POWER LPQ142 Series 145 Watts Data Sheet Total Power: 110 - 145 Watts Input Voltage:85 - 264 Vac 120 - 300 Vdc # of Outputs:Quad SPECIAL FEATURES Active power factor correction IEC EN61000-3-2 compliance Adjustable outputs on 1, 3 & 4 Remote sense on main output Single wire current sharing Power fail and remote inhibit Built-in EMI filter Low output ripple Overvoltage protection Overload protection Thermal overload protection Adjustable floating 4th output RoHS compliant Optional cover (-C suffix) Optional fan cover (-CF suffix) SAFETY VDE UL CB CSA CE NEMKO 60950 60950 Certificate and report 60950 Mark (LVD) EN 60950/EMKO-TUE Electrical Specifications Input Input range 85 - 264 Vac; 120 - 300 Vdc Frequency 47 - 67 Hz Inrush current 38 A max, cold start @ 25 C Efficiency 75% typical at full load EMI filter Meets FCC Class B conducted CISPR 22 Class B conducted EN55022 Class B conducted VDE 0878 PT3 Class B conducted Power factor 0.99 typical Safety ground leakage current 1.0 mA @ 50/60 Hz, 264 Vac input Output Maximum power 80 W convection (60 W with cover -C) 145 W with 30 CFM forced air (100 W with cover -C) Adjustment range 3.3 - 5.5V on main; -12 - 15V on 3rd output 3.3 - 25 V on 4th output Hold-up time 20 ms @175 W load at nominal line Overload protection Short circuit protection on all outputs. Case overload protected @ 110-145% above peak rating Overvoltage protection Tracks outputs 1, 3 & 4; 10 to 35% LPQ142 Series Data Sheet Logic Control AC power failure TTL logic signal goes high 100 - 500 msec after V1 output; It goes low at least 4 msec before loss of regulation Remote inhibit Requires contact closure to inhibit outputs Remote sense Compensates for 0.5 V lead drop min. Will operate without remote sense connected. Reverse connection proteced. DC - OK TTL logic signal goes high after main output is in regulation. It goes low when there is a loss of regulation Environmental Specifications Operating temperature 0 to 50 C ambient. Derate each output 2.5% per degree from 50 to 70 C (except for -C version). Storage temperature -40 C to +85 C Temperature coefficient 0.4% per C Electromagnetic susceptibility Designed to meet IE61000-4, -2, -3, -4, -5, -6, -8, -11, Level 3 Humidity Operating; non-condensing 5% to 95% Vibration Three orthogonal axes, sweep at 1 oct/min, 5 min. dwell at four major resonances 0.75G peak 5Hz to 500Hz, operational MTBF demonstrated >550,000 hours at full load and 25C ambient conditions Ordering Information Model Number Output Voltage Minimum Load Maximum Load with Convection Cooling Maximum Load with 30CFM Forced Air Peak Load 1 Regulation 2 Ripple P/P (PARD)3 LPQ142 5 V (3.3 - 5.5 V) 0A 12 A 25 A 27 A 2% 50 mV 12 V 0A 5A 6A 9A 3% 120 mV -12V (-12 -15 V) 0A 1A 1.5 A 2A 3% <1% 3.3-25 V 0.5 A 1.5 A 4.5 A 5A 3% <50mV or 1% 1. Peak current lasting <30 seconds with a maximum 10% duty cycle. 2. At 25 C including initial tolerance, line voltage, load currents and output voltages adjusted to factory settings. 3. Peak-to-peak with 20 MHz bandwidth and 10 F in parallel with a 0.1 F capacitor at rated line voltage and load ranges. 4. Fourth (4th) output adjustable 3.3 - 25 V factory set at 5 V. 5. *Minimum loads are required when output set below 5 Volts 6. Remote inhibit resets OVP latch 7. This product is a Component Power Supply and is only for inclusion by professional installers within other equipment and must not be operated as a standalone product. EMC compliance to appropriate standards must be verified at the system level. This product is for sale to OEMs and System Integrators, including through Distribution Channels. It is not intended for sale to End Users. Note: -C suffix added to the model number indicates cover option. -CF suffix added to the model number indicates fan cover option. Pin Assignments Pin Assignments Mating Connectors SK1 SK6 (SK1) AC Input SK2 SK4 PIN 1 Ground PIN 1 N/C PIN 3 PIN 5 Neutral PIN 2 DC OK Line PIN 3 N/C PIN 1 +12 V PIN 4 V1 SWP PIN 2 Common PIN 5 Common PIN 3 -12 V PIN 6 +V1 sense PIN 4 Common PIN 7 Sense common PIN 5 +5 V to +25 V (float) PIN 8 + inhibit PIN 6 Common (float) PIN 9 - inhibit TB-1 Common PIN 10 Power fail TB-2 +5 V Molex 09-50-8051 (USA Molex 09-91-0500 (UK) PINS: 08-58-0111 Molex 09-50-8061 (USA) (SK2) Aux DC Output Molex 09-91-0600 (UK) PINS: 08-58-0111 Molex 90142-0010 (USA) (SK6) Control PINS: 90119-2110 or Signals Amp: 87977-3 PINS: 87309-8 (SK4) Main Output Molex BB-19141-0058 Artesyn Embedded Technologies connector kit #70-841-017, includes all of the above. Mechanical Drawing V1 Adj MAIN OUTPUT V4 Adj - Course V4 Adj - Fine 6 V4V4+ COMM -12V OUT COMM +12V OUT SK2 L 1 N 5 GND 10 SK1 6 1 SK6 V3 Output Adjust Pot -CF option M3 #6-32 (3X) 19.1 29.1 1.5 (38.1) M3 (2X) 6.4 161.5 #6-32 171.5 4.00 (101.6) (4X) (2X) (2X) 119.6 139.7 7.0 (177.8) M3 (8 places) 63.5 #6-32 (8 places) Notes: 1. Specifications subject to change without notice. 2. All dimensions in inches (mm), tolerance is 0.02". 3. Specifications are for convection rating at factory settings unless otherwise stated. 4. Mounting screw maximum insertion depth is 0.12". 5. Warranty: 2 year 6. Weight: 1.63 lb/0.74 kg WORLDWIDE OFFICES Americas Europe (UK) Asia (HK) 2900 S.Diablo Way Tempe, AZ 85282 USA +1 888 412 7832 Waterfront Business Park Merry Hill, Dudley West Midlands, DY5 1LX United Kingdom +44 (0) 1384 842 211 14/F, Lu Plaza 2 Wing Yip Street Kwun Tong, Kowloon Hong Kong +852 2176 3333 Artesyn Embedded Technologies, Artesyn and the Artesyn Embedded Technologies logo are trademarks and service marks of Artesyn Embedded Technologies, Inc. All other names and logos referred to are trade names, trademarks, or registered trademarks of their respective owners. (c) 2016 Artesyn Embedded Technologies, Inc. All rights reserved. For full legal terms and conditions, please visit www.artesyn.com/legal. www.artesyn.com For more information: www.artesyn.com/power For support: productsupport.ep@artesyn.com LPQ142 Series-DS 18Mar2016