Click here for production status of specific part numbers. MAX98357 Development Board/ Evaluation System (WLP) Evaluates: MAX98357A/MAX98357B (WLP) General Description Features The MAX98357 development board (DEV board) is a fully assembled and tested PCB that evaluates the MAX98357 I2S digital input Class D power amplifier. The DEV board operates from a single 2.5V to 5.5V DC power supply and is capable of delivering 3.2W into a 4 load. The device outputs can be connected directly to a speaker load for filterless applications. However, a filter can be added to ease evaluation. The MAX98357A accepts standard I2S data and the MAX98357B accepts left-justified digital audio data. Both versions also support 8-channel TDM audio data. 2.5V to 5.5V Single-Supply Operation Only a Single External Component (VDD Capacitor) Required in Many Applications I2S, Left-Justified, or TDM Input Five Selectable Gains (3db, 6dB, 9dB, 12dB, and 15dB) Audio Channel Select (Left, Right, and Mono Mix) Filterless Operation Optional Class D Output Filters for Ease of Evaluation The MAX98357 evaluation system (EV system) includes the MAX98357 DEV board and Maxim Integrated's audio interface board (MAXAUDINT001# board). Proven PCB Layout Fully Assembled and Tested The MAXAUDINT001# board provides an easy-to-use USB audio-to-I2S converter. This allows for any computer to become a digital audio source, which can be used to evaluate the devices. The MAXAUDINT001# board can also be used to power the MAX98357. This allows for a complete evaluation from a single USB connection. Ordering Information appears at end of data sheet. 2.5V TO 5.5V 10F 0.1F VDD PCM AUDIO INTERFACE BOARD 19-6833; Rev 2; 9/18 MAX98357 LRCLK BCLK DIN SD_MODE Figure 1. Simplified Block Diagram GAIN_SLOT DIGITAL AUDIO INTERFACE DAC CLASS D OUTPUT STAGE OUTP OUTN Evaluates: MAX98357A/MAX98357B (WLP) MAX98357 Development Board/ Evaluation System (WLP) Quick Start Detailed Description of Hardware Recommended Equipment * MAX98357 EV system * 2.5V to 5.5V, 2A DC power supply * USB audio source (from computer through an audio media player such as iTunes(R) or Windows Media(R) player) * 4 or 8 speaker Procedure The EV system is fully assembled and tested. Follow the steps below to verify board operation. Caution: Do not turn on the power supply until all connections are completed. 1) Verify that headers and switches are configured as follows: JU2: Pins 1-3 (selects left channel) JU4: Pins 1-2 (power MAXAUDINT001# board) routed from the JU5: Pins 1-5 (12dB GAIN_SLOT) JU6: Pins 2-3 (power routed from external supply) SW1: Position 1-2 (part is on) 2) Set the power-supply output to 5V. Disable the power supply. 3) Connect the power-supply ground terminal to GND and the power-supply positive terminal to VIN on the DEV board. 4) With the audio source disabled, connect the USB audio source to J1 on the DEV board. 5) Connect the MAXAUDINT001# board to J1 on the DEV board. 6) Connect the speaker across the OUTP and OUTN test points. 7) Enable the power-supply output. 8) Enable the audio source. 9) Verify that the speakers are playing the audio source signal. The MAX98357 EV system is designed to allow a thorough evaluation of the MAX98357 I2S digital input Class D power amplifier. The DEV board can be used by itself as a stand-alone evaluation board and driven directly by audio test equipment. The DEV board can also be used in conjunction with the MAXAUDINT001# board, which allows for any computer to become an I2S digital audio source. The MAXAUDINT001# board has DC regulators that can be used to power the device. This allows for quick evaluation from a single USB connection. Note that powering the device from the MAXAUDINT001# board does not allow for high-power evaluation as the input current is limited and evaluation with a speaker is not recommended. Jumpers JU4 and JU6 are used to power the device from the MAXAUDINT001# board or external supplies connected to test points VIN and VDDIO on the DEV board. The DEV board operates from a single 2.5V to 5.5V DC power supply and is capable of delivering 3.2W into a 4 load and 1.75W into an 8 load. The device outputs can be connected directly to a speaker for filterless applications. However, a filter can be added to ease evaluation. The LRC components needed for evaluation of a filtered output are included with the EV kit. The MAX98357A accepts standard I2S data and the MAX98357B accepts left-justified digital audio data. Both versions also support 8-channel TDM audio data. Filterless Output The DEV board filterless outputs (OUTP, OUTN) can be connected directly to a speaker load without any filtering. Use the OUTP and OUTN test points to connect the speaker directly to the device output. Filtered Output Audio analyzers typically cannot accept the Class D amplifier's pulse-width modulated (PWM) signals at their inputs. Therefore, the DEV board features optional lowpass filters at the outputs to ease evaluation. As shipped, the DEV board's lowpass filter LRC components are unpopulated and L1, L2 are shorted on the PCB. To use the filtered output posts (FOUTP, FOUTN), remove the shorts on L1 and L2 and install components L1, L2, C3- C7, and R5, R6. Use the output posts to connect the filtered outputs to the audio analyzer. The default lowpass filters at the DEV board output are optimized for a 4 speaker. iTunes is a registered trademark of Apple Inc. Windows Media is registered trademark and registered service mark of Microsoft Corporation. www.maximintegrated.com Maxim Integrated 2 MAX98357 Development Board/ Evaluation System (WLP) EMI Considerations and Optional Ferrite Bead Filter In applications where speaker leads/wires are long (exceeding approximately 12 inches), additional EMI suppression can be achieved by using a filter constructed from a ferrite bead (FB1, FB2) and a capacitor to ground (C8, C9) (Figure 2). Use a ferrite bead with low DC resistance, high frequency impedance (> 600MHz) between 100 and 600, and rated for at least 1A. The capacitor value varies based on the ferrite bead chosen and the actual speaker lead length. Select a capacitor less than 1nF with the value based upon optimizing EMI performance. Do not use the optional ferrite bead filter in conjunction with the optional Class D Filter. Jumper Selection Selectable (GAIN_SLOT) The DEV board features a 5-pin jumper (JU5) to control the device's five programmable gain settings. In TDM mode, the gain is fixed at 12dB and the GAIN_SLOT pin is repurposed for slot selection. See Table 1 for gain-control configuration. MAX98357A OUTP MAX98357B OUTN Evaluates: MAX98357A/MAX98357B (WLP) SD_MODE Input The DEV board features a 4-pin jumper (JU2) to control both the audio channel that is sent to the amplifier output, along with shutdown mode. JU2 is used to select the stereo input data between the left channel, right channel, and the sum of the left/right channels. JU4 must be set to pins 1-2 and a voltage applied to the +3.3V PCB pad for proper operation. See Table 2 for shunt positions. TDM Mode In TDM mode, the device has a fixed gain of 12dB and the GAIN_SLOT pin becomes repurposed for slot selection. The device accepts 8-channel TDM data. The data can be either 16 bits or 32 bits wide. The GAIN_SLOT pin and SD_MODE are used to select which of 8 channels of TDM data the part responds to, as shown in Table 3. Table 2. JU2 Jumper Selection (SD_MODE) SHUNT POSITION AUDIO CHANNEL SD_MODE PIN 1-2 Connected to VDDIO through R3 (small resistor) 1-3* Connected to VDDIO through a 2k resistor 1-4 Connected to VDDIO through R4 (large resistor) Right Left Mono mix (left + right)/2 *Default position. Table 3. TDM Mode Channel Selection (JU2, JU5) Figure 2. Optional Ferrite Bead Filter Table 1. JU5 Jumper Selection (GAIN_SLOT) JU2 JU5 CHANNEL BITS Connected low X OFF N/A 1-3 1-5 0 16 or 32 1-3 1-3 1 16 or 32 SHUNT POSITION GAIN_SLOT PIN MAXIMUM GAIN_SLOT (dB) Connected to VDD through 100k resistor R1 1-3 OPEN 2 16 or 32 1-2 3 1-3 1-2 3 16 or 32 1-3 Connected to VDD 6 1-3 1-4 4 16 or 32 1-4 Connected to GND through 100k resistor R2 15 1-4 1-5 5 16 or 32 1-4 OPEN 6 16 or 32 1-5* Connected to GND 12 1-4 1-3 7 16 or 32 Unconnected 9 Not installed *Default position. www.maximintegrated.com Maxim Integrated 3 MAX98357 Development Board/ Evaluation System (WLP) Shutdown Mode The device features a low-power shutdown mode that is activated by setting jumper SW1 to pins 2-3. To exit shutdown mode, set SW1 to pins 1-2 and select the desired stereo input channel using jumper JU2. See Table 4 for shunt positions. External/Internal VDDIO (+1.8V to +3.3V) On the DEV board, a logic voltage from a control interface is needed for proper selection of the stereo input channel through SD_MODE. This voltage can be applied externally at the VDDIO test point or it can be provided from circuitry on the MAXAUDINT001# board. See Table 5 for JU4 jumper selection. Other logic voltages can be used other than +3.3V. If you want to use other logic voltages, resistors R3 and R4 must be adjusted. Refer to the SD_MODE and Shutdown Operation section in the MAX98357 IC data sheet for more information. VDD Input Supply (+2.5V to +5.5V) The device can accept an input supply from +2.5V to +5.5V. This voltage can be applied externally at the VDD and GND PCB pads, or it can be provided from the MAXAUDINT001# board. See Table 6 for JU6 jumper selection. Audio Interface Board (MAXAUDINT001# Board) The MAXAUDINT001# board provides USB-to-I2S data conversion, as well as DC regulators that can be used to power the devices. The USB-to-I2S converter on the MAXAUDINT001# board allows for any computer to become an I2S digital audio source without requiring additional driver installation. On the MAXAUDINT001# board, set SW1 to "demo" and set the I2S switch to connected to source audio by USB. This allows for a quick evaluation from a single USB connection. Using the MAXAUDINT001# board as a power supply for high-power evaluation is not recommended as the input current is limited. For high-power evaluation, use an external supply connected to VIN. Evaluates: MAX98357A/MAX98357B (WLP) Driving I2S Directly To drive I2S directly, apply signals at the BCLK, LRCLK, and SDIN test points, or on the J3 header, or between J3 pins 1-2 at the appropriate locations (signal and ground are labeled on the board). Evaluating the MAX98357B The MAX98357 DEV board comes with a MAX98357A populated on the board, but can also be used to evaluate the MAX98357B. To evaluate the MAX98357B, carefully remove the MAX98357A (U1) device from the board and replace with the MAX98357BEWL+. No other component changes are required. Table 4. SW1 Jumper Selection SWITCH POSITION VDDIO VOLTAGE DEVICE OPERATION 1-2* VDDIO determined by JU4 jumper position Normal (input channel selected through JU2 setting) 2-3 Connected to GND Shutdown *Default position. Table 5. JU4 Jumper Selection (VDDIO) SHUNT POSITION LOGIC VOLTAGE (VDDIO) 1-2* 3.3V supplied by the MAXAUDINT001# board connected to J1 header. 2-3 User-supplied external power supply applied at the VDDIO test point. *Default position. Table 6. JU6 Jumper Selection (VDD) SHUNT POSITION INPUT VOLTAGE (VDD) 1-2* VDD supplied from the MAXAUDINT001# board connected to the J1 header. 2-3 User-supplied external power supply applied at the VIN PCB pad. *Default position. www.maximintegrated.com Maxim Integrated 4 Evaluates: MAX98357A/MAX98357B (WLP) MAX98357 Development Board/ Evaluation System (WLP) Component List DESIGNATION QTY BCLK, DIN, LRCLK 3 Orange multipurpose test points 1 10F 10%, 6.3V X5R ceramic capacitor (0603) Murata GRM188R60J106K C1 DESCRIPTION C2 1 0.1F 10%, 16V X7R ceramic capacitor (0402) Murata GRM155R71C104K C3-C12 0 Not installed, ceramic capacitors (0402) FB1, FB2 2 0 5% resistors (0603) FOUTN, FOUTP, GND, VIN 4 Binding posts FOUTN, FOUTP, GND (x2), VDD 5 20G plated solid copper bus wire, 0.25in U-shaped wire loop GND (x4), OUTN 5 Black multipurpose test points (63 mil drill size) J1 1 26-pin (2 x 13) dual-row rightangle header, 0.1in centers DESIGNATION QTY DESCRIPTION R4 1 634k 1% resistor (0603) R5, R6 0 Not installed, resistors (0402) R7-R9 3 0 5% resistors (0603) U1 1 I2S input Class D audio amplifier (16 WLP) Maxim MAX98357AEWL+ VDDIO 1 Red multipurpose test point (63 mil drill size) SW1 1 SPDT jumper switch, 0.1in centers -- 4 Shunts -- 1 PCB: MAX98357 WLP EVKIT DEVELOPMENT BOARD OPTIONAL CLASS D FILTER COMPONENTS C3-C7 7 0.22F 10%, 6.3V X5R ceramic capacitors (0402) TDK C1005X5R0J224K L1, L2 2 22H, 1A inductors (6.2mm x 6.3mm) TOKO A916CY-220M R5, R6 2 22 5% resistors (0402) J3 1 6-pin header JU2 1 4-pin header, 0.1 in centers JU4, JU6 2 3-pin headers, 0.1 in centers JU5 1 5-pin header, 0.1 in centers 0 Not installed, 22H inductors (6.2mm x 6.3mm)--short (PC trace) TOKO D63CB series part TOKO A916CY-220M OUTP 1 White multipurpose test point (63 mil drill size) C8, C9 2 680pF 10% 50V X54 ceramic capacitors (0402) TDK CGA2B1C0G2A681J050BE R1, R2 2 100k 5% resistors (0603) R3 1 226k 1% resistor (0603) FB1, FB2 2 Murata BLM18SG331TN1 (0603) L1, L2 OPTIONAL I2S CONDITIONING COMPONENTS R7-R9 3 51 5% resistors (0402) C10-C12 3 18pF 5%, 50V, C0G ceramic capacitors (0402) OPTIONAL EMI FILTERING COMPONENTS Component Suppliers SUPPLIER PHONE WEBSITE Murata Americas 770-436-1300 www.murataamericas.com TDK Corp. 847-803-6100 www.component.tdk.com TOKO America, Inc. 847-297-0070 www.tokoam.com Note: Indicate that you are using the MAX98357 when contacting these component suppliers. www.maximintegrated.com Maxim Integrated 5 MAX98357 Development Board/ Evaluation System (WLP) Evaluates: MAX98357A/MAX98357B (WLP) Figure 3. MAX98357 DEV Board Schematic www.maximintegrated.com Maxim Integrated 6 MAX98357 Development Board/ Evaluation System (WLP) Evaluates: MAX98357A/MAX98357B (WLP) MAX98357 EV Kit PCB Layouts 1.0" MAX98357 DEV Board Silkscreen--Top 1.0" MAX98357 DEV Board PCB Layout--Component Side 1.0" MAX98357 DEV Board PCB Layout--Layer 2 www.maximintegrated.com Maxim Integrated 7 MAX98357 EV Kit PCB Layouts (continued) MAX98357 Development Board/ Evaluation System (WLP) Evaluates: MAX98357A/MAX98357B (WLP) MAX98357 EV Kit PCB Layouts (continued) 1.0" MAX98357 DEV Board PCB Layout--Layer 3 MAX98357 DEV Board PCB Layout--Solder Side Ordering Information PART MAX98357DEV#WLP MAX98357EVSYS#WLP TYPE Development Board (DEV Board only) Evaluation System Kit (DEV + MAXAUDINT001# Boards) #Denotes RoHS compliant. www.maximintegrated.com Maxim Integrated 8 MAX98357 Development Board/ Evaluation System (WLP) Evaluates: MAX98357A/MAX98357B (WLP) Revision History REVISION NUMBER REVISION DATE 0 10/13 Initial release 1 4/14 Added Evaluating the MAX98357B section and updated Figures 2 and 7 9/18 Changed all instances of "AUDINT001" to "MAXAUDINT001#," added EMI filtering information and new Figure 2, updated Component List table 2 PAGES CHANGED DESCRIPTION -- 4-6, 8 1-9 For pricing, delivery, and ordering information, please visit Maxim Integrated's online storefront at https://www.maximintegrated.com/en/storefront/storefront.html. Maxim Integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim Integrated product. No circuit patent licenses are implied. Maxim Integrated reserves the right to change the circuitry and specifications without notice at any time. Maxim Integrated and the Maxim Integrated logo are trademarks of Maxim Integrated Products, Inc. (c) 2018 Maxim Integrated Products, Inc. 9