ECP150PS48 - XP POWER - Product.Network

ACDC

Specification

150 Watts

•100 W Convectioncooled

•150 W Forcedcooled

•2” x 4” Foot Print

•Single Outputs from 12 V to 48 V

•Builtin Fan Supply

•<0.5 W No Load Input Power

•3 Year Warranty

ECP Series

Input

Input Voltage • 90-264 VAC (120-370 VDC),

Derate from 100% load at 100 VAC to

90% load at 90 VAC

Input Frequency • 47-63 Hz

Input Current • 1.5 A max at 115 VAC, 0.75 A max at

230 VAC

Inrush Current • 60 A max at 230 VAC, cold start at 25 °C

Power Factor • >0.95 at full load, 230 VAC

Earth Leakage Current • 230 µA at 264 VAC, 60 Hz.

No Load Input Power • <0.5 W

Input Protection • Internal T3.15A/250VAC fitted in line and

neutral

Output

Output Voltage • See tables

Output Voltage Trim • ±10%

Initial Set Accuracy • ±1% at 50 % load

Minimum Load • No minimum load requirement

Start Up Delay • 550 ms typical

Start Up Rise Time • 35 ms typical

Hold Up Time • 16 ms minimum at full load and 115 VAC

Line Regulation • ±0.5% max

Load Regulation • ±0.5% max

Transient Response • 4% maximum deviation, recovering to less

than 1% within 500 µs for 25% step load

Ripple & Noise • 1% max pk-pk, 20 MHz bandwidth,

(see note 2)

Overvoltage Protection • 115% - 140% of nominal voltage on main

output. Recycle mains to reset.

Overload Protection • 110-150%

Short Circuit Protection • Trip and restart (hiccup)

Temperature • 0.02%/°C

Coefficient

Fan Supply • 12 V at 500 mA

xppower.com

General

Efficiency • See table

Isolation • 4000 VAC Input to Output

1500 VAC Input to Ground

500 VDC Output to Ground

Protection Level • Primary to Secondary: 2 MOPP

Primary to Earth: 1 MOPP

Switching Frequency • 60 kHz ± 10 kHz

MTBF • 300 kHrs to MIL-HDBK-217F at 25 °C, GB

Environmental

Operating Temperature • -20 °C to +70 °C derate from 100% load

at 50 °C to 50% load at 70 °C

Cooling • Convection cooled: 100 W

Forced cooled: 150 W with 10 CFM

Operating Humidity • 5% to 90% RH, non condensing

Operating Altitude • 3000 m

Storage Temperature • -40 °C to +85 °C

Shock • IEC68-2-6, 30 g, 11 mins half sine, 3 times

in each of 6 axes

Vibration • IEC68-2-27, 10-55 Hz, 2 g 10 mins /

sweep. 60 mins for each of 3 axes

EMC & Safety

Emissions • EN55022/11, Level B conducted &

Level A radiated

Harmonic Currents • EN61000-3-2 Class A

EN61000-3-2 Class C for load >60 W

Voltage Flicker • EN61000-3-3

ESD Immunity • EN61000-4-2, ±8 kV air, ±4 kV contact,

Perf Criteria A

Radiated Immunity • EN61000-4-3, 10 V/m, Perf Criteria A

EFT/Burst • EN61000-4-4, level 3, Perf Criteria A

Surge • EN61000-4-5, installation class 3,

Perf Criteria A

Conducted Immunity • EN61000-4-6, 10 V, Perf Criteria A

Dips & Interruptions • EN55024, 100% 10 ms,

30%, 500 ms, 100%, 5000 ms

Perf Criteria A, A, B for high line,

A, B, B for low line at full load,

EN60601-1-2, 30% 500 ms, 60% 100 ms,

100% 10 ms, 100% 5000 ms,

Perf Criteria A, A, A, B for high line,

A, B, A, B for low line at full load

Safety Approvals • UL60950-1, IEC60950-1, EN60950-1,

ANSI/AAMI ES 60601-1, IEC60601-1,

EN60601-1

Mechanical Details

30-Sept-13

ACDC

ECP150

Models and Ratings

Output Voltage Output Current Ripple and Noise

pk-pk(2) Fan Output Efficiency(3) Model Number

Convection-cooled Forced-cooled(1)

12.0 V 8.33 A 12.50 A 120 mV 12 V/0.5 A 91% ECP150PS12

15.0 V 6.67 A 10.00 A 150 mV 12 V/0.5 A 91% ECP150PS15

24.0 V 4.17 A 6.25 A 240 mV 12 V/0.5 A 91% ECP150PS24

28.0 V 3.50 A 5.40 A 280 mV 12 V/0.5 A 92% ECP150PS28

48.0 V 2.08 A 3.10 A 480 mV 12 V/0.5 A 92% ECP150PS48

1. Requires 10 CFM.

2. Measured with 20 MHz bandwidth and 10 µF electrolytic capacitor in parallel

with 0.1 µF ceramic capacitor

3. Minimum average efficiencies measured at 25%, 50%, 75% & 100% of

150 W load and 230 VAC input.

Notes

TB1 - Input Connector

Pin 1 Line

Pin 2 Not Fitted

Pin 3 Neutral

TB2 - Output Connector

Pin 1 +Vout

Pin 2 +Vout

Pin 3 +Vout

Pin 4 -Vout

Pin 5 -Vout

Pin 6 -Vout

Mounting holes marked with

must be connected to safety earth

Mates with JST housing

VHR-6N and JST Series

SVH-21T-P1.1 crimp terminals

-10

-20 010 20 30 40 50 60 70

100

Ambient Temperature (ºC)

Output Power (%)

1. All dimensions shown in inches (mm).

Tolerance: ±0.02 (0.5)

2. Weight: 0.42 lbs (190 g) approx.

Mates with JST housing

VHR-3N and JST Series

SVH-21T-P1.1 crimp terminals

TB3 - Fan Connector

Pin 1 Fan +

Pin 2 Fan -

Mates with Molex housing

22-01-1022 and 2759 crimp

terminals

Derating Curve

4.00 (101.6)

3.75 (95.2)

1.75

(44.45)

TB3

TB2

TB1

Voltage Adj.

2.00

(50.8)

0.10 (2.5)

1.16

(29.5)

0.06 (1.6)

0.134 (3.4)