http://www.tracopower.com Page 1 of 3
DC/DC Converters
TES 2N Series, 2 Watt
Features
◆ Low profile SMD-package
◆ Wide 2:1 input voltage range
◆ I/O isolation 1500 VDC
◆ Input filter meets EN55022, class A
◆ Operating temperature range
–40°C to +85°C
◆ Short-circuit protection
◆ Qualified for leadfree reflow solder
process according IPC J-STD-020D.1
◆ Available in tape and reel package
◆ Bears washing process
◆ 3-year product warranty
Ordercode Input voltage range Output voltage Output current max. Efficiency typ.
TES 2N-0510 3.3 VDC 500 mA 70 %
TES 2N-0511 5 VDC 400 mA 73 %
TES 2N-0512 4.5 – 9.0 VDC 12VDC 165 mA 75 %
TES 2N-0513 (nominal 5 VDC) 15 VDC 135 mA 73 %
TES 2N-0521 ± 5 VDC ±200 mA 64 %
TES 2N-0522 ±12 VDC ±85 mA 69 %
TES 2N-0523 ±15 VDC ±65 mA 71 %
TES 2N-1210 3.3 VDC 500 mA 73 %
TES 2N-1211 5 VDC 400 mA 77 %
TES 2N-1212 9 – 18 VDC 12 VDC 165 mA 80 %
TES 2N-1213 (nominal 12 VDC) 15 VDC 135 mA 80 %
TES 2N-1221 ±5 VDC ±200 mA 73 %
TES 2N-1222 ±12 VDC ±85 mA 78 %
TES 2N-1223 ±15 VDC ±65 mA 78 %
TES 2N-2410 3.3 VDC 500 mA 72 %
TES 2N-2411 5 VDC 400 mA 77 %
TES 2N-2412 18 – 36 VDC 12 VDC 165 mA 80 %
TES 2N-2413 (nominal 24 VDC) 15 VDC 135 mA 81 %
TES 2N-2421 ±5 VDC ±200 mA 74 %
TES 2N-2422 ±12 VDC ±85 mA 78 %
TES 2N-2423 ±15 VDC ±65 mA 80 %
TES 2N-4810 3.3 VDC 500 mA 71 %
TES 2N-4811 5 VDC 400 mA 73 %
TES 2N-4812 36 – 75 VDC 12 VDC 165 mA 79 %
TES 2N-4813 (nominal 48 VDC) 15 VDC 135 mA 79 %
TES 2N-4821 ± 5 VDC ±200 mA 71 %
TES 2N-4822 ±12 VDC ±85 mA 77 %
TES 2N-4823 ±15 VDC ±65 mA 77 %
Models
The TES-2N series is a family of high performance 2W DC/DC converter modules
featuring wide 2:1 input voltage ranges. The 28 models come in a low profile SMD
package which requires just 3 cm2 space on the PCB. A high efficiency allows an
operating temperature range of –40°C to +85°C. A built-in EMI input filter complies
with EN 55022, class A. Typical applications for these converters are battery ope-
rated equipment, instrumentation, communication and industrial electronics, every-
where where isolated, tightly regulated voltages are required.
UL 60950-
1
CB
Scheme
http://www.tracopower.com Page 2 of 3
All specifications valid at nominal input voltage, full load and +25°C after warm-up time unless otherwise stated.
DC/DC Converters
TES 2N Series 2 Watt
Input Specifications
Input current at full load (nominal input) 5 Vin models: 600 mA typ.
12 Vin models: 220 mA typ.
24 Vin models: 110 mA typ.
48 Vin models: 55 mA typ.
Start-up voltage / under voltage shut down 5 Vin models: 4.5 VDC / 4.0 VDC typ. (or lower)
12 Vin models: 9.0 VDC / 8.5 VDC typ. (or lower)
24 Vin models: 18 VDC / 17 VDC typ.
48 Vin models: 36 VDC / 34 VDC typ.
Surge voltage (100 msec. max.) 5 Vin models: 11 V max.
12 Vin models: 25 V max.
24 Vin models: 50 V max.
48 Vin models: 100 V max.
Conducted noise (input) EN 55022 level A, FCC part 15, level A
Input fuse recommended, required for compliance with CB
– recommended min. fuse rating 5 V models: 500 mA
12 V models: 200 mA
Output Specifications
Voltage set accuracy ±2 %
Regulation – Input variation Vin min. to Vin max. 0.5 % max.
– Load variation 25 – 100 % 0.75 % max.
dual output models: 2.0 % (balanced load)
Ripple and noise (20 MHz Bandwidth) 50 mVpk-pk max.
Transient response (25 % load step change)
– Recovery time 300 µs typ.
– Deviation ±5 %
Temperature coefficient ±0.02 %/K
Short circuit protection indefinite, automatic recovery
Minimum load 25 % of rated max current (operation at lower
load condition is safe but a higher output ripple
will be experienced)
Capacitive load 3.3 VDC output models: 2200 µF max.
5 VDC output models: 1000 µF max.
12 VDC output models: 170 µF max.
15 VDC output models: 110 µF max.
±5 VDC output models: 470 µF max.
±12 VDC output models: 100 µF max.
±15 VDC output models: 47 µF max.
General Specifications
Temperature ranges – Operating –40°C to +85°C
– Case temperatures +90°C
– Storage –50°C to +125°C
Derating 3.5 %/K above +71°C
Humidity (non condensing) 95 % rel. H max.
Reliability, calculated MTBF ( M I L- H D B K-217F, at +25°C, ground benign) >1.0 Mio h
Isolation voltage (60sec.) – Input/Output 1500 VDC
Isolation capacitance – Input/Output 250 pF
Isolation resistance – Input/Output (500 VDC) >1000 M Ohm
Switching frequency 300 kHz (PFM)
Specifications can be changed without notice! Make sure you are using the latest documentation, downloadable at www.tracopower.com
www.tracopower.com
Page 3 of 3
Rev. July 11, 2018
DC/DC Converters
TES 2N Series 2 Watt
Outline Dimensions
Pin Single Dual
1–Vin (GND) –Vin (GND)
7No con. No con.
8No con. Common
9+Vout +Vout
10 –Vout –Vout
16 +Vin +Vin
Pin-Out
General Specifications
Safety approvals UL 60950-1, IEC/EN 60950-1
– Certification documents www.tracopower.com/overview/tes2n
Environmental compliance – Reach www.tracopower.com/products/reach-declaration.pdf
– RoHS RoHS directive 2011/65/EU
Physical Specifications
Casing material DAP (UL94V-0 rated)
Pin material Phosphor bronze
Weight 5.1 g ( 0.17oz )
Moisture sensivity level (MSL) level 2 as per J-STD-020D.1 (to find at:
www.jedec.org - free registration required)
Soldering temperature max. 260°C / 10 sec.
24.0
(0.94)
0.25
(0.01)
9.0
(0.35)
18.1
(0.71)
13.7
(0.54)
15.24
(0.60)
2.54
(0.10)
3.11
(0.12)
top view
178
16 10 9
0 - 4°
0.15
1.0
(0.04)
10.6
(0.42)
9.4
(0.37)
Ø1.5
(Ø 0.06) vent hole with membrane on bottom side
(to allow proper washing process)
2.8
(0.11)
13.7 (0.54)
15.24 (0.60) 2.54 (0.10)3.11 (0.12)
1.4 (0.055) min.
2.8
(0.11)
Dimensions in [mm], () = Inch
Tolerances ±0.25 (±0.01)
Pin pitch tolerances ±0.05 (±0.002)
Solder Pad Dimension
Supporting documents: www.tracopower.com/overview/tes2n
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
TRACO Power:
TES 2N-0510 TES 2N-0522 TES 2N-1211 TES 2N-2413 TES 2N-2421 TES 2N-2412 TES 2N-2411 TES 2N-2410
TES 2N-0521 TES 2N-1212 TES 2N-0511 TES 2N-1210 TES 2N-1221 TES 2N-2422 TES 2N-1213 TES 2N-1222
TES 2N-4822 TES 2N-2423 TES 2N-4821 TES 2N-0513 TES 2N-4813 TES 2N-4811 TES 2N-0523 TES 2N-4810
TES 2N-1223 TES 2N-0512 TES 2N-4823 TES 2N-4812
