ACDC 150 Watts ECP Series xppower.com * 100 W Convectioncooled * 150 W Forcedcooled * 2" x 4" Foot Print * Single Outputs from 12 V to 48 V * Builtin Fan Supply * <0.5 W No Load Input Power * 3 Year Warranty Specification Input General * 90-264 VAC (120-370 VDC), Derate from 100% load at 100 VAC to 90% load at 90 VAC Input Frequency * 47-63 Hz Input Current * 1.5 A max at 115 VAC, 0.75 A max at 230 VAC Inrush Current * 60 A max at 230 VAC, cold start at 25 C Power Factor * >0.95 at full load, 230 VAC Earth Leakage Current * 230 A at 264 VAC, 60 Hz. No Load Input Power * <0.5 W Input Protection * Internal T3.15A/250VAC fitted in line and neutral Input Voltage Output Output Voltage Output Voltage Trim Initial Set Accuracy Minimum Load Start Up Delay Start Up Rise Time Hold Up Time Line Regulation Load Regulation Transient Response * * * * * * * * * * Ripple & Noise * Overvoltage Protection * Overload Protection Short Circuit Protection Temperature Coefficient Fan Supply * * * See tables 10% 1% at 50 % load No minimum load requirement 550 ms typical 35 ms typical 16 ms minimum at full load and 115 VAC 0.5% max 0.5% max 4% maximum deviation, recovering to less than 1% within 500 s for 25% step load 1% max pk-pk, 20 MHz bandwidth, (see note 2) 115% - 140% of nominal voltage on main output. Recycle mains to reset. 110-150% Trip and restart (hiccup) 0.02%/C Efficiency Isolation Protection Level Switching Frequency MTBF * See table * 4000 VAC Input to Output 1500 VAC Input to Ground 500 VDC Output to Ground * Primary to Secondary: 2 MOPP Primary to Earth: 1 MOPP * 60 kHz 10 kHz * 300 kHrs to MIL-HDBK-217F at 25 C, GB Environmental Operating Temperature * -20 C to +70 C derate from 100% load at 50 C to 50% load at 70 C Cooling * Convection cooled: 100 W Forced cooled: 150 W with 10 CFM Operating Humidity * 5% to 90% RH, non condensing Operating Altitude * 3000 m Storage Temperature * -40 C to +85 C Shock * IEC68-2-6, 30 g, 11 mins half sine, 3 times in each of 6 axes Vibration * IEC68-2-27, 10-55 Hz, 2 g 10 mins / sweep. 60 mins for each of 3 axes EMC & Safety Emissions Harmonic Currents Voltage Flicker ESD Immunity Radiated Immunity EFT/Burst Surge Conducted Immunity Dips & Interruptions * 12 V at 500 mA Safety Approvals * EN55022/11, Level B conducted & Level A radiated * EN61000-3-2 Class A EN61000-3-2 Class C for load >60 W * EN61000-3-3 * EN61000-4-2, 8 kV air, 4 kV contact, Perf Criteria A * EN61000-4-3, 10 V/m, Perf Criteria A * EN61000-4-4, level 3, Perf Criteria A * EN61000-4-5, installation class 3, Perf Criteria A * EN61000-4-6, 10 V, Perf Criteria A * EN55024, 100% 10 ms, 30%, 500 ms, 100%, 5000 ms Perf Criteria A, A, B for high line, A, B, B for low line at full load, EN60601-1-2, 30% 500 ms, 60% 100 ms, 100% 10 ms, 100% 5000 ms, Perf Criteria A, A, A, B for high line, A, B, A, B for low line at full load * UL60950-1, IEC60950-1, EN60950-1, ANSI/AAMI ES 60601-1, IEC60601-1, EN60601-1 Output Current Convection-cooled Forced-cooled(1) Ripple and Noise pk-pk(2) Fan Output Efficiency(3) 12.0 V 8.33 A 12.50 A 120 mV 12 V/0.5 A 91% ECP150PS12 15.0 V 6.67 A 10.00 A 150 mV 12 V/0.5 A 91% ECP150PS15 24.0 V 4.17 A 6.25 A 240 mV 12 V/0.5 A 91% ECP150PS24 28.0 V 3.50 A 5.40 A 280 mV 12 V/0.5 A 92% ECP150PS28 48.0 V 2.08 A 3.10 A 480 mV 12 V/0.5 A 92% ECP150PS48 Output Voltage Model Number Notes 3. Minimum average efficiencies measured at 25%, 50%, 75% & 100% of 150 W load and 230 VAC input. 1. Requires 10 CFM. 2. Measured with 20 MHz bandwidth and 10 F electrolytic capacitor in parallel with 0.1 F ceramic capacitor Mechanical Details TB1 - Input Connector Pin 1 Line Pin 2 Not Fitted Pin 3 Neutral 4.00 (101.6) Voltage Adj. 3.75 (95.2) Mates with JST housing VHR-3N and JST Series SVH-21T-P1.1 crimp terminals 1 Mounting holes marked with must be connected to safety earth 1.75 (44.45) TB1 N 3 L 1 TB2 TB2 - Output Connector Pin 1 +Vout Pin 2 +Vout Pin 3 +Vout Pin 4 -Vout Pin 5 -Vout Pin 6 -Vout TB3 1 2.00 (50.8) 6 0.134 (3.4) Mates with JST housing VHR-6N and JST Series SVH-21T-P1.1 crimp terminals 1.16 (29.5) TB3 - Fan Connector Pin 1 Fan + Pin 2 Fan - Mates with Molex housing 22-01-1022 and 2759 crimp terminals 0.06 (1.6) 0.10 (2.5) Notes 1. All dimensions shown in inches (mm). Tolerance: 0.02 (0.5) 2. Weight: 0.42 lbs (190 g) approx. Derating Curve Output Power (%) 100 80 60 40 20 0 -20 -10 0 10 20 30 40 50 60 70 80 Ambient Temperature (C) 30-Sept-13 ACDC ECP150 Models and Ratings