
±0.2
±0.3
3
4 . PACKING
The product is packed to prevent damage during shippment.
4
note.1: This drawing does not include Caps. Unit: mm
Figure 1 SAP-4 HOUSING
5
Unit: mm
Figure 2 ①Frame
Unit: mm
Figure 3 ②Keyring
Unit: mm
Figure 4 ➂Spring
6
Unit: mm
Figure 5 ➃Coupling nut
Unit: mm
Figure 6 ⑤Stopper
7
Unit: mm
Figure 7 ➅Cap
