FTLF1323P1WTR - Finisar Corporation

F i n i s a r

 Finisar Corporation December 2, 2005 Rev.A Page 1

Product Specification

OC-3 IR-1/STM S-1.1 RoHS Compliant Pluggable SFP Transceiver

FTLF1323P1xTR

PRODUCT FEATURES

• Up to 155 Mb/s bi-directional

data links

• Hot-pluggable SFP footprint

• Built-in digital diagnostic functions

• Uncooled Fabry-Perot 1310nm

laser transmitter

• Duplex LC connector

• RoHS compliant and lead-free

• Metal enclosure, for lower EMI

• Single 3.3V power supply

• Low power dissipation <700mW

typical

• Industrial operating temperature

range: -40°C to 85°C

APPLICATIONS

• SONET OC-3 IR-1 / SDH STM S-1.1

• SONET OC-3 SR / SDH STM I-1

• Suitable for Fast Ethernet

Finisar’s FTLF1323P1xTR Small Form Factor Pluggable (SFP) transceivers are

compatible with the Small Form Factor Pluggable Multi-Sourcing Agreement (MSA)1.

They comply with SONET and SDH standards2 at OC-3 IR-1/STM S-1.1 and OC-3

SR/STM I-1, and are suitable for Fast Ethernet applications. Digital diagnostics

functions are available via the 2-wire serial bus specified in the SFP MSA. They are

RoHS compliant and lead-free per Directive 2002/95/EC3 and Finisar Application Note

AN-2038.

PRODUCT SELECTION

FTLF1323P1xTR

x W Wide Extraction Bail

B Narrow Extraction Bail

FTLF1323P1xTR Pluggable SFP Product Specification - December 2005 F i n i s a r

 Finisar Corporation December 2, 2005 Rev.A Page 2

I. Pin Descriptions

Pin Symbol Name/Description Ref.

1 VEET Transmitter Ground (Common with Receiver Ground) 1

2 TFAULT Transmitter Fault. Not supported.

3 TDIS Transmitter Disable. Laser output disabled on high or open. 2

4 MOD_DEF(2) Module Definition 2. Data line for Serial ID. 3

5 MOD_DEF(1) Module Definition 1. Clock line for Serial ID. 3

6 MOD_DEF(0) Module Definition 0. Grounded within the module. 3

7 Rate Select No connection required 4

8 LOS Loss of Signal indication. Logic 0 indicates normal operation. 5

9 VEER Receiver Ground (Common with Transmitter Ground) 1

10 VEER Receiver Ground (Common with Transmitter Ground) 1

11 VEER Receiver Ground (Common with Transmitter Ground) 1

12 RD- Receiver Inverted DATA out. AC Coupled.

13 RD+ Receiver Non-inverted DATA out. AC Coupled.

14 VEER Receiver Ground (Common with Transmitter Ground) 1

15 VCCR Receiver Power Supply

16 VCCT Transmitter Power Supply

17 VEET Transmitter Ground (Common with Receiver Ground) 1

18 TD+ Transmitter Non-Inverted DATA in. AC Coupled.

19 TD- Transmitter Inverted DATA in. AC Coupled.

20 VEET Transmitter Ground (Common with Receiver Ground) 1

Notes:

1. Circuit ground is internally isolated from chassis ground.

2. Laser output disabled on TDIS >2.0V or open, enabled on TDIS <0.8V.

3. Should be pulled up with 4.7k - 10kohms on host board to a voltage between 2.0V and 3.5V.

MOD_DEF(0) pulls line low to indicate module is plugged in.

4. Finisar FTLF1323P1xTR transceivers operate between OC-3 and 125 Mbit/s without active control.

5. LOS is open collector output. Should be pulled up with 4.7k - 10kohms on host board to a voltage

between 2.0V and 3.5V. Logic 0 indicates normal operation; logic 1 indicates loss of signal.

VeeT

VeeR

TD-

TD+

RD+

RD-

VccT

VccR

VeeT

VeeR

TXFault

MOD-DEF(2)

MOD-DEF(1)

MOD-DEF(0)

Rate Select

LOS

Towards

ASIC

Towards

Bezel

TX Disable

VeeR

Pinout of Connector Block on Host Board

FTLF1323P1xTR Pluggable SFP Product Specification - December 2005 F i n i s a r

 Finisar Corporation December 2, 2005 Rev.A Page 3

II. Absolute Maximum Ratings

Parameter Symbol Min Typ Max Unit Ref.

Maximum Supply Voltage Vcc -0.5 4.5 V

Storage Temperature TS -40 100

°C

Case Operating Temperature TOP -40 85

°C

Relative Humidity RH 0 85 % 1

III. Electrical Characteristics (TOP = -40 to 85 °

°°

°C, VCC = 3.10 to 3.50 Volts)

Parameter Symbol Min Typ Max Unit Ref.

Supply Voltage Vcc 3.10 3.50 V

Supply Current Icc 165 300 mA

Transmitter

Input differential impedance Rin 100 Ω 2

Single ended data input swing Vin,pp 250 1200 mV

Transmit Disable Voltage VD Vcc – 1.3 Vcc V

Transmit Enable Voltage VEN Vee Vee+ 0.8 V 3

Transmit Disable Assert Time 10

µs

Receiver

Single ended data output swing Vout,pp 300 400 800 mV 4

Data rise/fall time tr 250 500 ps 5

LOS Fault VLOS fault Vcc – 0.5 VccHOST V 6

LOS Normal VLOS norm Vee Vee+0.5 V 6

Power Supply Rejection PSR 100 mVpp 7

Notes:

1. Non condensing

2. AC coupled.

3. Or open circuit.

4. Into 100 ohm differential termination.

5. 20 – 80 %

6. Loss Of Signal is LVTTL. Logic 0 indicates normal operation; logic 1 indicates no signal detected.

7. All transceiver specifications are compliant with a power supply sinusoidal modulation of 20 Hz to 1.5

MHz up to specified value applied through the power supply filtering network shown on page 23 of the

Small Form-factor Pluggable (SFP) Transceiver MultiSource Agreement (MSA), September 14, 2000.

FTLF1323P1xTR Pluggable SFP Product Specification - December 2005 F i n i s a r

 Finisar Corporation December 2, 2005 Rev.A Page 4

IV. Optical Characteristics (TOP = -40 to 85 °

°°

°C, VCC = 3.10 to 3.50 Volts)

Parameter Symbol Min Typ Max Unit Ref.

Transmitter

Output Opt. Pwr: 9/125 SMF POUT -15 -8 dBm 1

Optical Wavelength λ 1261 1360 nm

Spectral Width σ 7.7 nm

Optical Extinction Ratio ER 8.2 dB

Optical Rise/Fall Time tr/ tf 500 ps 2

Relative Intensity Noise RIN -120 dB/Hz

Generated Jitter (peak to peak) JTXp-p 0.07 UI 3

Generated Jitter (rms) JTXrms 0.007 UI 3

Mask Margin 20%

Receiver

Average Rx Sensitivity @ OC-3 RSENS1 -28 -8 dBm 4

Average Rx Sensitivity @ 125 Mb/s RSEN2 -28 -8 dBm 4

Optical Center Wavelength λC 1260 1600 nm

LOS De-Assert LOSD -28 dBm

LOS Assert LOSA -45 dBm

LOS Hysteresis 0.5 dB

Notes:

1. Class 1 Laser Safety per FDA/CDRH and EN (IEC) 60825 regulations.

2. Unfiltered, 20-80%

3. Jitter measurements taken using Agilent OMNIBERT 718 in accordance with GR-253.

4. With worst-case extinction ratio. Measured with a PRBS 223-1 test pattern.

FTLF1323P1xTR Pluggable SFP Product Specification - December 2005 F i n i s a r

 Finisar Corporation December 2, 2005 Rev.A Page 5

V. General Specifications

Parameter Symbol Min Typ Max Units Ref.

Data Rate BR 125 155 Mb/sec 1

Bit Error Rate BER 10-12 2

Max. Supported Link Length on

9/125µm SMF @ OC-3

LMAX5 15 km 4

Notes:

1. Compliant with SONET and SDH at the following rates: OC-3 IR-1/STM S-1.1 and

OC-3 SR/STM I-1.

2. Tested with a PRBS 223-1 test pattern.

3. Attenuation of 0.55 dB/km is used for the link length calculations (per GR-253 CORE). Distances are

indicative only. Please refer to the Optical Specifications in Table IV to calculate a more accurate link

budget based on specific conditions in your application.

VI. Environmental Specifications

Finisar 1310nm SFP transceivers have an industrial operating temperature range from

–40°C to +85°C case temperature.

Parameter Symbol Min Typ Max Units Ref.

Case Operating Temperature Top -40 85 °C

Storage Temperature Tsto -40 100 °C

VII. Regulatory Compliance

Finisar transceivers are Class 1 Laser Products and comply with US FDA regulations.

These products are certified by TÜV and CSA to meet the Class 1 eye safety

requirements of EN (IEC) 60825 and the electrical safety requirements of

EN (IEC) 60950. Copies of certificates are available at Finisar Corporation upon request.

FTLF1323P1xTR Pluggable SFP Product Specification - December 2005 F i n i s a r

 Finisar Corporation December 2, 2005 Rev.A Page 6

VIII. Digital Diagnostic Functions

Finisar FTLF1323P1xTR SFP transceivers support the 2-wire serial communication

protocol as defined in the SFP MSA1. It is very closely related to the E2PROM defined in

the GBIC standard, with the same electrical specifications.

The standard SFP serial ID provides access to identification information that describes

the transceiver’s capabilities, standard interfaces, manufacturer, and other information.

Additionally, Finisar SFP transceivers provide a unique enhanced digital diagnostic

monitoring interface, which allows real-time access to device operating parameters such

as transceiver temperature, laser bias current, transmitted optical power, received optical

power and transceiver supply voltage. It also defines a sophisticated system of alarm and

warning flags, which alerts end-users when particular operating parameters are outside of

a factory-set normal range.

The SFP MSA defines a 256-byte memory map in E2PROM that is accessible over a

2-wire serial interface at the 8 bit address 1010000X (A0h). The digital diagnostic

monitoring interface makes use of the 8 bit address 1010001X (A2h), so the originally

defined serial ID memory map remains unchanged. The interface is identical to, and is

thus fully backward compatible with both the GBIC Specification and the SFP Multi

Source Agreement. The complete interface is described in Finisar Application Note

AN-2030: “Digital Diagnostics Monitoring Interface for SFP Optical Transceivers”.

The operating and diagnostics information is monitored and reported by a Digital

Diagnostics Transceiver Controller (DDTC) inside the transceiver, which is accessed

through a 2-wire serial interface. When the serial protocol is activated, the serial clock

signal (SCL, Mod Def 1) is generated by the host. The positive edge clocks data into the

SFP transceiver into those segments of the E2PROM that are not write-protected. The

negative edge clocks data from the SFP transceiver. The serial data signal (SDA, Mod

Def 2) is bi-directional for serial data transfer. The host uses SDA in conjunction with

SCL to mark the start and end of serial protocol activation. The memories are organized

as a series of 8-bit data words that can be addressed individually or sequentially.

For more information, please see the SFP MSA documentation1 or Finisar Application

Note AN-2030.

Digital diagnostics for the FTLF1323P1xTR are externally calibrated by default.

Please note that evaluation board FDB-1018 is available with Finisar ModDEMO

software that allows simple to use communication over the 2-wire serial interface.

FTLF1323P1xTR Pluggable SFP Product Specification - December 2005 F i n i s a r

 Finisar Corporation December 2, 2005 Rev.A Page 7

IX. Mechanical Specifications

Finisar’s Small Form Factor Pluggable (SFP) transceivers are compatible with the

dimensions defined by the SFP Multi-Sourcing Agreement (MSA) 3.

FTLF1323P1BTR

FTLF1323P1xTR Pluggable SFP Product Specification - December 2005 F i n i s a r

 Finisar Corporation December 2, 2005 Rev.A Page 8

FTLF1323P1WTR

FTLF1323P1xTR Pluggable SFP Product Specification - December 2005 F i n i s a r

 Finisar Corporation December 2, 2005 Rev.A Page 9

X. PCB Layout and Bezel Recommendations

FTLF1323P1xTR Pluggable SFP Product Specification - December 2005 F i n i s a r

 Finisar Corporation December 2, 2005 Rev.A Page 10

FTLF1323P1xTR Pluggable SFP Product Specification - December 2005 F i n i s a r

 Finisar Corporation December 2, 2005 Rev.A Page 11

XI. References

1. Small Form Factor Pluggable (SFP) Transceiver Multi-Source Agreement (MSA),

September 2000. Documentation is currently available at Finisar upon request.

2. Bellcore GR-253 and ITU-T G.957 Specifications.

3. Directive 2002/95/EC of the European Council Parliament and of the Council,

“on the restriction of the use of certain hazardous substances in electrical and

electronic equipment.” January 27, 2003.

XII. For More Information

Finisar Corporation

1389 Moffett Park Drive

Sunnyvale, CA 94089-1133

Tel. 1-408-548-1000

Fax 1-408-541-6138

sales@finisar.com