MC33232 Power Factor Controller The MC33232 is the monolithic Integrated Circuit using the SMARTMOS(R) process as the new technology. And is active power factor controller specially design for use as off-line power converter application. This integrated circuit features an internal startup timer for stand-alone application, a one quadrant multiplier for near unity power factor, zero current detector to ensure critical condition operation, transconductance error amplifier, quickstart circuit for enhanced startup, trimmed internal bandgap reference, current sensing comparator, a totem pole output ideally suited for drive a power MOSFET, and a one shot-rigger circuit to eliminate a problem at the light loading. Also included are protective features consisting of an overvoltage comparator to eliminate runaway output voltage due to removal, and a protect circuit to eliminate thermal runaway. This device is available in dual-in-line and surface mount plastic package. http://onsemi.com SILICON MONOLITHIC INTEGRATED CIRCUIT MARKING DIAGRAMS PDIP-8 P SUFFIX CASE 626 Features * * * * * * * * * * * One Shot-trigger Circuit to Eliminate a Problem at the Light Loading Overvoltage Comparator Eliminates Runaway Output Voltage Quickstart Circuit for Enhanced Startup Internal Startup Timer One Quadrant Multiplier Zero Current Detector Trimmed 2% Internal Bandgap Reference Totem Pole Output with High State Clamp Undervoltage Lockout with 6.0 V of Hysteresis Low Startup and Operating Current These are Pb-Free Devices MC33232P AWL YYWWG 8 SOIC-8 D SUFFIX CASE 751 1 A WL or L Y WW or W G or G 33232 ALYW G = Assembly Location = Wafer Lot = Year = Work Week = Pb-Free Package PIN ASSIGNMENT Voltage Feedback Input 1 8 VCC Compensation 2 7 Drive Output Multiplier Input Current Sense Input 3 6 4 5 GND Zero Current Detect Input ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 2 of this data sheet. (c) Semiconductor Components Industries, LLC, 2009 July, 2009 - Rev. 3 1 Publication Order Number: MC33232/D MC33232 1.4 V 28 V 8 5.3 V 5 + Zero Current Detector 1.6 V/1.4 V 2.5 V Reference + POR UVLO Timer 16 V 7 TSD + One-shot 5 k Current Sensor 4 2p + Over Voltage Comparator Vref + 1.5 V 1.067 Vref Multiplier Err Amp 3 1 Quickstart 2 6 Figure 1. Simplified Block Diagram ORDERING INFORMATION Device Operating Junction Temperature Range MC33232PG MC33232DG -40C to +150C MC33232DR2G Package Shipping PDIP-8 (Pb-Free) 50 Units / Rail SOIC-8 (Pb-Free) 98 Units / Rail SOIC-8 (Pb-Free) 2500 Tape & Reel For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. http://onsemi.com 2 MC33232 IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIII IIIII IIIIIIIIII III IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIII IIIII IIIIIIIIII III IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIII IIIII IIIIIIIIII III IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIII IIIII IIIIIIIIII III IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIII IIIII IIIIIIIIII III IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII MAXIMUM RATINGS Parameter Total Power Supply and Zener Current Symbol Value Unit (ICC + IZ) 30 mA Output Current, Source or Sink (Note 1) Peak Current (Under 0.5 msec) DC (Continuously Current) IO Current Sense, Multiplier and Voltage Feedback Input Vin Zero Current Detect Input High State Forward Current Low State Reverse Current Iin Power Dissipation and Thermal Characteristic D Suffix, Plastic Package, Case 751 Maximum Power Dissipation @ TA = 70C Thermal Resistance, Junction-to-Air P Suffix, Plastic Package, Case 626 Maximum Power Dissipation @ TA = 70C Thermal Resistance, Junction-to-Air mA 750 300 -0.3 to 10 V mA 50 -10 PD RqJA 450 178 mW C/W PD RqJA 800 100 mW C/W Operating Junction Temperature TJ +150 C Storage Temperature Tstg -55 to +150 C Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. 1. Maximum package power dissipation limits must be observed. RECOMMENDED OPERATING CONDITION (VCC = 12 V and TA = 25C unless otherwise noted) AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAA AAAAA AAAA AAAA AAAA AAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA Characteristic Symbol Min Typ Max F Operating Frequency (RZCD = 4.7 kW, Cerr = 0.68 mF) MHz Normal Loading 0.4 Under Loading 1.0 External Resistance for Zero Current Detect Control Operating Ambient Temperature Unit RZCD - 4.7 - kW TA -20 - +85 C Max Unit ELECTRICAL CHARACTERISTICS (VCC = 12 V, for typical values TA = -20C ~ +85C, unless otherwise noted) Characteristic Symbol Min Typ AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA ERROR AMPLIFIER Voltage Feedback Input Threshold VFB V TA = 25C 2.465 2.5 2.535 TA = -20C ~ +85C (VCC = 12 V ~ 25 V) 2.44 - 2.54 Line Regulation (VCC = 12 V ~ 25 V, TA = 25C) Regline - 1.0 10 mV Input Bias Current (VFB = 0 V) IIB - -0.1 -0.5 mA Transconductance (TA = 25C) gm 80 100 130 mmho Output Current (VCC = 12 V ~ 28 V, TA = 25C) mA Source (VFB = 2.3 V) Isource - 10 - Sink (VFB = 2.7 V) Isink - 10 - High State (VFB = 2.3 V) VOH(ea) 5.8 6.2 - Low State (VFB = 2.7 V) VOL(ea) - 1.7 2.4 Output Voltage Swing V OVERVOLTAGE COMPARATOR AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA Voltage Feedback Input Threshold VTH 1.04 VFB 1.067 VFB 1.095 VFB V - - C OVERTEMPERATURE PROTECT CIRCUIT (This item is just reference value without any specifying) Detect Temperature TSD http://onsemi.com 3 120 MC33232 ELECTRICAL CHARACTERISTICS (VCC = 12 V, for typical values TA = -20C ~ +85C, unless otherwise noted) AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAA AAAAA AAAA AAAA AAAA AAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAA AAAAA AAAA AAAA AAAA AAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAA AAAAA AAAA AAAA AAAA AAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAA AAAAA AAAA AAAA AAAA AAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA Characteristic Symbol Min Typ Max Unit Vthm 1.05 VOL 1.2 VOL - V (ea) (ea) MULTIPLIER Input Threshold (Pin 2) Dynamic Input Voltage Range V Multiplier Input (Pin 3) Vpin 3 0 to 2.5 0 to 3.5 - Compensation (Pin 2) Vpin 2 Vthm to Vthm + 1.0 Vthm to Vthm + 1.5 - Input Bias Current, Pin 3 (VFB = 0 V) IIB(mult) - -0.1 -0.5 mA Multiplier Gain (Vpin 3 = 0.5 V, Vpin 2 = VFB + 1.0 V) K 0.43 0.65 0.87 1/V Input Threshold Voltage (Vin Increasing) Vth(ZCD) 1.33 1.6 1.87 V Hysteresis (Vin Decreasing) VH(ZCD) 100 200 300 mV High State (IDET = +3.0 mA) VIH 5.0 5.3 - V Low State (IDET = -3.0 mA) VIL 0.3 0.7 1.0 ZERO CURRENT DETECTOR Input Clamp Voltage Propagation Delay Time Zero Current Detect to Drive Out nsec RZCD = 4.7 kW TZO - 100 200 TOS 500 - 850 ONE SHOT TRIGGER Output Minimum Off Time nsec CURRENT SENSE COMPARATOR Input Bias Current (Vpin 4 = 0 V) IIB(cs) - -0.15 -1.0 mA Input Offset Voltage (Vpin 2 = 1.1 V, Vpin 3 = 0 V) Vio(cs) - 9.0 25 mV Vthmax 1.3 1.5 1.8 V tPHL(in/out) - 100 200 nsec VOL - - 0.3 2.4 0.8 3.3 VOH 9.8 7.8 10.3 8.4 - - V VO 14 16 18 V Output Voltage Rise Time (CL = 1.0 nF) tr - 50 120 nsec Output Voltage Fall Time tf - 50 120 nsec VO(UVLO) - 0.1 0.5 V Restart Time Delay tDLY 200 900 - msec Restart Time at Startup POR 0 25 - msec Startup Threshold (VCC Increasing) Vth(on) 14.4 16 17.6 V Minimum Operating Voltage After Turn-off (VCC Decreasing) Vshut 9.0 10 11 V Maximum Current Sense Input Threshold AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAA AAAAA AAAA AAAA AAAA AAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA Delay to Output DRIVE OUTPUT Output Voltage (VCC = 12 V) Low State (Isink = 20 mA) (Isink = 200 mA) High State V (Isource = 20 mA) (Isource = 200 mA) Output Voltage (VCC = 25 V, Isource = 20 mA, CL = 15 pF) (CL = 1.0 nF) AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA Output Voltage with UVLO Active (VCC = 7.0 V, Isink = 1.0 mA) RESTART TIMER UNDER VOLTAGE LOCKOUT (Metal Option Version) AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAA AAAAA AAAA AAAA AAAA AAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA Hysteresis VH 3.5 6.0 8.6 V ICC - - - 0.05 6.5 9.0 0.1 12 20 mA VZ 26 28 - V TOTAL DEVICE Power Supply Current Startup (VCC = 7.0 V) Operating Dynamic Operating (50 KHz, CL = 1.0 nF) Power Supply Zener Voltage (ICC = 25 mA) http://onsemi.com 4 MC33232 AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAA AAAAAAAAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAA AAAAAAAAAAAAA AAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAA AAAAA A AAAAAAAAAAAAA AAAAAA AAAAAAA AAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAA AAAAAAAAAAAAA AAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAA AAAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAA AAAAAAA AAAAAAA AAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAA AAAAAAA AAAAAAA AAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAA AAAAA AAAAAAA AAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAA AAAAAAAAAAAAAAAAAA AAAAAAA AAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAA AAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA MEASUREMENT CONDITION Note: Test conditions follow the test circuit diagram unless otherwise noted (See last page) Item Condition VFB VFB2 Measurement Method Pin 1 = Pin 2 SW1 = B Measure Pin 1 voltage when connect Pin 1 and Pin 2 Regline IIB(err) gm Regline = VFB2 - VFB Pin 1 = 0 V Measure Pin 1 current Pin 2 = 2.0 V Pin 2 current (Ipin2) @ Pin 1 = 2.55 Pin 2 current (Ipin2) @ Pin 1 = 2.45 gm + (Ipin2 * Ipin2) (2.55 * 2.45) Isource Pin 1 = 2.3 V Isink Pin 1 = 2.7 V VOH(ea) Pin 1 = 2.3 V VOL(ea) Pin 1 = 2.7 V Vth Vin = Ref.1 Pin 4 = GND Pin 2 = 4.0 V Pin 3 = 2.0 V Measure Pin 1 voltage when Pin 7 switch to low by increasing Pin 1 voltage from 0 V Vin = Ref.1 Pin 1 = 0 V Pin 4 = 0.015 V Pin 3 = 0.5 V Measure Pin 2 voltage when Pin 7 switch to low by decreasing Pin 2 voltage from 2.5 V Vth(mult) Vpin3 SW1 = A&B Pin 2 = 2.0 V Measure Pin 2 output current Measure Pin 2 voltage Vin = Ref.1 Pin 2 = Vth(mult) a+C A Measure Pin 4 voltage when Pin 7 switch to low with each Pin 3 condition 25% @ B * a C*A 0.77 ) A 1.67 100 Vpin2 A: @ Pin 3 = 0 V B: @ Pin 3 = 1.25 V C: @ Pin 3 = 2.5 V IIB(mult) Pin 1, 3 = 0 V Pin 2 = 1.1 V Measure Pin 3 current Pin 1 = 0 V Pin 3 = 0.5 V Measure Vthp4 as Pin 4 voltage when Pin 7 switch to low by increasing Pin 4 voltage from 0 V and calculate by the following equation. Pin 2 = Vth(mult) + 1 V Vin = Ref.1 K Vth(ZCD) Measure the A, B and C with the condition and calculate the linearity of the multiplier K = Vthp4 / 0.50 Measure Pin 5 voltage when Pin 7 switch to low by increasing Vin voltage from 0 V Vin = Ref.1 Measure Vth2 as Pin 5 voltage when Pin 7 switch to low by increasing Vin voltage from 4 V and calculate VH by the following equation. VH TZO Pin 1 = 0 V SW3 = ON VH = Vth(zero) - Vth2 Measure the propagation delay time from Vin to Pin 7 Pin 2 = 3.0 V Pin 3 = 0.5 V TZO2 TBD Vin 50% TBD Pin 4 = GND SW2 = B TZO 50% Pin 7 Measure the minimum off time for Pin 7 Vin = Ref.1 2V Pin 4 TOS Pin 3 = 0.5 V delay Pin 1 = 0 V 0V 2V Vin Delay: 500 nSec ~ 700 nSec Ref.1: Pin 4 = GND, Vin = 4 V return to zero pulse http://onsemi.com 5 0V MC33232 AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAA AAAAAAA AAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAA AAAAA AAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAA AAAAAAAAAAAAA AAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAA AAAAAAA AAAAAAA AAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAA AAAAAAA AAAAAAA AAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAA AAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAA AAAAA AAAAAAA AAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAA AAAAAAAAAA AAAAA AAAAA AAAAAAAAAAAAAAAAAA AAAAAAAAAA AAAAA AAAAAAAAA AAAAA AAAAAAAAAAAAAAAAAA AAAAAAAAAA AAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA MEASUREMENT CONDITION Item Condition Measurement Method VIH(ZCD) Pin 1 = 0 V Pin 5 = 3 mA Measure Pin 5 voltage at 3 mA to Pin 5 VIL(ZCD) Pin 2 = 1.1 V Pin 5 = -3 mA Measure Pin 5 voltage at -3 mA to Pin 5 IIB(CS) Pin 4 = 0 V Measure Pin 4 current VIO(CS) Pin 3 = 0 V Vin = Ref.1 Measure Pin 4 voltage when Pin 7 switch to low by increasing Pin 4 voltage from -0.3 V tPHL Vth(max) VOL(OUT) VOH(OUT) VO(max) tr tf 5V Pin 1 = 0 V Pin 2 = Vth(mult) + 0.5 V Pin 3 = 0.5 V Pin 4 = See right figure Vin = Ref.1 Vth(cs): Threshold voltage of Pin 4 (at Pin 2 = Vth(mult) + 0.5 V, Pin 3 = 0.5 V) Pin 1 = 0 V Pin 2 = 4.0 V Vth(ON) Vshut VH ICC Startup 0V Pin 7 tPHL 6V 0V Pin 3 = 3.0 V Vin = Ref.1 Measure Pin 4 voltage when Pin 7 switch to low by increasing Pin 4 voltage from 0 V Pin 1 = 0 V Pin 7 = 20 mA Measure Pin 7 voltage at 20 mA to Pin 7 SW2 = C Pin 7 = 200 mA Measure Pin 7 voltage at 200 mA to Pin 7 Pin 1 = 0 V Pin 7 = -20 mA Measure Pin 7 voltage at -20 mA to Pin 7 Pin 4 = GND Pin 7 = -200 mA Measure Pin 7 voltage at -200 mA to Pin 7 Vin = Ref.1 SW1 = C Pin 7 = -20 mA Measure Pin 7 voltage at -20 mA to Pin 7 4V Pin 1, 4 = 0 V SW3 = ON Vin Vin = See right figure Pin 7 0V f = 50 KHz VO(UVLO) Vth(cs) Pin 4 Pin 1 = 0 V SW1 = D 90% tf Pin 7 = 1.0 mA 90% 10% tr Measure Pin 7 voltage at 10 mA to Pin 7 SW1 = E Measure Pin 8 voltage when Pin 2 change to over 1 V by increasing Pin 8 voltage from 7 V Pin 4 = 0 V Measure Pin 8 voltage when Pin 2 change to under 1 V by increasing Pin 8 voltage from 15 V Vin = 0 V VH = Vth(on) - Vshut Pin 1 = 0 V SW1 = D Pin 1 = 0 V Pin 4 = 0 V SW3 = ON Measure Pin 8 current Operating Dynamic Operating Pin 2 = 2.5 V Pin 3 = 0.5 V Measure Pin 8 current Vin: Low = 0 V, High = 4 V fin = Square Wave @ TBD KHz Ref.1: Pin 4 = GND, Vin = 4 V return to zero pulse http://onsemi.com 6 MC33232 AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAA AAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAA AAAAAAAAAAAAA AAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAA AAAAAAAAAAAAA AAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAA AAAAAAAAAAAAA AAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAA AAAAAAAAAAAAA AAAAAAAAAAAAAAAAAA AAAAA AAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAA Item VZ Condition Measurement Method SW1 = E Pin 5 = 2.0 V Pin 8 = 25 mA Pin 1, 4 = 0 V Vin = 0 V Measure Pin 8 voltage Pin 1, 3 = 0 V 2V tDLY Pin 4 Measure Pin 7 frequency (FPin 7) 0V tDLY = 1 / FPin 7 f = 100 KHz 20 V Vth(on) Pin 8 POR SW1 = E Pin 4 = 0 V 0V Vin = 0 V Tstart 5V Pin 7 POR = Tstart - tDLY TEST CIRCUIT 12 V To follow unless otherwise noted SW1: A SW2: A SW3: OFF 1 2 A Voltage Feedback Input Compensation VCC 8 SW1 E Drive Output 7 B D ON SW3 3 Multiplier Input 4 Current Sense Input GND 6 Zero Current Detect 5 7 30 V 7.0 V OFF 1000 pF A SW2 4.7 kW Vin 2.0 V B C http://onsemi.com 28 V C TBD kW 110 20 VCC , SUPPLY VOLTAGE (VOLTS) V FB (0 V) , OVERVOLTAGE INPUT THRESHOLD (% V FB) MC33232 109 VCC = 12 V 108 107 106 -50 -25 0 25 50 Startup Threshold (VCC Increasing) 16 14 12 Minimum Operating Threshold (VCC Decreasing) 10 8 -50 100 75 18 -25 0 25 50 75 TA, AMBIENT TEMPERATURE (C) TA, AMBIENT TEMPERATURE (C) Figure 2. Overvoltage Comparator Input Threshold versus Temperature Figure 3. Undervoltage Lockout Thresholds versus Temperature 100 1200 t DLY, RESTART TIME DELAY ( ms) V FB , VOLTAGE FEEDBACK THRESHOLD CHANGE (mV) 20 VCC = 12 V Pins 1 to 2 10 0 -10 -20 -25 0 25 50 75 1000 900 800 700 -50 100 -25 0 25 50 75 TA, AMBIENT TEMPERATURE (C) TA, AMBIENT TEMPERATURE (C) Figure 4. Voltage Feedback Input Threshold Change versus Temperature Figure 5. Restart Timer Delay versus Temperature 100 1.7 2 VCC = 12 V V th , THRESHOLD VOLTAGE (VOLTS) V SAT, OUTPUT SATURATION VOLTAGE (V) -50 1100 Sink Saturation (Load to Ground) 0 Source Saturation (Load to VCC) -2 -4 0 80 160 240 1.5 Lower Threshold (Vin Decreasing) 1.4 1.3 -50 320 VCC = 12 V Upper Threshold (Vin Increasing) 1.6 -25 0 25 50 75 IO, OUTPUT LOAD CURRENT (mA) TA, AMBIENT TEMPERATURE (C) Figure 6. Output Saturation Voltage versus Load Current Figure 7. Zero Current Detector Input Threshold versus Temperature http://onsemi.com 8 100 MC33232 I1 ICC , SUPPLY CURRENT (mA) 20 3.30 V 2.0/div 2.50 V 0 0 V1 3.0/div 30 VCC, SUPPLY VOLTAGE (VOLTS) Figure 8. Error Amp Transient Response Figure 9. Supply Current versus Supply Voltage VCS , CURRENT SENSE PIN 4 THRESHOLD 5.0 ms / DIV 90% 10% 1.6 1.4 VCC = 12 V TA = 25C 1.2 1.0 0.8 0.6 0.4 0.2 Vpin 2 = 2.0 V 0 -0.2 0.6 1.4 2.2 3.0 Figure 10. Drive Output Waveform Figure 11. Restart Timer Delay versus Temperature VCS , CURRENT SENSE PIN 4 THRESHOLD 100 ns / DIV VM, MULTIPLIER PIN 3 INPUT VOLTAGE (V) 0.08 0.07 0.06 VCC = 12 V TA = 25C 0.05 0.04 0.03 0.02 Vpin 2 = 2.0 V 0.01 0 -0.12 -0.8 -0.4 0 0.04 0.08 0.12 0.16 0.20 IO, OUTPUT LOAD CURRENT (mA) Figure 12. Current Sense Input Threshold versus Multiplier Input (Expanded View) http://onsemi.com 9 0.24 3.8 MC33232 AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAA AAAA AAAAAAAAAAAAAAAAAA AAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAA AAAA AAAAAAAAAAAAAAAAAA AAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAA AAAA AAAAAAAAAAAAAAAAAA AAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAA AAAA AAAAAAAAAAAAAAAAAA AAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAA AAAAAAAAA AAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAA AAAAA AAAA AAAAAAAAAAAAAAAAAA AAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAA AAAA AAAAAAAAAAAAAAAAAA AAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAA AAAA AAAAAAAAAAAAAAAAAA AAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAA AAAA AAAAAAAAAAAAAAAAAA AAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAA AAAA AAAAAAAAAAAAAAAAAA AAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAA AAAA AAAAAAAAAAAAAAAAAA AAAAAAAAAA AAAAA AAAA AAAAAAAAAAAAAAAAAA AAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA PIN FUNCTION DESCRIPTION Name Pin No. Equivalent Circuit Function Vx This pin is an input for error amplifier to feedback the voltage from the converter output. Have the overvoltage detect circuit to cut off the drive out when the voltage is over 8% from setting value. PNP-L NP N-H VFB Voltage Feedback Input 1 PNP-S Vref Error Amplifier Output/Compensation Vx PMOS-L COMP This pin is an error amplifier output. Can do phase compensation or gain adjustment by this pin. NP N-L 2 PNP-S NP N-L NMOS-L Multiplier Input Vx Monitor the AC off line voltage using this input. Mult 3 PNP-S Current Sense Input VDD Control the output voltage by sensing the overcurrent at each cycle. This pin connects the RC filter and 1.5 V clamp diode. PMOS-L CS Multiout 4 http://onsemi.com 10 MC33232 AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAA AAAA AAAAAAAAAAAAAAAAAA AAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAA AAAA AAAAAAAAAAAAAAAAAA AAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAA AAAA AAAAAAAAAAAAAAAAAA AAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAA AAAA AAAAAAAAAAAAAAAAAA AAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAA AAAAAAAAA AAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAA AAAAA AAAA AAAAAAAAAAAAAAAAAA AAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAA AAAA AAAAAAAAAAAAAAAAAA AAAAAAAAAA AAAAA AAAA AAAAAAAAAAAAAAAAAA AAAAAAAAAA AAAAA AAAA AAAAAAAAAAAAAAAAAA AAAAAAAAAA AAAAA AAAAAAAAAA AAAAAAAAA AAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAA AAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAA AAAAAAAAAAAAAAAAAA AAAAA AAAA AAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAA AAAA AAAAAAAAAAAAAAAAAA AAAAA AAAA AAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA PIN FUNCTION DESCRIPTION Name Pin No. Equivalent Circuit Function VCC VDD Zero Current Detect Input VDD Control the output ON point to detect the zero current point on the coil. This pin has the 0.7 V and 5.3 V clamp diode internal. NP N-L ZCD PMOS-L 5 Ground VCC GND 6 Drive Out VCC Output Pin 8 Totem pole output. Pin 7 Power Supply 7 Vx NP N-M VCC 8 TMOS-M http://onsemi.com 11 MC33232 INTERNAL EQUIVALENT CIRCUIT Vx PNP-L NP N-H Pin 1 PNP-S Vref VCC Vx PMOS-L Pin 8 NP N-L Vx NP N-M Pin 2 Pin 7 PNP-S NP N-L NMOS-L TMOS-M VCC Vx Pin 3 Pin 6 PNP-S VCC VDD VDD VDD NP N-L PMOS-L PMOS-L Pin 4 Multiout http://onsemi.com 12 Pin 5 MC33232 SUGGESTED APPLICATION CIRCUIT AC 90 V to 268 V 100 k 1.0 m 8 28 V 1.4 V 3k + Zero Current Detector 2.5 V Reference 5 5.3 V 1.6 V/1.4 V + POR UVL O Timer 100 m 400 V/0.44 A 16 V 7 TSD + One-shot 330 m 5k Current Sensor 4 2p 0. 1 + Over Voltage Comparator 1.3 M 1.5 V 1.067 Vref Vref + Multiplier Err Amp 0.01 12 k 1.6 M 3 Quickstart 2 6 0.47 m http://onsemi.com 13 1 10 k MC33232 PACKAGE DIMENSIONS PDIP-8 P SUFFIX CASE 626-05 ISSUE L 8 NOTES: 1. DIMENSION L TO CENTER OF LEAD WHEN FORMED PARALLEL. 2. PACKAGE CONTOUR OPTIONAL (ROUND OR SQUARE CORNERS). 3. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 5 -B- 1 4 F -A- NOTE 2 L C J -T- N SEATING PLANE D H M K G 0.13 (0.005) M T A M B M http://onsemi.com 14 DIM A B C D F G H J K L M N MILLIMETERS MIN MAX 9.40 10.16 6.10 6.60 3.94 4.45 0.38 0.51 1.02 1.78 2.54 BSC 0.76 1.27 0.20 0.30 2.92 3.43 7.62 BSC --10_ 0.76 1.01 INCHES MIN MAX 0.370 0.400 0.240 0.260 0.155 0.175 0.015 0.020 0.040 0.070 0.100 BSC 0.030 0.050 0.008 0.012 0.115 0.135 0.300 BSC --10_ 0.030 0.040 MC33232 PACKAGE DIMENSIONS SOIC-8 D SUFFIX CASE 751-07 ISSUE AJ -X- NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. 6. 751-01 THRU 751-06 ARE OBSOLETE. NEW STANDARD IS 751-07. A 8 5 S B 0.25 (0.010) M Y M 1 4 -Y- K G C N DIM A B C D G H J K M N S X 45 _ SEATING PLANE -Z- 0.10 (0.004) H D 0.25 (0.010) M Z Y S X M J S MILLIMETERS MIN MAX 4.80 5.00 3.80 4.00 1.35 1.75 0.33 0.51 1.27 BSC 0.10 0.25 0.19 0.25 0.40 1.27 0_ 8_ 0.25 0.50 5.80 6.20 INCHES MIN MAX 0.189 0.197 0.150 0.157 0.053 0.069 0.013 0.020 0.050 BSC 0.004 0.010 0.007 0.010 0.016 0.050 0 _ 8 _ 0.010 0.020 0.228 0.244 SOLDERING FOOTPRINT* 1.52 0.060 7.0 0.275 4.0 0.155 0.6 0.024 1.270 0.050 SCALE 6:1 mm inches *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. SMARTMOS is a registered trademark of Motorola, Inc. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5773-3850 http://onsemi.com 15 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative MC33232/D