Avantek Products HEWLETT* PACKARD | YIG-Tuned Oscillators With Analog or Digital Drivers Technical Data Features * Analog Driver, 0 to +10 VDC Tuning * Digital Driver, 12 Bit TTL Applications * Bench-top Sources Instrumentation Test and Measurement Equipment eee =Block Diagram I O/A I Converter t-- (Digital) | S or ----! Main Tune - Current Driver. 0 Butter Vtol Converter (Analog) Description HP YIG-tuned oscillators are available with either digitally- tuned or analog voltage-tuned drivers. These drivers control the main tuning coil current. via 12-bit digital logic or via an analog voltage thus eliminating the need to build and align tuning current sources, Common Pole YIG Sphere Basic Digital/Analog Driver Hookup to a YTO 5963-3255E 3-66 AVD Series coe ADD Series Both the digital and analog drivers are available in two temperature range version; 0 to 65C and 54 to +85C., The former is used with any HP YIG-tuned devices speci- fied over 0 to +65C while the extended temperature range version will meet all of the environmental specifications of HP's militarized YIG-tuned devices including operation over the -54 to +85C temperature range. RF OutputElectrical and Performance Specifications Guaranteed Specifications at 25C Case Temperature (Operating Temperature Per Device) Specification! Analog Driver Digital Driver Tuning Range ining Accuracy: at 25C on baseplate, our after turn-on, excluding V7 afesis and non-linearily Slution 8 rface Logic ting Input Resistance mmon Mode Rejection sidual FM: (15 Hz~15 kHz bandwidth) .on-Linearity Aushing: +15 Volts: ~15 Volts: Power Supply Voltage: Power Supply Current: +15 Volts: -15 Volts: Weight Device Specifications That Do Not. Apply 0,000 volts at input corresponds to lowest frequency 10.000 volts at input corresponds to highest frequency +(0,1% of frequency +2 MHz) NA NA 210 kQ 240 dB +x 10-4 of oscillator frequency in hertz +40 kHz, typ. Device specification applies +(0.01% of frequency +1 MHz + oscillator pushing)/volt. typ. +(0.01% of frequency +1 MIIz)/volt, typ. +15 volts: 5% Oscillator bias current + tuning current at max freq +30 mA (Current. requirement of 5 volts of oscillator if present +30 mA) Oscillator weight +12 oz. Main Tuning Coil Sensitivity Main Tuning Coil Input Impedance at. 1 kHz Pushing Figure, 5 volts if used All zeros at input corresponds to lowest frequency All ones at input corresponds to highest frequency +(0.1% of frequency +2 MHz) 12 bit positive true logic for increasing frequency TTL or CMOS NA NA 4x10-6 of oscillator frequency in hertz +40 kHz, typ. +(1/2 bit + device non-linearity) (0.001% of frequency +0.1 MHz + oscillator pushing)volt, typ. (0.001% of frequency +1 MHz)/volt, typ. +15 volts: 5% Oscillator bias current + tuning current at max freq +40 mA (Current requirement of 5 volts of oscillator if present +40 mA) Oscillator weight +13 oz. Main Tuning Coil Sensitivity Main Tuning Coil Input Impedance at 1 kHz Pushing Figure, 5 volts if used Notes: is coupled, except as noted. 2. Tuning current at max freq is: Product Options Model Number Prefix. <____ AVD Analog Driver, 0 to 10 Volts Tuning ADD - Digital Driver, 12 Bit TTL Tuning Model Number <__ Max freq (MEIz) 1, These specifications are in addition to the standard specifications for the basic YIG device to which the driver __Emee _ = Max current (mA) Sensitivity (MHz/mA) AVD XXXXX P Options P Low Phase Noise Driver Option No Suffix - Standard Driver Configuration 3-67Electrical and Performance Specifications Guaranteed Specifications at 25C Case Temperature (Operating Temperature Per Device) Analog Driver Specification Data Digital Driver Specification Data AVD-XXXXX ADD-XXXXX El! E2! P1-12! P1-25! Pi-13! Frequency Power Supply Current Residual FM Power Supply Current Residual FM Range (mA), Max. @ VDC Nom (kHz p-p) (mA), Max. @ VDC Nom (kHz p-p) Model Number (GHz) +15V -15V Typical +15 V -15V +15 V Typical AV-70502 0.5-2.0 Not Available Not Available ~. AV-7104 1.0-2.2 300 30 50 190 AO 120 AV-7104-9 1.0-2.2 300 30 AO 190 40 120 AV-7114 1.0-4.0 Nol Available Not. Available AV-7124 1.04.0 390 85 60 140 95 260 60 AV-7134 1.24.0 Not Available Not Available AV-7203 2.0-4.0 350 30 60 140 40 220 60 AV-7214 2.0-4.0 510 95 60 240 105 280 60 AV-7224 2.0-4.0 390 95 60 190 105 210 60 AV-7224-9 2.0-4.0 390 95 60 190 105 210 60 AV-7246 2.0-6.0 655 95 60 240 105 425 60 AV-7028 2.0-8.0 Not Available Not Available AV-7278 2.0-8.0 795 95 70 240 105 565 70 AV-7288 2.0-8.0; 700 95 70 290 105 420 70 AV-7298 2.0-8.0 650 95 70 240 105 420 70 AV-72B8 2.0-8.0 800 95 70 390 105 420 7 AV-72810 2.0-10.0 760 60 80 240 70 530 80 AV-72012 2.0-12.4 860 60 90 215 70 854 90 AV-72018 2.0-18.0 1380 65 110 340 Th 1060 110 AV-7036 3,0-6,0 Not Available Not Available AV-7418 4.0.8.0 795 95 70 240 105 565 70 AV-7443 4.0-8.0 650 95 70 240 105 420 70 AV-7443-9 4.0-8.0 650 95 70 240 105 420 70 AV-7453 4.0-8.0 600 95 70 190 105 420 70 AV-7453-9 4.0-8.0 600 95 70 190 105 420 70) AV-74010 4.0-10.0 760 95 80 240 105 30 80 AV-74012 4.0-12.4 Not Available Not Available AV-74018 4.0-18.0 1440 65 10 390 75 1060 110 AV-76118 6.0-18.0 1365, 30 110 315 40 1060 110 AV-76318 6.0-18.0 140 65 110 390 75 1060 110 AV-78012 8.0-12.4 935 15 90 290 85 655 90 AV-7814 8.0-12.4 935 30 90 215 40 730 90 AV-78112 8.0-124 1034 30 90 Sah 40 730 90 AV-7871 8.0-12.4 810 30 90 165 40 655 90 AV-7871-9 8.0-12.4 810 30 0 165 40 655 90 AV-7873 8.0-12.4 935 20 90 290 40 655 90 AV-7873-9 8.0-12.4 935 30 0) 200 40 655 90 AV-78218 8.0-18.0 1265 30 110 215 40 TO) 110 AV-78518 8.0-18.0 1365 30 110 B15 40 1060 110 AV-78618 8.0-18.0 1365 30 lo 316 40 1060 L10 AV-78020 8.0-20.0 1360 30 120 315 40 1055 120 AV-78020-9 8.0-20.0 1360 30 120 315 40 1055 120 AV-12018 12.0-18.0 1440 65 110 390 75 1060 110 AV-12118 12.0-18.0 1365 30 oO 315 40 1060 lio AV-12218 12,0-18.0 Not Available Not Available AV-71251 (2.0-18.0 1240 30 110 190 40 1060 L110 AV-71251-9 12.0-18.0 1240 30 110 190 40 1060 10 AV-71220 L2.0-20.0 1405 30 120 240 40 WS 120 AV-18126 18.0-26.5 1160 30 150 240 40 930 150 AV-18326 18.0-26.5 1160 30 150 240 40 930 150 AV-18030 18.0-30.0 1285 30 160 240 40 1055 160 AV-20040 20.040.0 Not Available 200 290 40 1055 @ +20V 200 AV-26140M 26.5-40.0 1235 30 200 190 40 1055 200 AV-26140W 26.5-40.0 1235 30 200 190 40 1055 200 AV-26240M 26.5-40.0 1235 30 200 19) 40 1055 200 AV-26240W 26.5-40.0 1235 30 200 L90 40 1055 200 AV-33050 33.0-50.0 Not Available 190 40 1070) @ +20V 240 Note t: Refer to Case Drawing section for pin designations. 3-68