UL62H256ASK55 - ZMD AG - Product.Network

1 November 01, 2001

UL62H256A

F32768 x 8 bit static CMOS RAM

F35 and 55 ns Access Time

FCommon data inputs and

data outputs

FThree-state outputs

FTyp. operating supply current

35 ns: 45mA

55 ns: 30mA

FStandby current < 50 µA at 125° C

FTTL/CMOS-compatible

FPower supply voltage 3.3 V

FOperating temperature range

-40 °C to 85 °C

-40 °C to 125 °C

FCECC 90000 Qua lity Standard

FESD protection > 2000 V

(MIL STD 883C M3015.7)

FLatch-up im mun ity >100 mA

FPackage: SOP28 (300/330 mil)

The UL62H256A is a static RAM

manufactured using a CMOS pro-

cess technology with the following

operating modes:

- Read - Standby

- Write - Data Retention

The memory array is based on a

6-Transistor cell.

The circuit is activated by the fal-

ling edge of E. The address and

control inputs open simul taneously.

According to the information of W

and G, the data inputs, or outputs,

are active. In a Read cycle, the

data outputs are activated by the

falling edge of G, afterwards the

data word will be available at the

outputs DQ0-DQ7. After the

address change, the data outputs

go High-Z until the new informa tion

is available. T he data outputs have

no preferred state. The R ead cycle

is finished by the falling edge of W,

or by the rising edge of E, respec-

tively.

Data retention is guaranteed down

to 2 V. With the exception of E, all

inputs consist of NOR gates, so

that no pull-up/pull-down resistors

are required.

Low Voltage Automotive Fast 32K x 8 SRAM

Pin Configuration

Top View

Signal Name Signal Descripti on

A0 - A14 Address Inputs

DQ0 - DQ7 Data In/Out

EChip Enable

GOutput En able

WWrite Enable

VCC Power Supply

Voltage

VSS Ground

Pin Descript ion

A14 VCC28

2A12 W

4A6 A825

5A5 A924

3A7 A1326

6A4 A1123

7A3 G

8A2 A1021

12DQ1 DQ517

9A1 E

A0 DQ719

11DQ0 DQ618

13DQ2 DQ416

14VSS DQ315

SOP

Features Description

2 November 01, 200 1

UL62H256A

a Stresses greater than those listed under „Absolute Maximum Ratings“ may cause permanent damage to the device. This is a stress rating

only, and functional operation of the device at condition above those indicated in the operational sections of this specificatio n is n ot im plie d.

Exposure to absolute maximum rating conditions for extended periods may affect reliability

b Maximum voltage is 4.6 V

c Not more than 1 output should be shorted at the same time. Duration of the short circuit should not exceed 30 s.

*H or L

Operati ng Mod e E W G DQ0 - DQ7

Standby/not selected H * * High-Z

Internal Read L H H High-Z

R ead L H L Data Outputs Low-Z

Write L L * Da ta In p uts Hig h-Z

Tr uth Ta ble

Block Diagram

Maxim um Ratings a Symbol Min. Max. Unit

Power Supply Voltage VCC -0.3 4.6 V

Input Voltage VI-0.5 VCC + 0.5 bV

Outpu t Vol tage VO-0.5 VCC + 0.5 bV

Power Dissipa tion PD-1W

Operating Temperature K-Type

A-Type Ta-40

-40 85

125 °C

Storage Temperature Tstg -65 150 °C

Outpu t Short-Circuit Current

at VCC = 3.3 V and VO = 0 V c| IOS |100mA

Characteristics

All voltages a re referenced to VSS = 0 V (ground).

All characteristics are valid in the power su pply voltage ra nge and i n the ope rat ing temperature range spe cifie d.

Dynamic m easurem ents are based on a ris e and fall time of ≤ 5 ns, measured between 10 % and 90 % of VI,as well as

input levels of VIL = 0 V and VIH = 3 V. The tim ing refere nce level of all input and out put signals is 1.5 V,

with the exception of the tdis-times and ten-tim es, in which c ases transi tion is m easured ±200 mV from steady-state voltage.

DQ0

DQ1

DQ2

DQ3

DQ4

DQ5

DQ6

DQ7

VCC VSS W GE

Row Address

Inputs

Column Address

Inputs

Address

Change

Detector

Column Decoder Row Decoder

Se ns e Amp lifie r /

Write Control Logic

Clock

Generator

Co mmo n Data I/O

Memory Cell

Array

512 Ro ws x

64 x 8 Columns

A10

A11

A12

A13

A14

3 November 01, 2001

UL62H256A

Recommended

Operating Conditions Symbol Conditions Min. Max. Unit

Power Supply Voltage VCC 3.0 3.6 V

Input Low V ol t age d VIL -0.3 0.6 V

Input High V o ltage VIH 2.2 VCC + 0.3 V

Electrical Characteristic s Symbol Co nd itions Min. Max. Unit

Suppl y Current - Operating Mode

Suppl y Current - Standby Mode

(CMOS level)

Suppl y Current - Standby Mode

(TT L lev e l)

ICC(OP)

ICC(SB)

ICC(SB)1

VCC

VIL

VIH

tcW

VCC

K-Type

A-Type

= 3.6 V

= 0.6 V

= 2.2 V

= 35 ns

= 55 ns

= 70 ns

= 3.6 V

= VCC - 0.2 V

= 3.6 V

= 2.2 V

µA

Outpu t High Voltage

Outpu t Low Voltage

VOH

VOL

VCC

IOH

VCC

IOL

= 3.0 V

=-1 mA

= 3.0 V

= 2.1 mA

2.4

0.4

Input High Leakage Current

Input Low Leakage Current

IIH

IIL

VCC

VIH

VCC

VIL

= 3.6 V

= 0 V -2

2µA

µA

Outpu t High Current

Outpu t Low Current

IOH

IOL

VCC

VOH

VCC

VOL

= 3.0 V

= 2.4 V

= 3.0 V

= 0.4 V 2.1

-1 mA

Outpu t Leakage Current

High at Three-State Outputs

Low at Three-St ate Outputs

IOHZ

IOLZ

VCC

VOH

VCC

VOL

= 3.6 V

=0 V -2

2µA

µA

d -2 V at Pulse Width 30 ns

4 November 01, 200 1

UL62H256A

Switching Characteristics

Read Cycle

Symbol 35 55 Unit

Alt. IEC Min. Max. Min. Max.

Read Cycle Time tRC tcR 35 55 ns

Address Access Time to Data Valid tAA ta(A) 35 55 ns

Chip Enable Access Tim e to Data Valid tACE ta(E) 35 55 ns

G LOW to Data Valid tOE ta(G) 15 25 ns

E HIGH to Output in High-Z tHZCE tdis(E) 12 15 ns

G HIGH to Output in High-Z tHZOE tdis(G) 12 15 ns

E LOW to Output in Low-Z tLZCE ten(E) 33ns

G LOW to Output in Low-Z tLZOE ten(G) 00ns

Output Hold Ti me from Address Change tOH tv(A) 33ns

E LOW to Power-Up Time tPU 00ns

E HIGH to Power-Down Time tPD 35 55 ns

Switching Characteristics

Write Cycle

Symbol 35 55 Unit

Alt. IEC Min. Max. Min. Max.

Write Cycle Ti me tWC tcW 35 55 ns

Write Pulse Width tWP tw(W) 20 35 ns

Wr ite Setup Time tWP tsu(W) 20 35 ns

Address Setup Time tAS tsu(A) 00ns

Address Valid to End of Write tAW tsu(A-WH) 25 40 ns

Chip Enable Setup Time tCW tsu(E) 25 40 ns

Pulse Width Chip Enable to End of Write tCW tw(E) 25 40 ns

Da ta Se tu p Time tDS tsu(D) 15 25 ns

Data Hold Time tDH th(D) 00ns

Address Hold from End of Write tAH th(A) 00ns

W LOW to Output in High-Z tHZWE tdis(W) 15 20 ns

G HIGH to Output in High-Z tHZOE tdis(G) 12 15 ns

W HIGH to Output in Low-Z tLZWE ten(W) 00ns

G LOW to Output in Low-Z tLZOE ten(G) 00ns

5 November 01, 2001

UL62H256A

Data Retention Mode

E - controlled

Data Retention

3.0 V

tsu(DR) trec

VCC

VCC(DR) ≥ 2 V

0 V

2.2 V

VCC(DR) - 0.2 V ≤ VE(DR) ≤ VCC(DR) + 0.3 V

Data Retention

Characteristics Symbol Conditions Min. Typ. Max. Unit

Alt. IEC

Data Retention Sup ply Voltage VCC(DR) 2V

Data Retention Supply Current ICC(DR) VCC(DR) = 2 V

VE = VCC(DR) - 0.2 V 30 µA

Data Retention Setup Time tCDR tsu(DR) See Data Retention

Waveforms (above) 0ns

Operating Recovery T i m e tRtrec tcR ns

Test Configuration for Functional Check

DQ0

DQ1

DQ2

DQ3

DQ4

DQ5

DQ6

DQ7

VIH

VIL

VSS

VCC

3.3 V

1213

1375

Inpu t level a ccordi ng to the

relevant test measurem ent

Simultaneous measure-

ment of all 8 output pins

A10

A11

A12

A13

A14

30 pF e

e In measurement of tdis(E),tdis(W), ten(E), ten(W), ten(G) the capacitance is 5 pF.

6 November 01, 200 1

UL62H256A

Capacitance Conditions Symbol Min. Max. Unit

Input Capacit ance VCC

= 3.3 V

= VSS

= 1 MHz

= 25 °C

CI7pF

Output Capacitance Co7pF

IC Code Numbers

UL62H256A SA35

Type

Package

S = SOP28 300 m il

S1 = SOP 28 330 mi l

Opera tin g Temperatur e Range

K = -40 to 85 °C

A = -40 to 125 °C

Access Time

35 = 35 ns

55 = 55 ns

The date of manufacture is given by the last 4 digits of the mark, the first 2 digits indicating the year, and the last 2

digits the c al endar week.

All pins not under test must be connec ted with ground by capacitors.

7 November 01, 2001

UL62H256A

tPU

tdis(G)

tdis(E)

tcR

Previous Data Valid Output Data Valid

Ad dres s Va lid

Addres s Valid

tsu(A)

High-Z

ten(E)

ten(G)

ta(G)

ta(E)

Read Cycle 1: Ai-con trolled (during Read Cycle : E = G = VIL, W = VIH)

Read Cycle 2: G-, E- controlled (during Read Cycle: W = VIH)

ta(A)

tcR

tv(A)

DQi

Output

DQi

Output tPD

ICC(OP)

ICC(SB) 50 % 50 %

Ou tp ut Data Valid

8 November 01, 200 1

UL62H256A

Write Cycle1: W-controlled

th(D)

DQi

Input

DQi

Output

tcW

tsu(E) th(A)

tw(W)

tsu(A) tsu(D)

tdis(W) ten(W)

Address

In p ut Da ta Valid

High-Z

tsu(A-WH)

Write Cycle 2: E-co ntrolled

Inp ut D ata Vali d

tsu(A)

th(D)

DQi

Input

DQi

Output

tcW

tw(E) th(A)

tsu(W)

tsu(D)

tdis(W)

en(E)

High-Z

Address Valid

tdis(G)

L- to H- l e v e l undefined H- to L-l e ve l

The information describes the type of component and shall not be considered as assured characteristics.Terms of

delivery and rights to change design reserved.

Zentrum Mikroelektronik Dresden AG

Grenzstra ße 28 • D-01109 Dresden • P. O. B. 80 01 34 • D-01101 Dresden • Germany

Phone: +49 351 8822 306 • Fax: +49 351 8822 337 • Email: sales@zmd.de • http://www.zmd.de

November 01, 2001

UL62H256A

LIFE SUPPO R T POLICY

ZMD products are not designed, intended, or authorized for use as components in systems intended for surgical

imp lant into the body, or other applications in tended to supp ort or s ustain life, o r for any other ap plication in which

the failure of the ZMD product could create a situation where personal injury or death may occur.

Components used in life-support devices or systems must be expressly authorized by ZMD for such purpose.

LIMITED WARRANTY

The information in this document has been carefully checked and is believed to be reliable. However Zentrum

Mikroelektronik Dresden AG (ZMD) makes no guarantee or warranty concerning the accuracy of said information

and shall not be responsible for any loss or damage of whatever nature resulting from the use of, or reliance upon it.

The i nfo rmation in this doc um ent desc ribes the type o f com pone nt and shall not be co nsidered a s assure d charac -

teristics.

ZMD does not guarantee that the use of any information contained herein will not infringe upon the patent, trade-

mark, copyright, mask work right or other rights of third parties, and no patent or licence is implied hereby. This

document does not in any way extent ZMD’s warranty on any product beyond that set forth in i t s s tandard terms and

con ditions of sale.

ZM D reserves term s of del ivery and reserv es the right to make cha nges in t he products or specifications, or bot h,

presented in this publication at any time and without notice.