Version History / Current Downloads for ___________________ Preface the SIMATIC NET S7-CPs PROFIBUS 1 ___________________ SIMATIC S7-300 2 ___________________ SIMATIC S7-400 Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS Reference Manual 07.2013 C79000-G8976-C174-22 Legal information Warning notice system This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are graded according to the degree of danger. DANGER indicates that death or severe personal injury will result if proper precautions are not taken. WARNING indicates that death or severe personal injury may result if proper precautions are not taken. CAUTION indicates that minor personal injury can result if proper precautions are not taken. NOTICE indicates that property damage can result if proper precautions are not taken. If more than one degree of danger is present, the warning notice representing the highest degree of danger will be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to property damage. Qualified Personnel The product/system described in this documentation may be operated only by personnel qualified for the specific task in accordance with the relevant documentation, in particular its warning notices and safety instructions. Qualified personnel are those who, based on their training and experience, are capable of identifying risks and avoiding potential hazards when working with these products/systems. Proper use of Siemens products Note the following: WARNING Siemens products may only be used for the applications described in the catalog and in the relevant technical documentation. If products and components from other manufacturers are used, these must be recommended or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and maintenance are required to ensure that the products operate safely and without any problems. The permissible ambient conditions must be complied with. The information in the relevant documentation must be observed. Trademarks All names identified by (R) are registered trademarks of Siemens AG. The remaining trademarks in this publication may be trademarks whose use by third parties for their own purposes could violate the rights of the owner. Disclaimer of Liability We have reviewed the contents of this publication to ensure consistency with the hardware and software described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the information in this publication is reviewed regularly and any necessary corrections are included in subsequent editions. Siemens AG Industry Sector Postfach 48 48 90026 NURNBERG GERMANY Order number: C79000-G8976-C174 07/2013 Technical data subject to change Copyright (c) Siemens AG 2008 - 2013. All rights reserved Preface Overview Information on this document This document provides you with information on the current products and on products that were previously available along with their versions and a brief description of the product. CP documentation You will find the documentation for the SIMATIC NET S7 CP here: Depending on the shipment package, on the manual DVD supplied with the device or the product CD / product DVD On the pages of Product Support on the Internet (http://support.automation.siemens.com/ww/view/en/10805878) Go to the required product group and make the following settings: "Entry list" tab, Entry type "Manuals" Structure of the documentation There is a table for each module that informs you of the current version of the module and a second table that lists the previously available versions. Layout of the tables / example: Device data Order numbers / versions Characteristics STEP 7 version required (for full functionality) Order number: Extended functionality compared with the previous hardware product version: * 6GK7... Hardware product version: X STEP 7 Vx.y ... Firmware version: Y Relevant documentation Manual .... Entry ID: 123456 http://www... Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS Reference Manual, 07.2013, C79000-G8976-C174-22 3 Preface Notes for the reader The meaning of the table columns is as follows: "Order numbers / versions" column The column contains the following information: - Current hardware product version and current firmware version. If a firmware update is available, the download address is shown. - Download address of the documentation and "SIMATIC NET Updates" entries. The numeric string is the relevant entry ID. "Characteristics / new or modified functions" column Here, you will find an overview of the following: - The essential performance characteristics of new modules; - For modified modules, the changed characteristics or bugs fixed. "STEP 7 version required (for full functionality)" column The STEP 7 version required for configuration. This is the STEP 7 version as of which all performance characteristics of the module version described can be used. The very latest documentation is available on the Internet! The latest descriptions of the current products are always available on the Internet under the entry IDs or on the Internet pages listed here and in the tables following. Manuals on the STEP 7 configuration tool can be found under the following entry IDs: Configuring and commissioning S7 CPs for PROFIBUS 1158693 (http://support.automation.siemens.com/ww/view/en/1158693) Functions (FC) and Function Blocks (FB) for SIMATIC NET S7 CPs 30564821 (http://support.automation.siemens.com/ww/view/de/30564821) Downloads of the current versions of the program blocks For new user programs, always use the current program block versions. You will find information on the current program block versions and can download the current SIMATIC NET program blocks from the Internet under the following Entry ID: 8797900 (http://support.automation.siemens.com/WW/view/de/8797900) If you are replacing a CP, please follow the instructions in the relevant manual (refer to "Further information"). Current version history You will find the latest version history for S7 CPs as well as this version history for SIMATIC NET blocks under the following Entry ID: 9836605 (http://support.automation.siemens.com/WW/view/de/9836605) Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS 4 Reference Manual, 07.2013, C79000-G8976-C174-22 Preface Further information If you require descriptions of the older versions, please contact your Siemens representative quoting the relevant product name. Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS Reference Manual, 07.2013, C79000-G8976-C174-22 5 Preface Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS 6 Reference Manual, 07.2013, C79000-G8976-C174-22 Table of contents Preface ...................................................................................................................................................... 3 1 2 SIMATIC S7-300........................................................................................................................................ 9 1.1 1.1.1 1.1.2 1.1.3 CP 342-5 / CP 342-5 FO................................................................................................................9 Current version CP 342-5 ..............................................................................................................9 Current version CP 342-5 FO ......................................................................................................10 Predecessor modules / predecessor versions.............................................................................11 1.2 1.2.1 1.2.2 1.2.3 CP 343-5 ......................................................................................................................................21 Current version.............................................................................................................................21 Previous versions.........................................................................................................................22 Predecessor modules ..................................................................................................................26 SIMATIC S7-400...................................................................................................................................... 27 2.1 2.1.1 2.1.2 2.1.3 CP 443-5 Basic ............................................................................................................................27 Current version.............................................................................................................................27 Previous versions.........................................................................................................................28 Predecessor modules ..................................................................................................................29 2.2 2.2.1 2.2.2 2.2.3 CP 443-5 Extended......................................................................................................................32 Current version.............................................................................................................................32 Previous versions.........................................................................................................................33 Predecessor modules ..................................................................................................................34 Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS Reference Manual, 07.2013, C79000-G8976-C174-22 7 Table of contents Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS 8 Reference Manual, 07.2013, C79000-G8976-C174-22 1 SIMATIC S7-300 1.1 CP 342-5 / CP 342-5 FO 1.1.1 Current version CP 342-5 Characteristic data of the device Required STEP 7 Version (for Order numbers / versions Features / new or modified functions full functionality) Order number: Hardware modification: STEP 7 6GK7 342-5DA03-0XE0 * Due to production, no functional modifications compared with the previous version. The firmware version is unchanged and therefore compatible and can be used with hardware product versions 1 and 2 * Hardware product version: 2 Firmware version: V6.0 The GSD file can be obtained at: 113652 (http://support.automation.siemens.com /ww/view/de/113652) STEP 7 as of version V5.5 SP2 STEP 7 as of version V5.4 SP5 with HSP 1049 STEP 7 Professional * * STEP 7 V11.0 Relevant documentation: S7 CPs for PROFIBUS manual * General section: as of release 05 - 09/2011 1158693 (http://support.automation.siemens.com /ww/view/en/1158693) * Part specific to the CP 342-5 / CP 342-5 FO as of release 09 - 10/2011 8773570 (http://support.automation.siemens.com /ww/view/de/8773570) Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS Reference Manual, 07.2013, C79000-G8976-C174-22 9 SIMATIC S7-300 1.1 CP 342-5 / CP 342-5 FO 1.1.2 Current version CP 342-5 FO Characteristic data of the device Required STEP 7 Version (for Order numbers / versions Features / new or modified functions full functionality) Order number: Firmware modification: STEP 7 6GK7 342-5DF00-0XE0 * * STEP 7 Version V5.1 SP2 or higher Bugs fixed, no functional modifications compared with the You configure the CP as firmware previous firmware version. Firmware version: V5.7 version V5.0. The firmware version is compatible and The firmware can be obtained at: STEP 7 Professional can be used with hardware product 24105718 * STEP 7 Professional Version V11.0 versions 1, 3 and 4, 5, 6 (http://support.automation.siemens.com or higher /ww/view/de/24105718) You configure the CP as firmware The GSD file can be obtained at: version V5.0. 113652 Hardware product version: 5 (http://support.automation.siemens.com /ww/view/de/113652) Relevant documentation: S7 CPs for PROFIBUS manual as of Release 04 - 02/2003 * General section: 1158693 (http://support.automation.siemens.com /ww/view/en/1158693) Part specific to the CP 342-5 / CP 342-5 FO 8773570 (http://support.automation.siemens.com /ww/view/de/8773570) * SIMATIC NET updates with firmware release: 24104930 (http://support.automation.siemens.com /ww/view/de/24104930) Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS 10 Reference Manual, 07.2013, C79000-G8976-C174-22 SIMATIC S7-300 1.1 CP 342-5 / CP 342-5 FO 1.1.3 Predecessor modules / predecessor versions Characteristic data of the device Required STEP 7 Version (for Order numbers / versions Features / new or modified functions full functionality) Order number: The CP 342-5 (6GK7 342-5DA030XE0) is suitable as a replacement for the following predecessor products: STEP 7 6GK7 342-5DA03-0XE0 Hardware product version: 1 * STEP 7 as of version V5.5 SP2 STEP 7 as of version V5.4 SP5 with HSP 1049 * CP 342-5 (6GK7 342-5DA01-0XE0) The GSD file can be obtained at: STEP 7 Professional * CP 342-5 (6GK7 342-5DA02-0XE0) * STEP 7 V11.0 113652 (http://support.automation.siemens.com Additional functional characteristics: /ww/view/de/113652) * The CP supports SYNC / FREEZE Relevant documentation: in DP slave mode. S7 CPs for PROFIBUS manual Please refer to the information on compatibility in the current manual. * General section: Firmware version: V6.0 * CP 342-5 (6GK7 342-5DA00-0XE0) * as of release 05 - 09/2011 1158693 (http://support.automation.siemens.com /ww/view/en/1158693) * Part specific to the CP 342-5 / CP 342-5 FO as of release 09 - 10/2011 8773570 (http://support.automation.siemens.com /ww/view/de/8773570) SIMATIC NET updates with hardware release: 24104930 (http://support.automation.siemens.com /ww/view/de/24104930) Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS Reference Manual, 07.2013, C79000-G8976-C174-22 11 SIMATIC S7-300 1.1 CP 342-5 / CP 342-5 FO Characteristic data of the device Required STEP 7 Version (for Order numbers / versions Features / new or modified functions full functionality) Order number: Firmware modification: STEP 7 6GK7 342-5DA02-0XE0 * * STEP 7 Version V5.1 SP2 or higher Bugs fixed, no functional modifications compared with the You configure the CP as firmware previous firmware version. Firmware version: V5.7 version V5.0. The firmware version is compatible and The firmware can be obtained at: STEP 7 Professional can be used with hardware product 24105718 * STEP 7 Professional Version V11.0 versions 1, 3 and 4, 5, 6 (http://support.automation.siemens.com or higher /ww/view/de/24105718) You configure the CP as firmware The GSD file can be obtained at: version V5.0. 113652 Hardware product version: 6 (http://support.automation.siemens.com /ww/view/de/113652) Relevant documentation: S7 CPs for PROFIBUS manual as of Release 04 - 02/2003 * General section: 1158693 (http://support.automation.siemens.com /ww/view/en/1158693) Part specific to the CP 342-5 / CP 342-5 FO 8773570 (http://support.automation.siemens.com /ww/view/de/8773570) * SIMATIC NET updates with firmware release: 24104930 (http://support.automation.siemens.com /ww/view/de/24104930) Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS 12 Reference Manual, 07.2013, C79000-G8976-C174-22 SIMATIC S7-300 1.1 CP 342-5 / CP 342-5 FO Characteristic data of the device Order numbers / versions Features / new or modified functions Order number: Hardware modification: 6GK7 342-5DA02-0XE0 * Hardware product version: 6 6GK7 342-5DF00-0XE0 Hardware product version: 5 Firmware version: V5.6 Bugs fixed, no functional modifications compared with the previous version. The firmware version is unchanged and therefore compatible and can be used with hardware product versions 1, 3 and 4, 5, 6 Required STEP 7 Version (for full functionality) STEP 7 Version V5.1 SP2 or higher can be configured as firmware version V5.0 The GSD file can be obtained at: 113652 (http://support.automation.siemens.com /ww/view/de/113652) Relevant documentation: S7 CPs for PROFIBUS manual as of Release 04 - 02/2003 * General section: 1158693 (http://support.automation.siemens.com /ww/view/de/1158693) Part specific to the CP 342-5 / CP 342-5 FO 8773570 (http://support.automation.siemens.com /ww/view/de/8773570) * Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS Reference Manual, 07.2013, C79000-G8976-C174-22 13 SIMATIC S7-300 1.1 CP 342-5 / CP 342-5 FO Characteristic data of the device Order numbers / versions Features / new or modified functions Order number: Firmware modification: 6GK7 342-5DA02-0XE0 * Hardware product version: 5 6GK7 342-5DF00-0XE0 Hardware product version: 4 Bugs fixed, no functional modifications compared with the previous version. The firmware version is compatible and can be used with hardware product versions 1, 3 and 4, 5 Required STEP 7 Version (for full functionality) STEP 7 Version V5.1 SP2 or higher can be configured as firmware version V5.0 Firmware version: V5.6 The GSD file can be obtained at: 113652 (http://support.automation.siemens.com /ww/view/de/113652) Relevant documentation: S7 CPs for PROFIBUS manual as of Release 04 - 02/2003 * General section: 1158693 (http://support.automation.siemens.com /ww/view/de/1158693) Part specific to the CP 342-5 / CP 342-5 FO 8773570 (http://support.automation.siemens.com /ww/view/de/8773570) * Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS 14 Reference Manual, 07.2013, C79000-G8976-C174-22 SIMATIC S7-300 1.1 CP 342-5 / CP 342-5 FO Characteristic data of the device Order numbers / versions Features / new or modified functions Order number: Firmware modification: 6GK7 342-5DA02-0XE0 6GK7 342-5DF00-0XE0 * Enhanced functions: The routing of PG connections is now also possible with the CP in STOP mode; Hardware product version: 4 * Hardware product version: 5 Firmware version: V5.5 Relevant documentation: S7 CPs for PROFIBUS manual as of Release 04 - 02/2003 Required STEP 7 Version (for full functionality) STEP 7 Version V5.1 SP2 or higher can be configured as firmware version V5.0 Bugs fixed (for example in the CP functions: S7 routing; online/offline block comparison in the SIMATIC Manager; download of configurations; stability if disruptions occur on PROFIBUS); The firmware version is compatible and can be used with hardware product versions 1, 3 and 4, 5 * General section: Hardware modification for 6GK7 342-5DA02-0XE0: 1158693 The change in the version is only due to production (http://support.automation.siemens.com and does not represent any change in function. /ww/view/de/1158693) Part specific to the CP 342-5 / CP 342-5 FO 8773570 (http://support.automation.siemens.com /ww/view/de/8773570) * SIMATIC NET updates with firmware release: 22794601 (http://support.automation.siemens.com /ww/view/de/22794601) Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS Reference Manual, 07.2013, C79000-G8976-C174-22 15 SIMATIC S7-300 1.1 CP 342-5 / CP 342-5 FO Characteristic data of the device Order numbers / versions Features / new or modified functions Order number: Firmware modification: 6GK7 342-5DA02-0XE0 * 6GK7 342-5DF00-0XE0 Hardware product version: 4 Firmware version: V5.4 Bugs fixed, no functional modifications compared with the previous version. The firmware version is compatible and can be used with hardware product versions 1, 3 and 4 Required STEP 7 Version (for full functionality) STEP 7 Version V5.1 SP2 or higher can be configured as firmware version V5.0 Relevant documentation: S7 CPs for PROFIBUS manual as of Release 04 - 02/2003 * General section: 1158693 (http://support.automation.siemens.com /ww/view/de/1158693) Part specific to the CP 342-5 / CP 342-5 FO 8773570 (http://support.automation.siemens.com /ww/view/de/8773570) * SIMATIC NET update with CP release: 14261822 (http://support.automation.siemens.com /ww/view/de/14261822) SIMATIC NET updates with firmware release: 19726245 (http://support.automation.siemens.com /ww/view/de/19726245) Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS 16 Reference Manual, 07.2013, C79000-G8976-C174-22 SIMATIC S7-300 1.1 CP 342-5 / CP 342-5 FO Characteristic data of the device Order numbers / versions Features / new or modified functions Order number: Firmware modification: 6GK7 342-5DA02-0XE0 * 6GK7 342-5DF00-0XE0 Hardware product version: 4 Firmware version: V5.2 Bugs fixed, no functional modifications compared with the previous version. The firmware version is compatible and can be used with hardware product versions 1, 3 and 4 Required STEP 7 Version (for full functionality) STEP 7 Version V5.1 SP2 or higher can be configured as firmware version V5.0 Relevant documentation: S7 CPs for PROFIBUS manual Release 04 - 2/2003 * General section 1158693 (http://support.automation.siemens.com /ww/view/de/1158693) Part specific to the CP 342-5 / CP 342-5 FO 8773570 (http://support.automation.siemens.com /ww/view/de/8773570) * SIMATIC NET updates with firmware release: 14261822 (http://support.automation.siemens.com /ww/view/de/14261822) 14222660 (http://support.automation.siemens.com /ww/view/de/14222660) Order number: Hardware modification: 6GK7 342-5DA02-0XE0 * 6GK7 342-5DF00-0XE0 Hardware product version: 4 Firmware version: V5.1 Relevant documentation: Bugs fixed, no functional modifications compared with the previous version. The firmware version is unchanged and therefore compatible and can be used with hardware product versions 1, 3 and 4 STEP 7 Version V5.1 SP2 or higher can be configured as firmware version V5.0 S7 CPs for PROFIBUS manual Release 03 - 11/2002 SIMATIC NET update with CP release: 14261822 (http://support.automation.siemens.com /ww/view/de/14261822) 10605200 (http://support.automation.siemens.com /ww/view/de/10605200) Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS Reference Manual, 07.2013, C79000-G8976-C174-22 17 SIMATIC S7-300 1.1 CP 342-5 / CP 342-5 FO Characteristic data of the device Order numbers / versions Features / new or modified functions Order number: Hardware modification: 6GK7 342-5DA02-0XE0 * 6GK7 342-5DF00-0XE0 Hardware product version: 3 Firmware version: V5.1 Relevant documentation: Bugs fixed, no functional modifications compared with the previous version. The firmware version is unchanged and therefore compatible and can be used with hardware product versions 1 and 3 Required STEP 7 Version (for full functionality) STEP 7 Version V5.1 SP2 or higher can be configured as firmware version V5.0 S7 CPs for PROFIBUS manual Release 03 - 11/2002 SIMATIC NET update with CP release: 12324024 (http://support.automation.siemens.com /ww/view/de/12324024) Extended functionality compared with the previous firmware version: STEP 7 Version V5.1 SP2 or higher 6GK7 342-5DF00-0XE0 - none; bug fixes only - Hardware product version: 2 * can be configured as firmware version V5.0 Order number: 6GK7 342-5DA02-0XE0 Firmware version: V5.1 Relevant documentation: compatible and usable with hardware product versions 1 and 2 S7 CPs for PROFIBUS manual Hardware modification: Release 01 - 6/2001 * SIMATIC NET update with CP release: due to production, functionally compatible with predecessor version 10605200 (http://support.automation.siemens.com /ww/view/de/10605200) 10604648 (http://support.automation.siemens.com /ww/view/de/10604648) Order number: 6GK7 342-5DA02-0XE0 6GK7 342-5DF00-0XE0 Hardware product version: 1 Firmware version: V5.0 Relevant documentation: S7 CPs for PROFIBUS manual Release 01 - 6/2001 SIMATIC NET updates with firmware release: The CP 342-5 can be used as a replacement for the following previous products: STEP 7 Version V5.1 SP2 or higher CP 342-5 order no.: 6GK7 342-5DA00-0XE0 CP 342-5 order no.: 6GK7 342-5DA01-0XE0 The CP 342-5 and CP 342-5 FO named here are functionally compatible. Extended functionality compared with the previous firmware version: * Multiplexing OP connections * S7 communication via loadable communication blocks (client function) 8928271 (http://support.automation.siemens.com * /ww/view/de/8928271) Extensive S7 connection diagnostics Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS 18 Reference Manual, 07.2013, C79000-G8976-C174-22 SIMATIC S7-300 1.1 CP 342-5 / CP 342-5 FO Characteristic data of the device Order numbers / versions Features / new or modified functions Required STEP 7 Version (for Order number: Extended functionality compared with the previous firmware version: STEP 7 Version V5.1 or higher - none; bug fixes only - can be configured as firmware version V4.0 Extended functionality compared with previous product (6GK7-342-5DA01-0XE0): STEP 7 Version V5.1 or higher 6GK7 342-5DA02-0XE0 6GK7 342-5DF00-0XE0 Hardware product version: 1 full functionality) Firmware version: V4.1 Relevant documentation: S7 CPs for PROFIBUS manual no change compared with firmware version V4.0 SIMATIC NET updates with firmware release: 6567193 (http://support.automation.siemens.com /ww/view/de/6567193) Order number: 6GK7 342-5DA02-0XE0 Hardware product version: 1 * The transmission speeds are also supported: 3, 6, 12 Mbps Firmware version: V4.0 * Relevant documentation: * 6GK7 342-5DF00-0XE0 Manual CP 342-5 / CP 342-5 FO (included on the S7 CP Documentation CD 10/2000) extended I/O configuration limits additional CP variant with integrated fiber-optic connector Additional feature: single module width (predecessor double width) SIMATIC NET update with CP release: 4893757 (http://support.automation.siemens.com /ww/view/de/4893757) 4894043 (http://support.automation.siemens.com /ww/view/de/4894043) Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS Reference Manual, 07.2013, C79000-G8976-C174-22 19 SIMATIC S7-300 1.1 CP 342-5 / CP 342-5 FO Characteristic data of the device Order numbers / versions Features / new or modified functions Required STEP 7 Version (for Order number: 6GK7-342-5DA01-0XE0 Extended functionality compared with previous product CP 342-5 (6GK7 342-5DA00-0XE0): STEP 7 Version V5.0 or higher Hardware product version: 2 * Firmware loader Firmware version: V3.00 * Distribution of bus parameters The firmware can be obtained at: * Replacing a module without a programming device 753015 * (http://support.automation.siemens.com /ww/view/de/753015) full functionality) Routing of PG functions The GSD file can be obtained at: 113652 (http://support.automation.siemens.com /ww/view/de/113652) Relevant documentation: Product information bulletin CP 342-5 Document no.: C79000-Z8964-C03203 SIMATIC NET update with CP release: 4245051 (http://support.automation.siemens.com /ww/view/de/4245051) Order number: Basic functionality with: 6GK7-342-5DA00-0XE0 * PROFIBUS-DP as DP master or DP slave * S5-compatible communication via FDL connections * S7 communication Hardware product version: 13 Firmware version: V 1.50 The firmware: You will find information about the SIM package 287 at: STEP 7 Version V5.0 or higher 4245101 (http://support.automation.siemens.com /ww/view/de/4245101) The GSD file can be obtained at: 113652 (http://support.automation.siemens.com /ww/view/de/113652) Relevant documentation: Product information bulletin CP 342-5 Document no.: C79000-Z8964-C02107 SIMATIC NET update with CP release: 4245101 (http://support.automation.siemens.com /ww/view/de/4245101) Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS 20 Reference Manual, 07.2013, C79000-G8976-C174-22 SIMATIC S7-300 1.2 CP 343-5 1.2 CP 343-5 1.2.1 Current version Characteristic data of the device Required STEP 7 Version (for Order numbers / versions Features / new or modified functions full functionality) Order number: Hardware modification: STEP 7 6GK7 343-5FA01-0XE0 * * Due to production, no functional modifications compared with the previous hardware product version. Firmware version: V4.2 The firmware version is unchanged and The firmware can be obtained at: therefore compatible and can be used 19725255 with hardware product versions 1 and 3 (http://support.automation.siemens.com to 6 /ww/view/de/19725255) Hardware product version: 6 STEP 7 Version V5.1 SP2 or higher You configure the CP as firmware version V4.0. Relevant documentation: S7 CPs for PROFIBUS manual as of Release 03 - 11/2002 * General section 1158693 (http://support.automation.siemens.com /ww/view/en/1158693) * Part specific to the CP 343-5 8778841 (http://support.automation.siemens.com /ww/view/de/8778841) SIMATIC NET update with CP release: 31803331 (http://support.automation.siemens.com /ww/view/en/31803331) SIMATIC NET updates with firmware release: 19725912 (http://support.automation.siemens.com /ww/view/de/19725912) Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS Reference Manual, 07.2013, C79000-G8976-C174-22 21 SIMATIC S7-300 1.2 CP 343-5 1.2.2 Previous versions Characteristic data of the device Required STEP 7 Version (for Order numbers / versions Features / new or modified functions full functionality) Order number: Hardware modification: STEP 7 6GK7 343-5FA01-0XE0 * * Bugs fixed, no functional modifications compared with the previous hardware product version. Firmware version: V4.2 The firmware version is unchanged and The firmware can be obtained at: therefore compatible and can be used 19725255 with hardware product versions 1, 3, 4 (http://support.automation.siemens.com and 5 /ww/view/de/19725255) Hardware product version: 5 STEP 7 Version V5.1 SP2 or higher You configure the CP as firmware version V4.0. Relevant documentation: S7 CPs for PROFIBUS manual as of Release 03 - 11/2002 * General section 1158693 (http://support.automation.siemens.com /ww/view/en/1158693) * Part specific to the CP 343-5 8778841 (http://support.automation.siemens.com /ww/view/de/8778841) SIMATIC NET update with CP release: 14261822 (http://support.automation.siemens.com /ww/view/de/14261822) SIMATIC NET updates with firmware release: 19725912 (http://support.automation.siemens.com /ww/view/de/19725912) Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS 22 Reference Manual, 07.2013, C79000-G8976-C174-22 SIMATIC S7-300 1.2 CP 343-5 Characteristic data of the device Order numbers / versions Features / new or modified functions Order number: Firmware modification: 6GK7 343-5FA01-0XE0 * Hardware product version: 4 Firmware version: V4.2 The firmware can be obtained at: Bugs fixed, no functional modifications compared with the previous version. The firmware version is compatible and can be used with hardware product versions 1, 3 and 4 Required STEP 7 Version (for full functionality) STEP 7 Version V5.1 SP2 or higher can be configured as firmware version V4.0 19725255 (http://support.automation.siemens.com /ww/view/de/19725255) Relevant documentation: S7 CPs for PROFIBUS manual as of Release 03 - 11/2002 * General section 1158693 (http://support.automation.siemens.com /ww/view/en/1158693) * Part specific to the CP 343-5 8778841 (http://support.automation.siemens.com /ww/view/de/8778841) SIMATIC NET update with CP release: 14261822 (http://support.automation.siemens.com /ww/view/de/14261822) SIMATIC NET updates with firmware release: 19725912 (http://support.automation.siemens.com /ww/view/de/19725912) Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS Reference Manual, 07.2013, C79000-G8976-C174-22 23 SIMATIC S7-300 1.2 CP 343-5 Characteristic data of the device Order numbers / versions Features / new or modified functions Order number: Hardware modification: 6GK7 343-5FA01-0XE0 * Hardware product version: 4 Firmware version: V4.1 Relevant documentation: S7 CPs for PROFIBUS manual Bugs fixed, no functional modifications compared with the previous version. The firmware version is unchanged and therefore compatible and can be used with hardware product versions 1, 3 and 4 Required STEP 7 Version (for full functionality) STEP 7 Version V5.1 SP2 or higher can be configured as firmware version V4.0 Release 03 - 11/2002 * General section 1158693 (http://support.automation.siemens.com /ww/view/en/1158693) * Part specific to the CP 343-5 8778841 (http://support.automation.siemens.com /ww/view/de/8778841) SIMATIC NET update with CP release: 14261822 (http://support.automation.siemens.com /ww/view/de/14261822) 10605201 (http://support.automation.siemens.com /ww/view/de/10605201) Order number: Hardware modification: 6GK7 343-5FA01-0XE0 * Hardware product version: 3 Firmware version: V4.1 Relevant documentation: S7 CPs for PROFIBUS manual Bugs fixed, no functional modifications compared with the previous hardware product version. The firmware version is unchanged and therefore compatible and can be used with hardware product versions 1 and 3 STEP 7 Version V5.1 SP2 or higher can be configured as firmware version V4.0 Release 03 - 11/2002 SIMATIC NET update with CP release: 10605201 (http://support.automation.siemens.com /ww/view/de/10605201) 12324022 (http://support.automation.siemens.com /ww/view/de/12324022) Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS 24 Reference Manual, 07.2013, C79000-G8976-C174-22 SIMATIC S7-300 1.2 CP 343-5 Characteristic data of the device Order numbers / versions Features / new or modified functions Required STEP 7 Version (for Order number: Extended functionality compared with the previous firmware version: STEP 7 Version V5.1 SP2 or higher Hardware product version: 2 - none; bug fixes only - Firmware version: V4.1 * can be configured as firmware version V4.0 6GK7 343-5FA01-0XE0 Relevant documentation: S7 CPs for PROFIBUS manual compatible and usable with hardware product versions 1 and 2 Release 01 - 6/2001 Hardware modification: SIMATIC NET update with CP release: * 10605201 (http://support.automation.siemens.com /ww/view/de/10605201) full functionality) due to production, functionally compatible with predecessor version 10605523 (http://support.automation.siemens.com /ww/view/de/10605523) Order number: 6GK7 343-5FA01-0XE0 Hardware product version: 1 Firmware version: V4.0 Relevant documentation: S7 CPs for PROFIBUS manual Release 01 - 6/2001 SIMATIC NET update with CP release: 8117953 (http://support.automation.siemens.com /ww/view/de/8117953) The CP 343-5 can be used as a replacement for the predecessor product CP 343-5 (6GK7 343-5FA000XE0). STEP 7 Version V5.1 SP2 or higher Extended functionality compared with previous product (6GK7-342-5FA00-0XE0): * The transmission speeds are also supported: 3, 6, 12 Mbps Additional feature: single module width (predecessor double width) Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS Reference Manual, 07.2013, C79000-G8976-C174-22 25 SIMATIC S7-300 1.2 CP 343-5 1.2.3 Predecessor modules Characteristic data of the device Order numbers / versions Features / new or modified functions Order number: Basic functionality with: 6GK7 343-5FA00-0XE0 * PROFIBUS FMS (complying with EN 50170, FMS client and server function) * S5-compatible communication via FDL connections Hardware product version: 6 Firmware version: V3.0 The firmware can be obtained at: * 786302 (http://support.automation.siemens.com * /ww/view/de/786302) * Relevant documentation: Required STEP 7 Version (for full functionality) STEP 7 Version V5.0 SP3 or higher S7 communication (server) Replacing a module without a programming device Routing of PG functions Product information bulletin CP 343-5 Document no.: C79000-Z8964-C7-04 SIMATIC NET update with CP release: 4245246 (http://support.automation.siemens.com /ww/view/de/4245246) Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS 26 Reference Manual, 07.2013, C79000-G8976-C174-22 2 SIMATIC S7-400 2.1 CP 443-5 Basic 2.1.1 Current version Characteristic data of the device Required STEP 7 Version (for Order numbers / versions Features / new or modified functions full functionality) Order number: Hardware modification: STEP 7 6GK7 443-5FX02-0XE0 * Hardware product version: 3 Firmware version: V4.0 due to production, functionally compatible with predecessor version The firmware can be obtained at: * STEP 7 as of version V5.2 SP1 You configure the CP as firmware version V4.0. 17817495 (http://support.automation.siemens.com /ww/view/de/17817495) Relevant documentation: S7 CPs for PROFIBUS manual as of Release 03 - 11/2002 * General section 1158693 (http://support.automation.siemens.com /ww/view/en/1158693) * Part specific to the CP 443-5 Basic 8776422 (http://support.automation.siemens.com /ww/view/de/8776422) Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS Reference Manual, 07.2013, C79000-G8976-C174-22 27 SIMATIC S7-400 2.1 CP 443-5 Basic 2.1.2 Previous versions Characteristic data of the device Order numbers / versions Features / new or modified functions Order number: Hardware modification: 6GK7 443-5FX02-0XE0 * Hardware product version: 2 due to production, functionally compatible with predecessor version Required STEP 7 Version (for full functionality) STEP 7 as of version V5.2 SP1 Firmware version: V4.0 The firmware can be obtained at: 17817495 (http://support.automation.siemens.com /ww/view/de/17817495) Relevant documentation: S7 CPs for PROFIBUS manual as of Release 03 - 11/2002 * General section 1158693 (http://support.automation.siemens.com /ww/view/en/1158693) * Part specific to the CP 443-5 Basic 8776422 (http://support.automation.siemens.com /ww/view/de/8776422) Order number: New hardware: 6GK7 443-5FX02-0XE0 * Firmware version: V4.0 The device is functionally compatible with the predecessor version. Modified / improved product characteristics: Relevant documentation: * additional PROFIBUS bus fault LED BUSF-LED) S7 CPs for PROFIBUS manual * improved performance (factor of 3) * reduced current consumption / power dissipation Hardware product version: 1 as of Release 03 - 11/2002 STEP 7 as of version V5.2 SP1 * General section 1158693 (http://support.automation.siemens.com /ww/view/en/1158693) * Part specific to the CP 443-5 Basic 8776422 (http://support.automation.siemens.com /ww/view/de/8776422) SIMATIC NET update with CP release: 17143238 (http://support.automation.siemens.com /ww/view/de/17143238) Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS 28 Reference Manual, 07.2013, C79000-G8976-C174-22 SIMATIC S7-400 2.1 CP 443-5 Basic 2.1.3 Predecessor modules Characteristic data of the device Order numbers / versions Features / new or modified functions Order number: Hardware modification: 6GK7 443-5FX01-0XE0 * Hardware product version: 3 due to production, functionally compatible with predecessor version Required STEP 7 Version (for full functionality) STEP 7 Version V5.1 SP1 or higher Firmware version: V3.2 The firmware can be obtained at: 5452112 (http://support.automation.siemens.com /ww/view/de/5452112) Relevant documentation: S7 CPs for PROFIBUS manual Release 03 - 11/2002 * General section 1158693 (http://support.automation.siemens.com /ww/view/en/1158693) * Part specific to the CP 443-5 Basic 8776422 (http://support.automation.siemens.com /ww/view/de/8776422) SIMATIC NET update with CP release: 10605528 (http://support.automation.siemens.com /ww/view/de/10605528) Order number: 6GK7 443-5FX01-0XE0 Hardware product version: 2 Firmware version: V3.2 Relevant documentation: S7 CPs for PROFIBUS manual Release 01 SIMATIC NET update with CP release: The CP 443-5 Basic listed here can be used as a replacement for the predecessor product CP 443-5 Basic (6GK7 443-5FX00-0XE0). STEP 7 Version V5.1 SP1 or higher Extended functionality compared with the previous firmware version: - none; bug fixes only (Extended functionality compared with previous product: see under version 1) 5472312 (http://support.automation.siemens.com /ww/view/de/5472312) Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS Reference Manual, 07.2013, C79000-G8976-C174-22 29 SIMATIC S7-400 2.1 CP 443-5 Basic Characteristic data of the device Order numbers / versions Features / new or modified functions Required STEP 7 Version (for Order number: Extended functionality compared with the previous firmware version: STEP 7 Version V5.0 SP3 or higher 6GK7 443-5FX01-0XE0 Hardware product version: 2 full functionality) - none; bug fixes only - Firmware version: V3.1 Relevant documentation: CP 443-5 Basic product information Document no.: C79000-Z8964-C05502 SIMATIC NET update with CP release: 4246730 (http://support.automation.siemens.com /ww/view/de/4246730) Order number: 6GK7 443-5FX01-0XE0 Hardware product version: 1 Extended functionality compared with the previous firmware version: STEP 7 Version V5.0 SP3 or higher - none; bug fixes only - Firmware version: V3.1 Relevant documentation: CP 443-5 Basic product information Document no.: C79000-Z8964-C05502 SIMATIC NET update with CP release: 4246662 (http://support.automation.siemens.com /ww/view/de/4246662) Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS 30 Reference Manual, 07.2013, C79000-G8976-C174-22 SIMATIC S7-400 2.1 CP 443-5 Basic Characteristic data of the device Order numbers / versions Features / new or modified functions Required STEP 7 Version (for Order number: 6GK7 443-5FX01-0XE0 Extended functionality compared with previous product CP 443-5 Basic (6GK7 443-5FX00-0XE0): STEP 7 Version V5.0 SP3 or higher Hardware product version: 1 * Routing of PG functions Firmware version: V3.0 * Replacing a module without a programming device Relevant documentation: * Use in SIMATIC S7-400H (fault-tolerant automation system) * Time-of-day synchronization CP 443-5 Basic product information Document no.: C79000-Z8964-C05501 full functionality) SIMATIC NET update with CP release: 4245091 (http://support.automation.siemens.com /ww/view/de/4245091) Order number: Basic functionality with: 6GK7 443-5FX00-0XE0 * PROFIBUS FMS (complying with EN 50170, FMS client and server function) * S5-compatible communication via FDL connections Hardware product version: 9 Firmware version: V2.42 The firmware can be obtained at: * 754121 (http://support.automation.siemens.com /ww/view/de/754121) STEP 7 Version V5.0 SP3 or higher S7 communication (server) Relevant documentation: CP 443-5 Basic product information Document no.: C79000-Z8964-C00805 SIMATIC NET update with CP release: 4245081 (http://support.automation.siemens.com /ww/view/de/4245081) Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS Reference Manual, 07.2013, C79000-G8976-C174-22 31 SIMATIC S7-400 2.2 CP 443-5 Extended 2.2 CP 443-5 Extended 2.2.1 Current version Characteristic data of the device Required STEP 7 Version (for Order numbers / versions Features / new or modified functions full functionality) Order number: Firmware modification. 6GK7 443-5DX05-0XE0 Enhanced function: Hardware product version: 1 * Support of SIMATIC S7-400H V6 Product improvements and bugs fixed, including: Depending on the STEP 7 version you are using, you have the following options: Firmware version: V7.1.1 68189209 (http://support.automation.siemens.com * /ww/view/en/68189209) Relevant documentation: S7 CPs for PROFIBUS manual * General section as of Release 04 - 03/2009 1158693 (http://support.automation.siemens.com /ww/view/en/1158693) Part specific to the CP 443-5 Extended as of release 07 - 7/2011 * 8777196 (http://support.automation.siemens.com /ww/view/en/8777196) SIMATIC NET updates with firmware release: 68188938 (http://support.automation.siemens.com /ww/view/en/68188938) STEP 7 * Note: Firmware download (with firmware download profile "FWL_FAST_LOAD") is only available as of this STEP 7 version. Correction to data record routing (e.g. with SIMATIC PDM access). * PROFIBUS DP: Problem when using DP master class 2 services. * Time synchronization: Correction in time of day status. STEP 7 as of version V5.5 SP1 * STEP 7 as of version V5.4 SP4 You configure the CP as firmware version V6.3 or higher. * STEP 7 as of version V5.4 You configure the CP as firmware version V6.1. If you use the module as a replacement or when the functionality of the predecessor module is adequate, configuration and diagnostics are possible using earlier STEP 7 versions. STEP 7 Professional * V12 The full range of functions can be configured with firmware version V7.0 * V11 The functional range of the following CP type can be configured: - 6GK7 443-5DX04-0XE0 Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS 32 Reference Manual, 07.2013, C79000-G8976-C174-22 SIMATIC S7-400 2.2 CP 443-5 Extended 2.2.2 Previous versions Characteristic data of the device Required STEP 7 Version (for Order numbers / versions Features / new or modified functions full functionality) Order number: Hardware and firmware modification 6GK7 443-5DX05-0XE0 The device is functionally compatible with the predecessor version. Depending on the STEP 7 version you are using, you have the following options: Hardware product version: 1 Firmware version: V7.0 Relevant documentation: S7 CPs for PROFIBUS manual STEP 7 * STEP 7 as of version V5.5 SP1 * STEP 7 as of version V5.4 SP4 You configure the CP as firmware version V6.3 or higher. * General section as of Release 04 - 03/2009 1158693 (http://support.automation.siemens.com /ww/view/en/1158693) Part specific to the CP 443-5 Extended as of release 07 - 7/2011 * 8777196 (http://support.automation.siemens.com /ww/view/en/8777196) SIMATIC NET update with CP release: 54679920 (http://support.automation.siemens.com /ww/view/en/54679920) * STEP 7 as of version V5.4 You configure the CP as firmware version V6.1. If you use the module as a replacement or when the functionality of the predecessor module is adequate, configuration and diagnostics are possible using earlier STEP 7 versions. STEP 7 Professional The functional range of the following CP type can be configured: * 6GK7 443-5DX04-0XE0 Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS Reference Manual, 07.2013, C79000-G8976-C174-22 33 SIMATIC S7-400 2.2 CP 443-5 Extended 2.2.3 Predecessor modules Characteristic data of the device Required STEP 7 Version (for Order numbers / versions Features / new or modified functions full functionality) Order number: Firmware modification: 6GK7 443-5DX04-0XE0 Product improvement and bugs fixed, no functional modifications compared with the previous version. Depending on the STEP 7 version you are using, you have the following options: Hardware product version: 2 Firmware version: V6.8.1 The firmware can be obtained at: Product improvements and bugs fixed, including: 64933815 (http://support.automation.siemens.com * /ww/view/de/64933815) * Relevant documentation: S7 CPs for PROFIBUS manual * General section as of Release 04 - 03/2009 1158693 (http://support.automation.siemens.com /ww/view/en/1158693) Part specific to the CP 443-5 Extended as of release 06 - 6/2005 * 8777196 (http://support.automation.siemens.com /ww/view/de/8777196) SIMATIC NET updates with firmware release: 64933813 (http://support.automation.siemens.com /ww/view/en/48072265) PROFIBUS DP: Problem when using DP master class 2 services. Time synchronization: Correction in time of day status. For more information, refer to SIMATIC NET updates STEP 7 * STEP 7 V5.5 SP1 You configure the CP as 6GK7 443-5DX04-0XE0 * STEP 7 as of version V5.4 SP4 You configure the CP as firmware version V6.3 or higher. * STEP 7 as of version V5.4 You configure the CP as firmware version V6.1 * STEP 7 as of version V5.2 SP1 You configure the CP as firmware version V6.0 If you use the module as a replacement or when the functionality of the predecessor module is adequate, configuration and diagnostics are possible using earlier STEP 7 versions. STEP 7 Professional * STEP 7 V11.0 You configure the CP as 6GK7 443-5DX04-0XE0 Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS 34 Reference Manual, 07.2013, C79000-G8976-C174-22 SIMATIC S7-400 2.2 CP 443-5 Extended Characteristic data of the device Required STEP 7 Version (for Order numbers / versions Features / new or modified functions full functionality) Order number: Firmware modification: 6GK7 443-5DX04-0XE1 Product improvement and bugs fixed, no functional modifications compared with the previous version. Depending on the STEP 7 version you are using, you have the following options: Hardware product version: 1 Firmware version: V6.8.1 The firmware can be obtained at: Product improvements and bugs fixed, including: 64933815 (http://support.automation.siemens.com * /ww/view/de/64933815) * Relevant documentation: S7 CPs for PROFIBUS manual * General section as of Release 04 - 03/2009 1158693 (http://support.automation.siemens.com /ww/view/en/1158693) PROFIBUS DP: Problem when using DP master class 2 services. Time synchronization: Correction in time of day status. For more information, refer to SIMATIC NET updates Part specific to the CP 443-5 Extended as of release 06 - 6/2005 * 8777196 (http://support.automation.siemens.com /ww/view/de/8777196) SIMATIC NET updates with firmware release: 64933813 (http://support.automation.siemens.com /ww/view/en/48072265) STEP 7 * STEP 7 V5.5 SP1 You configure the CP as 6GK7 443-5DX04-0XE0 * STEP 7 as of version V5.4 SP4 You configure the CP as firmware version V6.3 or higher. * STEP 7 as of version V5.4 You configure the CP as firmware version V6.1 * STEP 7 as of version V5.2 SP1 You configure the CP as firmware version V6.0 If you use the module as a replacement or when the functionality of the predecessor module is adequate, configuration and diagnostics are possible using earlier STEP 7 versions. STEP 7 Professional * STEP 7 V11.0 You configure the CP as 6GK7 443-5DX04-0XE0 Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS Reference Manual, 07.2013, C79000-G8976-C174-22 35 SIMATIC S7-400 2.2 CP 443-5 Extended Characteristic data of the device Required STEP 7 Version (for Order numbers / versions Features / new or modified functions full functionality) Order number: Hardware modification: 6GK7 443-5DX04-0XE1 * Depending on the STEP 7 version you are using, you have the following options: Hardware product version: 1 Firmware version: V6.7 Relevant documentation: S7 CPs for PROFIBUS manual * General section as of Release 04 - 03/2009 1158693 (http://support.automation.siemens.com /ww/view/en/1158693) Part specific to the CP 443-5 Extended as of release 06 - 6/2005 * 8777196 (http://support.automation.siemens.com /ww/view/de/8777196) SIMATIC NET updates with firmware release: 48072265 (http://support.automation.siemens.com /ww/view/en/48072265) due to production, functionally compatible with predecessor version The module does not conform to RoHS. STEP 7 You configure the CP as 6GK7 443-5DX04-0XE0 * STEP 7 as of version V5.4 SP4 You configure the CP as firmware version V6.3 or higher. * STEP 7 as of version V5.4 You configure the CP as firmware version V6.1 If you use the module as a replacement or when the functionality of the predecessor module is adequate, configuration and diagnostics are possible using earlier STEP 7 versions. STEP 7 Professional You configure the CP as 6GK7 443-5DX04-0XE0 Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS 36 Reference Manual, 07.2013, C79000-G8976-C174-22 SIMATIC S7-400 2.2 CP 443-5 Extended Characteristic data of the device Required STEP 7 Version (for Order numbers / versions Features / new or modified functions full functionality) Order number: Firmware modification: 6GK7 443-5DX04-0XE0 Product improvement and bugs fixed, no functional modifications compared with the previous version. Depending on the STEP 7 version you are using, you have the following options: Hardware product version: 2 Firmware version: V6.6 The firmware can be obtained at: Product improvements: * 48067029 (http://support.automation.siemens.com /ww/view/en/48067029) * Relevant documentation: Improvement of the display of the EXTF LED Improved response to bus shortcircuits S7 CPs for PROFIBUS manual * General section as of Release 04 - 03/2009 1158693 (http://support.automation.siemens.com /ww/view/en/1158693) * STEP 7 as of version V5.4 SP4 You configure the CP as firmware version V6.3 or higher. * STEP 7 as of version V5.4 You configure the CP as firmware version V6.1 If you use the module as a replacement or when the functionality of the predecessor module is adequate, configuration and diagnostics are possible using earlier STEP 7 versions. Part specific to the CP 443-5 Extended as of release 06 - 6/2005 * 8777196 (http://support.automation.siemens.com /ww/view/de/8777196) SIMATIC NET updates with firmware release: 48072265 (http://support.automation.siemens.com /ww/view/en/48072265) Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS Reference Manual, 07.2013, C79000-G8976-C174-22 37 SIMATIC S7-400 2.2 CP 443-5 Extended Characteristic data of the device Required STEP 7 Version (for Order numbers / versions Features / new or modified functions full functionality) Order number: Firmware modification: 6GK7 443-5DX04-0XE0 Product improvement and bugs fixed, no functional modifications compared with the previous version. Depending on the STEP 7 version you are using, you have the following options: Hardware product version: 2 Firmware version: V6.5.11 The firmware can be obtained at: Product improvements: 42310454 (http://support.automation.siemens.com /ww/view/de/42310454) * Relevant documentation: * S7 CPs for PROFIBUS manual * General section as of Release 04 - 03/2009 1158693 (http://support.automation.siemens.com /ww/view/en/1158693) * Improvements in the behavior of the bus in H systems when using fast * DP slaves. A removed DP slave module is indicated by the EXTF-LED of the CPU even after turning station power off and on again. STEP 7 as of version V5.4 SP4 You configure the CP as firmware version V6.3 or higher. STEP 7 as of version V5.4 You configure the CP as firmware version V6.1 If you use the module as a replacement or when the functionality of the predecessor module is adequate, configuration and diagnostics are possible using earlier STEP 7 versions. Part specific to the CP 443-5 Extended as of release 06 - 6/2005 * 8777196 (http://support.automation.siemens.com /ww/view/de/8777196) SIMATIC NET updates with firmware release: 42310453 (http://support.automation.siemens.com /ww/view/de/42310453) Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS 38 Reference Manual, 07.2013, C79000-G8976-C174-22 SIMATIC S7-400 2.2 CP 443-5 Extended Characteristic data of the device Required STEP 7 Version (for Order numbers / versions Features / new or modified functions full functionality) Order number: Firmware modification: 6GK7 443-5DX04-0XE0 Product improvement and bugs fixed, no functional modifications compared with the previous version. Depending on the STEP 7 version you are using, you have the following options: Hardware product version: 2 Firmware version: V6.5 Product improvements: * STEP 7 as of version V5.4 SP4 You configure the CP as firmware Adaptation of the time version V6.3 or higher. 34830644 synchronization to conform with the (http://support.automation.siemens.com * STEP 7 as of version V5.4 standard (IEC 61158-6) by /ww/view/de/34830644) You configure the CP as firmware integrating time of day 2 in the timeRelevant documentation: version V6.1 of-day frame; S7 CPs for PROFIBUS manual If you use the module as a replacement * Improvements in the parameter * General section or when the functionality of the assignment of very slow DP slaves. predecessor module is adequate, as of Release 04 - 2/2003 The firmware version is compatible and configuration and diagnostics are 1158693 can be used with hardware product possible using earlier STEP 7 versions. (http://support.automation.siemens.com versions 1 and 2 /ww/view/en/1158693) The firmware can be obtained at: * Part specific to the CP 443-5 Extended as of release 06 - 6/2005 * 8777196 (http://support.automation.siemens.com /ww/view/de/8777196) SIMATIC NET updates with firmware release: 34828895 (http://support.automation.siemens.com /ww/view/de/34828895) Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS Reference Manual, 07.2013, C79000-G8976-C174-22 39 SIMATIC S7-400 2.2 CP 443-5 Extended Characteristic data of the device Required STEP 7 Version (for Order numbers / versions Features / new or modified functions full functionality) Order number: Firmware modification: STEP 7 as of version V5.4 6GK7 443-5DX04-0XE0 * Bugs fixed, no functional modifications compared with the previous version. The firmware version is compatible and can be used with hardware product versions 1, 2 and 3 You configure the CP as firmware version V6.1 Hardware product version: 2 Firmware version: V6.4 The firmware can be obtained at: 26372646 (http://support.automation.siemens.com /ww/view/de/26372646) If you use the module as a replacement or when the functionality of the predecessor module is adequate, configuration and diagnostics are possible using earlier STEP 7 versions. Relevant documentation: S7 CPs for PROFIBUS manual * General section as of Release 04 - 2/2003 1158693 (http://support.automation.siemens.com /ww/view/en/1158693) Part specific to the CP 443-5 Extended as of release 06 - 6/2005 * 8777196 (http://support.automation.siemens.com /ww/view/de/8777196) SIMATIC NET updates with firmware release: 26424892 (http://support.automation.siemens.com /ww/view/de/26424892) Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS 40 Reference Manual, 07.2013, C79000-G8976-C174-22 SIMATIC S7-400 2.2 CP 443-5 Extended Characteristic data of the device Required STEP 7 Version (for Order numbers / versions Features / new or modified functions full functionality) Order number: Firmware modification: STEP 7 as of version V5.4 6GK7 443-5DX04-0XE0 * Hardware product version: 2 Firmware version: V6.3 Relevant documentation: You configure the CP as firmware Bugs fixed, no functional version V6.1 modifications compared with the previous version (for details, refer to SIMATIC NET updates). S7 CPs for PROFIBUS manual * General section as of Release 04 - 2/2003 1158693 (http://support.automation.siemens.com /ww/view/en/1158693) Part specific to the CP 443-5 Extended as of release 06 - 6/2005 * 8777196 (http://support.automation.siemens.com /ww/view/de/8777196) SIMATIC NET updates with firmware release: 25374772 (http://support.automation.siemens.com /ww/view/de/25374772) Order number: Hardware modification: 6GK7 443-5DX04-0XE0 * Hardware product version: 2 Firmware version: V6.1 due to production, functionally compatible with predecessor version STEP 7 as of version V5.4 You configure the CP as firmware version V6.1 Relevant documentation: S7 CPs for PROFIBUS manual * General section as of Release 04 - 2/2003 1158693 (http://support.automation.siemens.com /ww/view/en/1158693) Part specific to the CP 443-5 Extended as of release 06 - 6/2005 * 8777196 (http://support.automation.siemens.com /ww/view/de/8777196) Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS Reference Manual, 07.2013, C79000-G8976-C174-22 41 SIMATIC S7-400 2.2 CP 443-5 Extended Characteristic data of the device Required STEP 7 Version (for Order numbers / versions Features / new or modified functions full functionality) Order number: Hardware and firmware modification STEP 7 as of version V5.4 6GK7 443-5DX04-0XE0 The device is functionally compatible with the predecessor version. Hardware product version: 1 Firmware version: V6.1 Relevant documentation: S7 CPs for PROFIBUS manual Modified / improved product characteristics: * * General section as of Release 04 - 2/2003 Getting the bus topology in a DP master system The CP 443-5 Extended operating as DP master supports the measurement of the PROFIBUS bus topology in a DP master system using a diagnostics repeater (DP slave). 1158693 (http://support.automation.siemens.com /ww/view/en/1158693) Part specific to the CP 443-5 Extended as of release 06 - 6/2005 * 8777196 (http://support.automation.siemens.com /ww/view/de/8777196) SIMATIC NET updates with firmware release: 21556240 (http://support.automation.siemens.com /ww/view/de/21556240) Order number: Hardware and firmware modification 6GK7 443-5DX04-0XE0 The device is functionally compatible with the predecessor version. Hardware product version: 1 Firmware version: V6.0 Relevant documentation: S7 CPs for PROFIBUS manual as of Release 04 - 2/2003 STEP 7 Version V5.2.1 or higher Modified / improved product characteristics: * * * General section * 1158693 (http://support.automation.siemens.com /ww/view/en/1158693) additional PROFIBUS bus fault LED BUSF-LED) improved performance (factor of 3) reduced current consumption / power dissipation Part specific to the CP 443-5 Extended 8777196 (http://support.automation.siemens.com /ww/view/de/8777196) * SIMATIC NET update with CP release: 19337545 (http://support.automation.siemens.com /ww/view/de/19337545) Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS 42 Reference Manual, 07.2013, C79000-G8976-C174-22 SIMATIC S7-400 2.2 CP 443-5 Extended Characteristic data of the device Required STEP 7 Version (for Order numbers / versions Features / new or modified functions full functionality) Order number: Firmware modification: 6GK7 443-5DX03-0XE0 Product improvements and bugs fixed, no functional modifications compared with the previous version. Depending on the STEP 7 version you are using, you have the following options: Hardware product version: 3 Firmware version: V5.3 The firmware can be obtained at: 34830645 (http://support.automation.siemens.com /ww/view/en/34830645) Product improvements: * Relevant documentation: S7 CPs for PROFIBUS manual Release 04 - 2/2003 * * General section * 8774037 (http://support.automation.siemens.com /ww/view/de/8774037) Part specific to the CP 443-5 Extended 8777196 (http://support.automation.siemens.com /ww/view/de/8777196) * * STEP 7 as of version V5.4 SP4 You configure the CP as firmware Adaptation of the time version V5.2 or higher. synchronization to conform with the or standard (IEC 61158-6) by * STEP 7 as of version V5.2 integrating time of day 2 in the timeof-day frame; You configure the CP as firmware version V5.0 or V5.1. Improvements in the parameter or assignment of very slow DP slaves; Plant changes using CiR (Configuration in RUN) can now also be made when large numbers of I/Os are involved. The firmware version is compatible and can be used with hardware product versions 1, 2 and 3 * STEP 7 Version V5.1 SP2 or higher You configure the CP as firmware version V4.0 If you use the module as a replacement or when the functionality of the predecessor module is adequate, configuration and diagnostics are possible using earlier STEP 7 versions. SIMATIC NET updates with firmware release: 34829451 (http://support.automation.siemens.com /ww/view/en/34829451) Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS Reference Manual, 07.2013, C79000-G8976-C174-22 43 SIMATIC S7-400 2.2 CP 443-5 Extended Characteristic data of the device Required STEP 7 Version (for Order numbers / versions Features / new or modified functions full functionality) Order number: Firmware modification: STEP 7 as of version V5.2 6GK7 443-5DX03-0XE0 Bugs fixed, no functional modifications compared with the previous version. can be configured as firmware version V5.1 Hardware product version: 3 Firmware version: V5.2 The firmware can be obtained at: 27201492 (http://support.automation.siemens.com /ww/view/de/27201492) The firmware version is compatible and can be used with hardware product versions 1, 2 and 3 Relevant documentation: S7 CPs for PROFIBUS manual Release 04 - 2/2003 * General section 8774037 (http://support.automation.siemens.com /ww/view/de/8774037) Part specific to the CP 443-5 Extended 8777196 (http://support.automation.siemens.com /ww/view/de/8777196) * SIMATIC NET updates with firmware release: 34829451 (http://support.automation.siemens.com /ww/view/en/34829451) Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS 44 Reference Manual, 07.2013, C79000-G8976-C174-22 SIMATIC S7-400 2.2 CP 443-5 Extended Characteristic data of the device Required STEP 7 Version (for Order numbers / versions Features / new or modified functions full functionality) Order number: Firmware modification: STEP 7 as of version V5.2 6GK7 443-5DX03-0XE0 Bugs fixed, no functional modifications compared with the previous version. can be configured as firmware version V5.0 Hardware product version: 3 Firmware version: V5.1 The firmware can be obtained at: 15121256 (http://support.automation.siemens.com /ww/view/de/15121256) The firmware version is compatible and can be used with hardware product versions 1, 2 and 3 Relevant documentation: S7 CPs for PROFIBUS manual Release 04 - 2/2003 * General section 8774037 (http://support.automation.siemens.com /ww/view/de/8774037) Part specific to the CP 443-5 Extended 8777196 (http://support.automation.siemens.com /ww/view/de/8777196) * SIMATIC NET update with CP release: 15117378 (http://support.automation.siemens.com /ww/view/de/15117378) 14256451 (http://support.automation.siemens.com /ww/view/de/14256451) Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS Reference Manual, 07.2013, C79000-G8976-C174-22 45 SIMATIC S7-400 2.2 CP 443-5 Extended Characteristic data of the device Required STEP 7 Version (for Order numbers / versions Features / new or modified functions full functionality) Order number: Hardware modification: STEP 7 as of version V5.2 6GK7 443-5DX03-0XE0 * Hardware product version: 3 Firmware version: V5.0 due to production, functionally compatible with predecessor version Relevant documentation: S7 CPs for PROFIBUS manual Release 04 - 2/2003 * General section 8774037 (http://support.automation.siemens.com /ww/view/de/8774037) Part specific to the CP 443-5 Extended 8777196 (http://support.automation.siemens.com /ww/view/de/8777196) * SIMATIC NET update with CP release: 14256451 (http://support.automation.siemens.com /ww/view/de/14256451) 6GK7 443-5DX03-0XE0 Extended functionality compared with the previous firmware version: Hardware product version: 2 * CiR functionality (with CiR, it is possible to add to or modify the distributed I/O during ongoing operation.) - in the standard system * Enabling /disabling DP slave - in the standard system Order number: Firmware version: V5.0 Relevant documentation: S7 CPs for PROFIBUS manual Release 03 - 11/2002 SIMATIC NET update with CP release: STEP 7 as of version V5.2 13729134 (http://support.automation.siemens.com /ww/view/de/13729134) Order number: Hardware modification: 6GK7 443-5DX03-0XE0 * Hardware product version: 2 Firmware version: V4.0 STEP 7 Version V5.1 SP2 or higher due to production, functionally compatible with predecessor version Relevant documentation: S7 CPs for PROFIBUS manual Release 01 - 6/2001 SIMATIC NET update with CP release: 10604437 (http://support.automation.siemens.com /ww/view/de/10604437) Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS 46 Reference Manual, 07.2013, C79000-G8976-C174-22 SIMATIC S7-400 2.2 CP 443-5 Extended Characteristic data of the device Required STEP 7 Version (for full functionality) Order numbers / versions Features / new or modified functions Order number: The CP 443-5 Extended listed here can STEP 7 Version V5.1 SP2 or higher be used as a replacement for the predecessor products CP 443-5 Extended (6GK7 443-5DX00-0XE0, 6GK7 443-5DX01-0XE0 and 6GK7 443-5DX02-0XE0) 6GK7 443-5DX03-0XE0 Hardware product version: 1 Firmware version: V4.0 Relevant documentation: Release 01 - 6/2001 Extended functionality compared with previous product: SIMATIC NET update with CP release: * S7 CPs for PROFIBUS manual * 8262972 (http://support.automation.siemens.com /ww/view/de/8262972) * Order number: 6GK7 443-5DX02-0XE0 Hardware product version: 2 DPV1 functionality. When using STEP7 V5.1 SP2 and the CPUs as of V3.0, there is a performance improvement in the transfer of consistent data (SFC14, SFC15). Consistent data can be stored in the full process image or in a partition (up to 32 bytes). To do this you no longer need to call SFC14 and SFC15. Updating is handled by the system. Extended functionality compared with the previous firmware version: - none; bug fixes only STEP 7 Version V5.1 or higher can be configured as firmware version V3.2 Firmware version: V3.3 The firmware can be obtained at: 12011123 (http://support.automation.siemens.com /ww/view/de/12011123) Relevant documentation: CP 443-5 Extended product information * Document no.: A5E 000 74498 SIMATIC NET update with CP release: 12011694 (http://support.automation.siemens.com /ww/view/de/12011694) Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS Reference Manual, 07.2013, C79000-G8976-C174-22 47 SIMATIC S7-400 2.2 CP 443-5 Extended Characteristic data of the device Required STEP 7 Version (for full functionality) Order numbers / versions Features / new or modified functions Order number: The CP 4435 Extended can be used as STEP 7 Version V5.1 or higher a replacement for the following previous products: 6GK7 443-5DX02-0XE0 Hardware product version: 2 Firmware version: V3.2 Relevant documentation: CP 443-5 Extended product information * Document no.: A5E 000 74498 SIMATIC NET update with CP release: CP 443-5 Extended Order no.: 6GK7 443-5DX01-0XE0 Order no.: 6GK7 443-5DX00-0XE0 Extended functionality compared with previous product CP 443-5 Extended (6GK7 443-5DX01-0XE0 V1.2.1): 4894460 * (http://support.automation.siemens.com /ww/view/de/4894460) expanded DP functionality (DP direct data exchange, constant bus cycle time) * Time-of-day synchronization * Routing of PG functions * Larger configuration memory * Use in SIMATIC S7-400H (faulttolerant) * Data record routing * Modifications to the plant during operation are possible (H system); * Optimized DP line failover (H system); Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS 48 Reference Manual, 07.2013, C79000-G8976-C174-22 SIMATIC S7-400 2.2 CP 443-5 Extended Characteristic data of the device Required STEP 7 Version (for full functionality) Order numbers / versions Features / new or modified functions Order number: The CP 4435 Extended can be used as STEP 7 Version V5.0 or higher a replacement for the following previous products: 6GK7 443-5DX01-0XE0 Product version: 2 Firmware version: V1.21 The firmware can be obtained at: CP 443-5 Extended Order no.: 6GK7 443-5DX00-0XE0 Extended functionality compared with 752061 previous product CP 443-5 Extended (http://support.automation.siemens.com (6GK7 443-5DX00-0XE0): /ww/view/de/752061) * Sync/freeze and free layer 2 access Relevant documentation: CP 443-5 Extended product information Document no.: C79000-Z8964-C3302 SIMATIC NET update with CP release: * 4245061 (http://support.automation.siemens.com /ww/view/de/4245061) Order number: Basic functionality with: 6GK7 443-5DX00-0XE0 * PROFIBUS-DP as DP master * S5-compatible communication via FDL connections * S7 communication Product version: 4 Firmware version: V1.10 The firmware can be obtained at: 184015 (http://support.automation.siemens.com /ww/view/de/184015) STEP 7 Version V5.0 or higher Relevant documentation: CP 443-5 Extended product information Document no.: C79000-Z8964-C903 SIMATIC NET update with CP release: * 4242783 (http://support.automation.siemens.com /ww/view/de/4242783) Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS Reference Manual, 07.2013, C79000-G8976-C174-22 49 SIMATIC S7-400 2.2 CP 443-5 Extended Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS 50 Reference Manual, 07.2013, C79000-G8976-C174-22