T18 Sensors - DC Voltage Series Self-contained, dc-operated sensors Additional information on this product is immediately available online at www.bannerengineering.com/116163 View or download additional information, including excess gain curves, beam patterns and accessories. For further assistance, contact a Banner Engineering Applications Engineer at (763) 544-3164 or (888) 373-6767. Sensing Mode Range Opposed LED 20 m (66') Infrared 950 nm Retro-reflective with Gain control 2 m (79") Polarized Retroreflective P Cabled Emitters bn Diffuse with Gain control + bu - 10-30V dc bn + bu - Fixed Field 10-30V dc No Connection NPN (Sinking) Outputs Standard Hookup bu bn bk wh - 10 - 30V dc + Load Alarm PNP (Sourcing) Outputs Standard Hookup + - 10 - 30V dc Load Load PNP T18SP6R NPN T18SN6L PNP T18SP6L NPN T18SN6LP PNP T18SP6LP NPN T18SN6D PNP T18SP6D NPN T18SN6FF25 PNP T18SP6FF25 NPN T18SN6FF50 PNP T18SP6FF50 NPN T18SN6FF100 PNP T18SP6FF100 QD Models M18 x 1 Thread o 15 mm (0.59") o 30.0 mm (1.18") o 30.0 mm (1.18") Green LED Power Indicator Yellow LED Output Indicator 41.5 mm (1.64") Single-turn Sensitivity (Gain) Control (D and L Models) 53.7 mm (2.11") 11.5 mm (0.45") Alarm Hookup WARNING . . . Not To Be Used for Personnel Protection + - 10 - 30V dc Load Alarm NOTE: QD hookups are functionally identical. Printed in USA T18SN6R Jam Nut (Supplied) 30.0 mm (1.18") bu bn bk wh NPN Use polarized models when shiny objects will be sensed. Cabled Models - 10 - 30V dc + bn bu bk wh T186E Dimensions Alarm Hookup bu bk wh - * Standard 2 m (6.5') cable models are listed. * 9 m (30') cable: add suffix "W/30" (e.g., T186E W/30). * 4 -pin Euro-style QD models: add suffix "Q" (e.g., T186EQ). A model with a QD connector requires a mating cable. Load Load bn 50 mm (2") cutoff Infrared 880 nm 100 mm (4") cutoff bk wh 500 mm (20") 25 mm (1") cutoff QD Emitters Visible Red 680 nm Output Model* Never use these products for personnel protection. Doing so could lead to serious injury or death. These devices do NOT include the self-checking redundant circuitry necessary to allow their use in personnel safety applications. A device failure or malfunction can cause either an energized or de-energized output condition. Consult your current Banner Safety Products catalog for safety products that meet OSHA, ANSI, and IEC standards for personnel protection. Jan 2013 P/N 116163 Rev. B T18 Sensors - DC-Voltage Series Specifications Supply Voltage and Current (exclusive of load current). 10 to 30V dc (10% max ripple) Supply current (exclusive of load current): Emitters, Non-Polarized Retro, Diffuse: 25 mA Receivers: 20 mA Polarized Retroreflective: 30 mA Fixed-Field: 35 mA Repeatability Opposed mode: 375 s Retro, Fixed-Field and Diffuse: 750 s Repeatability and response are independent of signal strength. Adjustments Non-polarized retro and diffuse models (only) have a single-turn rear-panel sensitivity control (turn clockwise to increase gain). Supply Protection Circuitry. Protected against reverse polarity and transient voltages Output Configuration SPDT solid-state dc switch; Choose NPN (current sinking) or PNP (current sourcing) models Light Operate: N.O. output conducts when sensor sees its own (or the emitter's) modulated light Dark Operate: N .C. output conducts when the sensor sees dark; the N.C. (normally closed) output may be wired as a normally open marginal signal alarm output, depending upon hookup to power supply (U.S. patent 5087838) Output Rating 150 mA maximum (each) in standard hookup. When wired for alarm output, the total load may not exceed 150 mA. OFF-state leakage current: < 1 microamp @ 30V dc ON-state saturation voltage: < 1V at 10 mA dc; < 1.5V at 150 mA dc Output Protection Circuitry Protected against false pulse on power-up and continuous overload or short circuit of outputs Indicators Two LEDs (Green and Yellow) Green ON steady: power to sensor is ON Green flashing: output is overloaded Yellow ON steady: N.O. output is conducting Yellow flashing: excess gain marginal (1 to 1.5x) in light condition Construction PBT polyester housing; polycarbonate (opposed mode) or acrylic lens Environmental Rating Leakproof design rated NEMA 6P, DIN 40050 (IP69K) Connections 2 m (6.5') or 9 m (30') attached cable, or 4-pin Euro-style quick-disconnect fitting Operating Conditions Temperature: -40 to +70C (-40 to +158F) Maximum relative humidity: 90% at 50C (non-condensing) Vibration and Mechanical Shock All models meet Mil. Std. 202F requirements. Method 201A (Vibration; frequency 10 to 60 Hz, max., double amplitude 0.06" acceleration 10G). Method 213B conditions H&I (Shock: 75G with unit operating; 100G for non-operation) Output Response Time Opposed mode: 3 ms ON, 1.5 ms OFF Retro, Fixed-Field and Diffuse: 3 ms ON and OFF NOTE: 100 ms delay on power-up; outputs do not conduct during this time. Certifications Quick-Disconnect (QD) Cables Style Model Length 4-pin Euro-style Straight MQDC-406 MQDC-415 MQDC-430 2 m (6.5') 5 m (15') 9 m (30') Dimensions Pin-Out o 15 mm (0.6") 44 mm max. (1.7") M12 x 1 White Wire Brown Wire Blue Wire Black Wire 38 mm max. (1.5") 4-pin Euro-style Right-angle MQDC-406RA MQDC-415RA MQDC-430RA 2 m (6.5') 5 m (15') 9 m (30') 38 mm max. (1.5") M12 x 1 o 15 mm (0.6") Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty period. This warranty does not cover damage or liability for misuse, abuse, or the improper application of the Banner product. THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE OF DEALING OR TRADE USAGE. This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING CORP. BE LIABLE TO BUYER OR ANY OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY PRODUCT DEFECT OR FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE. Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligations or liabilities relating to any product previously manufactured by Banner Engineering Corp. P/N 116163 Rev. B Banner Engineering Corp., 9714 Tenth Ave. No., Minneapolis, MN USA 55441 * Phone: 763.544.3164 * www.bannerengineering.com * Email: sensors@bannerengineering.com