7MBP50TEA120 1200V / 50A 7 in one-package Econo IPM series Features * Temperature protection provided by directly detecting the junction temperature of the IGBTs * Low power loss and soft switching * High performance and high reliability IGBT with overheating protection * Higher reliability because of a big decrease in number of parts in built-in control circuit Maximum ratings and characteristics Absolute maximum ratings(at Tc=25C unless otherwise specified) Item Bus voltage DC Surge Short operating Collector-Emitter voltage *1 Collector current Brake Inverter DC 1ms DC Collector power dissipation One transistor *3 Collector current DC 1ms Forward current diode Collector power dissipation One transistor *3 Supply voltage of Pre-Driver *4 Input signal voltage *5 Input signal current Alarm signal voltage *6 Alarm signal current *7 Junction temperature Operating case temperature Storage temperature Solder temperature *8 Isolating voltage (Terminal to base, 50/60Hz sine wave 1min.) Screw torque Mounting (M5) Symbol Rating Min. Max. VDC 0 0 400 0 -0.5 -0.5 -0.5 -20 -40 - VDC(surge) V SC VCES IC ICP -IC PC IC ICP IF PC V CC Vin Iin VALM IALM Tj Topr Tstg Tsol Viso 900 1000 800 1200 50 100 50 287 15 30 15 139 20 Vcc+0.5 3 Vcc 20 150 100 125 260 AC2500 3.5 Unit V V V V A A A W A A A W V V mA V mA C C C C V N*m Note *1 : Vces shall be applied to the input voltage between terminal P and U or V or W or DB, N and U or V or W or DB *2 : 125C/FWD Rth(j-c)/(Ic x VF MAX)=125/0.86/(50 x 2.0) x 100>100% *3 : Pc=125C/IGBT Rth(j-c)=125/0.44=287W [Inverter] Pc=125C/IGBT Rth(j-c)=125/0.90=139W [Brake] *4 : VCC shall be applied to the input voltage between terminal No.4 and 1, 8 and 5, 12 and 9, 14 and 13 *5 : Vin shall be applied to the input voltage between terminal No.3 and 1, 7 and 5, 11 and 9, 16,17,18 and 13. *6 :VALM shall be applied to the voltage between terminal No.2 and 1, No6 and 5, No10 and 9, No.19 and 13. *7 : IALMshall be applied to the input current to terminal No.2,6,10 and 19. *8 : Immersion time 101sec. http://store.iiic.cc/ 7MBP50TEA120 IGBT-IPM Electrical characteristics (at Tc=Tj=25C, Vcc=15V unless otherwise specified.) Main circuit Inverter Item Collector current at off signal input Collector-Emitter saturation voltage Forward voltage of FWD Brake Collector current at off signal input Collector-Emitter saturation voltage Forward voltage of Diode Turn-on time Turn-off time Reverse recovery time Symbol ICES VCE(sat) VF ICES VCE(sat) VF ton toff trr Condition Min. VCE=1200V Vin terminal open. Ic=50A Terminal Chip -Ic=50A Terminal Chip Typ. Max. 2.2 1.6 1.9 1.9 - 1.0 3.1 2.0 1.0 2.6 3.3 3.6 0.3 1.2 - VCE=1200V Vin terminal open. Terminal Ic=15A Chip Terminal -Ic=15A Chip VDC=600V,Tj=125C IC=50A Fig.1, Fig.6 VDC=600V, IF=50A Fig.1, Fig.6 Unit mA V V mA V V s Control circuit Item Supply current of P-line side pre-driver(one unit) Supply current of N-line side pre-driver Input signal threshold voltage (on/off) Symbol Iccp ICCN Vin(th) Input zener voltage Alarm signal hold time VZ tALM Current limit resistor RALM Condition Switching Frequency : 0 to 15kHz Tc=-20 to 125C Fig.7 ON OFF Rin=20k ohm Tc=-20C Fig.2 Tc=25C Fig.2 Tc=125C Fig.2 Alarm terminal Min. Typ. Max. 15 45 1.00 1.35 1.70 1.25 1.60 1.95 8.0 1.1 2.0 4.0 1425 1500 1575 Unit mA mA V V V ms ms ms ohm Protection Section ( Vcc=15V) Item Over Current Protection Level of Inverter circuit Over Current Protection Level of Brake circuit Over Current Protection Delay time SC Protection Delay time IGBT Chip Over Heating Protection Temperayure Level Over Heating Protection Hysteresis Under Voltage Protection Level Under Voltage Protection Hysteresis Symbol IOC IOC tDOC tSC TjOH Condition Min. Typ. Max. 5 - 8 - 20 0.5 12.5 - 75 23 Tj=125C Tj=125C Tj=125C Tj=125C Fig.4 Surface of IGBT chips 150 - TjH V UV VH 11.0 0.2 Thermal characteristics( Tc=25C) Item Junction to Case thermal resistance *9 Inverter Brake IGBT FWD IGBT Case to fin thermal resistance with compound Symbol Rth(j-c) Rth(j-c) Rth(j-c) Rth(c-f) Min. - Typ. 0.05 Max. 0.44 0.86 0.90 - Unit C/W C/W C/W C/W Min. Typ. Max. Unit *9 For 1device, Case is under the device Noise Immunity ( VDC=300V, Vcc=15V, Test Circuit Fig.5) Item Common mode rectangular noise Common mode lightning surge Condition Pulse width 1s, polarity ,10minuets Judge : no over-current, no miss operating Rise time 1.2s, Fall time 50s Interval 20s, 10 times Judge : no over-current, no miss operating 2.0 - - kV 5.0 - - kV Symbol V DC V CC - Min. 13.5 2.5 Typ. 15.0 - Max. 800 16.5 3.0 Unit V V Nm Symbol Wt Min. - Typ. 270 Max. - Unit g Recommendable value Item DC Bus Voltage Operating Supply Voltage of Pre-Driver Screw torque (M5) Weight Item Weight http://store.iiic.cc/ Unit A A s s C C V V 7MBP50TEA120 IGBT-IPM Vin(th) Vin On Vin(th) trr 90% 50% Ic 90% 10% toff ton Figure 1. Switching Time Waveform Definitions ) on on Gate On Vge (Inside IPM ) Fault (Inside IPM off off /Vin Gate Off normal alarm /ALM tALM > Max. 1 tALM > t ALM 2ms(typ.) 3 Max. 2 Fault : Over-current,Over-heat or Under-voltage Figure 2. Input/Output Timing Diagram tsc Ic Ic Ic I ALM I ALM I ALM Figure.4 Definition of tsc Vcc PP IPM IPM 20 k DC 15V VccU 20k DC 15V VinU P IPM DC 300V 600V GND N Ic U Figure 6. Switching Characteristics Test Circuit SW1 GNDU V 20k DC 15V + + Vin HCPL 4504 CT L SW2 Earth Vcc VinX GND AC200V AC400V + W Icc A 4700p N Vcc P Noise DC 15V Cooling Fin IPM U Vin V P.G +8V fsw W GND N Figure 5. Noise Test Circuit Figure 7. Icc Test Circuit http://store.iiic.cc/ 7MBP50TEA120 IGBT-IPM Block diagram P VccU 4 VinU 3 Pre- Driver ALMU 2 RALM 1.5k Vz GNDU 1 VccV 8 VinV 7 U Pre- Driver ALMV 6 RALM 1.5k Vz GNDV 5 VccW 12 VinW 11 ALMW 10 V Pre- Driver RALM 1.5k Vz GNDW 9 Vcc 14 VinX 16 W Pre- Driver Vz GND VinY 13 17 Pre- Driver Vz VinZ Pre-drivers include following functions 1.Amplifier for driver 18 Pre- Driver Vz 2.Short circuit protection 3.Under voltage lockout circuit B VinDB 15 ALM 19 4.Over current protection 5.IGBT chip over heating protection Pre- Driver RALM 1.5k Vz N MBCFM Outline drawings, mm Mass : 270g http://store.iiic.cc/ 7MBP50TEA120 IGBT-IPM Characteristics Control circuit characteristics (Representative) Input signal threshold voltage vs. Power supply voltage (typ.) Power supply current vs. Switching frequency Tc=125C (typ.) 2.5 P-side N-side 40 Input signal threshold voltage : Vin(on),Vin(off) (V) Power supply current : Icc (mA) 50 Vcc=17V Vcc=15V Vcc=13V 30 20 Vcc=17V Vcc=15V Vcc=13V 10 0 0 5 10 15 20 Switching frequency : fsw (kHz) 12 10 8 6 4 2 1 0.5 13 14 15 16 17 Power supply voltage : Vcc (V) 18 40 60 80 100 120 0.8 0.6 0.4 0.2 0 20 140 Junction temperature : Tj (C) 40 60 80 100 120 Junction temperature : Tj (C) 140 Over heating characteristics TjOH,TjH vs. Vcc (typ.) Alarm hold time vs. Power supply voltage (typ.) 200 Over heating protection : TjOH (C) OH hysterisis : TjH (C) 3 2.5 Tc=100C 2 Tc=25C 1.5 1 0.5 0 12 } Vin(on) 1.5 1 Under voltage hysterisis : VH (V) Under voltage : VUVT (V) } Vin(off) Under voltage hysterisis vs. Jnction temperature (typ.) 14 0 20 2 0 12 25 Under voltage vs. Junction temperature (typ.) Alarm hold time : tALM (mSec) Tj=25C Tj=125C 13 14 15 16 17 18 TjOH 150 100 50 TjH 0 12 Power supply voltage : Vcc (V) http://store.iiic.cc/ 13 14 15 16 17 Power supply voltage : Vcc (V) 18 7MBP50TEA120 IGBT-IPM Main circuit characteristics (Representative) Collector current vs. Collector-Emitter voltage (typ.) Tj=25C / Chip Collector current vs. Collector-Emitter voltage (typ.) Tj=25C / Terminal 100 Vcc=15V 80 Collector Current : Ic (A) Collector Current : Ic (A) 100 Vcc=17V 60 Vcc=13V 40 20 60 Vcc=17V Vcc=13V 40 0 0 0.5 1 1.5 2 2.5 3 Collector-Emitter voltage : Vce (V) 3.5 0 0.5 1 1.5 2 2.5 3 Collector-Emitter voltage : Vce (V) 3.5 Collector current vs. Collector-Emitter voltage (typ.) Tj=125C / Terminal Collector current vs. Collector-Emitter voltage (typ.) Tj=125C / Chip 100 80 Collector Current : Ic (A) 100 Collector Current : Ic (A) Vcc=15V 20 0 Vcc=15V Vcc=17V 60 Vcc=13V 40 20 80 Vcc=15V Vcc=17V 60 Vcc=13V 40 20 0 0 0 0.5 1 1.5 2 2.5 3 3.5 Collector-Emitter voltage : Vce (V) 0 0.5 1 1.5 2 2.5 3 Collector-Emitter voltage : Vce (V) Forward current vs. Forward voltage (typ.) Chip Forward current vs. Forward voltage (typ.) Terminal 100 100 80 80 25C Forward Current : If (A) Forward Current : If (A) 80 125C 60 40 20 3.5 25C 60 125C 40 20 0 0 0 0.5 1 1.5 2 2.5 Forward voltage : Vf (V) 0 0.5 1 1.5 Forward voltage : Vf (V) http://store.iiic.cc/ 2 2.5 7MBP50TEA120 IGBT-IPM 20 15 Eon 10 Eoff 5 Err Switching Loss vs. Collector Current (typ.) Edc=600V,Vcc=15V,Tj=125C Switching loss : Eon,Eoff,Err (mJ/cycle) Switching loss : Eon,Eoff,Err (mJ/cycle) Switching Loss vs. Collector Current (typ.) Edc=600V,Vcc=15V,Tj=25 C 20 Eon 15 10 Eoff 5 Err 0 0 0 20 40 60 80 0 100 20 40 60 80 100 Collector current : Ic (A) Collector current : Ic (A) Transient therm al resistance (m ax.) R e ve rs ed bias ed sa fe ope ra ting a re a Vc c=1 5V, Tj<= 125 C (m in .) 1 Therm al resistance : Rth(j-c) (C/W ) 70 0 60 0 C ollecto r curre nt : Ic (A) 50 0 40 0 S C SO A ( no n- repe titive puls e) 30 0 20 0 FW D IG BT 0.1 10 0 R BSO A (R epe titive puls e) 0.01 0 0 20 0 400 60 0 800 1 00 0 1 200 0.0 01 140 0 0.01 1 Pulse w idth :Pw (sec) C olle ctor- Emitter voltage : V ce (V) Power derating for IG BT (m ax.) (per dev ice) Power derating for FW D (max.) (per dev ice) 500 200 Collecter Power Dissipation : Pc (W ) Collecter Power Dissipation : Pc (W ) 0.1 400 300 200 100 0 150 100 50 0 0 20 40 60 80 100 120 140 160 0 Case Tem perature : Tc (C) 20 40 60 80 100 120 Case Tem perature : Tc (C) http://store.iiic.cc/ 140 160 7MBP50TEA120 IGBT-IPM Switching tim e vs. Collector current (typ.) Edc=600V,Vcc=15V,Tj= 125 C Switching time vs. Collector current (typ.) Edc=600V,Vcc=15V,Tj=25 C 10000 Switching time : ton,toff,tf (nSec ) Switching time : ton,toff,tf (nSec ) 10000 toff 1000 ton 100 tf ton 1000 tf 100 10 10 0 10 20 30 40 50 60 Collector current : Ic (A) 70 80 trr125C trr25C 100 Irr125C Irr25C 10 1 0 10 20 30 40 50 60 Forward current:IF(A) 0 10 20 30 40 50 60 Collector current : Ic (A) Reverse recovery characteristics trr,Irr vs.IF (typ.) Reverse recovery current:Irr(A) Reverse recovery time:trr(nsec) toff 70 80 http://store.iiic.cc/ 70 80 7MBP50TEA120 IGBT-IPM Characteristics Dynamic Brake Characteristics (Representative) Collector current v s. Collector-Emitter v oltage (typ.) Tj=25C 40 Vcc=15V Collector C urrent : Ic (A) Collector Current : Ic (A) 40 Collector current v s. Collector-Emitter v oltage (typ.) Tj=125C 30 Vcc=1 7V Vcc=1 3V 20 10 0 30 Vcc=1 7V Vcc=13V 20 10 0 0 0.5 1 1.5 2 2.5 3 3.5 4 0 0.5 1 1.5 2 2.5 3 3.5 Collector-Emitter voltage : Vce (V) Collector-Em itter voltage : Vce (V) Transient therm al resistance (m ax.) R e ve rs ed bias ed sa fe ope ra ting a re a Vc c=1 5V, Tj<= 125 C (min .) 1 4 21 0 IG BT 18 0 15 0 C ollecto r curre nt : Ic (A) Therm al resistance : Rth(j-c) (C/W ) Vcc=1 5V 0.1 12 0 S CSO A (non-repetitive puls e) 90 60 30 R BSO A (R epe titive puls e) 0 0.01 0.0 01 0.01 0.1 1 0 Power derating for IGBT (max.) (per dev ice) Collecter Power Dissipation : Pc (W ) 200 150 100 50 0 20 40 60 80 100 400 60 0 800 1 00 0 C ollector -Emitte r v oltage : V c e ( V) Pulse w idth :Pw (sec) 0 20 0 120 140 160 Case Tem perature : Tc (C) http://store.iiic.cc/ 1200 140 0