MT41K1G8RKB-107:P - MICRON TECHNOLOGY

TwinDie™ 1.35V DDR3L SDRAM

MT41K2G4 – 128 Meg x 4 x 8 Banks x 2 Ranks

MT41K1G8 – 64 Meg x 8 x 8 Banks x 2 Ranks

Description

The 8Gb (TwinDie™) DDR3L SDRAM (1.35V) uses

Micron’s 4Gb DDR3L SDRAM die (essentially two

ranks of the 4Gb DDR3L SDRAM). Refer to Micron’s

4Gb DDR3 SDRAM data sheet for the specifications

not included in this document. Specifications for base

part number MT41K1G4 correlate to TwinDie manu-

facturing part number MT41K2G4; specifications for

base part number MT41K512M8 correlate to TwinDie

manufacturing part number MT41K1G8.

Features

• Uses 4Gb Micron die

• Two ranks (includes dual CS#, ODT, CKE, and ZQ

balls)

• Each rank has eight internal banks for concurrent

operation

• VDD = VDDQ = 1.35V (1.283–1.45V); backward com-

patible to VDD = VDDQ = 1.5V ±0.075V

• 1.35V center-terminated push/pull I/O

• JEDEC-standard ball-out

• Low-profile package

• TC of 0°C to 95°C

– 0°C to 85°C: 8192 refresh cycles in 64ms

– 85°C to 95°C: 8192 refresh cycles in 32ms

– Industrial temperature (IT) available (Rev. E)

Options Marking

• Configuration

– 128 Meg x 4 x 8 banks x 2 ranks 2G4

– 64 Meg x 8 x 8 banks x 2 ranks 1G8

• 78-ball FBGA package (Pb-free)

– (9.5mm x 11.5mm x 1.2mm) Die

Rev :E

TRF

– (8mm x 10.5mm x 1.2mm) Die

Rev :N, P

RKB

• Timing – cycle time1

– 1.071ns @ CL = 13 (DDR3L-1866) -107

– 1.25ns @ CL = 11 (DDR3L-1600) -125

– 1.5ns @ CL = 9 (DDR3L-1333) -15E

• Self refresh

– Standard None

• Operating temperature

– Commercial (0°C ≤ TC ≤ 95°C) None

– Industrial (-40°C ≤ TC ≤ 95°C) IT

• Revision :E/:N/:P

Note: 1. CL = CAS (READ) latency.

Table 1: Key Timing Parameters

Speed Grade Data Rate (MT/s) Target tRCD-tRP-CL tRCD (ns) tRP (ns) CL (ns)

-1071, 21866 13-13-13 13.91 13.91 13.91

-125 11600 11-11-11 13.75 13.75 13.75

-15E 1333 9-9-9 13.5 13.5 13.5

Notes: 1. Backward compatible to 1333, CL = 9 (-15E).

2. Backward compatible to 1600, CL = 11 (-125).

8Gb: x4, x8 TwinDie DDR3L SDRAM

Description

CCMTD-1725822587-9746

DDR3L_8Gb_x4_x8_2CS_TwinDie_V90B.pdf - Rev. K 8/18 EN 1Micron Technology, Inc. reserves the right to change products or specifications without notice.

Products and specifications discussed herein are subject to change by Micron without notice.

Table 2: Addressing

Parameter 2048 Meg x 4 1024 Meg x 8

Configuration 128 Meg x 4 x 8 banks x 2 ranks 64 Meg x 8 x 8 banks x 2 ranks

Refresh count 8K 8K

Row address 64K A[15:0] 64K A[15:0]

Bank address 8 BA[2:0] 8 BA[2:0]

Column address 2K A[11, 9:0] 1K A[9:0]

8Gb: x4, x8 TwinDie DDR3L SDRAM

Description

CCMTD-1725822587-9746

DDR3L_8Gb_x4_x8_2CS_TwinDie_V90B.pdf - Rev. K 8/18 EN 2Micron Technology, Inc. reserves the right to change products or specifications without notice.

Ball Assignments and Descriptions

Figure 1: 78-Ball FBGA Ball Assignments (Top View)

4 65

VSS

VDDQ

VSSQ

VREFDQ

ODT1

ODT0

CS1#

VSS

VDD

VSS

VDD

VSS

VDD

VSSQ

DQ2

NF, DQ6

VDDQ

VSS

VDD

CS0#

BA0

RESET#

DQ0

DQS

DQS#

NF, DQ4

RAS#

CAS#

WE#

BA2

A13

NF, NF/TDQS#

DM, DM/TDQS

DQ1

VDD

NF, DQ7

CK#

A10/AP

A15

A12/BC#

A11

A14

VSS

VSSQ

DQ3

VSS

NF, DQ5

VSS

VDD

ZQ0

VREFCA

BA1

VDD

VDDQ

VSSQ

VDDQ

CKE1

CKE0

ZQ1

VSS

VDD

VSS

VDD

VSS

Note: 1. Dark balls (with ring) designate balls that differ from the monolithic versions.

8Gb: x4, x8 TwinDie DDR3L SDRAM

Ball Assignments and Descriptions

CCMTD-1725822587-9746

DDR3L_8Gb_x4_x8_2CS_TwinDie_V90B.pdf - Rev. K 8/18 EN 3Micron Technology, Inc. reserves the right to change products or specifications without notice.

Table 3: FBGA 78-Ball Descriptions

Symbol Type Description

A15, A14, A13,

A12/BC#, A11,

A10/AP, A[9:0]

Input Address inputs: Provide the row address for ACTIVATE commands, and the column ad-

dress and auto precharge bit (A10) for READ/WRITE commands, to select one location out

of the memory array in the respective bank. A10 sampled during a PRECHARGE com-

mand determines whether the PRECHARGE applies to one bank (A10 LOW, bank selected

by BA[2:0]) or all banks (A10 HIGH). The address inputs also provide the op-code during a

LOAD MODE command. Address inputs are referenced to VREFCA. A12/BC#: When enabled

in the mode register (MR), A12 is sampled during READ and WRITE commands to deter-

mine whether burst chop (on-the-fly) will be performed (HIGH = burst length (BL) of 8 or

no burst chop, LOW = burst chop (BC) of 4, burst chop).

BA[2:0] Input Bank address inputs: BA[2:0] define the bank to which an ACTIVATE, READ, WRITE, or

PRECHARGE command is being applied. BA[2:0] define which mode register (MR0, MR1,

MR2, or MR3) is loaded during the LOAD MODE command. BA[2:0] are referenced to

VREFCA.

CK, CK# Input Clock: CK and CK# are differential clock inputs. All command, address, and control input

signals are sampled on the crossing of the positive edge of CK and the negative edge of

CK#. Output data strobe (DQS, DQS#) is referenced to the crossings of CK and CK#.

CKE[1:0] Input Clock enable: CKE enables (registered HIGH) and disables (registered LOW) internal cir-

cuitry and clocks on the DRAM. The specific circuitry that is enabled/disabled is depend-

ent upon the DDR3L SDRAM configuration and operating mode. Taking CKE LOW pro-

vides PRECHARGE power-down and SELF REFRESH operations (all banks idle) or active

power-down (row active in any bank). CKE is synchronous for power-down entry and exit

and for self refresh entry. CKE is asynchronous for self refresh exit. Input buffers (exclud-

ing CK, CK#, CKE, RESET#, and ODT) are disabled during power-down. Input buffers (ex-

cluding CKE and RESET#) are disabled during SELF REFRESH. CKE is referenced to VREFCA.

CS#[1:0] Input Chip select: CS# enables (registered LOW) and disables (registered HIGH) the command

decoder. All commands are masked when CS# is registered HIGH. CS# provides for exter-

nal rank selection on systems with multiple ranks. CS# is considered part of the command

code.

DM Input Input data mask: DM is an input mask signal for write data. Input data is masked when

DM is sampled HIGH, along with the input data, during a write access. Although the DM

ball is input-only, the DM loading is designed to match that of the DQ and DQS balls. DM

is referenced to VREFDQ. DM has an optional use as TDQS on the x8.

ODT[1:0] Input On-die termination: ODT enables (registered HIGH) and disables (registered LOW) ter-

mination resistance internal to the DDR3L SDRAM. When enabled in normal operation,

ODT is only applied to each of the following balls: DQ[7:0], DQS, DQS#, and DM for the

x8; DQ[3:0], DQS, DQS#, and DM for the x4. The ODT input is ignored if disabled via the

LOAD MODE command. ODT is referenced to VREFCA.

RAS#, CAS#, WE# Input Command inputs: RAS#, CAS#, and WE# (along with CS#) define the command being

entered and are referenced to VREFCA.

RESET# Input Reset: RESET# is an active LOW CMOS input referenced to VSS. The RESET# input receiver

is a CMOS input defined as a rail-to-rail signal with DC HIGH ≥ 0.8 × VDDQ and DC LOW ≤

0.2 × VDDQ. RESET# assertion and desertion are asynchronous.

DQ[3:0] I/O Data input/output: Bidirectional data bus for x4 configuration. DQ[3:0] are referenced

to VREFDQ.

8Gb: x4, x8 TwinDie DDR3L SDRAM

Ball Assignments and Descriptions

CCMTD-1725822587-9746

DDR3L_8Gb_x4_x8_2CS_TwinDie_V90B.pdf - Rev. K 8/18 EN 4Micron Technology, Inc. reserves the right to change products or specifications without notice.

Table 3: FBGA 78-Ball Descriptions (Continued)

Symbol Type Description

DQ[7:0] I/O Data input/output: Bidirectional data bus for x8 configuration. DQ[7:0] are referenced

to VREFDQ.

DQS, DQS# I/O Data strobe: DQS and DQS# are differential data strobes: Output with read data; edge

aligned with read data; input with write data; center-aligned with write data.

TDQS, TDQS# I/O Termination data strobe: Applies to the x8 configuration only. When TDQS is enabled,

DM is disabled, and the TDQS and TDQS# balls provide termination resistance.

VDD Supply Power supply: 1.35V (1.283V to 1.45V operational; compatible with 1.5V operation)

VDDQ Supply DQ power supply: 1.35V (1.283V to 1.45V operational; compatible with 1.5V opera-

tion). Isolated on the device for improved noise immunity.

VREFCA Supply Reference voltage for control, command, and address: VREFCA must be maintained

at all times (including self refresh) for proper device operation.

VREFDQ Supply Reference voltage for data: VREFDQ must be maintained at all times (including self re-

fresh) for proper device operation.

VSS Supply Ground.

VSSQ Supply DQ ground: Isolated on the device for improved noise immunity.

ZQ[1:0] Reference External reference ball for output drive calibration: This ball is tied to an external

240Ω resistor (RZQ), which is tied to VSSQ.

NC – No connect: These balls should be left unconnected (the ball has no connection to the

DRAM or to other balls).

NF – No function: When configured as a x4 device, these balls are NF. When configured as a

x8 device, these balls are defined as TDQS#, DQ[7:4].

8Gb: x4, x8 TwinDie DDR3L SDRAM

Ball Assignments and Descriptions

CCMTD-1725822587-9746

DDR3L_8Gb_x4_x8_2CS_TwinDie_V90B.pdf - Rev. K 8/18 EN 5Micron Technology, Inc. reserves the right to change products or specifications without notice.

Functional Description

The TwinDie DDR3L SDRAM is a high-speed, CMOS dynamic random access memory

device internally configured as two 8-bank DDR3L SDRAM devices.

Although each die is tested individually within the dual-die package, some TwinDie test

results may vary from a like die tested within a monolithic die package.

The DDR3L SDRAM uses a double data rate architecture to achieve high-speed opera-

tion. The double data rate architecture is an 8n-prefetch architecture with an interface

designed to transfer two data words per clock cycle at the I/O balls. A single read or

write access consists of a single 8n-bit-wide, one-clock-cycle data transfer at the inter-

nal DRAM core and eight corresponding n-bit-wide, one-half-clock-cycle data transfers

at the I/O balls.

The differential data strobe (DQS, DQS#) is transmitted externally, along with data, for

use in data capture at the DDR3L SDRAM input receiver. DQS is center-aligned with da-

ta for WRITEs. The read data is transmitted by the DDR3L SDRAM and edge-aligned to

the data strobes.

Read and write accesses to the DDR3L SDRAM are burst-oriented. Accesses start at a

selected location and continue for a programmed number of locations in a program-

med sequence. Accesses begin with the registration of an ACTIVATE command, which is

then followed by a READ or WRITE command. The address bits registered coincident

with the ACTIVATE command are used to select the bank and row to be accessed. The

address bits (including CSn#, BAn, and An) registered coincident with the READ or

WRITE command are used to select the rank, bank, and starting column location for the

burst access.

This data sheet provides a general description, package dimensions, and the package

ballout. Refer to the Micron monolithic DDR3L data sheet for complete information re-

garding individual die initialization, register definition, command descriptions, and die

operation.

Industrial Temperature

The industrial temperature (IT) option, if offered, requires that the case temperature

not exceed –40°C or 95°C. JEDEC specifications require the refresh rate to double when

TC exceeds 85°C; this also requires use of the high-temperature self refresh option. Addi-

tionally, ODT resistance, IDD values, some IDD specifications and the input/output im-

pedance must be derated when TC is < 0°C or > 95°C. See the DDR3 monolithic data

sheet for details.

8Gb: x4, x8 TwinDie DDR3L SDRAM

Functional Description

CCMTD-1725822587-9746

DDR3L_8Gb_x4_x8_2CS_TwinDie_V90B.pdf - Rev. K 8/18 EN 6Micron Technology, Inc. reserves the right to change products or specifications without notice.

Functional Block Diagrams

Figure 2: Functional Block Diagram (128 Meg x 4 x 8 Banks x 2 Ranks)

RAS#

CAS#

WE#

CK#

DQ[3:0]

DQS, DQS#

A[15:0],

BA[2:0]

CS0#

CKE0

ODT0

Rank 0

(128 Meg x 4 x 8 banks)

Rank 1

(128 Meg x 4 x 8 banks)

CS1#

CKE1

ODT1

ZQ1 ZQ0

Figure 3: Functional Block Diagram (64 Meg x 8 x 8 Banks x 2 Ranks)

TDQS#

CAS#

RAS#

WE#

CK#

DQ[7:0]

DQS, DQS#

DM/TDQS

A[15:0],

BA[2:0]

Rank 0

(64 Meg x 8 x 8 banks)

Rank 1

(64 Meg x 8 x 8 banks)

CS0#

CKE0

ODT0

ZQ0

CS1#

CKE1

ODT1

ZQ1

8Gb: x4, x8 TwinDie DDR3L SDRAM

Functional Block Diagrams

CCMTD-1725822587-9746

DDR3L_8Gb_x4_x8_2CS_TwinDie_V90B.pdf - Rev. K 8/18 EN 7Micron Technology, Inc. reserves the right to change products or specifications without notice.

Electrical Specifications – Absolute Ratings

Stresses greater than those listed may cause permanent damage to the device. This is a

stress rating only, and functional operation of the device at these or any other condi-

tions outside those indicated in the device data sheet is not implied. Exposure to abso-

lute maximum rating conditions for extended periods may adversely affect reliability.

Table 4: Absolute Maximum DC Ratings

Parameter Symbol Min Max Units Notes

VDD supply voltage relative to VSS VDD –0.4 1.975 V 1

VDD supply voltage relative to VSSQ VDDQ –0.4 1.975 V

Voltage on any ball relative to VSS VIN, VOUT –0.4 1.975 V

Input leakage current

Any input 0V ≤ VIN ≤ VDD,

VREF pin 0V ≤ VIN ≤ 1.1V

(All other pins not under test = 0V)

II–4 4 µA

VREF supply leakage current

VREFDQ = VDD/2 or VREFCA = VDD/2

(All other pins not under test = 0V)

IVREF –2 2 µA 2

Operating case temperature TC0 95 °C 3, 4

Storage temperature TSTG –55 150 °C

Notes: 1. VDD and VDDQ must be within 300mV of each other at all times, and VREF must not be

greater than 0.6 × VDDQ. When VDD and VDDQ are less than 500mV, VREF may be ≤300mV.

2. The minimum limit requirement is for testing purposes. The leakage current on the VREF

pin should be minimal.

3. MAX operating case temperature. TC is measured in the center of the package (see Fig-

ure 4 (page 9)).

4. Device functionality is not guaranteed if the DRAM device exceeds the maximum TC dur-

ing operation.

Temperature and Thermal Impedance

It is imperative that the DDR3L SDRAM device’s temperature specifications, shown in

the following table, be maintained in order to ensure the junction temperature is in the

proper operating range to meet data sheet specifications. An important step in main-

taining the proper junction temperature is using the device’s thermal impedances cor-

rectly. The thermal impedances listed in Table 6 (page 10) apply to the current die re-

vision and packages.

Incorrectly using thermal impedances can produce significant errors. Read Micron

technical note TN-00-08, “Thermal Applications,” prior to using the values listed in the

thermal impedance table. For designs that are expected to last several years and require

the flexibility to use several DRAM die shrinks, consider using final target theta values

(rather than existing values) to account for increased thermal impedances from the die

size reduction.

The DDR3L SDRAM device’s safe junction temperature range can be maintained when

the TC specification is not exceeded. In applications where the device’s ambient tem-

8Gb: x4, x8 TwinDie DDR3L SDRAM

Electrical Specifications – Absolute Ratings

CCMTD-1725822587-9746

DDR3L_8Gb_x4_x8_2CS_TwinDie_V90B.pdf - Rev. K 8/18 EN 8Micron Technology, Inc. reserves the right to change products or specifications without notice.

perature is too high, use of forced air and/or heat sinks may be required to satisfy the

case temperature specifications.

Table 5: Thermal Characteristics

Notes 1–3 apply to entire table

Parameter Symbol Value Units Notes

Operating temperature TC0 to 85 °C

0 to 95 °C 4

Notes: 1. MAX operating case temperature TC is measured in the center of the package, as shown

below.

2. A thermal solution must be designed to ensure that the device does not exceed the

maximum TC during operation.

3. Device functionality is not guaranteed if the device exceeds maximum TC during

operation.

4. If TC exceeds 85°C, the DRAM must be refreshed externally at 2x refresh, which is a 3.9µs

interval refresh rate. The use of self refresh temperature (SRT) or automatic self refresh

(ASR), if available, must be enabled.

Figure 4: Temperature Test Point Location

Test point

Length (L)

Width (W)

0.5 (W)

0.5 (L)

8Gb: x4, x8 TwinDie DDR3L SDRAM

Electrical Specifications – Absolute Ratings

CCMTD-1725822587-9746

DDR3L_8Gb_x4_x8_2CS_TwinDie_V90B.pdf - Rev. K 8/18 EN 9Micron Technology, Inc. reserves the right to change products or specifications without notice.

Table 6: Thermal Impedance

Die Rev Package Substrate

Θ JA (°C/W)

Airflow =

0m/s

Θ JA (°C/W)

Airflow =

1m/s

Θ JA (°C/W)

Airflow =

2m/s Θ JB (°C/W) Θ JC (°C/W) Notes

E 78-ball

Low Con-

ductivity 57.7 44.1 38.8 NA 2.1

High Con-

ductivity 36.7 30.6 28.1 18.6 NA

N 78-ball

Low Con-

ductivity 53.1 41.4 37.3 NA 3.1

High Con-

ductivity 32.9 27.5 25.8 13.0 NA

P 78-ball

Low Con-

ductivity TBD TBD TBD TBD TBD

High Con-

ductivity TBD TBD TBD TBD TBD

Note: 1. Thermal resistance data is based on a number of samples from multiple lots and should

be viewed as a typical number.

8Gb: x4, x8 TwinDie DDR3L SDRAM

Electrical Specifications – Absolute Ratings

CCMTD-1725822587-9746

DDR3L_8Gb_x4_x8_2CS_TwinDie_V90B.pdf - Rev. K 8/18 EN 10 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Electrical Specifications – ICDD Parameters

Table 7: DDR3L ICDD Specifications and Conditions (Rev E)

Note 1 applies to the entire table

Combined

Symbol

Individual

Die Status

Bus

Width -187E -15E -125 -107 Units

ICDD0 ICDD0 =

IDD0 + IDD2P0 + 5

x4, x8 67 70 78 85 mA

ICDD1 ICDD1 =

IDD1 + IDD2P0 + 5

x4 76 80 84 88 mA

x8 82 85 89 93

ICDD2P0 (slow exit) ICDD2P0 =

IDD2P0 + IDD2P0

x4, x8 36 36 36 36 mA

ICDD2P1 (fast exit) ICDD2P1 =

IDD2P1 + IDD2P0

x4, x8 44 46 50 55 mA

ICDD2Q ICDD2Q =

IDD2Q + IDD2P0

x4, x8 45 46 50 53 mA

ICDD2N ICDD2N =

IDD2N + IDD2P0

x4, x8 46 47 50 53 mA

ICDD2N T ICDD2NT =

IDD2NT + IDD2P0

x4, x8 50 53 57 60 mA

ICDD3P ICDD3P = IDD3P +

IDD2P0

x4, x8 50 53 56 59 mA

ICDD3N ICDD3N =

IDD3N + IDD2P0

x4, x8 50 53 56 59 mA

ICDD4R ICDD4RCDD4R =

IDD4R + IDD2P0 + 5

x4 136 153 170 187 mA

x8 146 163 180 197

ICDD4W ICDD4W =

IDD4W + IDD2P0 + 5

x4 110 126 141 156 mA

x8 118 133 148 164

ICDD5B ICDD5B =

IDD5B + IDD2P0

x4, x8 242 246 253 260 mA

ICDD6 ICDD6 =

IDD6 + IDD6

x4, x8 40 40 40 40 mA

ICDD6ET ICDD6ET =

IDD6ET + IDD6ET

x4, x8 50 50 50 50 mA

ICDD7 ICDD7 =

IDD7 + IDD2P0 + 5

x4, x8 183 213 243 274 mA

ICDD8 ICDD8 = 2 × IDD2P0

+ 4

x4, x8 40 40 40 40 mA

Note: 1. ICDD values reflect the combined current of both individual die. IDDx represents individu-

al die values.

8Gb: x4, x8 TwinDie DDR3L SDRAM

Electrical Specifications – ICDD Parameters

CCMTD-1725822587-9746

DDR3L_8Gb_x4_x8_2CS_TwinDie_V90B.pdf - Rev. K 8/18 EN 11 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Table 8: DDR3L ICDD Specifications and Conditions (Rev N)

Note 1 applies to the entire table

Combined

Symbol

Individual

Die Status

Bus

Width -15E -125 -107 Units

ICDD0 ICDD0 =

IDD0 + IDD2P0+ 5

x4, x8 58 60 62 mA

ICDD1 ICDD1 =

IDD1 + IDD2P0 + 5

x4 66 69 72 mA

x8 71 74 77 mA

ICDD2P0 (slow exit) ICDD2P0 =

IDD2P0 + IDD2P0

x4, x8 16 16 16 mA

ICDD2P1 (fast exit) ICDD2P1 =

IDD2P1 + IDD2P0

x4, x8 20 22 24 mA

ICDD2Q ICDD2Q =

IDD2Q + IDD2P0

x4, x8 30 32 34 mA

ICDD2N ICDD2N =

IDD2N + IDD2P0

x4, x8 30 32 34 mA

ICDD2N T ICDD2NT =

IDD2NT + IDD2P0

x4, x8 34 36 38 mA

ICDD3P ICDD3P = IDD3P +

IDD2P0

x4, x8 32 34 36 mA

ICDD3N ICDD3N =

IDD3N + IDD2P0

x4, x8 36 38 40 mA

ICDD4R ICDD4RCDD4R =

IDD4R + IDD2P0 + 5

x4 88 98 108 mA

x8 98 108 118

ICDD4W ICDD4W =

IDD4W + IDD2P0 + 5

x4 88 98 108 mA

x8 98 108 118

ICDD5B ICDD5B =

IDD5B + IDD2P0

x4, x8 178 183 188 mA

ICDD6 ICDD6 =

IDD6 + IDD6

x4, x8 24 24 24 mA

ICDD6ET ICDD6ET =

IDD6ET + IDD6ET

x4, x8 32 32 32 mA

ICDD7 ICDD7 =

IDD7 + IDD2P0 + 5

x4, x8 133 143 153 mA

ICDD8 ICDD8 = 2 × IDD2P0 + 4 x4, x8 20 20 20 mA

Note: 1. ICDD values reflect the combined current of both individual die. IDDx represents individu-

al die values.

8Gb: x4, x8 TwinDie DDR3L SDRAM

Electrical Specifications – ICDD Parameters

CCMTD-1725822587-9746

DDR3L_8Gb_x4_x8_2CS_TwinDie_V90B.pdf - Rev. K 8/18 EN 12 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Table 9: DDR3L ICDD Specifications and Conditions (Rev P)

Note 1 applies to the entire table

Combined

Symbol

Individual

Die Status

Bus

Width -125 -107 -093 Units

ICDD0 ICDD0 =

IDD0 + IDD2P0+ 5

x4, x8 43 45 48 mA

ICDD1 ICDD1 =

IDD1 + IDD2P0 + 5

x4, x8 58 60 64 mA

ICDD2P0 (slow exit) ICDD2P0 =

IDD2P0 + IDD2P0

x4, x8 20 22 24 mA

ICDD2P1 (fast exit) ICDD2P1 =

IDD2P1 + IDD2P0

x4, x8 21 22 25 mA

ICDD2Q ICDD2Q =

IDD2Q + IDD2P0

x4, x8 25 26 29 mA

ICDD2N ICDD2N =

IDD2N + IDD2P0

x4, x8 26 28 34 mA

ICDD2N T ICDD2NT =

IDD2NT + IDD2P0

x4, x8 30 33 39 mA

ICDD3P ICDD3P = IDD3P +

IDD2P0

x4, x8 25 26 29 mA

ICDD3N ICDD3N =

IDD3N + IDD2P0

x4, x8 30 32 35 mA

ICDD4R ICDD4RCDD4R =

IDD4R + IDD2P0 + 5

x4, x8 105 106 127 mA

ICDD4W ICDD4W =

IDD4W + IDD2P0 + 5

x4, x8 105 106 127 mA

ICDD5B ICDD5B =

IDD5B + IDD2P0

x4, x8 160 163 172 mA

ICDD6 ICDD6 =

IDD6 + IDD6

x4, x8 30 30 30 mA

ICDD6ET ICDD6ET =

IDD6ET + IDD6ET

x4, x8 46 46 46 mA

ICDD7 ICDD7 =

IDD7 + IDD2P0 + 5

x4, x8 145 162 167 mA

ICDD8 ICDD8 = 2 × IDD2P0 + 4 x4, x8 24 26 30 mA

Note: 1. ICDD values reflect the combined current of both individual die. IDDx represents individu-

al die values.

8Gb: x4, x8 TwinDie DDR3L SDRAM

Electrical Specifications – ICDD Parameters

CCMTD-1725822587-9746

DDR3L_8Gb_x4_x8_2CS_TwinDie_V90B.pdf - Rev. K 8/18 EN 13 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Package Dimensions

Figure 5: 78-Ball FBGA Die Rev. E (package code TRF)

Seating plane

0.12 A

123789

Ball A1 ID

(covered by SR)

Ball A1 ID

0.3 ±0.05

1.1 ±0.1

6.4 CTR

9.5 ±0.1

0.8 TYP

9.6 CTR

11.5 ±0.1

78X Ø0.45

Dimensions apply

to solder balls

post-reflow

on Ø0.33 NSMD

ball pads.

0.8 TYP

Notes: 1. All dimensions are in millimeters.

2. Solder ball material: SAC305 (96.5% Sn, 3% Ag, 0.5% Cu).

8Gb: x4, x8 TwinDie DDR3L SDRAM

Package Dimensions

CCMTD-1725822587-9746

DDR3L_8Gb_x4_x8_2CS_TwinDie_V90B.pdf - Rev. K 8/18 EN 14 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Figure 6: 78-Ball FBGA Die Rev. N, P (package code RKB)

Seating plane

0.12 A

Ball A1 ID

(covered by SR)

Ball A1 ID

0.3 ±0.05

1.1 ±0.1

6.4 CTR

8 ±0.1

0.8 TYP

9.6 CTR

10.5 ±0.1

0.8 TYP

78X Ø0.45

Dimensions apply

to solder balls post-

reflow on Ø0.33

NSMD ball pads. 123789

Notes: 1. All dimensions are in millimeters.

2. Solder ball material: SAC305 (96.5% Sn, 3% Ag, 0.5% Cu).

8000 S. Federal Way, P.O. Box 6, Boise, ID 83707-0006, Tel: 208-368-4000

www.micron.com/products/support Sales inquiries: 800-932-4992

Micron and the Micron logo are trademarks of Micron Technology, Inc. TwinDie is a trademark of Micron Technology, Inc.

All other trademarks are the property of their respective owners.

This data sheet contains minimum and maximum limits specified over the power supply and temperature range set forth herein.

Although considered final, these specifications are subject to change, as further product development and data characterization some-

times occur.

8Gb: x4, x8 TwinDie DDR3L SDRAM

Package Dimensions

CCMTD-1725822587-9746

DDR3L_8Gb_x4_x8_2CS_TwinDie_V90B.pdf - Rev. K 8/18 EN 15 Micron Technology, Inc. reserves the right to change products or specifications without notice.