PTH12050 12 Vin single output DC-DC CONVERTERS POLA Non-isolated 1 NEW Product * 6 A output current * 12 V input voltage * Wide-output voltage adjust * 1.2 Vdc to 5.5 Vdc for suffix `W' and 0.8 Vdc to 1.8 Vdc for suffix `L' * Auto-trackTM sequencing* * Pre-bias start-up * Efficiencies up to 93% * Output ON/OFF inhibit * Output voltage sense * Point-of-Load-Alliance (POLA) compatible * Available RoHS compliant The PTH12050 is a next generation series of non-isolated dc-dc converters offering some of the most advanced POL features available in the industry. The primary new feature provides for sequencing between multiple modules, a function, which is becoming a necessity for powering advanced silicon including DSP's, FPGA's and ASIC's requiring controlled power-up and power-down Other industry leading features include efficiencies up to 93%. The PTH12050 has an input voltage of 10.8 Vdc to 13.2 Vdc and offers a wide output voltage range adjustable with external trim resistor, allowing for maximum design flexibility and a pathway for future upgrades. 2 YEAR WARRANTY All specifications are typical at nominal input, full load at 25 C unless otherwise stated Cin = 100 F, Cout = 0 F OUTPUT SPECIFICATIONS Voltage adjustability (See Note 4) SPECIFICATIONS EMC CHARACTERISTICS Suffix `W' Suffix `L' 1.2-5.5 Vdc 0.8-1.8 Vdc Setpoint accuracy 2.0% Vo Electrostatic discharge Conducted immunity Radiated immunity EN61000-4-2, IEC801-2 EN61000-4-6 EN61000-4-3 Line regulation 5 mV typ. GENERAL SPECIFICATIONS Load regulation 5 mV typ. Efficiency Total regulation 3.0% Vo 0A Minimum load Ripple and noise 20 MHz bandwidth Suffix `W' Suffix `L' Vo Vo Vo Vo 2.5 V > 2.5 V 1.0 V > 1.0 V Temperature co-efficient -40 C to +85 C 25 mV pk-pk 1% Vo 20 mV pk-pk 30 mV pk-pk 0.5% Vo Transient response (See Note 5) 70 s recovery time Overshoot/undershoot 100 mV Margin adjustment 5.0% Vo INPUT SPECIFICATIONS Input voltage range (See Note 3) Input current No load Remote ON/OFF (See Note 1) Insulation voltage Switching frequency Over Vin and Io ranges Non-isolated Suffix `W' Suffix `L' 320 kHz typ. 250 kHz typ. Approvals and standards EN60950 UL/cUL60950 UL94V-0 Material flammability Dimensions (L x W x H) 22.10 x 12.57 x 8.50 mm 0.870 x 0.495 x 0.335 in 2.9 g (0.10 oz) Weight MTBF Telcordia SR-332 7,092,000 hours ENVIRONMENTAL SPECIFICATIONS 10.8-13.2 Vdc 10 mA typ. Positive logic Thermal performance (See Note 2) MSL (`Z' suffix only) Operating ambient, temperature Non-operating -40 C to +85 C -40 C to +125 C JEDEC J-STD-020C Level 3 1 V/ms Start-up time 8.8-0.4 V typ. Undervoltage lockout Track input voltage See Tables on Page 2 Pin 8 (See Note 6) 0.3 Vin International Safety Standard Approvals PROTECTION Short-circuit Auto reset 14 A typ. *Auto-trackTM is a trade mark of Texas Instruments UL/cUL CAN/CSA-C22.2 No. 60950-1-03/UL 60950-1, File No. E174104 TUV Product Service (EN60950) Certificate No. B 04 06 38572 044 CB Report and Certificate to IEC60950, Certificate No. US/8292/UL File Name: pth12050.pdf Rev: 6 Nov 2006 PTH12050 12 Vin single output DC-DC CONVERTERS POLA Non-isolated2 2 For the most current data and application support visit www.artesyn.com/powergroup/products.htm OUTPUT POWER (MAX.) INPUT VOLTAGE 33 W 10.8-13.2 Vdc 33 W 10.8-13.2 Vdc OUTPUT VOLTAGE 0.8-1.8 Vdc 1.2-5.5 Vdc Part Number System with Options NEW Product OUTPUT CURRENT (MIN.) OUTPUT CURRENT (MAX.) EFFICIENCY (MAX.) LINE LOAD MODEL NUMBER (9,10) 0A 6A 88% 5 mV 5 mV PTH12050L 0A 6A 93% 5 mV 5 mV PTH12050W REGULATION PTH12050WAST Product Family Point of Load Alliance Compatible Input Voltage 12 = 12 V Output Current 05 = 6 A Mechanical Package Always 0 Packaging Options No Suffix = Trays T = Tape and Reel (7) Mounting Option (9) D = Horizontal Through-Hole (Matte Sn) H = Horizontal Through-Hole (Sn/Pb) S = Surface-Mount (63/37 Sn/Pb pin solder material) Z = Surface-Mount (96.5/3.0/0.5 Sn/Ag/Cu pin solder material) Pin Option A = Through-Hole Std. Pin Length (0.140") A = Surface-Mount Tin/Lead Solder Ball Output Voltage Adjustment of the PTH12050 Series The ultra-wide output voltage trim range offers major advantages to users who select the PTH12050. It is no longer necessary to purchase a variety of modules in order to cover different output voltages. The output voltage can be trimmed in a range of 1.2 V to 5.5 V for suffix `-W' and 0.8 V to 1.8 V for suffix `-L'. When the PTH12050 converter leaves the factory the output has been adjusted to the default voltage of 1.2 V for the PTH12050W and 0.8V for the PTH12050L. Notes 1 Remote ON/OFF. Positive Logic Pin 3 open; or V > Vin - 0.5 V ON: OFF: Pin 3 GND; or V < 0.8 V (min - 0.2 V). 2 See Figure 1 for safe operating curve. 3 A 100 F electrolytic input capacitor is required for proper operation. The capacitor must be rated for a minimum of 750 mA rms of ripple current. C2 = 10 F ceramic capacitor, required for output voltages of 3.3 V and higher. 4 An external output capacitor is not required for basic operation. Adding 100 F of distributed capacitance at the load will improve the transient response. 5 1 A/s load step, 50 to 100% Iomax, Cout = 100 F. 6 If utilized Vout will track applied voltage by 0.3 V (up to Vo set point). 7 Tape and reel packaging only available on the surface-mount versions. 8 The pk-pk output ripple voltage is measured with an external 10F ceramic capacitor. See Figure 3 Standard application schematic. 9 To order Pb-free (RoHS compatible) surface-mount parts replace the mounting option `S' with `Z', e.g. PTH12050WAZ. To order Pb-free (RoHS compatible) through-hole parts replace the mounting option `H' with `D', e.g. PTH12050WAD. 10 NOTICE: Some models do not support all options. Please contact your local Artesyn representative or use the on-line model number search tool at http://www.artesyn.com/powergroup/products.htm to find a suitable alternative. Output Voltage Code W = Wide. L = Low Voltage EFFICIENCY TABLE - PTH12050W (IO = 5 A) OUTPUT VOLTAGE EFFICIENCY Vo = 5.0 V 93% Vo = 3.3 V 91% Vo = 2.5 V 89% Vo = 2.0 V 88% Vo = 1.8 V 87% Vo = 1.5 V 86% Vo = 1.2 V 84% EFFICIENCY TABLE - PTH12050L (IO = 5 A) OUTPUT VOLTAGE EFFICIENCY Vo = 1.8 V 88% Vo = 1.5 V 87% Vo = 1.2 V 85% Vo = 1.0 V 83% Vo = 0.8 V 81% File Name: pth12050.pdf Rev: 6 Nov 2006 PTH12050 12 Vin single output DC-DC CONVERTERS POLA Non-isolated 3 For the most current data and application support visit www.artesyn.com/powergroup/products.htm NEW Product PTH12050W Characteristic Data 90 100 95 90 70 60 Nat Conv 100 LFM 50 200 LFM 400 LFM 40 30 EFFICIENCY (%) TEMPERATURE (C) 80 80 75 1 2 3 4 5 2.0V 1.8V 1.5V 1.2V 70 65 60 20 0 Vout 5.0V 3.3V 2.5V 85 0 6 1 OUTPUT CURRENT (A) 2 3 4 5 6 OUTPUT CURRENT (A) Figure 2 - Efficiency vs Load Current for PTH12050W Vin = 12 V (See Note B) Figure 1 - Safe Operating Area for PTH12050W Vin = 12 V, Output Voltage = 3.3 V (See Note A) PTH12050L Characteristic Data 100 80 90 70 60 Nat Conv 100 LFM 50 40 30 20 0 1 2 3 4 5 EFFICIENCY (%) TEMPERATURE (C) 90 Vout 1.8V 1.5V 1.2V 1.0V 0.8V 80 70 60 50 6 0 OUTPUT CURRENT (A) 1 2 3 4 5 6 OUTPUT CURRENT (A) Figure 4 - Efficiency vs Load Current for PTH12050L Vin = 12 V (See Note B) Figure 3 - Safe Operating Area for PTH12050L Vin = 12 V, Output Voltage 1.8 V (See Note A) Notes Auto-track 1 Vout 6 A SOA curves represent the conditions at which internal components are within the Artesyn derating guidelines. B Characteristic data has been developed from actual products tested at 25 C. This data is considered typical data for the converter. 2 Vin 3 4 PTH12050 (Top View) 5 Cin 100F (Required) + Inhibit + Cout 100F (Optional) RSET 0.5%, 0.1W (Required) GND GND Figure 5 - Standard Application - All Models File Name: pth12050.pdf Rev: 6 Nov 2006 PTH12050 12 Vin single output DC-DC CONVERTERS POLA Non-isolated 4 For the most current data and application support visit www.artesyn.com/powergroup/products.htm NEW Product 0.140 (3.55) 0.870 (22.10) 0.060 (1.52) 0.060 (1.52) 0.750 (19.06) 6 1 0.125 (3.18) 0.125 (3.18) 0.125 (3.18) 0.040 (1.02) 6 Places 2 0.375 0.495 (12.57) (9.52) Lowest Component 0.010 min. (0.25) Bottom side Clearance 3 PIN CONNECTIONS 5 4 0.070 (1.78) (Standoff Shoulder) TOP VIEW Host Board 0.335 (8.50) MAX. SIDE VIEW Dimensions in Inches (mm) Tolerances (unless otherwise specified) 2 Places 0.030 (0.76) 3 Places 0.010 (0.25) Figure 6 - Plated Through-Hole Mechanical Drawing PIN NO. FUNCTION 1 Ground 2 Track 3 Vin 4 Inhibit* 5 Vo adjust 6 Vout *Denotes negative logic: Open = Normal operation Ground = Function active 0.870 (22.10) 0.060 (1.52) 0.125 (3.18) 0.125 (3.18) 0.125 (3.18) 0.060 (1.52) 0.750 (19.06) 0.335 (8.50) max.* *After solder reflow on customer board 6 1 2 Solder Ball 0.040 (1.02) 6 Places 0.495 0.375 (12.57) (9.52) 3 5 4 TOP VIEW SIDE VIEW Dimensions in Inches (mm) Tolerances (unless otherwise specified) 2 Places 0.030 (0.76) 3 Places 0.010 (0.25) Figure 7 - Surface-Mount Mechanical Drawing Datasheet (c) Artesyn Technologies(R) 2006 The information and specifications contained in this datasheet are believed to be correct at time of publication. However, Artesyn Technologies accepts no responsibility for consequences arising from printing errors or inaccuracies. The information and specifications contained or described herein are subject to change in any manner at any time without notice. No rights under any patent accompany the sale of any such product(s) or information contained herein. Please consult our website for the following items: 4 Application Note www.artesyn.com File Name: pth12050.pdf Rev: 6 Nov 2006