UPD70F3380ZM2GJA-GAE-AX - RENESAS TECHNOLOGY

Data Sheet

V850ES/FJ3

32-bit Single-Chip Microcontroller

Hardware

µPD70F3378(A) µPD70F3379(A) µPD70F3380(A)

µPD70F3378(A1) µPD70F3379(A1) µPD70F3380(A1)

µPD70F3378(A2) µPD70F3379(A2) µPD70F3380(A2)

µPD70F3381(A) µPD70F3382(A)

µPD70F3381(A1) µPD70F3382(A1)

µPD70F3381(A2) µPD70F3382(A2)

Document No. U18567EE1V3DS00

Date Published March 2008

Printed in Germany

Data Sheet U18567EE1V3DS00

Removed ’Target Specification’ for (A)- and (A1)-Grade Devices in the

V850ES/FJ3

Notes for CMOS Devices

1. Precaution against ESD for semiconductors

Strong electric field, when exposed to a MOS device, can cause destruction of the gate oxide and

ultimately degrade the device operation. Steps must be taken to stop generation of static electricity

as much as possible, and quickly dissipate it once, when it has occurred. Environmental control

must be adequate. When it is dry, humidifier should be used. It is recommended to avoid using

insulators that easily build static electricity. Semiconductor devices must be stored and transported

in an anti-static container, static shielding bag or conductive material. All test and measurement

tools including work bench and floor should be grounded. The operator should be grounded using

wrist strap. Semiconductor devices must not be touched with bare hands. Similar precautions need

to be taken for PW boards with semiconductor devices on it.

2. Handling of unused input pins for CMOS

No connection for CMOS device inputs can be cause of malfunction. If no connection is provided to

the input pins, it is possible that an internal input level may be generated due to noise, etc., hence

causing malfunction. CMOS devices behave differently than Bipolar or NMOS devices. Input levels

of CMOS devices must be fixed high or low by using a pull-up or pull-down circuitry. Each unused

pin should be connected to VDD or GND with a resistor, if it is considered to have a possibility of

being an output pin. All handling related to the unused pins must be judged device by device and

related specifications governing the devices.

3. Status before initialization of MOS devices

Power-on does not necessarily define initial status of MOS device. Production process of MOS

does not define the initial operation status of the device. Immediately after the power source is

turned ON, the devices with reset function have not yet been initialized. Hence, power-on does not

guarantee out-pin levels, I/O settings or contents of registers. Device is not initialized until the reset

signal is received. Reset operation must be executed immediately after power-on for devices

having reset function.

4Data Sheet U18567EE1V3DS00

V850ES/FJ3

Legal Notes

• The information in this document is current as of January 2007. The information is subject to change

without notice. For actual design-in, refer to the latest publications of NEC Electronics data sheets or

data books, etc., for the most up-to-date specifications of NEC Electronics products. Not all products

and/or types are available in every country. Please check with an NEC sales representative for

availability and additional information.

• No part of this document may be copied or reproduced in any form or by any means without prior

written consent of NEC Electronics. NEC Electronics assumes no responsibility for any errors that

may appear in this document.

• NEC Electronics does not assume any liability for infringement of patents, copyrights or other

intellectual property rights of third parties by or arising from the use of NEC Electronics products

listed in this document or any other liability arising from the use of such NEC Electronics products.

No license, express, implied or otherwise, is granted under any patents, copyrights or other intellectual

property rights of NEC Electronics or others.

• Descriptions of circuits, software and other related information in this document are provided for

illustrative purposes in semiconductor product operation and application examples. The incorporation

of these circuits, software and information in the design of customer's equipment shall be done under

the full responsibility of customer. NEC Electronics assumes no responsibility for any losses incurred

by customers or third parties arising from the use of these circuits, software and information.

• While NEC Electronics endeavors to enhance the quality, reliability and safety of NEC Electronics

products, customers agree and acknowledge that the possibility of defects thereof cannot be eliminated

entirely. To minimize risks of damage to property or injury (including death) to persons arising from

defects in NEC Electronics products, customers must incorporate sufficient safety measures in their

design, such as redundancy, fire-containment and anti-failure features.

• NEC Electronics products are classified into the following three quality grades: “Standard”, “Special”

and “Specific”.

The "Specific" quality grade applies only to NEC Electronics products developed based on a

customer-designated “quality assurance program” for a specific application. The recommended

applications of NEC Electronics product depend on its quality grade, as indicated below. Customers

must check the quality grade of each NEC Electronics product before using it in a particular

application.

"Standard": Computers, office equipment, communications equipment, test and

measurement equipment, audio and visual equipment, home electronic

appliances, machine tools, personal electronic equipment and industrial robots.

"Special": Transportation equipment (automobiles, trains, ships, etc.), traffic control

systems, anti-disaster systems, anti-crime systems, safety equipment and

medical equipment (not specifically designed for life support).

"Specific": Aircraft, aerospace equipment, submersible repeaters, nuclear reactor control

systems, life support systems and medical equipment for life support, etc.

The quality grade of NEC Electronics products is “Standard” unless otherwise expressly specified in

NEC Electronics data sheets or data books, etc. If customers wish to use NEC Electronics products

in applications not intended by NEC Electronics, they must contact NEC Electronics sales

representative in advance to determine NEC Electronics 's willingness to support a given application.

Notes: 1. "NEC Electronics" as used in this statement means NEC Electronics Corporation and also

includes its majority-owned subsidiaries.

2. "NEC Electronics products" means any product developed or manufactured by or for NEC

Electronics (as defined above).

3. SuperFlash® is a registered trademark of Silicon Storage Technology, Inc. in several coun-

tries including the United States and Japan. This product uses SuperFlash® technology

licensed from Silicon Storage Technology, Inc.

Removed ’Target Specification’ for (A)- and (A1)-Grade Devices in the

V850ES/FJ3

Regional Information

Some information contained in this document may vary from country to country. Before using any NEC

product in your application, please contact the NEC office in your country to obtain a list of authorized

representatives and distributors. They will verify:

• Device availability

• Ordering information

• Product release schedule

• Availability of related technical literature

• Development environment specifications (for example, specifications for third-party tools and

components, host computers, power plugs, AC supply voltages, and so forth)

• Network requirements

In addition, trademarks, registered trademarks, export restrictions, and other legal issues may also vary

from country to country.

6Data Sheet U18567EE1V3DS00

V850ES/FJ3

NEC Electronics Corporation

1753, Shimonumabe, Nakahara-ku,

Kawasaki, Kanagawa 211-8668,

Japan

Tel: 044-435-5111

http://www.necel.com/

[America]

NEC Electronics America, Inc.

2880 Scott Blvd.

Santa Clara, CA 95050-2554, U.S.A.

Tel: 408-588-6000

800-366-9782

http://www.am.necel.com/

[Asia & Oceania]

NEC Electronics (China) Co., Ltd

7th Floor, Quantum Plaza, No. 27 ZhiChunLu Haidian

District, Beijing 100083, P.R.China

TEL: 010-8235-1155

http://www.cn.necel.com/

NEC Electronics Shanghai Ltd.

Room 2509-2510, Bank of China Tower,

200 Yincheng Road Central,

Pudong New Area, Shanghai P.R. China P.C:200120

Tel: 021-5888-5400

http://www.cn.necel.com/

NEC Electronics Hong Kong Ltd.

12/F., Cityplaza 4,

12 Taikoo Wan Road, Hong Kong

Tel: 2886-9318

http://www.hk.necel.com/

Seoul Branch

11F., Samik Lavied’or Bldg., 720-2,

Yeoksam-Dong, Kangnam-Ku,

Seoul, 135-080, Korea

Tel: 02-558-3737

NEC Electronics Taiwan Ltd.

7F, No. 363 Fu Shing North Road

Taipei, Taiwan, R. O. C.

Tel: 02-8175-9600

NEC Electronics Singapore Pte. Ltd.

238A Thomson Road,

#12-08 Novena Square,

Singapore 307684

Tel: 6253-8311

http://www.sg.necel.com/

For further information,

please contact:

G06.6-1A

[Europe]

NEC Electronics (Europe) GmbH

Arcadiastrasse 10

40472 Düsseldorf, Germany

Tel: 0211-65030

http://www.eu.necel.com/

Hanover Office

Podbielski Strasse 166 B

30177 Hanover

Tel: 0 511 33 40 2-0

Munich Office

Werner-Eckert-Strasse 9

81829 München

Tel: 0 89 92 10 03-0

Stuttgart Office

Industriestrasse 3

70565 Stuttgart

Tel: 0 711 99 01 0-0

United Kingdom Branch

Cygnus House, Sunrise Parkway

Linford Wood, Milton Keynes

MK14 6NP, U.K.

Tel: 01908-691-133

Succursale Française

9, rue Paul Dautier, B.P. 52180

78142 Velizy-Villacoublay Cédex

France

Tel: 01-3067-5800

Sucursal en España

Juan Esplandiu, 15

28007 Madrid, Spain

Tel: 091-504-2787

Tyskland Filial

Täby Centrum

Entrance S (7th floor)

18322 Täby, Sweden

Tel: 08 638 72 00

Filiale Italiana

Via Fabio Filzi, 25/A

20124 Milano, Italy

Tel: 02-667541

Branch The Netherlands

Steijgerweg 6

5616 HS Eindhoven

The Netherlands

Tel: 040 265 40 10

7
Data Sheet U18567EE1V3DS00
V850ES/FJ3
Table of Contents
Pin Group Information  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  11
1 Device package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2 Pin Groups 1x: Pins supplied by EVDD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
3 Pin Groups 2x: Pins supplied by EVDD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4 Pin Groups 3x: Pins supplied by BVDD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
5 Pin Groups 4: Pins supplied by AVREF0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
6 Pin Groups 5: Pins supplied by AVREF1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
7 Pin Groups 6: Pins supplied by EVDD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
8 Pin Groups 7: Pins supplied by VRO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Electrical Specifications of (A)-Grade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  13
1 Absolute Maximum Ratings  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2 Capacities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3 Operating condition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4 Voltage Regulator Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
5 Clock Generator Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
5.1 Main System Clock Oscillation Circuit Characteristics  . . . . . . . . . . . . . . . . . . . . . . . . 15
5.2 Sub System Clock Oscillation Circuit Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . 16
5.3 Internal-OSC Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5.4 PLL Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
5.5 SSCG Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
6 DC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
6.1 Input/Output Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
6.2 PIN leakage current. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
6.3 Power supply current (A-grade)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
6.3.1 µPD70F3378 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
6.3.2 µPD70F3379, µPD70F3380  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
6.3.3 µPD70F3381, µPD70F3382  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
7 AC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
7.1 CLKOUT Output Timing  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
7.2 Bus Timing (Multiplexed bus mode)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
7.3 RESET, Interrupt, ADTRG Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
7.4 Key Return Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
7.5 Timer Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
7.6 CSI Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
7.7 UART Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
7.8 IIC Timing  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
7.9 CAN Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
8 A/D Converter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
9 POC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
10 LVI  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
11 RAM Retention Flag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
12 Data Retention Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
13 Flash Memory Programming Characteristics  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Electrical Specifications of (A1)-Grade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  45
1 Absolute Maximum Ratings  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
2 Capacities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
3 Operating condition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
4 Voltage Regulator Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
5 Clock Generator Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
5.1 Main System Clock Oscillation Circuit Characteristics  . . . . . . . . . . . . . . . . . . . . . . . . 46
5.2 Sub System Clock Oscillation Circuit Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . 46

8Data Sheet U18567EE1V3DS00
V850ES/FJ3
Table of Contents
5.3 Internal-OSC Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
5.4 PLL Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
5.5 SSCG Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
6 DC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
6.1 Input/Output Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
6.2 PIN leakage current. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
6.3 Power supply current (A1-grade). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
6.3.1 µPD70F3378 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
6.3.2 µPD70F3379, µPD70F3380  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
6.3.3 µPD70F3381, µPD70F3382  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
7 AC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
7.1 CLKOUT Output Timing  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
7.2 Bus Timing (Multiplexed bus mode)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
7.3 RESET, Interrupt, ADTRG Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
7.4 Key Return Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
7.5 Timer Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
7.6 CSI Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
7.7 UART Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
7.8 IIC Timing  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
7.9 CAN Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
8 A/D Converter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
9 POC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
10 LVI  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
11 RAM Retention Flag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
12 Data Retention Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
13 Flash Memory Programming Characteristics  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Electrical Specifications of (A2)-Grade. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  59
1 Absolute Maximum Ratings  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
2 Capacities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
3 Operating condition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
4 Voltage Regulator Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
5 Clock Generator Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
5.1 Main System Clock Oscillation Circuit Characteristics  . . . . . . . . . . . . . . . . . . . . . . . . 60
5.2 Sub System Clock Oscillation Circuit Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . 61
5.3 Internal-OSC Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
5.4 PLL Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
5.5 SSCG Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
6 DC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
6.1 Input/Output Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
6.2 PIN leakage current. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
6.3 Power supply current (A2-grade). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
6.3.1 µPD70F3378 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
6.3.2 µPD70F3379, µPD70F3380  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
6.3.3 µPD70F3381, µPD70F3382  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
7 AC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
7.1 CLKOUT Output Timing  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
7.2 Bus Timing (Multiplexed bus mode)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
7.3 RESET, Interrupt, ADTRG Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
7.4 Key Return Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
7.5 Timer Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73
7.6 CSI Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
7.7 UART Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

9
Data Sheet U18567EE1V3DS00
V850ES/FJ3
Table of Contents
7.8 IIC Timing  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
7.9 CAN Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73
8 A/D Converter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74
9 POC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
10 LVI  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
11 RAM Retention Flag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
12 Data Retention Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
13 Flash Memory Programming Characteristics  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  77
1 Package Dimension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
2 Product Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
2.1 Marking of pin 1 at a QFP (Quad Flat Package) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
2.2 Identification of Lead-Free Products . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Change History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  81

10 Data Sheet U18567EE1V3DS00

V850ES/FJ3

Table of Contents

Data Sheet U18567EE1V3DS00

V850ES/FJ3

1. Pin Group Information

1.1 Device package information

The V850ES/Fx3 device series comprises several members. An overview with the pin and package

information is given in the following table:

This document describes the specification for the V850ES/FJ3.

1.2 Pin Groups 1x: Pins supplied by EVDD

1B: (SHMT1)

- P04, P30-31, P34; P40, P91, P913-915 (FE3)

- P04, P30-31, P34; P38-39, P40, P91, P913-915 (FF3)

- P04, P30-31, P34; P36-39, P40, P91, P911, P913-915 (FG3)

- P04, P30-31, P34; P36-39, P40, P63-69, P614-615, P80-81, P91, P911, P913-915 (FJ3)

- P04, P30-31, P34; P36-39, P40, P63-69, P614-615, P80-81, P91, P911, P913-915, P156-157

(FK3)

1D: (SHMT3)

- P00-03, P05-P06, P32-33, P35, P41-42, P50-55, P90, P96-99 (FE3)

- P00-03, P05-P06, P32-33, P35, P41-42, P50-55, P90, P96-99 (FF3)

- P00-03, P05-P06, P10-11, P32-33, P35, P41-42, P50-55, P90, P92-910, P912 (FG3)

- P00-03, P05-P06, P10-11, P32-33, P35, P41-42, P50-55, P60-62, P610-613, P90, P92-910,

P912 (FJ3)

- P00-03, P05-P06, P10-11, P32-33, P35, P41-42, P50-55, P60-62, P610-613, P90, P92-910,

P912, P150-155 (FK3)

1.3 Pin Groups 2x: Pins supplied by EVDD

2A: (CMOS)

- PCM0-1 (FE3)

- PCM0-3, PCS0-1, PCT0-1, PCT4, PCT6 (FF3)

2D: (SHMT3)

- PDL0-7 (FE3)

- PDL0-11 (FF3)

Series Member # Pins Device package information

μPD70F3370A

μPD70F3371 64 FE3

μPD70F3372

μPD70F3373 80 FF3

μPD70F3374

μPD70F3375

μPD70F3376A

μPD70F3377A

100 FG3

μPD70F3378

μPD70F3379

μPD70F3380

μPD70F3381

μPD70F3382

144 FJ3

μPD70F3383

μPD70F3384

μPD70F3385

176 FK3

12 Data Sheet U18567EE1V3DS00

V850ES/FJ3

1.4 Pin Groups 3x: Pins supplied by BVDD

3A: (CMOS)

- PCM0-3, PCS0-1, PCT0-1, PCT4, PCT6 (FG3)

- PCD0-3, PCM0-5, PCS0-7, PCT0-7 (FJ3 + FK3)

3D: (SHMT3)

- PDL0-13 (FG3)

- PDL0-15 (FJ3 + FK3)

1.5 Pin Groups 4: Pins supplied by AVREF0

4: (CMOS)

- P70-79 (FE3)

-P70-711 (FF3)

- P70-715 (FG3)

- P70-715, P120-127 (FJ3 + FK3)

1.6 Pin Groups 5: Pins supplied by AVREF1

- P20-P215 (FK3) (CMOS)

1.7 Pin Groups 6: Pins supplied by EVDD

- RESET (SHMT2)

-IC, FLMD0

1.8 Pin Groups 7: Pins supplied by VRO

- X1, X2, XT1, XT2

Data Sheet U18567EE1V3DS00

V850ES/FJ3

2. Electrical Specifications of (A)-Grade

This product has to be used only under the conditions of VDD=EVDD=BVDD. Operation is not ensured

at the time of using this product except this condition.

2.1 Absolute Maximum Ratings

Absolute Maximum Ratings (Ta=25°C)

Remarks: 1. The characteristics of the dual-function pins are the same as those of the port pins

unless otherwise specified

Notes: 1. Be sure not to exceed the absolute maximum ratings (Max. value) of each supply voltage.

2. Excluding ADC IAREF0 current.

2.2 Capacities

(Ta = 25°C, VDD = EVDD = BVDD = AVREF0 = VSS = EVSS = BVSS = AVSS = 0V)

Parameter Symbol Conditions Rating Unit

Supply voltage

VDD VDD=EVDD=BVDD, -0.5 to +6.5 V

EVDD VDD=EVDD=BVDD -0.5 to +6.5 V

BVDD VDD=EVDD=BVDD -0.5 to +6.5 V

AVREF0 -0.5 to +6.5 V

VSS VSS=EVSS=BVSS=AVSS -0.5 to +0.5 V

EVSS VSS=EVSS=BVSS=AVSS -0.5 to +0.5 V

BVSS VSS=EVSS=BVSS=AVSS -0.5 to +0.5 V

AVSS VSS=EVSS=BVSS=AVSS -0.5 to +0.5 V

Input voltage

VI1 Pin Group 1x, 6 -0.5 to EVDD+0.5

Note1 V

VI2 Pin Group 3x -0.5 to BVDD+0.5

Note1 V

VI3 Pin Group 7 -0.5 to VRO+0.5

Note1 V

Analog input voltage VIAN Pin Group 4 -0.5 to AVREF0+0.5

Note1 V

High level output cur-

rent IOH

Pin Group 1x 1 pin -4 mA

Total - 5 0 mA

Pin Group 3x 1 pin -4 mA

Total - 5 0 mA

Pin Group 4 1 pin -4 mA

Total - 2 0Note2 mA

Low level output current IOL

Pin Group 1x 1 pin 4 mA

Total 5 0 m A

Pin Group 3x 1 pin 4 mA

Total 5 0 m A

Pin Group 4 1 pin 4 mA

Total 2 0 Note2 mA

Operating ambient

temperature Ta Normal operating mode -40 to +85 °C

Flash programming mode -40 to +85

Storage temperature Tstg -40 to +125 °C

Parameter Symbol Conditions MIN. TYP. MAX. Unit

Input/output capacitance CIO f=1MHz, Not measured pins is 0V. 10 pF

14 Data Sheet U18567EE1V3DS00

V850ES/FJ3

2.3 Operating condition

(Ta = -40 to +85°C, C=4.7uF, VDD = EVDD = BVDD = 3.3 to 5.5V, AVREF0 = 3.3 to 5.5V, VSS = EVSS = BVSS = AVSS = 0V)

Notes: 1. For using SSCG please refer to ’2.5.5 SSCG Characteristics’ for details

2. VDD = EVDD = BVDD

3. RC Oscillation frequency is min. 25kHz max. 55kHz. This clock is divided by 2 internally.

Internal System clock frequency (fVBCLK)Supply voltage Operating Condition

4.0≤fxx≤32MHz (≤256KB product)

4.0≤fxx≤48MHz (≥384KB product)

Note1

4.0V≤VDD≤5.5VNote2

Operation of functions is usable under following

conditions:

•Peripheral clock frequency

•fXP1 ≤ 32MHz

•fXP2 ≤ 32MHz

•AC characteristics:

•Refer to chapter ’2.7 AC Characteris-

tics’ for details.

3.5V≤VDD<4.0VNote2

Operation of functions is usable under following

conditions:

•Peripheral clock frequency

•fXP1 ≤ 20MHz

•fXP2 ≤ 20MHz

•AC characteristics:

•Refer to chapter ’2.7 AC Characteris-

tics’ for details.

3.3V≤VDD<3.5VNote2

Only operation of the following functions is

assured:

•CPU

•Flash (include programming)

•RAM

•IO Buffer

•Port

•WT

•WDT

•INT

•CLM

•POC

•LVI

3.3V≤AVREF0≤5.5V

•A/D Converter

•Refer to chapter ’2.8 A/D Converter’ for

details.

•stop ADC for AVREF0 < 4.0V

(ADA0CE bit =0)

32kHz≤fXT≤35kHz (Crystal)

3.3V≤VDD<5.5VNote2 -

12.5kHz≤fXT≤27.5kHz Note3(RC)

fRL (240kHz Internal-OSC) 3.3V≤VDD<5.5VNote2 -

Data Sheet U18567EE1V3DS00

V850ES/FJ3

2.4 Voltage Regulator Characteristics

(Ta = -40 to +85°C, C=4.7uF, VDD = EVDD = BVDD, VSS = EVSS = BVSS = AVSS = 0V))

Note: In case of non-POC device, be sure to start VDD in the state of RESET=VSS=0V.

For POC devices there is no need to control external RESET terminal. For decives with POC

function the internal RESET signal will automatically controlled until VRO is stable.

2.5 Clock Generator Circuit

2.5.1 Main System Clock Oscillation Circuit Characteristics

(Ta = -40 to +85°C, C=4.7uF, VDD = EVDD = BVDD = 3.3 to 5.5V, AVREF0 = 3.3 to 5.5V, VSS = EVSS = BVSS = AVSS = 0V)

Notes: 1. Indicates only oscillation circuit characteristics. Refer to ’2.7 AC Characteristics’ for CPU

operation clock.

2. Time required to stabilize oscillation after VDD reaches oscillator voltage range MIN. 3.3V

3. Depends on the setting of the oscillation stabilization time select register (OSTS)

4. Minimum time required to stabilize flash. Time has to be secured by setting the oscillation

stabilization time select register (OSTS)

Parameter Symbol Conditions MIN. TYP. MAX. Unit

Input voltage VDD 3.5 5.5 V

Limited function see ’2.3 Operating condition’ 3.3 V

Output voltage VRO 2.5 V

Output voltage

stabilization time tREGNote After VDD reaches voltage range min. 3.3V

To connect C=4.7uF on REGC terminal 1ms

Resonator Recommended Circuit Parameter Conditions MIN. TYP. MAX. Unit

Crystal /

Ceramic resona-

tor

Refer to figure below

Oscillator fre-

quency (fx)Note1 416MHz

Oscillation stabili-

zation time Note2

After STOP mode 64Note4 Note3 μs

After IDLE2 mode 54Note4 Note3 μs

VDD

tREG

VRO

RESET

X1 X2

16 Data Sheet U18567EE1V3DS00

V850ES/FJ3

2.5.2 Sub System Clock Oscillation Circuit Characteristics

(Ta = -40 to +85°C, C=4.7uF, VDD = EVDD = BVDD = 3.3 to 5.5V, AVREF0 = 3.3 to 5.5V, VSS = EVSS = BVSS = AVSS = 0V)

Notes: 1. Indicates only oscillation circuit characteristics. Refer to "AC Characteristic" for cpu opera-

tion clock.

2. Time required to stabilize oscillation after VDD reaches oscillator voltage range min. 3.3V

3. In order to avoid the influence of wiring capacity, shorten wiring as much as possible.

4. RC Oscillation frequency is typ. 40kHz. This clock is divided by 2 internally. In case of RC

Oscillator, internal system clock frequency (fxt) is min. 12.5kHz, typ. 20kHz, max. 27.5kHz.

2.5.3 Internal-OSC Characteristics

(Ta = -40 to +85°C, C=4.7uF, VDD = EVDD = BVDD = 3.3 to 5.5V, AVREF0 = 3.3 to 5.5V, VSS = EVSS = BVSS = AVSS = 0V)

Resonator Recommended Circuit Parameter Conditions MIN. TYP. MAX. Unit

Crystal

resonator Refer to Figure 1

Oscillator fre-

quency (fxt)Note1 32 32.768 35 kHz

Oscillation stabiliza-

tion time Note2 10 s

resonator Refer to Figure 2

Oscillator

frequencyNote1,4

R=390KΩ ±5% Note3,

C=47pF±10% Note3 25 40 55 kHz

Oscillation stabiliza-

tion time Note2 100 μs

Parameter Symbol Conditions MIN. TYP. MAX. Unit

Output

frequency

fRL 240kHz Internal-OSC 204 240 276 kHz

fRH 8MHz Internal-OSC 7.2 8.0 8.8 MHz

Oscillation

stabilization

time

240kHz Internal-OSC 10 36 µs

8MHz Internal-OSC 51 92 256 µs

XT1 XT2 XT1 XT2

Data Sheet U18567EE1V3DS00

V850ES/FJ3

2.5.4 PLL Characteristics

(Ta = -40 to +85°C, C=4.7uF, VDD = EVDD = BVDD = 3.3 to 5.5V, AVREF0 = 3.3 to 5.5V, VSS = EVSS = BVSS = AVSS = 0V)

Notes: 1. The input of the PLL (fPLLI) can be set to fX, fX/2, or fX/4. The divider is set through an option

byte in the code flash memory.

2. Not tested in production.

2.5.5 SSCG Characteristics

(Ta = -40 to +85°C, C=4.7uF, VDD = EVDD = BVDD = 3.3 to 5.5V, AVREF0 = 3.3 to 5.5V, VSS = EVSS = BVSS = AVSS = 0V)

Remark: The SSCG MAX output frequency indicates the case without modulation. If modulation is

enabled the average SSCG frequency has to be set lower. The maximum achievable aver-

age operating frequency with modulation is as follows:

Parameter Symbol Conditions MIN. TYP. MAX. Unit

Input frequency fx 4 16 MHz

fPLLI Note1 36MHz

Output frequency fxx ≤256KB product 12 32 MHz

≥384KB product 12 48

Lock time tPLL After VDD reaches voltage range min. 3.3V 800 μs

Output period jitter

Note2 tpj Peak to peak 2.0 ns

Parameter Symbol Conditions MIN. TYP. MAX. Unit

Input frequency fx 4 16 MHz

Output frequency fXX

≤256KB product 12 32 MHz

≥384KB product 12 48

Lock time tSSCG After VDD reaches voltage range min. 3.3V 1000 μs

SSCG input clock divider selector

SFC1[6:4]

Percent modulation Maximum average operating fre-

quency Unit

TYP MAX ≤256KB product ≥384KB product

000B ± 0.5% ± 2.0% 31.4 47.0

MHz

001B ± 1.0% ± 2.5% 31.2 46.8

010B ± 2.0% ± 4.0% 30.7 46.1

011B ± 3.0% ± 6.0% 30.1 45.1

100B ± 4.0% ± 8.0% 29.4 44.2

101B ± 5.0% ± 10.0% 28.8 43.2

18 Data Sheet U18567EE1V3DS00

V850ES/FJ3

2.6 DC Characteristics

2.6.1 Input/Output Level

(Ta = -40 to +85°C, C=4.7uF, VDD = EVDD = BVDD = 3.3 to 5.5V, AVREF0 = 3.3 to 5.5V, VSS = EVSS = BVSS = AVSS = 0V)

Remark: The characteristics of the dual-function pins are the same as those of the port pins unless

otherwise specified.

Notes: 1. DRST terminal only. (Control register is OCDM)

2. Total IOH/IOL max is 20mA/-20mA each power supply line (EVDD,BVDD and AVREF0).

AVREF0 IOH/IOL current is excluding ADC current IAREF0.

3. Typical value. Not tested and guaranteed

Parameter Symbol Conditions MIN. TYP. MAX. Unit

High level

input voltage

VIH1 Pin Group 1B 0.7⋅EVDD EVDD V

VIH2 Pin Group 1D 0.8⋅EVDD EVDD V

Pin Group 3D 0.8⋅BVDD BVDD V

VIH3 Pin Group 3A 0.7⋅BVDD BVDD V

VIH4 Pin Group 4 0.7⋅AVREF0 AVREF0 V

VIH5 Pin Group 6 0.8⋅EVDD EVDD V

Low level

input voltage

VIL1 Pin Group 1B EVSS 0.3⋅EVDD V

VIL2 Pin Group 1D EVSS 0.4⋅EVDD V

Pin Group 3D BVSS 0.4⋅BVDD V

VIL3 Pin Group 3A BVSS 0.3⋅BVDD V

VIL4 Pin Group 4 AVSS 0.3⋅AVREF0 V

VIL5 Pin Group 6 EVSS 0.2⋅EVDD V

Input hysteresis

VHYS1 Pin Group 1B Center point at

0.5 x EVDD Note3 0.267 x EVDD - 0.51V V

VHYS2

Pin Group 1D Center point at

0.6 x EVDD Note3 0.192 x EVDD - 0.31V V

Pin Group 3D Center point at

0.6 x BVDD Note3 0.192 x BVDD - 0.31V V

VHYS5 Pin Group 6 Center point at

0.5 x EVDD Note3 0.535 x EVDD - 0.9V V

High level

output voltage

Note2

VOH1 Pin Group 1x IOH=-1.0mA EVDD-1.0 EVDD V

IOH=-100uA EVDD-0.5 EVDD V

VOH2 Pin Group 3x IOH=-1.0mA BVDD-1.0 BVDD

IOH=-100uA BVDD-0.5 BVDD V

VOH3 Pin Group 4 IOH=-1.0mA AVREF0-1.0 AVREF0 V

IOH=-100uA AVREF0-0.5 AVREF0 V

Low level output

voltageNote2

VOL1 Pin Group 1x IOL=1.0mA 00.4V

P914, 915 IOL=3.0mA

VOL2 Pin Group 3x IOL=1.0mA 0 0.4 V

VOL3 Pin Group 4 IOL=1.0mA 0 0.4 V

Software pull-up

resistor R1 VI=0V 10 30 100 kΩ

Software Note1

pull-down resistor R2 VI=VDD 10 30 100 kΩ

Data Sheet U18567EE1V3DS00

V850ES/FJ3

2.6.2 PIN leakage current

(Ta = -40 to +85°C, C=4.7uF, VDD = EVDD = BVDD = 3.3 to 5.5V, AVREF0 = 3.3 to 5.5V, VSS = EVSS = BVSS = AVSS = 0V)

Notes: 1. The input leakage current of FLMD0 is as follows:

High level input leakage current : 2.0uA

Low level input leakage current : -2.0uA

Parameter Symbol Conditions MIN. TYP. MAX. Unit

High level input

leakage current ILIH1 VI=VDD Analog pins 0.2

Other pins Note1 0.5

Low level input

leakage current ILIL1 VI=0V Analog pins -0.2

Other pins Note1 -0.5

High level output

leakage current ILOH1 VO=VDD Analog pins 0.2

Other pins 0.5

Low level output

leakage current ILOL1 VO=0V Analog pins -0.2

Other pins -0.5

20 Data Sheet U18567EE1V3DS00

V850ES/FJ3

2.6.3 Power supply current (A-grade)

2.6.3.1 µPD70F3378

(a) Absolute values

(Ta = -40 to +85°C, C=4.7uF,

VDD = EVDD = BVDD = 3.3 to 5.5V, AVREF0 = 3.3 to 5.5V, VSS = EVSS = BVSS = AVSS = 0VNote1)

Mode Symbol Condition TYP. MAX. Unit

Operating

mode

Note2,8

IDD1

All peripherals

running

Peripheral: fxx

PRSI option: 0

PLL: ON

12MHz≤fxx≤32MHz

fxx=20MHz

fx=5MHz 28 38 mA

fxx=32MHz

fx=16MHz 40 53 mA

PLL: OFF

4MHz≤fxx≤16MHz

fxx=8MHz

8MHz Internal-

OSC Note3

14 21 mA

fxx=16MHz

fx=16MHz 22 30 mA

Peripheral: fxx/2

PRSI option: 1

PLL: ON

12MHz≤fxx≤32MHz

fxx=32MHz

fx=16MHz 36 48 mA

All peripherals

stopped

Peripheral: fxx

PRSI option: 0

PLL: ON

12MHz≤fxx≤32MHz

fxx=20MHz

fx=5MHz 22 mA

fxx=32MHz

fx=16MHz 32 mA

PLL: OFF

4MHz≤fxx≤16MHz

fxx=8MHz

8MHz Internal-

OSC Note3

12 mA

fxx=16MHz

fx=16MHz 19 mA

Peripheral: fxx/2

PRSI option: 1

PLL: ON

12MHz≤fxx≤32MHz

fxx=32MHz

fx=16MHz 31 mA

HALT

mode

Note8

IDD2

All peripherals

running

Peripheral: fxx

PRSI option: 0

PLL: ON

12MHz≤fxx≤32MHz

fxx=20MHz

fx=5MHz 18 26 mA

fxx=32MHz

fx=16MHz 27 39 mA

PLL: OFF

4MHz≤fxx≤16MHz

fxx=8MHz

8MHz Internal-

OSC Note3

812mA

fxx=16MHz

fx=16MHz 13 20 mA

Peripheral: fxx/2

PRSI option: 1

PLL: ON

12MHz≤fxx≤32MHz

fxx=32MHz

fx=16MHz 21 29 mA

All peripherals

stopped

Peripheral: fxx

PRSI option: 0

PLL: ON

12MHz≤fxx≤32MHz

fxx=20MHz

fx=5MHz 12 mA

fxx=32MHz

fx=16MHz 18 mA

PLL: OFF

4MHz≤fxx≤16MHz

fxx=8MHz

8MHz Internal-

OSC Note3

5mA

fxx=16MHz

fx=16MHz 9mA

Peripheral: fxx/2

PRSI option: 1

PLL: ON

12MHz≤fxx≤32MHz

fxx=32MHz

fx=16MHz 18 mA

Data Sheet U18567EE1V3DS00

V850ES/FJ3

IDLE1

mode IDD3

Peripheral (TAA, UARTD) run-

ning

PLL: OFF

4MHz≤fxx≤16MHz

Note7

fxx=5MHz

fx=5MHz 1.7 2.4 mA

fxx=12MHz

fx=12MHz 2.7 3.9 mA

fxx=16MHz

fx=16MHz 3.3 4.7 mA

fxx=8MHz, 8MHz Internal-OSCNote3 1.5 2.3 mA

All peripherals stopped

PLL: OFF

4MHz≤fxx≤16MHz

Note7

fxx=5MHz

fx=5MHz 1.2 mA

fxx=12MHz

fx=12MHz 1.4 mA

fxx=16MHz

fx=16MHz 1.6 mA

fxx=8MHz, 8MHz Internal-OSCNote3 1.1 mA

IDLE2

mode IDD4

PLL: OFF

4MHz≤fxx≤16MHz

Note7

fxx=5MHz

fx=5MHz 0.4 0.7 mA

fxx=12MHz

fx=12MHz 0.7 1.0 mA

fxx=16MHz

fx=16MHz 0.8 1.2 mA

fxx=8MHz, 8MHz Internal-OSC Note3 0.2 0.5 mA

SUB

operating

modeNote5

IDD5

Crystal resonator (fxt = 32,768kHz) 80 400 μA

RC resonator (fxt=20kHz) Note6 80 400 µA

240 kHz Internal-OSC (SubOSC stopped) 220 1000 µA

SubIDLE

mode

Note3,5

IDD6

Crystal resonator (fxt = 32,768kHz) 20 190 μA

RC resonator (fxt=20kHz) Note6 40 220 μA

240kHz Internal-OSC (SubOSC stopped) 25 180 μA

STOP

mode

Note3,4

IDD7

POC stop 240kHz Internal-OSC stop 7.5 80 μA

240kHz Internal-OSC working 15.5 95 μA

POC work 240kHz Internal-OSC stop 10.5 85 μA

240kHz Internal-OSC working 18.5 100 μA

Mode Symbol Condition TYP. MAX. Unit

22 Data Sheet U18567EE1V3DS00

V850ES/FJ3

(b) Calculation formulas

(Ta = -40 to +85°C, C=4.7uF,

VDD = EVDD = BVDD = 3.3 to 5.5V, AVREF0 = 3.3 to 5.5V, VSS = EVSS = BVSS = AVSS = 0VNote1))

Notes: 1. VDD, EVDD and BVDD total current. (Ports are stopped).

AVREF0 current, port buffer current (including a current flowing in the on-chip pull-up/pull-

down resistor) are not included.

2. The code flash and the data flash are in read mode.

When the device is in programming mode (Self-programming mode or data flash program-

ming mode), the current value (MAX. value) adds by the following value:

•Self-programming mode:

+ In case of PLL OFF: 7-(0.33*fxx+0.1) [mA]

+ In case of PLL ON: 7-(0.18*fxx+3.0) [mA]

•Data flash programming mode:

+ 7-(0.18*fxx/4+3.0) [mA]

3. Main OSC is stopped.

4. Do not use SubOSC.

5. POC is working. 240kHz Internal-OSC is working. 8MHz Internal-OSC is stopped.

6. RC Oscillation frequency is typ.40kHz. This clock is divided by 2 internally.

7. 8MHz Internal-OSC is stopped

8. When the SSCG is running, the current value adds typ +2.5mA, max +4mA.

9. The formulas are for reference only. Not all possible values for fxx are tested in the outgoing

device inspection.

Mode Symbol Condition TYP. Note9 MAX. Note9 Unit

Operating

mode

Note2,8

IDD1

All peripherals

running

Peripheral: fxx

PRSI option: 0

PLL: ON

12MHz≤fxx≤32MHz 1.03⋅fxx+7.1 1.24⋅fxx+13.6 mA

PLL: OFF

4MHz≤fxx≤16MHz 1.03⋅fxx+5.5 1.24⋅fxx+10.6 mA

Peripheral: fxx/2

PRSI option: 1

PLL: ON

12MHz≤fxx≤32MHz 0.92⋅fxx+6.0 1.11⋅fxx+12.2 mA

All peripherals

stopped

Peripheral: ffxx-

PRSI option: 0

PLL: ON

12MHz≤fxx≤32MHz 0.81⋅fxx+6.2 mA

PLL: OFF

4MHz≤fxx≤16MHz 0.83⋅fxx+5.7 mA

Peripheral: fxx/2

PRSI option: 1

PLL: ON

12MHz≤fxx≤32MHz 0.79⋅fxx+6.2 mA

HALT

mode

Note8

IDD2

All peripherals

running

Peripheral: ffxx-

PRSI option: 0

PLL: ON

16MHz≤fxx≤32MHz 0.75⋅fxx+3.0 1.04*fxx+5.4 mA

PLL: OFF

4MHz≤fxx≤16MHz 0.70⋅fxx+1.9 1.00*fxx+4.0 mA

Peripheral: fxx/2

PRSI option: 1

PLL: ON

16MHz≤fxx≤32MHz 0.56⋅fxx+2.8 0.69*fxx+7.0 mA

All peripherals

stopped

Peripheral: fxx

PRSI option: 0

PLL: ON

16MHz≤fxx≤32MHz 0.46⋅fxx+2.8 mA

PLL: OFF

4MHz≤fxx≤16MHz 0.44⋅fxx+1.6 mA

Peripheral: fxx/2

PRSI option: 1

PLL: ON

16MHz≤fxx≤32MHz 0.46⋅fxx+1.8 mA

IDLE1

mode IDD3

Peripheral (TAA, UARTD) run-

ning

PLL: OFF

4MHz≤fxx≤16MHz

Note7

0.151⋅fxx+0.90 0.210⋅fxx+ 1.35 mA

All peripherals stopped 0.035⋅fxx+1.01 mA

IDLE2

mode IDD4 PLL: OFF

4MHz ≤fxx≤16MHz Note7 0.037⋅fxx+0.21 0.049⋅fxx+ 0.43 mA

Data Sheet U18567EE1V3DS00

V850ES/FJ3

2.6.3.2 µPD70F3379, µPD70F3380

(a) Absolute values

(Ta = -40 to +85°C, C=4.7uF,

VDD = EVDD = BVDD = 3.3 to 5.5V, AVREF0 = 3.3 to 5.5V, VSS = EVSS = BVSS = AVSS = 0VNote1)

Mode Symbol Condition TYP. MAX. Unit

Operating

mode

Note2,8

IDD1

All peripherals

running

Peripheral: fxx

PRSI option: 0

PLL: ON

12MHz≤fxx≤32MHz

fxx=20MHz

fx=5MHz 28 39 mA

fxx=32MHz

fx=16MHz 41 54 mA

PLL: OFF

4MHz≤fxx≤16MHz

fxx=8MHz

8MHz Internal-

OSC Note3

14 21 mA

fxx=16MHz

fx=16MHz 23 31 mA

Peripheral: fxx/2

PRSI option: 1

PLL: ON

12MHz≤fxx≤48MHz

fxx=48MHz

fx=12MHz 51 66 mA

All peripherals

stopped

Peripheral: fxx

PRSI option: 0

PLL: ON

12MHz≤fxx≤32MHz

fxx=20MHz

fx=5MHz 22 mA

fxx=32MHz

fx=16MHz 32 mA

PLL: OFF

4MHz≤fxx≤16MHz

fxx=8MHz

8MHz Internal-

OSC Note3

12 mA

fxx=16MHz

fx=16MHz 19 mA

Peripheral: fxx/2

PRSI option: 1

PLL: ON

12MHz≤fxx≤48MHz

fxx=48MHz

fx=12MHz 44 mA

HALT

mode

Note8

IDD2

All peripherals

running

Peripheral: fxx

PRSI option: 0

PLL: ON

12MHz≤fxx≤32MHz

fxx=20MHz

fx=5MHz 18 26 mA

fxx=32MHz

fx=16MHz 27 39 mA

PLL: OFF

4MHz≤fxx≤16MHz

fxx=8MHz

8MHz Internal-

OSC Note3

812mA

fxx=16MHz

fx=16MHz 13 20 mA

Peripheral: fxx/2

PRSI option: 1

PLL: ON

12MHz≤fxx≤48MHz

fxx=48MHz

fx=12MHz 30 40 mA

All peripherals

stopped

Peripheral: fxx

PRSI option: 0

PLL: ON

12MHz≤fxx≤32MHz

fxx=20MHz

fx=5MHz 12 mA

fxx=32MHz

fx=16MHz 18 mA

PLL: OFF

4MHz≤fxx≤16MHz

fxx=8MHz

8MHz Internal-

OSC Note3

5mA

fxx=16MHz

fx=16MHz 9mA

Peripheral: fxx/2

PRSI option: 1

PLL: ON

12MHz≤fxx≤48MHz

fxx=48MHz

fx=12MHz 24 mA

24 Data Sheet U18567EE1V3DS00

V850ES/FJ3

IDLE1

mode IDD3

Peripheral (TAA, UARTD) run-

ning

PLL: OFF

4MHz≤fxx≤16MHz

Note7

fxx=5MHz

fx=5MHz 1.7 2.4 mA

fxx=12MHz

fx=12MHz 2.7 3.9 mA

fxx=16MHz

fx=16MHz 3.3 4.7 mA

fxx=8MHz, 8MHz Internal-OSCNote3 1.5 2.3 mA

All peripherals stopped

PLL: OFF

4MHz≤fxx≤16MHz

Note7

fxx=5MHz

fx=5MHz 1.2 mA

fxx=12MHz

fx=12MHz 1.4 mA

fxx=16MHz

fx=16MHz 1.6 mA

fxx=8MHz, 8MHz Internal-OSCNote3 1.1 mA

IDLE2

mode IDD4

PLL: OFF

4MHz≤fxx≤16MHz

Note7

fxx=5MHz

fx=5MHz 0.4 0.7 mA

fxx=12MHz

fx=12MHz 0.7 1.0 mA

fxx=16MHz

fx=16MHz 0.8 1.2 mA

fxx=8MHz, 8MHz Internal-OSC Note3 0.2 0.5 mA

SUB

operating

modeNote5

IDD5

Crystal resonator (fxt = 32,768kHz) 80 400 μA

RC resonator (fxt=20kHz) Note6 80 400 µA

240 kHz Internal-OSC (SubOSC stopped) 220 1000 µA

SubIDLE

mode

Note3,5

IDD6

Crystal resonator (fxt = 32,768kHz) 20 190 μA

RC resonator (fxt=20kHz) Note6 40 220 μA

240kHz Internal-OSC (SubOSC stopped) 25 180 μA

STOP

mode

Note3,4

IDD7

POC stop 240kHz Internal-OSC stop 7.5 90 μA

240kHz Internal-OSC working 15.5 105 μA

POC work 240kHz Internal-OSC stop 10.5 95 μA

240kHz Internal-OSC working 18.5 110 μA

Mode Symbol Condition TYP. MAX. Unit

Data Sheet U18567EE1V3DS00

V850ES/FJ3

(b) Calculation formulas

(Ta = -40 to +85°C, C=4.7uF,

VDD = EVDD = BVDD = 3.3 to 5.5V, AVREF0 = 3.3 to 5.5V, VSS = EVSS = BVSS = AVSS = 0VNote1))

Notes: 1. VDD, EVDD and BVDD total current. (Ports are stopped).

AVREF0 current, port buffer current (including a current flowing in the on-chip pull-up/pull-

down resistor) are not included.

2. The code flash and the data flash are in read mode.

When the device is in programming mode (Self-programming mode or data flash program-

ming mode), the current value (MAX. value) adds by the following value:

•Self-programming mode:

+ In case of PLL OFF: 7-(0.33*fxx+0.1) [mA]

+ In case of PLL ON: 7-(0.18*fxx+3.0) [mA]

•Data flash programming mode:

+ 7-(0.18*fxx/4+3.0) [mA]

3. Main OSC is stopped.

4. Do not use SubOSC.

5. POC is working. 240kHz Internal-OSC is working. 8MHz Internal-OSC is stopped.

6. RC Oscillation frequency is typ.40kHz. This clock is divided by 2 internally.

7. 8MHz Internal-OSC is stopped

8. When the SSCG is running, the current value adds typ +2.5mA, max +4mA.

9. The formulas are for reference only. Not all possible values for fxx are tested in the outgoing

device inspection.

Mode Symbol Condition TYP. Note9 MAX. Note9 Unit

Operating

mode

Note2,8

IDD1

All peripherals

running

Peripheral: fxx

PRSI option: 0

PLL: ON

12MHz≤fxx≤32MHz 1.06⋅fxx+7.1 1.27⋅fxx+13.6 mA

PLL: OFF

4MHz≤fxx≤16MHz 1.06⋅fxx+5.5 1.28⋅fxx+10.6 mA

Peripheral: fxx/2

PRSI option: 1

PLL: ON

12MHz≤fxx≤48MHz 0.94⋅fxx+6.0 1.13⋅fxx+12.2 mA

All peripherals

stopped

Peripheral: ffxx-

PRSI option: 0

PLL: ON

12MHz≤fxx≤32MHz 0.81⋅fxx+6.2 mA

PLL: OFF

4MHz≤fxx≤16MHz 0.83⋅fxx+5.7 mA

Peripheral: fxx/2

PRSI option: 1

PLL: ON

12MHz≤fxx≤48MHz 0.79⋅fxx+6.2 mA

HALT

mode

Note8

IDD2

All peripherals

running

Peripheral: ffxx-

PRSI option: 0

PLL: ON

16MHz≤fxx≤32MHz 0.75⋅fxx+3.0 1.04*fxx+5.4 mA

PLL: OFF

4MHz≤fxx≤16MHz 0.70⋅fxx+1.9 1.00*fxx+4.0 mA

Peripheral: fxx/2

PRSI option: 1

PLL: ON

16MHz≤fxx≤48MHz 0.56⋅fxx+2.8 0.69*fxx+7.0 mA

All peripherals

stopped

Peripheral: fxx

PRSI option: 0

PLL: ON

16MHz≤fxx≤32MHz 0.46⋅fxx+2.8 mA

PLL: OFF

4MHz≤fxx≤16MHz 0.44⋅fxx+1.6 mA

Peripheral: fxx/2

PRSI option: 1

PLL: ON

16MHz≤fxx≤48MHz 0.46⋅fxx+1.8 mA

IDLE1

mode IDD3

Peripheral (TAA, UARTD) run-

ning

PLL: OFF

4MHz≤fxx≤16MHz

Note7

0.151⋅fxx+0.90 0.210⋅fxx+ 1.35 mA

All peripherals stopped 0.035⋅fxx+1.01 mA

IDLE2

mode IDD4 PLL: OFF

4MHz ≤fxx≤16MHz Note7 0.037⋅fxx+0.21 0.049⋅fxx+ 0.43 mA

26 Data Sheet U18567EE1V3DS00

V850ES/FJ3

2.6.3.3 µPD70F3381, µPD70F3382

(a) Absolute values

(Ta = -40 to +85°C, C=4.7uF,

VDD = EVDD = BVDD = 3.3 to 5.5V, AVREF0 = 3.3 to 5.5V, VSS = EVSS = BVSS = AVSS = 0VNote1)

Mode Symbol Condition TYP. MAX. Unit

Operating

mode

Note2,8

IDD1

All peripherals

running

Peripheral: fxx

PRSI option: 0

PLL: ON

12MHz≤fxx≤32MHz

fxx=20MHz

fx=5MHz 30 41 mA

fxx=32MHz

fx=16MHz 43 57 mA

PLL: OFF

4MHz≤fxx≤16MHz

fxx=8MHz

8MHz Internal-

OSC Note3

15 21 mA

fxx=16MHz

fx=16MHz 24 32 mA

Peripheral: fxx/2

PRSI option: 1

PLL: ON

12MHz≤fxx≤48MHz

fxx=48MHz

fx=12MHz 53 68 mA

All peripherals

stopped

Peripheral: fxx

PRSI option: 0

PLL: ON

12MHz≤fxx≤32MHz

fxx=20MHz

fx=5MHz 23 mA

fxx=32MHz

fx=16MHz 33 mA

PLL: OFF

4MHz≤fxx≤16MHz

fxx=8MHz

8MHz Internal-

OSC Note3

13 mA

fxx=16MHz

fx=16MHz 19 mA

Peripheral: fxx/2

PRSI option: 1

PLL: ON

12MHz≤fxx≤48MHz

fxx=48MHz

fx=12MHz 46 mA

HALT

mode

Note8

IDD2

All peripherals

running

Peripheral: fxx

PRSI option: 0

PLL: ON

12MHz≤fxx≤32MHz

fxx=20MHz

fx=5MHz 19 28 mA

fxx=32MHz

fx=16MHz 28 40 mA

PLL: OFF

4MHz≤fxx≤16MHz

fxx=8MHz

8MHz Internal-

OSC Note3

914mA

fxx=16MHz

fx=16MHz 15 22 mA

Peripheral: fxx/2

PRSI option: 1

PLL: ON

12MHz≤fxx≤48MHz

fxx=48MHz

fx=12MHz 31 42 mA

All peripherals

stopped

Peripheral: fxx

PRSI option: 0

PLL: ON

12MHz≤fxx≤32MHz

fxx=20MHz

fx=5MHz 13 mA

fxx=32MHz

fx=16MHz 18 mA

PLL: OFF

4MHz≤fxx≤16MHz

fxx=8MHz

8MHz Internal-

OSC Note3

6mA

fxx=16MHz

fx=16MHz 10 mA

Peripheral: fxx/2

PRSI option: 1

PLL: ON

12MHz≤fxx≤48MHz

fxx=48MHz

fx=12MHz 25 mA

Data Sheet U18567EE1V3DS00

V850ES/FJ3

IDLE1

mode IDD3

Peripheral (TAA, UARTD) run-

ning

PLL: OFF

4MHz≤fxx≤16MHz

Note7

fxx=5MHz

fx=5MHz 2.6 3.3 mA

fxx=12MHz

fx=12MHz 4.1 5.3 mA

fxx=16MHz

fx=16MHz 4.9 6.5 mA

fxx=8MHz, 8MHz Internal-OSCNote3 3.0 3.9 mA

All peripherals stopped

PLL: OFF

4MHz≤fxx≤16MHz

Note7

fxx=5MHz

fx=5MHz 1.4 mA

fxx=12MHz

fx=12MHz 1.8 mA

fxx=16MHz

fx=16MHz 2.0 mA

fxx=8MHz, 8MHz Internal-OSCNote3 1.3 mA

IDLE2

mode IDD4

PLL: OFF

4MHz≤fxx≤16MHz

Note7

fxx=5MHz

fx=5MHz 0.4 0.7 mA

fxx=12MHz

fx=12MHz 0.7 1.0 mA

fxx=16MHz

fx=16MHz 0.8 1.2 mA

fxx=8MHz, 8MHz Internal-OSC Note3 0.2 0.5 mA

SUB

operating

modeNote5

IDD5

Crystal resonator (fxt = 32,768kHz) 90 400 μA

RC resonator (fxt=20kHz) Note6 90 400 µA

240 kHz Internal-OSC (SubOSC stopped) 330 1310 µA

SubIDLE

mode

Note3,5

IDD6

Crystal resonator (fxt = 32,768kHz) 20 190 μA

RC resonator (fxt=20kHz) Note6 40 220 μA

240kHz Internal-OSC (SubOSC stopped) 25 180 μA

STOP

mode

Note3,4

IDD7

POC stop 240kHz Internal-OSC stop 7.5 100 μA

240kHz Internal-OSC working 15.5 115 μA

POC work 240kHz Internal-OSC stop 10.5 105 μA

240kHz Internal-OSC working 18.5 120 μA

Mode Symbol Condition TYP. MAX. Unit

28 Data Sheet U18567EE1V3DS00

V850ES/FJ3

(b) Calculation formulas

(Ta = -40 to +85°C, C=4.7uF,

VDD = EVDD = BVDD = 3.3 to 5.5V, AVREF0 = 3.3 to 5.5V, VSS = EVSS = BVSS = AVSS = 0VNote1))

Notes: 1. VDD, EVDD and BVDD total current. (Ports are stopped).

AVREF0 current, port buffer current (including a current flowing in the on-chip pull-up/pull-

down resistor) are not included.

2. The code flash and the data flash are in read mode.

When the device is in programming mode (Self-programming mode or data flash program-

ming mode), the current value (MAX. value) adds by the following value:

•Self-programming mode:

+ In case of PLL OFF: 7-(0.33*fxx+0.1) [mA]

+ In case of PLL ON: 7-(0.18*fxx+3.0) [mA]

•Data flash programming mode:

+ 7-(0.18*fxx/4+3.0) [mA]

3. Main OSC is stopped.

4. Do not use SubOSC.

5. POC is working. 240kHz Internal-OSC is working. 8MHz Internal-OSC is stopped.

6. RC Oscillation frequency is typ.40kHz. This clock is divided by 2 internally.

7. 8MHz Internal-OSC is stopped

8. When the SSCG is running, the current value adds typ +2.5mA, max +4mA.

9. The formulas are for reference only. Not all possible values for fxx are tested in the outgoing

device inspection.

Mode Symbol Condition TYP. Note9 MAX. Note9 Unit

Operating

mode

Note2,8

IDD1

All peripherals

running

Peripheral: fxx

PRSI option: 0

PLL: ON

12MHz≤fxx≤32MHz 1.12⋅fxx+7.1 1.35⋅fxx+13.6 mA

PLL: OFF

4MHz≤fxx≤16MHz 1.13⋅fxx+5.5 1.35⋅fxx+10.6 mA

Peripheral: fxx/2

PRSI option: 1

PLL: ON

12MHz≤fxx≤32MHz 0.97⋅fxx+6.0 1.17⋅fxx+12.2 mA

All peripherals

stopped

Peripheral: ffxx-

PRSI option: 0

PLL: ON

12MHz≤fxx≤32MHz 0.85⋅fxx+6.2 mA

PLL: OFF

4MHz≤fxx≤16MHz 0.86⋅fxx+5.7 mA

Peripheral: fxx/2

PRSI option: 1

PLL: ON

12MHz≤fxx≤32MHz 0.82⋅fxx+6.2 mA

HALT

mode

Note8

IDD2

All peripherals

running

Peripheral: ffxx-

PRSI option: 0

PLL: ON

16MHz≤fxx≤32MHz 0.75⋅fxx+3.0 1.04*fxx+6.9 mA

PLL: OFF

4MHz≤fxx≤16MHz 0.72⋅fxx+3.0 1.00*fxx+5.5 mA

Peripheral: fxx/2

PRSI option: 1

PLL: ON

16MHz≤fxx≤32MHz 0.56⋅fxx+4.0 0.69*fxx+8.5 mA

All peripherals

stopped

Peripheral: fxx

PRSI option: 0

PLL: ON

16MHz≤fxx≤32MHz 0.46⋅fxx+3.6 mA

PLL: OFF

4MHz≤fxx≤16MHz 0.46⋅fxx+2.6 mA

Peripheral: fxx/2

PRSI option: 1

PLL: ON

16MHz≤fxx≤32MHz 0.46⋅fxx+2.8 mA

IDLE1

mode IDD3

Peripheral (TAA, UARTD) run-

ning

PLL: OFF

4MHz≤fxx≤16MHz

Note7

0.211⋅fxx+1.54 0.295⋅fxx+ 1.80 mA

All peripherals stopped 0.054⋅fxx+1.15 mA

IDLE2

mode IDD4 PLL: OFF

4MHz ≤fxx≤16MHz Note7 0.037⋅fxx+0.21 0.049⋅fxx+ 0.43 mA

Data Sheet U18567EE1V3DS00

V850ES/FJ3

2.7 AC Characteristics

AC test Input measurement points ( VDD, AVREF0, EVDD, BVDD)

AC test output measurement points

Load conditions

Caution: If the load capacitance exceeds 50pF due to the circuit configuration, reduce the load

capacitance of the device to 50pF or less by inserting a buffer or by some other means.

2.7.1 CLKOUT Output Timing

(Ta = -40 to +85°C, VDD = EVDD = BVDD = 3.5 to 5.5V, AVREF0 = 3.5 to 5.5V, VSS = EVSS = BVSS = AVSS = 0V, CL=50pF)

CLKOUT output timing

Parameter Symbol Conditions MIN. MAX. Unit

Output cycle tCYK VDD = EVDD = BVDD = 4.0V ~ 5.5V 31.25ns 80μs

VDD = EVDD = BVDD = 3.5V ~ 5.5V 50ns

High level width tWKH VDD = EVDD = BVDD = 4.0V ~ 5.5V tCYK/2-13 ns

VDD = EVDD = BVDD = 3.5V ~ 5.5V tCYK/2-15

Low level width tWKL VDD = EVDD = BVDD = 4.0V ~ 5.5V tCYK/2-13 ns

VDD = EVDD = BVDD = 3.5V ~ 5.5V tCYK/2-15

Rise time tKR VDD = EVDD = BVDD = 4.0V ~ 5.5V 13 ns

VDD = EVDD = BVDD = 3.5V ~ 5.5V 15

Fall time tKF VDD = EVDD = BVDD = 4.0V ~ 5.5V 13 ns

VDD = EVDD = BVDD = 3.5V ~ 5.5V 15

measure point

VIH(min)

VIL(max)

VIH(min)

VIL(max)

VDD

VSS

measure point

VOH(min)

VOL(max)

VOH(min)

VOL(max)

CL = 50 pF

DUT

( Device under

test )

KR t

WKH t

WKL

CYK

CLKOUT

30 Data Sheet U18567EE1V3DS00

V850ES/FJ3

2.7.2 Bus Timing (Multiplexed bus mode)

(a) CLKOUT asynchronous: In multiplexed bus mode

(Ta = -40 to +85°C, VDD = EVDD = BVDD = 3.5 to 5.5V, AVREF0 = 3.5 to 5.5V, VSS = EVSS = BVSS = AVSS = 0V, CL=50pF)

Parameter Symbol Conditions MIN. MAX.

Unit

Address setup time ( to ASTB

↓

) tSAST <14> (0.5+tASW)T-20

Address hold time ( from ASTB

↓

) tHSTA <15> (0.5+tAHW)T-15

Delay time from _RD

↓

to address float tFRDA <16> 16

Data Input setup time from address tSAID <17> (2+n+tASW+tAHW)T-

Data Input setup time from _RD

↓

tSRDID <18> (1+n)T-34

Delay time from ASTB

↓

to _RD

↓

, _WRm

↓

tDSTRDWR <19> (0.5+tAHW)T-15

Data Input hold time (from _RD

↑

) tHRDID <20> 0

Address output time from _RD

↑

tDRDA <21> (1+i+tAHW)T-15

Delay time from _RD

↑

, _WRm

↑

to ASTB

↑

tDRDWRST <22> 0.5T-15

Delay time from _RD

↑

to ASTB

↓

tDRDST <23> (1.5+i+tAHW)T-15

_RD, _WRn low level width tWRDWRL <24> (1+n)T-20

ASTB high level width tWSTH <25> (1+i+tASW)T-15

Data output time from _WRm

↓

tDWROD <26> 15

Data output setup time (to _WRm

↑

) tSODWR <27> (1+n)T-25

Data output hold time (from _WRm

↑

) tHWROD <28> T-15

_WAIT setup time ( to address )

tSAWT1 <29>

n≥1

(1.5+tASW+tAHW)T-45

tSAWT2 <30> (1.5+n+tASW+tAHW)T-

_WAIT hold time ( from address ) tHAWT1 <31>

n≥1

(0.5+n+tASW+tAHW)T

tHAWT2 <32> (1.5+n+tASW+tAHW)T

_WAIT setup time (to ASTB

↓

)tSSTWT1 <33>

n≥1

(1+tAHW)T-35

tSSTWT2 <34> (1+n+tAHW)T-35

_WAIT hold time ( from ASTB

↓

)tHSTWT1 <35>

n≥1

(n+tAHW)T

tHSTWT2 <36> (1+n+tAHW)T

_HLDRQ high level width tWHQH <37> T+10

_HLDAK low level width tWHAL <38> T-20

Delay time from _HLDAK

↑

to bus output tDHAC <40> -3

Delay time from _HLDRQ

↓

to _HLDAK

↓

tDHQHA1 <41> (2n+7.5)T+25

Delay time from _HLDRQ

↑

to _HLDAK

↑

tDHQHA2 <42> 0.5T 1.5T+35

Data Sheet U18567EE1V3DS00

V850ES/FJ3

(b) CLKOUT synchronous: In multiplexed bus mode

(Ta = -40 to +85°C, VDD = EVDD = BVDD = 3.5 to 5.5V, AVREF0 = 3.5 to 5.5V, VSS = EVSS = BVSS = AVSS = 0V, CL=50pF)

Remarks: 1. T=1/fcpu (fcpu: CPU operation clock frequency)

2. n: Number of wait clocks Inserted In the bus cycle.

The sampling timing changes when a programmable wait is Inserted.

3. i: Number of Idle states Inserted after the read cycle ( 0 or 1 ).

4. The values In the above specifications are values for when clocks with a 1: 1 duty ratio

are Input from X1

5. m=0,1

6. tASW=Number of address setup wait clocks (0 or 1)

tAHW=Number of address hold wait clocks (0 or 1)

7. When the operation frequency is high, it is not possible to access by no wait bus cycle.

Please insert wait clock (data wait (n)) / address setup wait (tASW) / address hold wait

(tAHW)).

Example: Set the following in accordance to the CPU operating clock frequency

(k=0 to 3).

•In case of Flash ≤ 256KB product

•31.25ns≤1/fcpu<40ns: Set an address setup wait (AWC.ASWk bit=1).

•In case of Flash ≥ 384KB product

•30ns≤1/fcpu<40ns: Set an address setup wait (AWC.ASWk bit=1).

•20.8ns≤1/fcpu<30ns: Set an address setup wait (AWC.ASWk bit=1) and address

hold wait (AWC.AHWk bit=1).

•20.8ns≤1/fcpu≤25ns: Set a data wait (minimum 1 wait)

Parameter Symbol Conditions MIN. MAX. Unit

Delay time from CLKOUT↑ to address tDKA <43> 0 24 ns

Delay time from CLKOUT↑ to address float tFKA <44> 0 24 ns

Delay time from CLKOUT↓ to ASTB tDKST <45> -7 18 ns

Delay time fromCLKOUT↑ to _RD, _WRm tDKRDWR <46> -2 18 ns

Data Input setup time (from CLKOUT↑) tSIDK <47> 20 ns

Data Input hold time (from CLKOUT↑) tHKID <48> 5 ns

Data output delay time (from CLKOUT↑) tDKOD <49> 27 ns

_WAIT setup time (to CLKOUT↓) tSWTK <50> 30 ns

_WAIT hold time (from CLKOUT↓) tHKWT <51> 5 ns

HLDRQ setup time ( to CLKOUT↓) tSHQK <52> 30 ns

_HLDRQ hold time (from CLKOUT↓) tHKHQ <53> 5 ns

Delay time from CLKOUT↑ to _HLDAK tDKHA <54> 24 ns

Delay time from CLKOUT↑ to address float tDKF <55> 25 ns

32 Data Sheet U18567EE1V3DS00

V850ES/FJ3

Read Cycle ( CLKOUT Synchronous/ Asynchronous, 1 Wait ): In Multiplexed Bus Mode

Remark: _WR0 and _WR1 are high level.

<17>

<43>

<47>

<48>

<45>

<20>

<22>

<46>

<23>

Data

<44>

Address

< 45>

< 15>

< 14>

< 25>

<46>

<16>

<18>

< 19>

Hi-Z

<21>

<24>

<51>

<50>

<51>

<50>

< 33>

<35>

<34>

<36>

< 29>

< 31>

< 30>

< 32>

T2 TW T3

CLKOUT (output)

_CS0 to _CS3 (output)

AD0 to AD15 (I/O)

ASTB (output)

RD (output)

WAIT (input)

Data Sheet U18567EE1V3DS00

V850ES/FJ3

Write Cycle ( CLKOUT Synchronous/ Asynchronous, 1 Wait ): In Multiplexed Bus Mode

Remark: _RD Is high level.

< 43>

<45>

<22>

Data

<49>

Address

< 45>

< 15>

< 14>

< 25>

<46>

<27>

<28>

<24>

<51>

<50>

<51>

<50>

< 33>

<35>

<34>

<36>

< 29>

< 31>

< 30>

< 32>

T2 TW T3

CLKOUT (output)

AD0 to AD15 (I/O)

ASTB (output)

WR0 (output),

WR1 (output)

WAIT (input)

<46>

<26>

< 19>

_CS0 to _CS3 (output)

34 Data Sheet U18567EE1V3DS00

V850ES/FJ3

Bus Hold: In Multiplexed Bus Mode

CLKOUT(output)

_HLDRQ(input)

TH TH TH TI

_HLDAK(output)

AD0 to A D15 (I/O)

ASTB(output)

_RD(output)

_WR0,_WR1(output)

<52>

<53>

<52>

<37>

<41>

<54>

<42>

<55>

<38>

<40>

Hi-Z

_CS0 to _CS3(output)

Hi-Z

Data Sheet U18567EE1V3DS00

V850ES/FJ3

2.7.3 RESET, Interrupt, ADTRG Timing

(Ta = -40 to +85°C, VDD = EVDD = BVDD = 3.3 to 5.5V, AVREF0 = 3.3 to 5.5V, VSS = EVSS = BVSS = AVSS = 0V, CL=50pF)

Notes: 1. ADTRG is same spec (P03/INTP0/ADTRG). DRST is same spec (P05/INTP2/DRST)

2. 2Tsamp+20 or 3Tsamp+20 ("Tsamp" is Noise reject sampling clock (NF macro))

Remarks: 1. The above minimum values show pulse widths that are surely detected as an effective

edge. An effective may also be detected even if the input pulse width is less than the

above minimum specification.

2. RESET, NMI, INTPn, ADTRG and DRST have analog noise filter. The typical filter time

is typ=60ns.

2.7.4 Key Return Timing

(Ta = -40 to +85°C, VDD = EVDD = BVDD = 3.3 to 5.5V, AVREF0 = 3.3 to 5.5V, VSS = EVSS = BVSS = AVSS = 0V, CL=50pF)

Remarks: 1. The above minimum values show pulse widths that are surely detected as an effective

edge. An effective may also be detected even if the input pulse width is less than the

above minimum specification.

2. KRn inputs have analog noise filter. The typical filter time is typ=60ns.

2.7.5 Timer Timing

(Ta = -40 to +85°C, VDD = EVDD = BVDD = 3.5 to 5.5V, AVREF0 = 3.5 to 5.5V, VSS = EVSS = BVSS = AVSS = 0V, CL=50pF)

Notes: 1. Except for the external trigger and external event function.

Remarks: 1. The above minimum values show pulse widths that are surely detected as an effective

edge. An effective may also be detected even if the input pulse width is less than the

above minimum specification.

2. TIAAn and TIABn inputs have analog noise filter. The typical filter time is typ=60ns.

Parameter Symbol Conditions MIN. TYP. MAX. Unit

_RESET input low level width tWRSL analog filter 250 ns

NMI input high level width tWNIH analog filter 250 ns

NMI input low level width tWNIL analog filter 250 ns

INTPnNote1 input high level width tWITH analog filter ,n=0-14 250 ns

digital filter ,n=3 Note2 ns

INTPn Note1 input low level width tWITL analog filter ,n=0-14 250 ns

digital filter ,n=3 Note2 ns

Parameter Symbol Conditions MIN. TYP. MAX. Unit

KRn input high level width tWKRH analog filter ,n=0-7 250 ns

KRn input low level width tWKRL analog filter ,n=0-7 250 ns

Parameter Symbol Conditions MIN. TYP. MAX. Unit

TI input high level

width tTIH TIAA00-01,10-11,20-21,30-31,40-41 Note1

TIAB00-03,10-13,20-23 Note1 250 ns

TI input low level

width tTIL TIAA00-01,10-11,20-21,30-31,40-41 Note1

TIAB00-03,10-13,20-23 Note1 250 ns

TO output cycle tTCYK

TIAA00-01,10-11,20-21,30-31,

40-41 Note1

TIAB00-03,10-13,20-23 Note1

4.0V≤VDD≤5.5V 16 MHz

3.5V≤VDD<4.0V 10 MHz

36 Data Sheet U18567EE1V3DS00

V850ES/FJ3

2.7.6 CSI Timing

(a) Master mode

(Ta = -40 to +85°C, VDD = EVDD = BVDD = 3.5 to 5.5V, AVREF0 = 3.5 to 5.5V, VSS = EVSS = BVSS = AVSS = 0V, CL=50pF)

(b) Slave mode

(Ta = -40 to +85°C, VDD = EVDD = BVDD = 3.5 to 5.5V, AVREF0 = 3.5 to 5.5V, VSS = EVSS = BVSS = AVSS = 0V, CL=50pF)

2.7.7 UART Timing

(Ta = -40 to +85°C, VDD = EVDD = BVDD = 3.5 to 5.5V, AVREF0 = 3.5 to 5.5V, VSS = EVSS = BVSS = AVSS = 0V, CL=50pF)

Parameter Symbol Conditions MIN. MAX. Unit

SCKBn cycle time tKCY1 125 ns

SCKBn high level width tKH1 tKCY1/2-15 ns

SCKBn low level width tKL1 tKCY1/2-15 ns

SIBn setup time ( to SCKBn ) tSIK1 30 ns

SIBn hold time ( from SCKBn ) tKSI1 25 ns

Delay time from SCKBn to SOBn tKSO1 25 ns

Parameter Symbol Conditions MIN. MAX. Unit

SCKBn cycle time tKCY1 200 ns

SCKBn high level width tKH1 90 ns

SCKBn low level width tKL1 90 ns

SIBn setup time ( to SCKBn ) tSIK1 50 ns

SIBn hold time ( from SCKBn ) tKSI1 50 ns

Delay time from SCKBn to SOBn tKSO1 50 ns

Parameter Symbol Conditions MIN. TYP. MAX. Unit

Transfer rate 1.5 Mbps

ASCK0 frequency 10 MHz

tSIKn tKSIn

tKCYn

CSIBn n=0

–

tKLn tKHn

tKSOn

Output data

Input data

SOBn

SIBn

SCKBn

Data Sheet U18567EE1V3DS00

V850ES/FJ3

2.7.8 IIC Timing

(Ta = -40 to +85°C, VDD = EVDD = BVDD = 3.5 to 5.5V, AVREF0 = 3.5 to 5.5V, VSS = EVSS = BVSS = AVSS = 0V, CL=50pF)

Notes: 1. At the start condition, the first clock pulse is generated after the hold time

2. The system requires a minimum of 300ns hold time Internally for the SDA signal ( at VIH-

min. of SCL00 signal )

In order to occupy the undefined area at the falling edge of SCL00.

3. If the system does not extend the SCL00 signal low hold time ( tlow ), only the maximum

data hold time (tHD:DAT ) needs to be satisfied.

4. The high-speed-mode IIC bus can be used In a normal-mode IIC bus system.

In this case, set the high-speed-mode IIC bus so that It meets the following conditions.

- If the system does not extend the SCL00 signal's low state hold time:

SU:DAT?250ns

- If the system extends the SCL00 signal's low state hold time:

Transmit the following data bit to the SDA00 line prior to releasing the SCL00 line

(tRmax.+tSU:DAT=1000+250=1250ns: Normal mode IIC bus specification ).

5. Cb: Total capacitance of one bus line (unit: pF)

Parameter Symbol Normal mode High-speed mode Unit

min. max. min. max.

SCL00 clock frequency fCLK 0 100 0 400 kHz

Bus-free time (between stop/start condi-

tions) tBUF 4.7 1.3 us

Hold timeNote1 tHD:STA 4.0 0.6 us

SCL00 clock low-level width tLOW 4.7 1.3 us

SCL00 clock high-level width tHIGH 4.0 0.6 us

Setup time for start/restart conditions tSU:STA 4.7 0.6 us

Data hold

time

CBUS compatible master tHD:DAT 5.0 us

IIC mode 0Note2 0Note2 0.9Note3 us

Data setup time tSU:DAT 250 100Note4 ns

SDA00 and SCL00 signal rise time tR 1000 20+0.1Cb 300 ns

SDA00 and SCL00 signal fall time tF 300 20+0.1Cb 300 ns

Stop condition setup time tSU:STO 4.0 0.6 us

Pilse width with spike supporessed by

input filter tSP 0 50 ns

Capacitance load of each bus line Cb 400 400 pF

38 Data Sheet U18567EE1V3DS00

V850ES/FJ3

IIC bus interface timing

Remark: P: Stop condition

S: Start condition

Sr: Restart condition

P Sr

tSU:STO tSP tHD:STA

S P

tBUF

tHD:DAT tHD:STA

tR tLOW

SCL00

tSU:STA

tHIGH

SDA00

tSU:DAT

Data Sheet U18567EE1V3DS00

V850ES/FJ3

2.7.9 CAN Timing

(Ta = -40 to +85°C, VDD = EVDD = BVDD = 3.5 to 5.5V, AVREF0 = 3.5 to 5.5V, VSS = EVSS = BVSS = AVSS = 0V, CL=50pF)

Parameter Symbol Conditions MIN. TYP. MAX. Unit

Transfer rate 1Mbps

Internal delay time 100 ns

CRXDn pin

( Receive data )

Internal delay time (tNODE)= Internal Transfer Delay(toutput) + Internal Receive Delay(tinput)

tinput

toutput

CTXDn pin

( Transfer data )

CAN Internal clock*

*) CAN Internal clock (fCAN) :CAN baud rate clock

CTXDn pin

CRXDn pin

Image figure of Internal delay

CAN

macro

Internal Transfer delay

Internal Receive delay

V850ES/Fx3

40 Data Sheet U18567EE1V3DS00

V850ES/FJ3

2.8 A/D Converter

(Ta = -40 to +85°C, C=4.7uF, VDD = EVDD = BVDD = 3.5 to 5.5V, AVREF0 = 4.0 to 5.5V, VSS = EVSS = BVSS = AVSS = 0V)

Notes: 1. Overall error excluding quantization error (±0.05%FSE). It is indicated as a ratio to the full-

scale value.

2. Excluding quantization error (±1/2 LSB)

3. Not tested in production.

4. Does not include input/output capacitance CIO

Parameter Symbol Conditions MIN. TYP. MAX. Unit

Resolution 10 bit

Overall errorNote1 4.0V≤AVREF0<5.5V ±0.15 ±0.3 %FSR

Conversion time tCONV 3.10 16 μs

Stabilization time tSTA After ADA0PS bit = 0 -> 1 2 μs

Recovery time for power down

mode tDPU 1 µs

Zero-scale errorNote1 ZSE ±0.3 %FSR

Full-scale errorNote1 FSE ±0.3 %FSR

Integral non-liniearity errorNote2 INL ±2.5 LSB

Differential non-liniearity errorNote2 DNL ±1.5 LSB

Analog input voltage VIAN AVSS AVREF0 V

Analog input equivalent

circuit capacitance Note3,4 CINA 6.19 pF

Analog input equivalent

circuit resistance Note3 RINA 2.55 kΩ

AVREF0 current IAREF0 A/D operating 4 7 mA

A/D operation stop 1 10 uA

Conversion rusult when using

Diagnostic function

AVREF0 conversion 3FC 3FF HEX

AVSS conversion 000 003 HEX

Data Sheet U18567EE1V3DS00

V850ES/FJ3

2.9 POC

(Ta = -40 to +85°C, C=4.7uF, VDD = EVDD = BVDD, VSS = EVSS = BVSS = AVSS = 0V)

Notes: 1. From detect voltage to release reset signal

2. From detect voltage to occurrence of reset signal

Note: POC is available only in M2 devices. Refer to ’Ordering information’ in the V850ES/Fx3 User’s

Manual.

Parameter Symbol Conditions MIN. TYP. MAX. Unit

Detect voltage VPOC0 3.3 3.5 3.7 V

Supply voltage rise time tPTH From VDD=0V to

VDD=3.3V 0.002 ms

Response time1 Note1 tPTHD In case of power on.

After VDD reaches 3.7V. 2.0 ms

Response time2 Note2 tPD In case of power off.

After VDD drop 3.3V. 0.2 1.0 ms

VDD minimum width tPW 0.2 ms

tPTH tPTHD tPD

tPW

VDD

(TYP.)

(MIN.)

Detect voltag(MAX.)

tPTHD

42 Data Sheet U18567EE1V3DS00

V850ES/FJ3

2.10 LVI

(Ta = -40 to +85°C, C=4.7uF, VDD = EVDD = BVDD = 3.3 to 5.5V, AVREF0 = 3.3 to 5.5V, VSS = EVSS = BVSS = AVSS = 0V)

Notes: 1. From detect voltage to occurrence interrupt/reset signal

2. If POC functionality is available, the wait time is not needed.

2.11 RAM Retention Flag

(Ta = -40 to +85°C, C=4.7uF, VDD = EVDD = BVDD = 1.9 to 5.5V, VSS = EVSS = BVSS = AVSS = 0V)

Notes: 1. From detect voltage to set RAMFbit (RAMS.bit0)

Parameter Symbol Conditions MIN. TYP. MAX. Unit

Detect voltage VLVI0 3.8 4.0 4.2 V

VLVI1 3.5 3.7 3.9 V

Response time Note1 tLD After VDD reaches VLVI0/1(max).

After VDD drop VLVI0/1(min). 0.2 2.0 ms

VDD minimum width tLW 0.2 ms

Reference voltage stabilization

wait time Note2 tLWAIT After VDD reaches 3.3V.

After LVION bit (LVIM.bit7) = 0->1 0.1 0.2 ms

Parameter Symbol Conditions MIN. TYP. MAX. Unit

Detect voltage VRAMH 1.9 2.0 2.1 V

Supply voltage rise time tRAMHTH From VDD=0V to VDD=3.3V 0.002 1800 ms

Response time Note1 tRAMHD After VDD reaches 2.1V. 0.2 2.0 ms

VDD minimum width tRAMHW 0.2 ms

tLWAIT tLD

tLW

VDD

(TYP.)

(MIN.)

Detect voltag(MAX.)

Operation voltage (MIN.)

LVION bit=0 1(LVI function work)

tLD

tRAMHTH

tRAMHD tRAMHW

VDD

(TYP.)

(MIN.)

Detect voltag(MAX.)

Operation voltage (MIN.)

tRAMHD

Data Sheet U18567EE1V3DS00

V850ES/FJ3

2.12 Data Retention Characteristics

(Ta = -40 to +85°C, C=4.7uF, VDD = EVDD = BVDD = 1.9 to 5.5V, VSS = EVSS = BVSS = AVSS = 0V) (

Remark: When STOP mode is entered/released operation voltage range must be controlled.

Parameter Symbol Conditions MIN. TYP. MAX. Unit

Data retention power

supply voltage VDDDR STOP mode

(All function is stopped) 1.9 5.5 V

Data retention power

supply current IDDDR VDDDR=2.0V(

All function is stopped) 6.5 70 μA

Supply voltage rise time tRVD 1 μs

Supply voltage fall time tFVD 1 μs

Supply voltage hold time tHVD After STOP mode 0 ms

STOP release signal input

time tDREL

After VDD reaches operat-

ing voltage range MIN.

3.3V

0ms

Data retention high-level

input voltage VIHDR All input port 0.9VDDDR VDDDR V

Data retention low-level

input voltage VILDR All input port 0 0.1VDDDR V

Operation voltage(min.)

Setting STOP mode

tHVD VDDDR

VIHDR

tDREL

VILDR

NMI,INTPn(Input)

(When STOP mode is

released at rising edge)

NMI,INTPn(Input)

(When STOP mode is

released at falling edge)

_RESET

VDD/EVDD/BVDD

tFVD tRVD

44 Data Sheet U18567EE1V3DS00

V850ES/FJ3

2.13 Flash Memory Programming Characteristics

(a) Basic Characteristics

(C=4.7uF, VDD = EVDD = BVDD, AVREF0 = 3.5 to 5.5V, VSS = EVSS = BVSS = AVSS = 0V)

Notes: 1. Under the condition of CWRT1

2. Under the condition of CWRT2

Remark: The initial write when the product is shipped, any erase → write set of operations, or any

programming operation is counted as one rewrite.

Example: P: Program(write) E: Erase

Product is shipped → P → E → P → E → P : Rewrite count: 3

Product is shipped → E → P → E → P → E → P : Rewrite count: 3

(b) Serial Writing Operation Characteristics

(Ta = -40 to +85°C, C=4.7uF, VDD = EVDD = BVDD, AVREF0 = 3.5 to 5.5V, VSS = EVSS = BVSS = AVSS = 0V, CL=50pF)

Parameter Symbol Conditions MIN. TYP. MAX. Unit

Operation frequency fCPU ≤256KB product 4 32 MHz

≥384KB product 4 48

Supply voltage VDD 3.3 5.5 V

Number of rewrites CWRT1 Code Flash 1000 count

Data Flash

CWRT2 10000

High level input voltage VIH FLMD0 0.8EVDD EVDD V

Low level input voltage VIL FLMD0 EVSS 0.2EVDD V

Programming temperature tPRG -40 +85 °C

Data retention

Code Flash 15Note1

year

Data Flash 5Note2

Parameter Symbol Conditions MIN. TYP. MAX. Unit

FLMD0 setup time (from VDD) tDP 1 ms

RESET release (from FLMD0) tPR 2 ms

FLMD0 pulse input start

(from raise edge of _RESET) tRP 800 μs

FLMD0 high level width /

low level width tPW 10 100 μs

FLMD0 raise time tR 50 ns

FLMD0 fall time tF 50 ns

Data Sheet U18567EE1V3DS00

V850ES/FJ3

3. Electrical Specifications of (A1)-Grade

This product has to be used only under the conditions of VDD=EVDD=BVDD. Operation is not ensured

at the time of using this product except this condition.

3.1 Absolute Maximum Ratings

AbsAbsolute Maximum Ratings (Ta=25°C)

Remarks: 1. The characteristics of the dual-function pins are the same as those of the port pins

unless otherwise specified

Notes: 1. Be sure not to exceed the absolute maximum ratings (Max. value) of each supply voltage.

2. Excluding ADC IAREF0 current.

3.2 Capacities

Specification is identical to that from (A)-Grade except Ta=-40 to +110°C.

3.3 Operating condition

Specification is identical to that from (A)-Grade except Ta=-40 to +110°C.

3.4 Voltage Regulator Characteristics

Specification is identical to that from (A)-Grade except Ta=-40 to +110°C.

Parameter Symbol Conditions Rating Unit

Supply voltage

VDD VDD=EVDD=BVDD, -0.5 to +6.5 V

EVDD VDD=EVDD=BVDD -0.5 to +6.5 V

BVDD VDD=EVDD=BVDD -0.5 to +6.5 V

AVREF0 -0.5 to +6.5 V

VSS VSS=EVSS=BVSS=AVSS -0.5 to +0.5 V

EVSS VSS=EVSS=BVSS=AVSS -0.5 to +0.5 V

BVSS VSS=EVSS=BVSS=AVSS -0.5 to +0.5 V

AVSS VSS=EVSS=BVSS=AVSS -0.5 to +0.5 V

Input voltage

VI1 Pin Group 1x, 6 -0.5 to EVDD+0.5

Note1 V

VI2 Pin Group 3x -0.5 to BVDD+0.5

Note1 V

VI3 Pin Group 7 -0.5 to VRO+0.5

Note1 V

Analog input voltage VIAN Pin Group 4 -0.5 to AVREF0+0.5

Note1 V

High level output cur-

rent IOH

Pin Group 1x 1 pin -4 mA

Total - 2 0 mA

Pin Group 3x 1 pin -4 mA

Total - 2 0 mA

Pin Group 4 1 pin -4 mA

Total - 1 0Note2 mA

Low level output current IOL

Pin Group 1x 1 pin 4 mA

Total 2 0 m A

Pin Group 3x 1 pin 4 mA

Total 2 0 m A

Pin Group 4 1 pin 4 mA

Total 1 0 Note2 mA

Operating ambient

temperature Ta Normal operating mode -40 to +110 °C

Flash programming mode -40 to +110

Storage temperature Tstg -40 to +125 °C

46 Data Sheet U18567EE1V3DS00

V850ES/FJ3

3.5 Clock Generator Circuit

3.5.1 Main System Clock Oscillation Circuit Characteristics

Specification is identical to that from (A)-Grade except Ta=-40 to +110°C.

3.5.2 Sub System Clock Oscillation Circuit Characteristics

(Ta = -40 to +110°C, C=4.7uF, VDD = EVDD = BVDD = 3.3 to 5.5V, AVREF0 = 3.3 to 5.5V, VSS = EVSS = BVSS = AVSS = 0V)

Notes: 1. Indicates only oscillation circuit characteristics. Refer to "AC Characteristic" for cpu opera-

tion clock.

2. Time required to stabilize oscillation after VDD reaches oscillator voltage range min. 3.3V

3. In order to avoid the influence of wiring capacity, shorten wiring as much as possible.

4. RC Oscillation frequency is typ. 40kHz. This clock is divided by 2 internally. In case of RC

Oscillator, internal system clock frequency(fxt) is min. 12.5kHz, typ. 20kHz, max. 27.5kHz.

3.5.3 Internal-OSC Characteristics

Specification is identical to that from (A)-Grade except Ta=-40 to +110°C.

3.5.4 PLL Characteristics

Specification is identical to that from (A)-Grade except Ta=-40 to +110°C.

3.5.5 SSCG Characteristics

Specification is identical to that from (A)-Grade except Ta=-40 to +110°C.

Resonator Recommended Circuit Parameter Conditions MIN. TYP. MAX. Unit

resonator Refer to Figure 2

Oscillator

frequencyNote1,4

R=390KΩ ±5% Note3,

C=47pF±10% Note3 25 40 55 kHz

Oscillation stabiliza-

tion time Note2 100 μs

XT1 XT2

Data Sheet U18567EE1V3DS00

V850ES/FJ3

3.6 DC Characteristics

3.6.1 Input/Output Level

(Ta = -40 to +110°C, C=4.7uF, VDD = EVDD = BVDD = 3.3 to 5.5V, AVREF0 = 3.3 to 5.5V, VSS = EVSS = BVSS = AVSS = 0V)

Remark: The characteristics of the dual-function pins are the same as those of the port pins unless

otherwise specified.

Notes: 1. DRST terminal only. (Control register is OCDM)

2. Total IOH/IOL max is 20mA/-20mA for the power supply lines EVDD and BVDD.

Total IOH/IOL max is 10mA/-10mA for the power supply line AVREF0.

AVREF0 IOH/IOL current is excluding ADC current IAREF0.

3. Typical value. Not tested and guaranteed

Parameter Sym-

bol Conditions MIN. TYP. MAX. Uni

High level

input voltage

VIH1 Pin Group 1B 0.7⋅EVDD EVDD V

VIH2 Pin Group 1D 0.8⋅EVDD EVDD V

Pin Group 3D 0.8⋅BVDD BVDD V

VIH3 Pin Group 3A 0.7⋅BVDD BVDD V

VIH4 Pin Group 4 0.7⋅AVREF0 AVREF0 V

VIH5 Pin Group 6 0.8⋅EVDD EVDD V

Low level

input voltage

VIL1 Pin Group 1B EVSS 0.3⋅EVDD V

VIL2 Pin Group 1D EVSS 0.4⋅EVDD V

Pin Group 3D BVSS 0.4⋅BVDD V

VIL3 Pin Group 3A BVSS 0.3⋅BVDD V

VIL4 Pin Group 4 AVSS 0.3⋅AVREF0 V

VIL5 Pin Group 6 EVSS 0.2⋅EVDD V

Input hysteresis

VHYS1 Pin Group 1B Center point at

0.5 x EVDD Note3 0.267 x EVDD - 0.51V V

VHYS2

Pin Group 1D Center point at

0.6 x EVDD Note3 0.192 x EVDD - 0.31V V

Pin Group 3D Center point at

0.6 x BVDD Note3 0.192 x BVDD - 0.31V V

VHYS5 Pin Group 6 Center point at

0.5 x EVDD Note3 0.535 x EVDD - 0.9V V

High level

output voltage

Note2

VOH1 Pin Group 1x IOH=-1.0mA EVDD-1.0 EVDD V

IOH=-100uA EVDD-0.5 EVDD V

VOH2 Pin Group 3x IOH=-1.0mA BVDD-1.0 BVDD

IOH=-100uA BVDD-0.5 BVDD V

VOH3 Pin Group 4 IOH=-1.0mA AVREF0-1.0 AVREF0 V

IOH=-100uA AVREF0-0.5 AVREF0 V

Low level output

voltageNote2

VOL1 Pin Group 1x IOL=1.0mA 00.4V

P914, 915 IOL=3.0mA

VOL2 Pin Group 3x IOL=1.0mA 0 0.4 V

VOL3 Pin Group 4 IOL=1.0mA 0 0.4 V

Software pull-up

resistor R1 VI=0V 10 30 100 kΩ

Software Note1

pull-down resistor R2 VI=VDD 10 30 100 kΩ

48 Data Sheet U18567EE1V3DS00

V850ES/FJ3

3.6.2 PIN leakage current

(Ta = -40 to +110°C, C=4.7uF, VDD = EVDD = BVDD = 3.3 to 5.5V, AVREF0 = 3.3 to 5.5V, VSS = EVSS = BVSS = AVSS = 0V)

Notes: 1. The input leakage current of FLMD0 is as follows:

High level input leakage current : 4.0uA

Low level input leakage current : -4.0uA

3.6.3 Power supply current (A1-grade)

3.6.3.1 µPD70F3378

(a) Absolute values

(Ta = -40 to +110°C, C=4.7uF,

VDD = EVDD = BVDD = 3.3 to 5.5V, AVREF0 = 3.3 to 5.5V, VSS = EVSS = BVSS = AVSS = 0VNote1)

Parameter Symbol Conditions MIN. TYP. MAX. Unit

High level input

leakage current ILIH1 VI=VDD Analog pins 0.4

Other pins Note1 0.8

Low level input

leakage current ILIL1 VI=0V Analog pins -0.4

Other pins Note1 -0.8

High level output

leakage current ILOH1 VO=VDD Analog pins 0.4

Other pins 0.8

Low level output

leakage current ILOL1 VO=0V Analog pins -0.4

Other pins -0.8

Mode Symbol Condition TYP. MAX. Unit

Operating

mode

Note2,8

IDD1

All peripherals

running

Peripheral: fxx

PRSI option: 0

PLL: ON

12MHz≤fxx≤32MHz

fxx=20MHz

fx=5MHz 28 38 mA

fxx=32MHz

fx=16MHz 40 53 mA

PLL: OFF

4MHz≤fxx≤16MHz

fxx=8MHz

8MHz Internal-

OSC Note3

14 21 mA

fxx=16MHz

fx=16MHz 22 30 mA

Peripheral: fxx/2

PRSI option: 1

PLL: ON

12MHz≤fxx≤32MHz

fxx=32MHz

fx=16MHz 36 48 mA

All peripherals

stopped

Peripheral: fxx

PRSI option: 0

PLL: ON

12MHz≤fxx≤32MHz

fxx=20MHz

fx=5MHz 22 mA

fxx=32MHz

fx=16MHz 32 mA

PLL: OFF

4MHz≤fxx≤16MHz

fxx=8MHz

8MHz Internal-

OSC Note3

12 mA

fxx=16MHz

fx=16MHz 19 mA

Peripheral: fxx/2

PRSI option: 1

PLL: ON

12MHz≤fxx≤32MHz

fxx=32MHz

fx=16MHz 31 mA

Data Sheet U18567EE1V3DS00

V850ES/FJ3

HALT

mode

Note8

IDD2

All peripherals

running

Peripheral: fxx

PRSI option: 0

PLL: ON

12MHz≤fxx≤32MHz

fxx=20MHz

fx=5MHz 18 26 mA

fxx=32MHz

fx=16MHz 27 39 mA

PLL: OFF

4MHz≤fxx≤16MHz

fxx=8MHz

8MHz Internal-

OSC Note3

812mA

fxx=16MHz

fx=16MHz 13 20 mA

Peripheral: fxx/2

PRSI option: 1

PLL: ON

12MHz≤fxx≤32MHz

fxx=32MHz

fx=16MHz 21 29 mA

All peripherals

stopped

Peripheral: fxx

PRSI option: 0

PLL: ON

12MHz≤fxx≤32MHz

fxx=20MHz

fx=5MHz 12 mA

fxx=32MHz

fx=16MHz 18 mA

PLL: OFF

4MHz≤fxx≤16MHz

fxx=8MHz

8MHz Internal-

OSC Note3

5mA

fxx=16MHz

fx=16MHz 9mA

Peripheral: fxx/2

PRSI option: 1

PLL: ON

12MHz≤fxx≤32MHz

fxx=32MHz

fx=16MHz 18 mA

IDLE1

mode IDD3

Peripheral (TAA, UARTD) run-

ning

PLL: OFF

4MHz≤fxx≤16MHz

Note7

fxx=5MHz

fx=5MHz 1.7 2.7 mA

fxx=12MHz

fx=12MHz 2.7 4.1 mA

fxx=16MHz

fx=16MHz 3.3 5.0 mA

fxx=8MHz, 8MHz Internal-OSCNote3 1.5 2.6 mA

All peripherals stopped

PLL: OFF

4MHz≤fxx≤16MHz

Note7

fxx=5MHz

fx=5MHz 1.2 mA

fxx=12MHz

fx=12MHz 1.4 mA

fxx=16MHz

fx=16MHz 1.6 mA

fxx=8MHz, 8MHz Internal-OSCNote3 1.1 mA

IDLE2

mode IDD4

PLL: OFF

4MHz≤fxx≤16MHz

Note7

fxx=5MHz

fx=5MHz 0.4 0.9 mA

fxx=12MHz

fx=12MHz 0.7 1.2 mA

fxx=16MHz

fx=16MHz 0.8 1.4 mA

fxx=8MHz, 8MHz Internal-OSC Note3 0.2 0.7 mA

SUB

operating

modeNote5

IDD5

RC resonator (fxt=20kHz) Note6 80 600 µA

240 kHz Internal-OSC (SubOSC stopped) 220 1200 µA

SubIDLE

mode IDD6 RC resonator (fxt=20kHz) Note6 40 420 μA

240kHz Internal-OSC (SubOSC stopped) 25 380 μA

STOP

mode

Note3,4

IDD7

POC stop 240kHz Internal-OSC stop 7.5 280 μA

240kHz Internal-OSC working 15.5 295 μA

POC work 240kHz Internal-OSC stop 10.5 285 μA

240kHz Internal-OSC working 18.5 300 μA

Mode Symbol Condition TYP. MAX. Unit

50 Data Sheet U18567EE1V3DS00

V850ES/FJ3

(b) Calculation formulas

(Ta = -40 to +110°C, C=4.7uF,

VDD = EVDD = BVDD = 3.3 to 5.5V, AVREF0 = 3.3 to 5.5V, VSS = EVSS = BVSS = AVSS = 0VNote1)

Notes: 1. VDD, EVDD and BVDD total current. (Ports are stopped).

AVREF0 current, port buffer current (including a current flowing in the on-chip pull-up/pull-

down resistor) are not included.

2. The code flash and the data flash are in read mode.

When the device is in programming mode (Self-programming mode or data flash program-

ming mode), the current value (MAX. value) adds by the following value:

•Self-programming mode:

+ In case of PLL OFF: 7-(0.33*fxx+0.1) [mA]

+ In case of PLL ON: 7-(0.18*fxx+3.0) [mA]

•Data flash programming mode:

+ 7-(0.18*fxx/4+3.0) [mA]

3. Main OSC is stopped.

4. Do not use SubOSC.

5. POC is working. 240kHz Internal-OSC is working. 8MHz Internal-OSC is stopped.

6. RC Oscillation frequency is typ.40kHz. This clock is divided by 2 internally.

7. 8MHz Internal-OSC is stopped

8. When the SSCG is running, the current value adds typ +2.5mA, max +4mA.

9. The formulas are for reference only. Not all possible values for fxx are tested in the outgoing

device inspection.

Mode Symbol Condition TYP. Note9 MAX. Note3 Unit

Operating

mode

Note2,8

IDD1

All peripherals

running

Peripheral: fxx

PRSI option: 0

PLL: ON

12MHz≤fxx≤32MHz 1.03⋅fxx+7.1 1.24⋅fxx+13.6 mA

PLL: OFF

4MHz≤fxx≤16MHz 1.03⋅fxx+5.5 1.24⋅fxx+10.6 mA

Peripheral: fxx/2

PRSI option: 1

PLL: ON

12MHz≤fxx≤32MHz 0.92⋅fxx+6.0 1.11⋅fxx+12.2 mA

All peripherals

stopped

Peripheral: ffxx-

PRSI option: 0

PLL: ON

12MHz≤fxx≤32MHz 0.81⋅fxx+6.2 mA

PLL: OFF

4MHz≤fxx≤16MHz 0.83⋅fxx+5.7 mA

Peripheral: fxx/2

PRSI option: 1

PLL: ON

12MHz≤fxx≤32MHz 0.79⋅fxx+6.2 mA

HALT

mode

Note8

IDD2

All peripherals

running

Peripheral: ffxx-

PRSI option: 0

PLL: ON

16MHz≤fxx≤32MHz 0.75⋅fxx+3.0 1.04*fxx+5.4 mA

PLL: OFF

4MHz≤fxx≤16MHz 0.70⋅fxx+1.9 1.00*fxx+4.0 mA

Peripheral: fxx/2

PRSI option: 1

PLL: ON

16MHz≤fxx≤32MHz 0.56⋅fxx+2.8 0.69*fxx+7.0 mA

All peripherals

stopped

Peripheral: fxx

PRSI option: 0

PLL: ON

16MHz≤fxx≤32MHz 0.46⋅fxx+2.8 mA

PLL: OFF

4MHz≤fxx≤16MHz 0.44⋅fxx+1.6 mA

Peripheral: fxx/2

PRSI option: 1

PLL: ON

16MHz≤fxx≤32MHz 0.46⋅fxx+1.8 mA

IDLE1

mode IDD3

Peripheral (TAA, UARTD) run-

ning

PLL: OFF

4MHz≤fxx≤16MHz

Note7

0.151⋅fxx+0.90 0.209⋅fxx+ 1.63 mA

All peripherals stopped 0.035⋅fxx+1.01 mA

IDLE2

mode IDD4 PLL: OFF

4MHz ≤fxx≤16MHz Note7 0.037⋅fxx+0.21 0.049⋅fxx+ 0.63 mA

Data Sheet U18567EE1V3DS00

V850ES/FJ3

3.6.3.2 µPD70F3379, µPD70F3380

(a) Absolute values

(Ta = -40 to +110°C, C=4.7uF,

VDD = EVDD = BVDD = 3.3 to 5.5V, AVREF0 = 3.3 to 5.5V, VSS = EVSS = BVSS = AVSS = 0VNote1)

Mode Symbol Condition TYP. MAX. Unit

Operating

mode

Note2,8

IDD1

All peripherals

running

Peripheral: fxx

PRSI option: 0

PLL: ON

12MHz≤fxx≤32MHz

fxx=20MHz

fx=5MHz 28 39 mA

fxx=32MHz

fx=16MHz 41 54 mA

PLL: OFF

4MHz≤fxx≤16MHz

fxx=8MHz

8MHz Internal-

OSC Note3

14 21 mA

fxx=16MHz

fx=16MHz 23 31 mA

Peripheral: fxx/2

PRSI option: 1

PLL: ON

12MHz≤fxx≤48MHz

fxx=48MHz

fx=12MHz 51 66 mA

All peripherals

stopped

Peripheral: fxx

PRSI option: 0

PLL: ON

12MHz≤fxx≤32MHz

fxx=20MHz

fx=5MHz 22 mA

fxx=32MHz

fx=16MHz 32 mA

PLL: OFF

4MHz≤fxx≤16MHz

fxx=8MHz

8MHz Internal-

OSC Note3

12 mA

fxx=16MHz

fx=16MHz 19 mA

Peripheral: fxx/2

PRSI option: 1

PLL: ON

12MHz≤fxx≤48MHz

fxx=48MHz

fx=12MHz 44 mA

HALT

mode

Note8

IDD2

All peripherals

running

Peripheral: fxx

PRSI option: 0

PLL: ON

12MHz≤fxx≤32MHz

fxx=20MHz

fx=5MHz 18 26 mA

fxx=32MHz

fx=16MHz 27 39 mA

PLL: OFF

4MHz≤fxx≤16MHz

fxx=8MHz

8MHz Internal-

OSC Note3

812mA

fxx=16MHz

fx=16MHz 13 20 mA

Peripheral: fxx/2

PRSI option: 1

PLL: ON

12MHz≤fxx≤48MHz

fxx=48MHz

fx=12MHz 30 40 mA

All peripherals

stopped

Peripheral: fxx

PRSI option: 0

PLL: ON

12MHz≤fxx≤32MHz

fxx=20MHz

fx=5MHz 12 mA

fxx=32MHz

fx=16MHz 18 mA

PLL: OFF

4MHz≤fxx≤16MHz

fxx=8MHz

8MHz Internal-

OSC Note3

5mA

fxx=16MHz

fx=16MHz 9mA

Peripheral: fxx/2

PRSI option: 1

PLL: ON

12MHz≤fxx≤48MHz

fxx=48MHz

fx=12MHz 24 mA

52 Data Sheet U18567EE1V3DS00

V850ES/FJ3

IDLE1

mode IDD3

Peripheral (TAA, UARTD) run-

ning

PLL: OFF

4MHz≤fxx≤16MHz

Note7

fxx=5MHz

fx=5MHz 1.7 2.7 mA

fxx=12MHz

fx=12MHz 2.7 4.1 mA

fxx=16MHz

fx=16MHz 3.3 5.0 mA

fxx=8MHz, 8MHz Internal-OSCNote3 1.5 2.6 mA

All peripherals stopped

PLL: OFF

4MHz≤fxx≤16MHz

Note7

fxx=5MHz

fx=5MHz 1.2 mA

fxx=12MHz

fx=12MHz 1.4 mA

fxx=16MHz

fx=16MHz 1.6 mA

fxx=8MHz, 8MHz Internal-OSCNote3 1.1 mA

IDLE2

mode IDD4

PLL: OFF

4MHz≤fxx≤16MHz

Note7

fxx=5MHz

fx=5MHz 0.4 0.9 mA

fxx=12MHz

fx=12MHz 0.7 1.2 mA

fxx=16MHz

fx=16MHz 0.8 1.4 mA

fxx=8MHz, 8MHz Internal-OSC Note3 0.2 0.7 mA

SUB

operating

modeNote5

IDD5

RC resonator (fxt=20kHz) Note6 80 600 µA

240 kHz Internal-OSC (SubOSC stopped) 220 1200 µA

SubIDLE

mode

Note3,5

IDD6

RC resonator (fxt=20kHz) Note6 40 420 μA

240kHz Internal-OSC (SubOSC stopped) 25 380 μA

STOP

mode

Note3,4

IDD7

POC stop 240kHz Internal-OSC stop 7.5 290 μA

240kHz Internal-OSC working 15.5 305 μA

POC work 240kHz Internal-OSC stop 10.5 295 μA

240kHz Internal-OSC working 18.5 310 μA

Mode Symbol Condition TYP. MAX. Unit

Data Sheet U18567EE1V3DS00

V850ES/FJ3

(b) Calculation formulas

(Ta = -40 to +110°C, C=4.7uF,

VDD = EVDD = BVDD = 3.3 to 5.5V, AVREF0 = 3.3 to 5.5V, VSS = EVSS = BVSS = AVSS = 0VNote1)

Notes: 1. VDD, EVDD and BVDD total current. (Ports are stopped).

AVREF0 current, port buffer current (including a current flowing in the on-chip pull-up/pull-

down resistor) are not included.

2. The code flash and the data flash are in read mode.

When the device is in programming mode (Self-programming mode or data flash program-

ming mode), the current value (MAX. value) adds by the following value:

•Self-programming mode:

+ In case of PLL OFF: 7-(0.33*fxx+0.1) [mA]

+ In case of PLL ON: 7-(0.18*fxx+3.0) [mA]

•Data flash programming mode:

+ 7-(0.18*fxx/4+3.0) [mA]

3. Main OSC is stopped.

4. Do not use SubOSC.

5. POC is working. 240kHz Internal-OSC is working. 8MHz Internal-OSC is stopped.

6. RC Oscillation frequency is typ.40kHz. This clock is divided by 2 internally.

7. 8MHz Internal-OSC is stopped

8. When the SSCG is running, the current value adds typ +2.5mA, max +4mA.

9. The formulas are for reference only. Not all possible values for fxx are tested in the outgoing

device inspection.

Mode Symbol Condition TYP. Note9 MAX. Note3 Unit

Operating

mode

Note2,8

IDD1

All peripherals

running

Peripheral: fxx

PRSI option: 0

PLL: ON

12MHz≤fxx≤32MHz 1.06⋅fxx+7.1 1.27⋅fxx+13.6 mA

PLL: OFF

4MHz≤fxx≤16MHz 1.06⋅fxx+5.5 1.28⋅fxx+10.6 mA

Peripheral: fxx/2

PRSI option: 1

PLL: ON

12MHz≤fxx≤48MHz 0.94⋅fxx+6.0 1.13⋅fxx+12.2 mA

All peripherals

stopped

Peripheral: ffxx-

PRSI option: 0

PLL: ON

12MHz≤fxx≤32MHz 0.81⋅fxx+6.2 mA

PLL: OFF

4MHz≤fxx≤16MHz 0.83⋅fxx+5.7 mA

Peripheral: fxx/2

PRSI option: 1

PLL: ON

12MHz≤fxx≤48MHz 0.79⋅fxx+6.2 mA

HALT

mode

Note8

IDD2

All peripherals

running

Peripheral: ffxx-

PRSI option: 0

PLL: ON

16MHz≤fxx≤32MHz 0.75⋅fxx+3.0 1.04*fxx+5.4 mA

PLL: OFF

4MHz≤fxx≤16MHz 0.70⋅fxx+1.9 1.00*fxx+4.0 mA

Peripheral: fxx/2

PRSI option: 1

PLL: ON

16MHz≤fxx≤48MHz 0.56⋅fxx+2.8 0.69*fxx+7.0 mA

All peripherals

stopped

Peripheral: fxx

PRSI option: 0

PLL: ON

16MHz≤fxx≤32MHz 0.46⋅fxx+2.8 mA

PLL: OFF

4MHz≤fxx≤16MHz 0.44⋅fxx+1.6 mA

Peripheral: fxx/2

PRSI option: 1

PLL: ON

16MHz≤fxx≤48MHz 0.46⋅fxx+1.8 mA

IDLE1

mode IDD3

Peripheral (TAA, UARTD) run-

ning

PLL: OFF

4MHz≤fxx≤16MHz

Note7

0.151⋅fxx+0.90 0.209⋅fxx+ 1.63 mA

All peripherals stopped 0.035⋅fxx+1.01 mA

IDLE2

mode IDD4 PLL: OFF

4MHz ≤fxx≤16MHz Note7 0.037⋅fxx+0.21 0.049⋅fxx+ 0.63 mA

54 Data Sheet U18567EE1V3DS00

V850ES/FJ3

3.6.3.3 µPD70F3381, µPD70F3382

(a) Absolute values

(Ta = -40 to +110°C, C=4.7uF,

VDD = EVDD = BVDD = 3.3 to 5.5V, AVREF0 = 3.3 to 5.5V, VSS = EVSS = BVSS = AVSS = 0VNote1)

Mode Symbol Condition TYP. MAX. Unit

Operating

mode

Note2,8

IDD1

All peripherals

running

Peripheral: fxx

PRSI option: 0

PLL: ON

12MHz≤fxx≤32MHz

fxx=20MHz

fx=5MHz 30 41 mA

fxx=32MHz

fx=16MHz 43 57 mA

PLL: OFF

4MHz≤fxx≤16MHz

fxx=8MHz

8MHz Internal-

OSC Note3

15 22 mA

fxx=16MHz

fx=16MHz 24 32 mA

Peripheral: fxx/2

PRSI option: 1

PLL: ON

12MHz≤fxx≤48MHz

fxx=48MHz

fx=12MHz 53 68 mA

All peripherals

stopped

Peripheral: fxx

PRSI option: 0

PLL: ON

12MHz≤fxx≤32MHz

fxx=20MHz

fx=5MHz 23 mA

fxx=32MHz

fx=16MHz 33 mA

PLL: OFF

4MHz≤fxx≤16MHz

fxx=8MHz

8MHz Internal-

OSC Note3

13 mA

fxx=16MHz

fx=16MHz 19 mA

Peripheral: fxx/2

PRSI option: 1

PLL: ON

12MHz≤fxx≤48MHz

fxx=48MHz

fx=12MHz 46 mA

HALT

mode

Note8

IDD2

All peripherals

running

Peripheral: fxx

PRSI option: 0

PLL: ON

12MHz≤fxx≤32MHz

fxx=20MHz

fx=5MHz 19 28 mA

fxx=32MHz

fx=16MHz 28 40 mA

PLL: OFF

4MHz≤fxx≤16MHz

fxx=8MHz

8MHz Internal-

OSC Note3

914mA

fxx=16MHz

fx=16MHz 15 22 mA

Peripheral: fxx/2

PRSI option: 1

PLL: ON

12MHz≤fxx≤48MHz

fxx=48MHz

fx=12MHz 31 42 mA

All peripherals

stopped

Peripheral: fxx

PRSI option: 0

PLL: ON

12MHz≤fxx≤32MHz

fxx=20MHz

fx=5MHz 13 mA

fxx=32MHz

fx=16MHz 18 mA

PLL: OFF

4MHz≤fxx≤16MHz

fxx=8MHz

8MHz Internal-

OSC Note3

6mA

fxx=16MHz

fx=16MHz 10 mA

Peripheral: fxx/2

PRSI option: 1

PLL: ON

12MHz≤fxx≤48MHz

fxx=48MHz

fx=12MHz 25 mA

Data Sheet U18567EE1V3DS00

V850ES/FJ3

IDLE1

mode IDD3

Peripheral (TAA, UARTD) run-

ning

PLL: OFF

4MHz≤fxx≤16MHz

Note7

fxx=5MHz

fx=5MHz 2.6 3.6 mA

fxx=12MHz

fx=12MHz 4.1 5.6 mA

fxx=16MHz

fx=16MHz 4.9 6.8 mA

fxx=8MHz, 8MHz Internal-OSCNote3 3.0 4.2 mA

All peripherals stopped

PLL: OFF

4MHz≤fxx≤16MHz

Note7

fxx=5MHz

fx=5MHz 1.4 mA

fxx=12MHz

fx=12MHz 1.8 mA

fxx=16MHz

fx=16MHz 2.0 mA

fxx=8MHz, 8MHz Internal-OSCNote3 1.3 mA

IDLE2

mode IDD4

PLL: OFF

4MHz≤fxx≤16MHz

Note7

fxx=5MHz

fx=5MHz 0.4 0.9 mA

fxx=12MHz

fx=12MHz 0.7 1.2 mA

fxx=16MHz

fx=16MHz 0.8 1.4 mA

fxx=8MHz, 8MHz Internal-OSC Note3 0.2 0.7 mA

SUB

operating

modeNote5

IDD5

RC resonator (fxt=20kHz) Note6 90 600 µA

240 kHz Internal-OSC (SubOSC stopped) 330 1510 µA

SubIDLE

mode

Note3,5

IDD6

RC resonator (fxt=20kHz) Note6 40 420 μA

240kHz Internal-OSC (SubOSC stopped) 25 380 μA

STOP

mode

Note3,4

IDD7

POC stop 240kHz Internal-OSC stop 7.5 300 μA

240kHz Internal-OSC working 15.5 315 μA

POC work 240kHz Internal-OSC stop 10.5 305 μA

240kHz Internal-OSC working 18.5 320 μA

Mode Symbol Condition TYP. MAX. Unit

56 Data Sheet U18567EE1V3DS00

V850ES/FJ3

(b) Calculation formulas

(Ta = -40 to +110°C, C=4.7uF,

VDD = EVDD = BVDD = 3.3 to 5.5V, AVREF0 = 3.3 to 5.5V, VSS = EVSS = BVSS = AVSS = 0VNote1)

Notes: 1. VDD, EVDD and BVDD total current. (Ports are stopped).

AVREF0 current, port buffer current (including a current flowing in the on-chip pull-up/pull-

down resistor) are not included.

2. The code flash and the data flash are in read mode.

When the device is in programming mode (Self-programming mode or data flash program-

ming mode), the current value (MAX. value) adds by the following value:

•Self-programming mode:

+ In case of PLL OFF: 7-(0.33*fxx+0.1) [mA]

+ In case of PLL ON: 7-(0.18*fxx+3.0) [mA]

•Data flash programming mode:

+ 7-(0.18*fxx/4+3.0) [mA]

3. Main OSC is stopped.

4. Do not use SubOSC.

5. POC is working. 240kHz Internal-OSC is working. 8MHz Internal-OSC is stopped.

6. RC Oscillation frequency is typ.40kHz. This clock is divided by 2 internally.

7. 8MHz Internal-OSC is stopped

8. When the SSCG is running, the current value adds typ +2.5mA, max +4mA.

9. The formulas are for reference only. Not all possible values for fxx are tested in the outgoing

device inspection.

Mode Symbol Condition TYP. Note9 MAX. Note3 Unit

Operating

mode

Note2,8

IDD1

All peripherals

running

Peripheral: fxx

PRSI option: 0

PLL: ON

12MHz≤fxx≤32MHz 1.12⋅fxx+7.1 1.35⋅fxx+13.6 mA

PLL: OFF

4MHz≤fxx≤16MHz 1.13⋅fxx+5.5 1.35⋅fxx+10.6 mA

Peripheral: fxx/2

PRSI option: 1

PLL: ON

12MHz≤fxx≤48MHz 0.97⋅fxx+6.0 1.35⋅fxx+12.2 mA

All peripherals

stopped

Peripheral: ffxx-

PRSI option: 0

PLL: ON

12MHz≤fxx≤32MHz 0.85⋅fxx+6.2 mA

PLL: OFF

4MHz≤fxx≤16MHz 0.86⋅fxx+5.7 mA

Peripheral: fxx/2

PRSI option: 1

PLL: ON

12MHz≤fxx≤48MHz 0.82⋅fxx+6.2 mA

HALT

mode

Note8

IDD2

All peripherals

running

Peripheral: ffxx-

PRSI option: 0

PLL: ON

16MHz≤fxx≤32MHz 0.75⋅fxx+3.8 1.04*fxx+6.9 mA

PLL: OFF

4MHz≤fxx≤16MHz 0.72⋅fxx+3.0 1.00*fxx+5.5 mA

Peripheral: fxx/2

PRSI option: 1

PLL: ON

16MHz≤fxx≤48MHz 0.56⋅fxx+4.0 0.69*fxx+8.5 mA

All peripherals

stopped

Peripheral: fxx

PRSI option: 0

PLL: ON

16MHz≤fxx≤32MHz 0.46⋅fxx+2.6 mA

PLL: OFF

4MHz≤fxx≤16MHz 0.46⋅fxx+3.6 mA

Peripheral: fxx/2

PRSI option: 1

PLL: ON

16MHz≤fxx≤48MHz 0.46⋅fxx+2.8 mA

IDLE1

mode IDD3

Peripheral (TAA, UARTD) run-

ning

PLL: OFF

4MHz≤fxx≤16MHz

Note7

0.211⋅fxx+1.54 0.295⋅fxx+ 2.10 mA

All peripherals stopped 0.054⋅fxx+1.15 mA

IDLE2

mode IDD4 PLL: OFF

4MHz ≤fxx≤16MHz Note7 0.037⋅fxx+0.21 0.049⋅fxx+ 0.63 mA

Data Sheet U18567EE1V3DS00

V850ES/FJ3

3.7 AC Characteristics

AC test Input measurement points ( VDD, AVREF0, EVDD, BVDD)

AC test output measurement points

Load conditions

Caution: If the load capacitance exceeds 50pF due to the circuit configuration, reduce the load

capacitance of the device to 50pF or less by inserting a buffer or by some other means.

3.7.1 CLKOUT Output Timing

Specification is identical to that from (A)-Grade except Ta=-40 to +110°C.

3.7.2 Bus Timing (Multiplexed bus mode)

Specification is identical to that from (A)-Grade except Ta=-40 to +110°C.

3.7.3 RESET, Interrupt, ADTRG Timing

Specification is identical to that from (A)-Grade except Ta=-40 to +110°C.

3.7.4 Key Return Timing

Specification is identical to that from (A)-Grade except Ta=-40 to +110°C.

3.7.5 Timer Timing

Specification is identical to that from (A)-Grade except Ta=-40 to +110°C.

3.7.6 CSI Timing

Specification is identical to that from (A)-Grade except Ta=-40 to +110°C.

3.7.7 UART Timing

Specification is identical to that from (A)-Grade except Ta=-40 to +110°C.

3.7.8 IIC Timing

Specification is identical to that from (A)-Grade except Ta=-40 to +110°C.

measure point

VIH(min)

VIL(max)

VIH(min)

VIL(max)

VDD

VSS

measure point

VOH(min)

VOL(max)

VOH(min)

VOL(max)

CL = 50 pF

DUT

( Device under

test )

58 Data Sheet U18567EE1V3DS00

V850ES/FJ3

3.7.9 CAN Timing

Specification is identical to that from (A)-Grade except Ta=-40 to +110°C.

3.8 A/D Converter

Specification is identical to that from (A)-Grade except Ta=-40 to +110°C.

3.9 POC

Specification is identical to that from (A)-Grade except Ta=-40 to +110°C.

3.10 LVI

Specification is identical to that from (A)-Grade except Ta=-40 to +110°C.

3.11 RAM Retention Flag

Specification is identical to that from (A)-Grade except Ta=-40 to +110°C.

3.12 Data Retention Characteristics

Specification is identical to that from (A)-Grade except Ta=-40 to +110°C.

3.13 Flash Memory Programming Characteristics

(a) Basic Characteristics

(C=4.7uF, VDD = EVDD = BVDD, AVREF0 = 3.5 to 5.5V, VSS = EVSS = BVSS = AVSS = 0V)

Notes: 1. Under the condition of CWRT1

2. Under the condition of CWRT2

Remark: The initial write when the product is shipped, any erase → write set of operations, or any

programming operation is counted as one rewrite.

Example: P: Program(write) E: Erase

Product is shipped → P → E → P → E → P : Rewrite count: 3

Product is shipped → E → P → E → P → E → P : Rewrite count: 3

(b) Serial Writing Operation Characteristics

Specification is identical to that from (A)-Grade except Ta=-40 to +110°C.

Parameter Symbol Conditions MIN. TYP. MAX. Unit

Operation frequency fCPU ≤256KB product 4 32 MHz

≥384KB product 4 48

Supply voltage VDD 3.3 5.5 V

Number of rewrites CWRT1 Code Flash 1000 count

Data Flash

CWRT2 10000

High level input voltage VIH FLMD0 0.8EVDD EVDD V

Low level input voltage VIL FLMD0 EVSS 0.2EVDD V

Programming temperature tPRG -40 +110 °C

Data retention

Code Flash 15Note1

year

Data Flash 5Note2

Data Sheet U18567EE1V3DS00

V850ES/FJ3

4. Electrical Specifications of (A2)-Grade

This product has to be used only under the conditions of VDD=EVDD=BVDD. Operation is not ensured

at the time of using this product except this condition.

4.1 Absolute Maximum Ratings

Specification is identical to that from (A1)-Grade except

•Operating ambient temperature Ta = -40 to +125°C

•Note2: AVREF0 IOH/IOL current is including ADC max. current IAREF0.

4.2 Capacities

Specification is identical to that from (A)-Grade except Ta=-40 to +125°C.

60 Data Sheet U18567EE1V3DS00

V850ES/FJ3

4.3 Operating condition

(Ta = -40 to +125°C, C=4.7uF, VDD = EVDD = BVDD = 3.3 to 5.5V, AVREF0 = 3.3 to 5.5V, VSS = EVSS = BVSS = AVSS = 0V)

Notes: 1. For using SSCG please refer to ’4.5.5 SSCG Characteristics’ for details

2. VDD = EVDD = BVDD

3. RC Oscillation frequency is min. 25kHz max. 55kHz. This clock is divided by 2 internally.

4.4 Voltage Regulator Characteristics

Specification is identical to that from (A)-Grade except Ta=-40 to +125°C.

4.5 Clock Generator Circuit

4.5.1 Main System Clock Oscillation Circuit Characteristics

Specification is identical to that from (A)-Grade except Ta=-40 to +125°C.

Internal System clock frequency (fVBCLK)Supply voltage Operating Condition

4.0≤fxx≤24MHz (≤256KB product)

4.0≤fxx≤32MHz (≥384KB product)

Note1

4.0V≤VDD≤5.5VNote2

Operation of functions is usable under following

conditions:

•Peripheral clock frequency

•fXP1 ≤ fXX

•fXP2 ≤ fXX

•AC characteristics:

•Refer to chapter ’4.7 AC Characteris-

tics’ for details.

3.5V≤VDD<4.0VNote2

Operation of functions is usable under following

conditions:

•Peripheral clock frequency

•fXP1 ≤ 20MHz

•fXP2 ≤ 20MHz

•AC characteristics:

•Refer to chapter ’4.7 AC Characteris-

tics’ for details.

3.3V≤VDD<3.5VNote2

Only operation of the following functions is

assured:

•CPU

•Flash (include programming)

•RAM

•IO Buffer

•Port

•WT

•WDT

•INT

•CLM

•POC

•LVI

3.3V≤AVREF0≤5.5V

•A/D Converter

•Refer to chapter ’4.8 A/D Converter’ for

details.

•stop ADC for AVREF0 < 4.0V

(ADA0CE bit =0)

12.5kHz≤fXT≤27.5kHz Note3(RC) 3.3V≤VDD<5.5VNote2 -

fRL (240kHz Internal-OSC) 3.3V≤VDD<5.5VNote2 -

Data Sheet U18567EE1V3DS00

V850ES/FJ3

4.5.2 Sub System Clock Oscillation Circuit Characteristics

Specification is identical to that from (A1)-Grade except Ta=-40 to +125°C.

4.5.3 Internal-OSC Characteristics

Specification is identical to that from (A)-Grade except Ta=-40 to +125°C.

4.5.4 PLL Characteristics

(Ta = -40 to +125°C, C=4.7uF, VDD = EVDD = BVDD = 3.3 to 5.5V, AVREF0 = 3.3 to 5.5V, VSS = EVSS = BVSS = AVSS = 0V)

Notes: 1. The input of the PLL (fPLLI) can be set to fX, fX/2, or fX/4. The divider is set through an option

byte in the code flash memory.

2. Not tested in production.

4.5.5 SSCG Characteristics

(Ta = -40 to +125°C, C=4.7uF, VDD = EVDD = BVDD = 3.3 to 5.5V, AVREF0 = 3.3 to 5.5V, VSS = EVSS = BVSS = AVSS = 0V)

Remark: The SSCG MAX output frequency indicates the case without modulation. If modulation is

enabled the average SSCG frequency has to be set lower. The maximum achievable aver-

age operating frequency with modulation is as follows:

Parameter Symbol Conditions MIN. TYP. MAX. Unit

Input frequency fx 4 16 MHz

fPLLI Note 36MHz

Output frequency fxx ≤256KB product 12 24 MHz

≥384KB product 12 32

Lock time tPLL After VDD reaches voltage range min. 3.3V 800 μs

Output period jitter

Note2 tpj Peak to peak 2.0 ns

Parameter Symbol Conditions MIN. TYP. MAX. Unit

Input frequency fx 4 16 MHz

Output frequency fxx ≤256KB product 12 24 MHz

≥384KB product 12 32

Lock time tSSCG After VDD reaches voltage range min. 3.3V 1000 μs

SSCG input clock divider selector

SFC1[6:4]

Percent modulation Maximum average operating fre-

quency Unit

TYP MAX ≤256KB product ≥384KB product

000B ± 0.5% ± 2.0% 23.5 31.4

MHz

001B ± 1.0% ± 2.5% 23.4 31.2

010B ± 2.0% ± 4.0% 23.0 30.7

011B ± 3.0% ± 6.0% 22.6 30.1

100B ± 4.0% ± 8.0% 22.1 29.4

101B ± 5.0% ± 10.0% 21.6 28.8

62 Data Sheet U18567EE1V3DS00

V850ES/FJ3

4.6 DC Characteristics

4.6.1 Input/Output Level

Specification is identical to that from (A1)-Grade except

•Ta = -40 to +125°C.

• Note 2:Total IOH/IOL max is 20mA/-20mA for the power supply lines EVDD and BVDD.

Total IOH/IOL max is 3mA/-3mA for the power supply line AVREF0.

AVREF0 IOH/IOL current is excluding ADC current IAREF0.

If ADC0 is not used total IOH/IOL max is 10mA/-10mA for the power supply line AVREF0.

4.6.2 PIN leakage current

(Ta = -40 to +125°C, C=4.7uF, VDD = EVDD = BVDD = 3.3 to 5.5V, AVREF0 = 3.3 to 5.5V, VSS = EVSS = BVSS = AVSS = 0V)

Notes: 1. The input leakage current of FLMD0 is as follows:

High level input leakage current: 5.0uA

Low level input leakage current: -5.0uA

Parameter Symbol Conditions MIN. TYP. MAX. Unit

High level input

leakage current ILIH1 VI=VDD Analog pins 0.5

Other pins Note1 1.0

Low level input

leakage current ILIL1 VI=0V Analog pins -0.5

Other pins Note1 -1.0

High level output

leakage current ILOH1 VO=VDD Analog pins 0.5

Other pins 1.0

Low level output

leakage current ILOL1 VO=0V Analog pins -0.5

Other pins -1.0

Data Sheet U18567EE1V3DS00

V850ES/FJ3

4.6.3 Power supply current (A2-grade)

4.6.3.1 µPD70F3378

(a) Absolute values

(Ta = -40 to +125°C, C=4.7uF,

VDD = EVDD = BVDD = 3.3 to 5.5V, AVREF0 = 3.3 to 5.5V, VSS = EVSS = BVSS = AVSS = 0VNote1)

Mode Symbol Condition TYP. MAX. Unit

Operating

mode

Note2,8

IDD1

All peripherals

running

Peripheral: fxx

PRSI option: 0

PLL: ON

12MHz≤fxx≤24MHz

fxx=20MHz

fx=5MHz 28 38 mA

PLL: OFF

4MHz≤fxx≤16MHz

fxx=8MHz

8MHz Internal-

OSC Note3

14 21 mA

fxx=16MHz

fx=16MHz 22 30 mA

All peripherals

stopped

Peripheral: fxx

PRSI option: 0

PLL: ON

12MHz≤fxx≤24MHz

fxx=20MHz

fx=5MHz 22 mA

PLL: OFF

4MHz≤fxx≤16MHz

fxx=8MHz

8MHz Internal-

OSC Note3

12 mA

fxx=16MHz

fx=16MHz 19 mA

HALT

mode

Note8

IDD2

All peripherals

running

Peripheral: fxx

PRSI option: 0

PLL: ON

12MHz≤fxx≤24MHz

fxx=20MHz

fx=5MHz 18 26 mA

PLL: OFF

4MHz≤fxx≤16MHz

fxx=8MHz

8MHz Internal-

OSC Note3

812mA

fxx=16MHz

fx=16MHz 13 20 mA

All peripherals

stopped

Peripheral: fxx

PRSI option: 0

PLL: ON

12MHz≤fxx≤24MHz

fxx=20MHz

fx=5MHz 12 mA

PLL: OFF

4MHz≤fxx≤16MHz

fxx=8MHz

8MHz Internal-

OSC Note3

5mA

fxx=16MHz

fx=16MHz 9mA

IDLE1

mode IDD3

Peripheral (TAA, UARTD) run-

ning

PLL: OFF

4MHz≤fxx≤16MHz

Note7

fxx=5MHz

fx=5MHz 1.7 3.0 mA

fxx=12MHz

fx=12MHz 2.7 4.4 mA

fxx=16MHz

fx=16MHz 3.3 5.3 mA

fxx=8MHz, 8MHz Internal-OSCNote3 1.5 2.9 mA

All peripherals stopped

PLL: OFF

4MHz≤fxx≤16MHz

Note7

fxx=5MHz

fx=5MHz 1.2 mA

fxx=12MHz

fx=12MHz 1.4 mA

fxx=16MHz

fx=16MHz 1.6 mA

fxx=8MHz, 8MHz Internal-OSCNote3 1.1 mA

64 Data Sheet U18567EE1V3DS00

V850ES/FJ3

IDLE2

mode IDD4

PLL: OFF

4MHz≤fxx≤16MHz

Note7

fxx=5MHz

fx=5MHz 0.4 1.1 mA

fxx=12MHz

fx=12MHz 0.7 1.5 mA

fxx=16MHz

fx=16MHz 0.8 1.7 mA

fxx=8MHz, 8MHz Internal-OSC Note3 0.2 1.0 mA

SUB

operating

modeNote5

IDD5

RC resonator (fxt=20kHz) Note6 80 850 µA

240 kHz Internal-OSC (SubOSC stopped) 220 1450 µA

SubIDLE

mode

Note3,5

IDD6

RC resonator (fxt=20kHz) Note6 40 670 μA

240kHz Internal-OSC (SubOSC stopped) 25 630 μA

STOP

mode

Note3,4

IDD7

POC stop 240kHz Internal-OSC stop 7.5 530 μA

240kHz Internal-OSC working 15.5 545 μA

POC work 240kHz Internal-OSC stop 10.5 535 μA

240kHz Internal-OSC working 18.5 550 μA

Mode Symbol Condition TYP. MAX. Unit

Data Sheet U18567EE1V3DS00

V850ES/FJ3

(b) Calculation formulas

(Ta = -40 to +125°C, C=4.7uF,

VDD = EVDD = BVDD = 3.3 to 5.5V, AVREF0 = 3.3 to 5.5V, VSS = EVSS = BVSS = AVSS = 0VNote1)

Notes: 1. VDD, EVDD and BVDD total current. (Ports are stopped).

AVREF0 current, port buffer current (including a current flowing in the on-chip pull-up/pull-

down resistor) are not included.

2. The code flash and the data flash are in read mode.

When the device is in programming mode (Self-programming mode or data flash program-

ming mode), the current value (MAX. value) adds by the following value:

•Self-programming mode:

+ In case of PLL OFF: 7-(0.33*fxx+0.1) [mA]

+ In case of PLL ON: 7-(0.18*fxx+3.0) [mA]

•Data flash programming mode:

+ 7-(0.18*fxx/4+3.0) [mA]

3. Main OSC is stopped.

4. Do not use SubOSC.

5. POC is working. 240kHz Internal-OSC is working. 8MHz Internal-OSC is stopped.

6. RC Oscillation frequency is typ.40kHz. This clock is divided by 2 internally.

7. 8MHz Internal-OSC is stopped

8. When the SSCG is running, the current value adds typ +2.5mA, max +4mA.

9. The formulas are for reference only. Not all possible values for fxx are tested in the outgoing

device inspection.

Mode Symbol Condition TYP. Note9 MAX. Note3 Unit

Operating

mode

Note2,8

IDD1

All peripherals

running

Peripheral: fxx

PRSI option: 0

PLL: ON

12MHz≤fxx≤24MHz 1.03⋅fxx+7.1 1.24⋅fxx+13.6 mA

PLL: OFF

4MHz≤fxx≤16MHz 1.03⋅fxx+5.5 1.24⋅fxx+10.6 mA

Peripheral: fxx/2

PRSI option: 1

PLL: ON

12MHz≤fxx≤24MHz 0.92⋅fxx+6.0 1.11⋅fxx+12.2 mA

All peripherals

stopped

Peripheral: ffxx-

PRSI option: 0

PLL: ON

12MHz≤fxx≤24MHz 0.81⋅fxx+6.2 mA

PLL: OFF

4MHz≤fxx≤16MHz 0.83⋅fxx+5.7 mA

Peripheral: fxx/2

PRSI option: 1

PLL: ON

12MHz≤fxx≤24MHz 0.79⋅fxx+6.2 mA

HALT

mode

Note8

IDD2

All peripherals

running

Peripheral: ffxx-

PRSI option: 0

PLL: ON

16MHz≤fxx≤24MHz 0.75⋅fxx+3.0 1.04*fxx+5.4 mA

PLL: OFF

4MHz≤fxx≤16MHz 0.70⋅fxx+1.9 1.00*fxx+4.0 mA

Peripheral: fxx/2

PRSI option: 1

PLL: ON

16MHz≤fxx≤24MHz 0.56⋅fxx+2.8 0.69*fxx+7.0 mA

All peripherals

stopped

Peripheral: fxx

PRSI option: 0

PLL: ON

16MHz≤fxx≤24MHz 0.46⋅fxx+2.8 mA

PLL: OFF

4MHz≤fxx≤16MHz 0.44⋅fxx+1.6 mA

Peripheral: fxx/2

PRSI option: 1

PLL: ON

16MHz≤fxx≤24MHz 0.46⋅fxx+1.8 mA

IDLE1

mode IDD3

Peripheral (TAA, UARTD) run-

ning

PLL: OFF

4MHz≤fxx≤16MHz

Note7

0.151⋅fxx+0.90 0.209⋅fxx+ 1.93 mA

All peripherals stopped 0.035⋅fxx+1.01 mA

IDLE2

mode IDD4 PLL: OFF

4MHz ≤fxx≤16MHz Note7 0.037⋅fxx+0.21 0.049⋅fxx+ 0.88 mA

66 Data Sheet U18567EE1V3DS00

V850ES/FJ3

4.6.3.2 µPD70F3379, µPD70F3380

(a) Absolute values

(Ta = -40 to +125°C, C=4.7uF,

VDD = EVDD = BVDD = 3.3 to 5.5V, AVREF0 = 3.3 to 5.5V, VSS = EVSS = BVSS = AVSS = 0VNote1)

Mode Symbol Condition TYP. MAX. Unit

Operating

mode

Note2,8

IDD1

All peripherals

running

Peripheral: fxx

PRSI option: 0

PLL: ON

12MHz≤fxx≤32MHz

fxx=20MHz

fx=5MHz 28 39 mA

fxx=32MHz

fx=16MHz 41 54 mA

PLL: OFF

4MHz≤fxx≤16MHz

fxx=8MHz

8MHz Internal-

OSC Note3

14 21 mA

fxx=16MHz

fx=16MHz 23 31 mA

All peripherals

stopped

Peripheral: fxx

PRSI option: 0

PLL: ON

12MHz≤fxx≤32MHz

fxx=20MHz

fx=5MHz 22 mA

fxx=32MHz

fx=16MHz 32 mA

PLL: OFF

4MHz≤fxx≤16MHz

fxx=8MHz

8MHz Internal-

OSC Note3

12 mA

fxx=16MHz

fx=16MHz 19 mA

HALT

mode

Note8

IDD2

All peripherals

running

Peripheral: fxx

PRSI option: 0

PLL: ON

12MHz≤fxx≤32MHz

fxx=20MHz

fx=5MHz 18 26 mA

fxx=32MHz

fx=16MHz 27 39 mA

PLL: OFF

4MHz≤fxx≤16MHz

fxx=8MHz

8MHz Internal-

OSC Note3

812mA

fxx=16MHz

fx=16MHz 13 20 mA

All peripherals

stopped

Peripheral: fxx

PRSI option: 0

PLL: ON

12MHz≤fxx≤32MHz

fxx=20MHz

fx=5MHz 12 mA

fxx=32MHz

fx=16MHz 18 mA

PLL: OFF

4MHz≤fxx≤16MHz

fxx=8MHz

8MHz Internal-

OSC Note3

5mA

fxx=16MHz

fx=16MHz 9mA

Data Sheet U18567EE1V3DS00

V850ES/FJ3

IDLE1

mode IDD3

Peripheral (TAA, UARTD) run-

ning

PLL: OFF

4MHz≤fxx≤16MHz

Note7

fxx=5MHz

fx=5MHz 1.7 3.0 mA

fxx=12MHz

fx=12MHz 2.7 4.4 mA

fxx=16MHz

fx=16MHz 3.3 5.3 mA

fxx=8MHz, 8MHz Internal-OSCNote3 1.5 2.9 mA

All peripherals stopped

PLL: OFF

4MHz≤fxx≤16MHz

Note7

fxx=5MHz

fx=5MHz 1.2 mA

fxx=12MHz

fx=12MHz 1.4 mA

fxx=16MHz

fx=16MHz 1.6 mA

fxx=8MHz, 8MHz Internal-OSCNote3 1.1 mA

IDLE2

mode IDD4

PLL: OFF

4MHz≤fxx≤16MHz

Note7

fxx=5MHz

fx=5MHz 0.4 1.1 mA

fxx=12MHz

fx=12MHz 0.7 1.5 mA

fxx=16MHz

fx=16MHz 0.8 1.7 mA

fxx=8MHz, 8MHz Internal-OSC Note3 0.2 1.0 mA

SUB

operating

modeNote5

IDD5

RC resonator (fxt=20kHz) Note6 80 850 µA

240 kHz Internal-OSC (SubOSC stopped) 220 1450 µA

SubIDLE

mode

Note3,5

IDD6

RC resonator (fxt=20kHz) Note6 40 670 μA

240kHz Internal-OSC (SubOSC stopped) 25 630 μA

STOP

mode

Note3,4

IDD7

POC stop 240kHz Internal-OSC stop 7.5 540 μA

240kHz Internal-OSC working 15.5 555 μA

POC work 240kHz Internal-OSC stop 10.5 545 μA

240kHz Internal-OSC working 18.5 560 μA

Mode Symbol Condition TYP. MAX. Unit

68 Data Sheet U18567EE1V3DS00

V850ES/FJ3

(b) Calculation formulas

(Ta = -40 to +125°C, C=4.7uF,

VDD = EVDD = BVDD = 3.3 to 5.5V, AVREF0 = 3.3 to 5.5V, VSS = EVSS = BVSS = AVSS = 0VNote1)

Notes: 1. VDD, EVDD and BVDD total current. (Ports are stopped).

AVREF0 current, port buffer current (including a current flowing in the on-chip pull-up/pull-

down resistor) are not included.

2. The code flash and the data flash are in read mode.

When the device is in programming mode (Self-programming mode or data flash program-

ming mode), the current value (MAX. value) adds by the following value:

•Self-programming mode:

+ In case of PLL OFF: 7-(0.33*fxx+0.1) [mA]

+ In case of PLL ON: 7-(0.18*fxx+3.0) [mA]

•Data flash programming mode:

+ 7-(0.18*fxx/4+3.0) [mA]

3. Main OSC is stopped.

4. Do not use SubOSC.

5. POC is working. 240kHz Internal-OSC is working. 8MHz Internal-OSC is stopped.

6. RC Oscillation frequency is typ.40kHz. This clock is divided by 2 internally.

7. 8MHz Internal-OSC is stopped

8. When the SSCG is running, the current value adds typ +2.5mA, max +4mA.

9. The formulas are for reference only. Not all possible values for fxx are tested in the outgoing

device inspection.

Mode Symbol Condition TYP. Note9 MAX. Note3 Unit

Operating

mode

Note2,8

IDD1

All peripherals

running

Peripheral: fxx

PRSI option: 0

PLL: ON

12MHz≤fxx≤32MHz 1.06⋅fxx+7.1 1.27⋅fxx+13.6 mA

PLL: OFF

4MHz≤fxx≤16MHz 1.06⋅fxx+5.5 1.28⋅fxx+10.6 mA

Peripheral: fxx/2

PRSI option: 1

PLL: ON

12MHz≤fxx≤32MHz 0.94⋅fxx+6.0 1.13⋅fxx+12.2 mA

All peripherals

stopped

Peripheral: ffxx-

PRSI option: 0

PLL: ON

12MHz≤fxx≤32MHz 0.81⋅fxx+6.2 mA

PLL: OFF

4MHz≤fxx≤16MHz 0.83⋅fxx+5.7 mA

Peripheral: fxx/2

PRSI option: 1

PLL: ON

12MHz≤fxx≤32MHz 0.79⋅fxx+6.2 mA

HALT

mode

Note8

IDD2

All peripherals

running

Peripheral: ffxx-

PRSI option: 0

PLL: ON

16MHz≤fxx≤32MHz 0.75⋅fxx+3.0 1.04*fxx+5.4 mA

PLL: OFF

4MHz≤fxx≤16MHz 0.70⋅fxx+1.9 1.00*fxx+4.0 mA

Peripheral: fxx/2

PRSI option: 1

PLL: ON

16MHz≤fxx≤32MHz 0.56⋅fxx+2.8 0.69*fxx+7.0 mA

All peripherals

stopped

Peripheral: fxx

PRSI option: 0

PLL: ON

16MHz≤fxx≤32MHz 0.46⋅fxx+2.8 mA

PLL: OFF

4MHz≤fxx≤16MHz 0.44⋅fxx+1.6 mA

Peripheral: fxx/2

PRSI option: 1

PLL: ON

16MHz≤fxx≤32MHz 0.46⋅fxx+1.8 mA

IDLE1

mode IDD3

Peripheral (TAA, UARTD) run-

ning

PLL: OFF

4MHz≤fxx≤16MHz

Note7

0.151⋅fxx+0.90 0.209⋅fxx+ 1.93 mA

All peripherals stopped 0.035⋅fxx+1.01 mA

IDLE2

mode IDD4 PLL: OFF

4MHz ≤fxx≤16MHz Note7 0.037⋅fxx+0.21 0.049⋅fxx+ 0.88 mA

Data Sheet U18567EE1V3DS00

V850ES/FJ3

4.6.3.3 µPD70F3381, µPD70F3382

(a) Absolute values

(Ta = -40 to +125°C, C=4.7uF,

VDD = EVDD = BVDD = 3.3 to 5.5V, AVREF0 = 3.3 to 5.5V, VSS = EVSS = BVSS = AVSS = 0VNote1)

Mode Symbol Condition TYP. MAX. Unit

Operating

mode

Note2,8

IDD1

All peripherals

running

Peripheral: fxx

PRSI option: 0

PLL: ON

12MHz≤fxx≤32MHz

fxx=20MHz

fx=5MHz 30 41 mA

fxx=32MHz

fx=16MHz 43 57 mA

PLL: OFF

4MHz≤fxx≤16MHz

fxx=8MHz

8MHz Internal-

OSC Note3

15 22 mA

fxx=16MHz

fx=16MHz 24 32 mA

All peripherals

stopped

Peripheral: fxx

PRSI option: 0

PLL: ON

12MHz≤fxx≤32MHz

fxx=20MHz

fx=5MHz 23 mA

fxx=32MHz

fx=16MHz 33 mA

PLL: OFF

4MHz≤fxx≤16MHz

fxx=8MHz

8MHz Internal-

OSC Note3

13 mA

fxx=16MHz

fx=16MHz 19 mA

HALT

mode

Note8

IDD2

All peripherals

running

Peripheral: fxx

PRSI option: 0

PLL: ON

12MHz≤fxx≤32MHz

fxx=20MHz

fx=5MHz 19 28 mA

fxx=32MHz

fx=16MHz 28 40 mA

PLL: OFF

4MHz≤fxx≤16MHz

fxx=8MHz

8MHz Internal-

OSC Note3

914mA

fxx=16MHz

fx=16MHz 15 22 mA

All peripherals

stopped

Peripheral: fxx

PRSI option: 0

PLL: ON

12MHz≤fxx≤32MHz

fxx=20MHz

fx=5MHz 13 mA

fxx=32MHz

fx=16MHz 18 mA

PLL: OFF

4MHz≤fxx≤16MHz

fxx=8MHz

8MHz Internal-

OSC Note3

6mA

fxx=16MHz

fx=16MHz 10 mA

70 Data Sheet U18567EE1V3DS00

V850ES/FJ3

IDLE1

mode IDD3

Peripheral (TAA, UARTD) run-

ning

PLL: OFF

4MHz≤fxx≤16MHz

Note7

fxx=5MHz

fx=5MHz 2.6 3.9 mA

fxx=12MHz

fx=12MHz 4.1 5.9 mA

fxx=16MHz

fx=16MHz 4.9 7.1 mA

fxx=8MHz, 8MHz Internal-OSCNote3 3.0 4.5 mA

All peripherals stopped

PLL: OFF

4MHz≤fxx≤16MHz

Note7

fxx=5MHz

fx=5MHz 1.4 mA

fxx=12MHz

fx=12MHz 1.8 mA

fxx=16MHz

fx=16MHz 2.0 mA

fxx=8MHz, 8MHz Internal-OSCNote3 1.3 mA

IDLE2

mode IDD4

PLL: OFF

4MHz≤fxx≤16MHz

Note7

fxx=5MHz

fx=5MHz 0.4 1.1 mA

fxx=12MHz

fx=12MHz 0.7 1.5 mA

fxx=16MHz

fx=16MHz 0.8 1.7 mA

fxx=8MHz, 8MHz Internal-OSC Note3 0.2 1.0 mA

SUB

operating

modeNote5

IDD5

RC resonator (fxt=20kHz) Note6 90 850 µA

240 kHz Internal-OSC (SubOSC stopped) 330 1760 µA

SubIDLE

mode

Note3,5

IDD6

RC resonator (fxt=20kHz) Note6 40 670 μA

240kHz Internal-OSC (SubOSC stopped) 25 630 μA

STOP

mode

Note3,4

IDD7

POC stop 240kHz Internal-OSC stop 7.5 550 μA

240kHz Internal-OSC working 15.5 565 μA

POC work 240kHz Internal-OSC stop 10.5 555 μA

240kHz Internal-OSC working 18.5 570 μA

Mode Symbol Condition TYP. MAX. Unit

Data Sheet U18567EE1V3DS00

V850ES/FJ3

(b) Calculation formulas

(Ta = -40 to +125°C, C=4.7uF,

VDD = EVDD = BVDD = 3.3 to 5.5V, AVREF0 = 3.3 to 5.5V, VSS = EVSS = BVSS = AVSS = 0VNote1)

Notes: 1. VDD, EVDD and BVDD total current. (Ports are stopped).

AVREF0 current, port buffer current (including a current flowing in the on-chip pull-up/pull-

down resistor) are not included.

2. The code flash and the data flash are in read mode.

When the device is in programming mode (Self-programming mode or data flash program-

ming mode), the current value (MAX. value) adds by the following value:

•Self-programming mode:

+ In case of PLL OFF: 7-(0.33*fxx+0.1) [mA]

+ In case of PLL ON: 7-(0.18*fxx+3.0) [mA]

•Data flash programming mode:

+ 7-(0.18*fxx/4+3.0) [mA]

3. Main OSC is stopped.

4. Do not use SubOSC.

5. POC is working. 240kHz Internal-OSC is working. 8MHz Internal-OSC is stopped.

6. RC Oscillation frequency is typ.40kHz. This clock is divided by 2 internally.

7. 8MHz Internal-OSC is stopped

8. When the SSCG is running, the current value adds typ +2.5mA, max +4mA.

The formulas are for reference only. Not all possible values for fxx are tested in the outgoing device

inspection.

Mode Symbol Condition TYP. Note9 MAX. Note3 Unit

Operating

mode

Note2,8

IDD1

All peripherals

running

Peripheral: fxx

PRSI option: 0

PLL: ON

12MHz≤fxx≤32MHz 1.06⋅fxx+7.1 1.27⋅fxx+13.6 mA

PLL: OFF

4MHz≤fxx≤16MHz 1.06⋅fxx+5.5 1.28⋅fxx+10.6 mA

Peripheral: fxx/2

PRSI option: 1

PLL: ON

12MHz≤fxx≤32MHz 0.94⋅fxx+6.0 1.13⋅fxx+12.2 mA

All peripherals

stopped

Peripheral: ffxx-

PRSI option: 0

PLL: ON

12MHz≤fxx≤32MHz 0.81⋅fxx+6.2 mA

PLL: OFF

4MHz≤fxx≤16MHz 0.83⋅fxx+5.7 mA

Peripheral: fxx/2

PRSI option: 1

PLL: ON

12MHz≤fxx≤32MHz 0.79⋅fxx+6.2 mA

HALT

mode

Note8

IDD2

All peripherals

running

Peripheral: ffxx-

PRSI option: 0

PLL: ON

16MHz≤fxx≤32MHz 0.75⋅fxx+3.0 1.04*fxx+5.4 mA

PLL: OFF

4MHz≤fxx≤16MHz 0.70⋅fxx+1.9 1.00*fxx+4.0 mA

Peripheral: fxx/2

PRSI option: 1

PLL: ON

16MHz≤fxx≤32MHz 0.56⋅fxx+2.8 0.69*fxx+7.0 mA

All peripherals

stopped

Peripheral: fxx

PRSI option: 0

PLL: ON

16MHz≤fxx≤32MHz 0.46⋅fxx+2.8 mA

PLL: OFF

4MHz≤fxx≤16MHz 0.44⋅fxx+1.6 mA

Peripheral: fxx/2

PRSI option: 1

PLL: ON

16MHz≤fxx≤32MHz 0.46⋅fxx+1.8 mA

IDLE1

mode IDD3

Peripheral (TAA, UARTD) run-

ning

PLL: OFF

4MHz≤fxx≤16MHz

Note7

0.151⋅fxx+0.90 0.209⋅fxx+ 1.93 mA

All peripherals stopped 0.035⋅fxx+1.01 mA

IDLE2

mode IDD4 PLL: OFF

4MHz ≤fxx≤16MHz Note7 0.037⋅fxx+0.21 0.049⋅fxx+ 0.88 mA

72 Data Sheet U18567EE1V3DS00

V850ES/FJ3

4.7 AC Characteristics

AC test Input measurement points ( VDD, AVREF0, EVDD, BVDD)

AC test output measurement points

Load conditions

Caution: If the load capacitance exceeds 50pF due to the circuit configuration, reduce the load

capacitance of the device to 50pF or less by inserting a buffer or by some other means.

measure point

VIH(min)

VIL(max)

VIH(min)

VIL(max)

VDD

VSS

measure point

VOH(min)

VOL(max)

VOH(min)

VOL(max)

CL = 50 pF

DUT

( Device under

test )

Data Sheet U18567EE1V3DS00

V850ES/FJ3

4.7.1 CLKOUT Output Timing

Specification is identical to that from (A)-Grade except Ta=-40 to +125°C.

4.7.2 Bus Timing (Multiplexed bus mode)

Specification is identical to that from (A)-Grade except Ta=-40 to +125°C.

4.7.3 RESET, Interrupt, ADTRG Timing

Specification is identical to that from (A)-Grade except Ta=-40 to +125°C.

4.7.4 Key Return Timing

Specification is identical to that from (A)-Grade except Ta=-40 to +125°C.

4.7.5 Timer Timing

Specification is identical to that from (A)-Grade except Ta=-40 to +125°C.

4.7.6 CSI Timing

Specification is identical to that from (A)-Grade except Ta=-40 to +125°C.

4.7.7 UART Timing

Specification is identical to that from (A)-Grade except Ta=-40 to +125°C.

4.7.8 IIC Timing

Specification is identical to that from (A)-Grade except Ta=-40 to +125°C.

4.7.9 CAN Timing

Specification is identical to that from (A)-Grade except Ta=-40 to +125°C.

74 Data Sheet U18567EE1V3DS00

V850ES/FJ3

4.8 A/D Converter

(Ta = -40 to +125°C, C=4.7uF, VDD = EVDD = BVDD = 3.5 to 5.5V, AVREF0 = 4.0 to 5.5V, VSS = EVSS = BVSS = AVSS = 0V)

Notes: 1. Overall error excluding quantization error (±0.05%FSE). It is indicated as a ratio to the full-

scale value.

2. Excluding quantization error (±1/2 LSB)

3. Not tested in production.

4. Does not include input/output capacitance CIO

4.9 POC

Specification is identical to that from (A)-Grade except Ta=-40 to +125°C.

4.10 LVI

Specification is identical to that from (A)-Grade except Ta=-40 to +125°C.

4.11 RAM Retention Flag

Specification is identical to that from (A)-Grade except Ta=-40 to +125°C.

4.12 Data Retention Characteristics

Specification is identical to that from (A)-Grade except Ta=-40 to +125°C.

Parameter Symbol Conditions MIN. TYP. MAX. Unit

Resolution 10 bit

Overall errorNote1 4.0V≤AVREF0<5.5V ±0.15 ±0.35 %FSR

Conversion time tCONV 3.10 16 μs

Stabilization time tSTA After ADA0PS bit = 0 -> 1 2 μs

Recovery time for power down

mode tDPU 1 µs

Zero-scale errorNote1 ZSE ±0.35 %FSR

Full-scale errorNote1 FSE ±0.35 %FSR

Integral non-liniearity errorNote2 INL ±2.5 LSB

Differential non-liniearity errorNote2 DNL ±1.5 LSB

Analog input voltage VIAN AVSS AVREF0 V

Analog input equivalent

circuit capacitance Note3,4 CINA 6.19 pF

Analog input equivalent

circuit resistance Note3 RINA 2.55 kΩ

AVREF0 current IAREF0 A/D operating 4 7 mA

A/D operation stop 1 10 uA

Conversion rusult when using

Diagnostic function

AVREF0 conversion 3FC 3FF HEX

AVSS conversion 000 003 HEX

Data Sheet U18567EE1V3DS00

V850ES/FJ3

4.13 Flash Memory Programming Characteristics

(a) Basic Characteristics

(C=4.7uF, VDD = EVDD = BVDD, AVREF0 = 3.5 to 5.5V, VSS = EVSS = BVSS = AVSS = 0V)

Notes: 1. Under the condition of CWRT1

2. Under the condition of CWRT2

Remark: The initial write when the product is shipped, any erase → write set of operations, or any

programming operation is counted as one rewrite.

Example: P: Program(write) E: Erase

Product is shipped → P → E → P → E → P : Rewrite count: 3

Product is shipped → E → P → E → P → E → P : Rewrite count: 3

(b) Serial Writing Operation Characteristics

Specification is identical to that from (A)-Grade except Ta=-40 to +125°C.

Parameter Symbol Conditions MIN. TYP. MAX. Unit

Operation frequency fCPU ≤256KB product 4 24 MHz

≥384KB product 4 32

Supply voltage VDD 3.3 5.5 V

Number of rewrites CWRT1 Code Flash 1000 count

Data Flash

CWRT2 10000

High level input voltage VIH FLMD0 0.8EVDD EVDD V

Low level input voltage VIL FLMD0 EVSS 0.2EVDD V

Programming temperature tPRG -40 +125 °C

Data retention

Code Flash 15Note1

year

Data Flash 5Note2

76 Data Sheet U18567EE1V3DS00

V850ES/FJ3

Data Sheet U18567EE1V3DS00

V850ES/FJ3

5. Package

5.1 Package Dimension

Sxb

0.125 +0.075

−0.035

(UNIT:mm)

ITEM DIMENSIONS

20.00 ±0.20

22.00 ±0.20

1.60 MAX.

0.10 ±0.05

1.40 ±0.05

0.25

0.50

0.08

1.25

0.50

0.60 ±0.15

1.00 ±0.20

P144GJ-50-GAE

3°+5°

−3°

NOTE

Each lead centerline is located within 0.08mm of

its true position at maximum material condition.

detail of lead end

144-PIN PLASTIC LQFP (FINE PITCH) (20x20)

0.20

144 37

108

109

+0.07

−0.03

78 Data Sheet U18567EE1V3DS00

V850ES/FJ3

5.2 Product Marking

5.2.1 Marking of pin 1 at a QFP (Quad Flat Package)

Example 1: The index mark for pin 1 is the beveled edge of the package

Example 2: The index mark for pin 1 is a round notch at one of the 4 edges. In this case, the shape of

all edges is identical (usually beveled).

Example 3: For production reasons, two or more similar notches may be located at the top of the pack-

age. In such a case the index marker for pin 1 is a round notch with an additional mark in it.

Note: RoHS compliant devices have an additional dot at the top side. Do not mix it up with the mark-

ing for pin 1. For details see 5.2.2 "Identification of Lead-Free Products" on page 79.

Data Sheet U18567EE1V3DS00

V850ES/FJ3

5.2.2 Identification of Lead-Free Products

Lead-Free products are marked with a dot "•". The marking methods are the paint or the laser (It

doesn't sink in). The shape of lead-free marks is a circle.

Example:

80 Data Sheet U18567EE1V3DS00

V850ES/FJ3

Data Sheet U18567EE1V3DS00

V850ES/FJ3

6. Change History

The following revision list shows all major changes of the different datasheet versions.

Version Chapter Comment

V1.0 Initial release

V1.1

2.13

3.13

Removed ’Target Specification’ for (A)- and (A1)-Grade Devices in the Flash Pro-

gramming specifications.

Changed specification of ’Number of rewrites’ from MAX. to MIN.

2.8

4.8 Removed Caution (Described in User’s Manual)

V1.2 Corrected device name in page header.

V1.3

Changed document status from ’Preliminary Datasheet’ to ’Datasheet’.

4.13 Removed ’Target Specification’ for (A2)-Grade Devices in the Flash Programming

specifications.

82 Data Sheet U18567EE1V3DS00

V850ES/FJ3

Although NEC has taken all possible steps

to ensure that the documentation supplied

to our customers is complete, bug free

and up-to-date, we readily accept that

errors may occur. Despite all the care and

precautions we've taken, you may

encounter problems in the documentation.

Please complete this form whenever

you'd like to report errors or suggest

improvements to us.

Hong Kong, Philippines, Oceania

NEC Electronics Hong Kong Ltd.

Fax: +852-2886-9022/9044

Korea

NEC Electronics Hong Kong Ltd.

Seoul Branch

Fax: 02-528-4411

Taiwan

NEC Electronics Taiwan Ltd.

Fax: 02-2719-5951

Address

North America

NEC Electronics America Inc.

Corporate Communications Dept.

Fax: 1-800-729-9288

1-408-588-6130

Europe

NEC Electronics (Europe) GmbH

Market Communication Dept.

Fax: +49(0)-211-6503-1344

Asian Nations except Philippines

NEC Electronics Singapore Pte. Ltd.

Fax: +65-6250-3583

Japan

NEC Semiconductor Technical Hotline

I would like to report the following error/make the following suggestion:

Document title:

Document number: Page number:

Thank you for your kind support.

If possible, please fax the referenced page or drawing.

Excellent Good Acceptable PoorDocument Rating

Clarity

Technical Accuracy

Organization

CS 99.1

Name

Company

From:

Tel. FAX

Facsimile

Message

Fax: +81- 44-435-9608

[MEMO]