SW1-020080RN1NF - MITEQ, Inc.

SINGLE-POLE SINGLE-THROW SWITCHES

FEATURES

• Multioctave bands 0.2 to 18 GHz

• Current or TTL control

• Low insertion loss

• High isolation

• Ultra high speed models (5 ns) available

• Drop-in models available

Frequency

Insertion Rise/Fall On/Off On/Off DC Power

Range Model Loss Isolation VSWR* Time Time Time Positive Negative

(GHz) Number (dB, Max.) (dB, Min.) (Max.) Type (ns, Typ.) (ns, Typ.) (ns, Max.) (mA, Max.) (mA, Min.)

STANDARD, MULTIOCTAVE BAND MODELS

SW1-002020RN1NF 1.7 70 1.6:1 Reflective 10/10 20 35 35 70

0.2–2 SW1-002020AN1NF 1.8 75 1.6:1 Absorptive 10/10 20 35 35 70

0.5–2 SW1-005020RN1NF 1.5 80 1.6:1 Reflective 10/10 20 35 35 70

SW1-005020AN1NF 1.7 75 1.6:1 Absorptive 10/10 20 35 35 70

SW1-020080RN1NF 2 80 1.7:1 Reflective 10/10 20 35 35 70

2–8 SW1-020080AN1NF 2.2 70 1.7:1 Absorptive 10/10 20 35 35 70

4–12 SW1-040120RN1NF 2.2 80 1.7:1 Reflective 10/10 20 35 35 70

SW1-040120AN1NF 2.6 65 1.7:1 Absorptive 10/10 20 35 35 70

2–18 SW1-020180RN1NF 3 80 2:1 Reflective 10/10 20 35 35 70

SW1-020180AN1NF 3 60 2:1 Absorptive 10/10 20 35 35 70

1–18 SW1-010180RN1NF 3 70 2:1 Reflective 10/10 20 35 35 70

SW1-010180AN1NF 3.2 60 2:1 Absorptive 10/10 20 35 35 70

0.8–18 SW1-008180RN1NF 4 70 2:1 Reflective 5 35 40 35 35

0.1–20 SW1-001200RN1NF 5 80 2:1 Reflective 10 35 40 35 35

0.5–2 SW1-005020AN1NF 1.8 75 1.6:1 Absorptive 8 35 40 35 35

0.5–18 SW1-005180RN1NF 3 70 2:1 Reflective 10 35 40 35 70

2–2.2 SW1-020022RN1NF 1 40 1.7:1 Reflective 20 35 40 70 70

2–8 SW1-020080AN1NF 2 55 1.7:1 Absorptive 5 35 40 35 35

3–3.4 SW1-030034AN1NF 1 60 1.5:1 Absorptive 10 35 40 35 70

3–9 SW1-030090RN1NF 1.7 60 1.7:1 Reflective 10 35 40 35 70

3.5–4.5 SW1-035045AN1NF 2 80 1.7:1 Absorptive 20 35 40 60 60

9–9.2 SW1-090092RN1NF 1 70 1.7:1 Reflective 20 35 40 35 70

9.1–9.7 SW1-091097AI2NF 2.6 65 1.7:1 Absorptive 10 30 35 35 70

Electrical performance of multioctave models can be optimized over narrower bandwidths, or for a particular parameter. Electrical options include: Lower

insertion loss, lower VSWR, higher isolation, high power and flat amplitude response. Mechanical/Control options include: Custom packaging, single

supply operation, and ultra-fast on/off time. Consult MITEQ for options.

*For reflective models, VSWR is not specified in the “Off” state. For absorptive models, VSWR in the “Off” state is defined for port J2 only.

OPTIMIZED PERFORMANCE MODELS

100 Davids Drive, Hauppauge, NY 11788 • TEL: (631) 436-7400 • FAX: (631) 436-7430 • www.miteq.com

SINGLE-POLE SINGLE-THROW SWITCHES (CONT.)

SPST OUTLINE DRAWING

0.40

[10.16]

"SMA" FEMALE

CONNECTOR,

TYP. (2) PLACES

0.10 [2.54] TYP.

0.80 [20.32]

0.60 [15.25]

0.36 [9.14] MAX.

0.38

[9.65]

TYP.

0.40 [10.16]

0.104 [2.64] DIA. THRU,

4 HOLES TYP.

0.11 [2.79]

TYP.

+5 V -12 V

0.11 [2.79]

TYP. 0.18 [4.57]

0.50

[12.70]

0.80 [20.32]

0.10 [2.54]

1.00 [25.40] GND. PIN

0.18

[4.57]

0.40 [10.16]

0.18 [4.57]

GENERAL NOTES:

1. Dimensions shown in brackets [ ] are in millimeters.

2. Unless specified, all connectors are type SMA female

field replaceable. SMA male also available, see

ordering options.

3. Tolerance as follows:

.xx = ±0.01 [.xx = ±0.25]

.xxx = ±0.005 [.xxx = ±0.13]

TTL CONTROL LOGIC

Non-inverting Logic 0 (low) (0 to 0.8 V) Insertion loss

Logic 1 (high) (2.4 to 4.7 V) Isolation

Inverting Logic 0 (low) (0 to 0.8 V) Isolation

Logic 1 (high) (2.4 to 4.7 V) Insertion loss

Non-inverting

SP1T Control Input Signal Path

E1 J1 – J2

Low l. loss

High Isolation

Inverting

Control Input Signal Path

E1 J1 – J2

Low Isolation

High l. loss

100 Davids Drive, Hauppauge, NY 11788 • TEL: (631) 436-7400 • FAX: (631) 436-7430 • www.miteq.com

SINGLE-POLE SINGLE-THROW SWITCHES

SP1T SWITCH ORDERING INFORMATION

To order a switch, please include the model number derived from the following table. If requesting a quotation for a switch not

listed in this catalog, please consult MITEQ. Include any additional specifications that are not listed.

SW 1 - 020 180 A N 1 N F

SWITCH

Number of throw(s)

Frequency (100’s of MHz)

Lower frequency

Upper frequency

Type

Absorptive............................................................................A

Reflective .............................................................................R

Logic

Non-inverting........................................................................N

Inverting ...............................................................................I

No driver ..............................................................................X(See Note 1)

Power Supply

+5 V, -12 V...........................................................................1

+5 V, -5 V.............................................................................2(See Note 2)

+5 V, -15 V...........................................................................3

+12 V, -12 V.........................................................................4

+15 V, -15 V.........................................................................5

No driver ..............................................................................X

Hermeticity

Non-hermetic ....................................................................... N

Hermetic............................................................................... H

Connectors

SMA-Female........................................................................ F

SMA-Male ............................................................................ M

Note 1: For “no driver” option, unit is current controlled through logic control pin, -20 mA for low loss condition and +20 mA for

isolation state. Switching speeds are not measured on driverless units.

Note 2: This option has 0.2 dB higher insertion loss, on/off time is 50 ns maximum and rise/fall time is 30 ns typical.

AVAILABLE OPTIONS

• Add suffix FS.............. Ultra-fast switching (SP1T Reflective only with power supply Option 1)

• Add suffix VL1............ Common port video filter

• Add suffix VL2............ Output port(s) video filter

• Add suffix VL3............ Both common port and output port(s) video filter

• Add suffix HP.............. Higher power (alternate package configurations)

Example:

The above illustrated part number SW1-020180AN1NF is for the following: Switch SP1T

2 to 18 GHz

Absorptive

Non-inverting

+5 V, -12 V

Non-hermetic

SMA-F connectors

Consult MITEQ for additional options.

When additional options are ordered, MITEQ will add a 4 digit number (-SXXXX) suffix to the part number.

100 Davids Drive, Hauppauge, NY 11788 • TEL: (631) 436-7400 • FAX: (631) 436-7430 • www.miteq.com