49
01.10
D
Polyester (PET) Film and Foil
Capacitors for Pulse Applications
PCM 7.5 mm to 15 mm
Special Features Electrical Data
WIMA FKS 3
˜ Pulse duty construction
˜ According to RoHS 2002/95/EC
Typical Applications
For general DC-applications e.g.
˜ Coupling
˜ Decoupling
Construction
Dielectric:
Polyethylene-terephthalate (PET) film
Capacitor electrodes:
Metal foil
Internal construction:
Plastic film
Metal foil electrode
Terminating wire
Encapsulation:
Solvent-resistant, flame-retardant plastic
case with epoxy resin seal, UL 94 V-0
Terminations:
Tinned wire.
Marking:
Colour: Red. Marking: Black.
Epoxy resin seal: Yellow.
Capacitance range:
1000 pF to 0.22 mF (E12-values on request)
Rated voltages:
100 VDC, 250 VDC, 400 VDC, 630 VDC
Capacitance tolerances:
± 20%, ±10%, ±5%,
Operating temperature range:
–55+ C to +100+ C
Test specifications:
In accordance with IEC 60384-11
and EN 130 100
Climatic test category:
55/100/56 in accordance with IEC
Insulation resistance at +20+ C:
3 x 104 M¸
(mean value: 5 x 105 M¸)
Measuring voltage: 100 V/1 min.
Test voltage: 2 Ur, 2 sec.
Maximum pulse rise time:
1000 V/msec for pulses equal to the
rated voltage
Dissipation factors at +20+ C: tan d
at f
C0.01mF
0.01 mFPC0.22 mF
1 kHz 8 x 10-3 8 x 10-3
10 kHz 15 x 10-3 20 x 10-3
100 kHz 20 x 10-3 25 x 10-3
Voltage derating:
A voltage derating factor of 1.25 % per K
must be applied from +85+ C for DC
voltages and from +75+ C for AC
voltages.
Reliability:
Operational life 300 000 hours
Failure rate P 5 fit (0.5 x Ur and 40+ C)
Mechanical Tests
Pull test on leads:
10 N in direction of leads according to
IEC 60068-2-21
Vibration:
6 hours at 10 ... 2000 Hz and 0.75 mm
displacement amplitude or 10 g in
accordance with IEC 60068-2-6
Low air density:
1kPa = 10 mbar in accordance with
IEC 60068-2-13
Bump test:
4000 bumps at 390 m/sec2 in
accordance with IEC 60068-2-29
Packing
Available taped and reeled.
Detailed taping information and graphs
at the end of the catalogue.
For further details and graphs please
refer to Technical Information.
50
01.10
Continuation
General Data
D
Capacitance 100 VDC/63 VAC* 250 VDC/160 VAC*
W H L PCM** Part number W H L PCM** Part number
1000 pF 3 8.5 10 7.5 FKS3D011002B00_ _ _ _ 3 8.5 10 7.5 FKS3F011002B00_ _ _ _
1500 „ 3 8.5 10 7.5 FKS3D011502B00_ _ _ _ 3 8.5 10 7.5 FKS3F011502B00_ _ _ _
2200 „ 3 8.5 10 7.5 FKS3D012202B00_ _ _ _ 3 8.5 10 7.5 FKS3F012202B00_ _ _ _
3300 „ 3 8.5 10 7.5 FKS3D013302B00_ _ _ _ 3 8.5 10 7.5 FKS3F013302B00_ _ _ _
4700 „ 3 8.5 10 7.5 FKS3D014702B00_ _ _ _ 3 8.5 10 7.5 FKS3F014702B00_ _ _ _
3 9 13 10 FKS3F014703A00_ _ _ _
6800 „ 3 8.5 10 7.5 FKS3D016802B00_ _ _ _ 3 8.5 10 7.5 FKS3F016802B00_ _ _ _
3 9 13 10 FKS3F016803A00_ _ _ _
0.01 mF 3 8.5 10 7.5 FKS3D021002B00_ _ _ _ 3 9 13 10 FKS3F021003A00_ _ _ _
3 9 13 10 FKS3D021003A00_ _ _ _
0.015 „ 3 8.5 10 7.5 FKS3D021502B00_ _ _ _ 4 9.5 13 10 FKS3F021503D00_ _ _ _
3 9 13 10 FKS3D021503A00_ _ _ _
0.022 „ 3 8.5 10 7.5 FKS3D022202B00_ _ _ _ 5 11 13 10 FKS3F022203F00_ _ _ _
3 9 13 10 FKS3D022203A00_ _ _ _
0.033 „ 4 9.5 13 10 FKS3D023303D00_ _ _ _ 6 12 13 10 FKS3F023303G00_ _ _ _
0.047 „ 4 9.5 13 10 FKS3D024703D00_ _ _ _ 6 12.5 18 15 FKS3F024704C00_ _ _ _
0.068 „ 5 11 13 10 FKS3D026803F00_ _ _ _ 7 14 18 15 FKS3F026804D00_ _ _ _
0.1 mF 6 12 13 10 FKS3D031003G00_ _ _ _ 8 15 18 15 FKS3F031004F00_ _ _ _
0.15 „ 7 14 18 15 FKS3D031504D00_ _ _ _ 9 16 18 15 FKS3F031504J00_ _ _ _
0.22 „ 8 15 18 15 FKS3D032204F00_ _ _ _
Capacitance 400 VDC/250 VAC* 630 VDC/300 VAC*
W H L PCM** Part number W H L PCM** Part number
1000 pF 3 9 13 10 FKS3G011003A00_ _ _ _ 3 9 13 10 FKS3J011003A00_ _ _ _
1500 „ 3 9 13 10 FKS3G011503A00_ _ _ _ 3 9 13 10 FKS3J011503A00_ _ _ _
2200 „ 3 9 13 10 FKS3G012203A00_ _ _ _ 3 9 13 10 FKS3J012203A00_ _ _ _
3300 „ 3 9 13 10 FKS3G013303A00_ _ _ _ 4 9.5 13 10 FKS3J013303D00_ _ _ _
4700 „ 3 9 13 10 FKS3G014703A00_ _ _ _ 4 9.5 13 10 FKS3J014703D00_ _ _ _
6800 „ 3 9 13 10 FKS3G016803A00_ _ _ _ 5 11 13 10 FKS3J016803F00_ _ _ _
0.01 mF 4 9.5 13 10 FKS3G021003D00_ _ _ _ 6 12 13 10 FKS3J021003G00_ _ _ _
0.015 „ 5 11 13 10 FKS3G021503F00_ _ _ _ 6 12.5 18 15 FKS3J021504C00_ _ _ _
0.022 „ 6 12 13 10 FKS3G022203G00_ _ _ _ 7 14 18 15 FKS3J022204D00_ _ _ _
0.033 „ 6 12.5 18 15 FKS3G023304C00_ _ _ _ 8 15 18 15 FKS3J023304F00_ _ _ _
0.047 „ 7 14 18 15 FKS3G024704D00_ _ _ _
0.068 „ 8 15 18 15 FKS3G026804F00_ _ _ _
0.1 mF 9 16 18 15 FKS3G031004J00_ _ _ _
* AC voltage: f = 50 Hz; 1.4 x U
rms
+ UDC U
r
** PCM = Printed circuit module = lead spacing
Dims. in mm.
Rights reserved to amend design data without prior notification.
d = 0.5 P if W = 3
d = 0.6 P if W 4 PCM 7.5 and 10
d = 0.8 P if PCM = 15
PCM
at the lead exit points
( 0.4)
L
W
H
d
6-2
WIMA FKS 3
Part number completion:
Tolerance: 20 % = M
10 % = K
5 % = J
Packing: bulk = S
Lead length: 6-2 = SD
Taped version see page 140.
AC voltage graphs see page 53
53
01.10
D
Permissible AC voltage
in relation to frequency
at 10) C internal temperature rise
(general guide).
Permissible AC voltage
in relation to frequency
at 10) C internal temperature rise
(general guide).
WIMA FKS 3
Technical information and general data see page 49.
Continuation
WIMA FKM 3
Continuation
16
01.10
D
Recommendation for Processing
and Application of
Through-Hole Capacitors
Soldering Process
A preheating of through-hole WIMA
capacitors is allowed for temperatures
Tmax P 100 ° C.
In practice a preheating duration of
t P 5 min. has been proven to be best.
Single wave soldering
Soldering bath temperature: T P 260 ° C
Immersion time: t P 5 sec
Double wave soldering
Soldering bath temperature: T P 260 ° C
Immersion time: 2 x t P 3 sec
Due to different soldering processes and
heat requirements the graphs are to be
regarded as a recommendation only.
2 s 3 s
30 60 90 120 150 180 210 240 sec][
t
T
260
240
220
200
180
160
140
120
100
80
60
40
20
[°C] 10 s
see detail-
enlargement
Wave soldering
Typical temperature/time graph for double wave soldering
WIMA Quality and Environmental Philosophy
ISO 9001:2000 Certification
ISO 9001:2000 is an international basic
standard of quality assurance systems for
all branches of industry. The approval
according to ISO 9001:2000 of our
factories by the VDE inspectorate certifies
that organisation, equipment and moni-
toring of quality assurance in our factories
correspond to internationally recognized
standards.
WIMA WPCS
The WIMA Process Control System (WPCS)
is a quality surveillance and optimization
system developed by WIMA. WPCS is a
major part of the quality-oriented WIMA
production. Points of application of WPCS
during production process:
” incoming material inspection
” metallization
” film inspection
” schoopage
” pre-healing
” lead attachment
” cast resin preparation/
encapsulation
” 100% final inspection
” AQL check
WIMA Environmental Policy
All WIMA capacitors, irrespective of
whether through-hole devices or SMD,
are made of environmentally friendly
materials. Neither during manufacture
nor in the product itself any toxic
substances are used, e.g.
– Lead – PBB/PBDE
– PCB – Arsenic
– CFC – Cadmium
– Hydrocarbon chloride – Mercury
– Chromium 6+ – etc.
We merely use pure, recyclable materials
for packing our components, such as:
” carton
” cardboard
” adhesive tape made of paper
” polystyrene
We almost completely refrain from using
packing materials such as:
” foamed polystyrene (Styropor®)
” adhesive tapes made of plastic
” metal clips
RoHS Compliance
According to the RoHS Directive 2002/95/EC
certain hazardous substances like e.g. lead,
cadmium, mercury must not be used any
longer in electronic equipment as of July 1st,
2006. For the sake of the environment WIMA
has refraind from using such substances since
years already.
Tape for lead-free WIMA capacitors
DIN EN ISO 14001:2005
WIMA’s environmental management has
been established in accordance with the
guidelines of DIN EN ISO 14001:2005.
The certification has been granted in
June 2006.
140
01.10
D
P
P1
P0
P2
F
d
P
P1
H1
H
P0
d
P2
F
t
D0
W2
Vh
W0
P1
P2
P0
P
H1
H
W
1
W
d
F
Diagram 1:
PCM 2.5/5/7.5mm
Diagram 3: PCM 22.5 and 27.5*mm
*PCM 27.5 taping possible with two feed holes between components
Diagram 2: PCM 10/15 mm
Dimensions for Radial Taping
Designation Symbol PCM 2.5 taping PCM 5 taping PCM 7.5 taping PCM 10 taping* PCM 15 taping* PCM 22.5 taping PCM 27.5 taping
Carrier tape width W 18.0
p0.5
18.0
p0.5
18.0
p0.5
18.0
p0.5
18.0
p0.5
18.0
p0.5
18.0
p0.5
Hold-down tape width W
0
6.0 for hot-sealing 6.0 for hot-sealing 12.0 for hot-sealing 12.0 for hot-sealing 12.0 for hot-sealing 12.0 for hot-sealing 12.0 for hot-sealing
adhesive tape adhesive tape adhesive tape adhesive tape adhesive tape adhesive tape adhesive tape
Hole position W
1
9.0
p0.5
9.0
p0.5
9.0
p0.5
9.0
p0.5
9.0
p0.5
9.0
p0.5
9.0
p0.5
Hold-down tape position W
2
0.5 to 3.0 max. 0.5 to 3.0 max. 0.5 to 3.0 max. 0.5 to 3.0 max. 0.5 to 3.0 max. 0.5 to 3.0 max. 0.5 to 3.0 max.
Feed hole diameter D
0
4.0
p0.2
4.0
p0.2
4.0
p0.2
4.0
p0.2
4.0
p0.2
4.0
p0.2
4.0
p0.2
Pitch of component P 12.7
p1.0
12.7
p1.0
12.7
p1.0
25.4
p1.0
25.4
p1.0
38.1
p1.5
3
*8.1
p1.5
or 50.8
p1.5
cumulative pitch
cumulative pitch
cumulative pitch
cumulative pitch
cumulative pitch
cumulative pitch
cumulative pitch
Feed hole pitch P
0
12.7
p0.3 error max.
12.7
p0.3 error max.
12.7
p0.3 error max.
12.7
p0.3 error max.
12.7
p0.3 error max.
12.7
p0.3 error max.
12.7
p0.3 error max.
1.0 mm/20 pitch
1.0 mm/20 pitch
1.0 mm/20 pitch
1.0 mm/20 pitch
1.0 mm/20 pitch
1.0 mm/20 pitch
1.0 mm/20 pitch
Feed hole centre P
1
5.1
p0.5
3.85
p0.7
2.6
p0.7
7.7
p0.7
5.2
p0.7
7.8
p0.7
5.3
p0.7
to lead
Hole centre to P
2
6.35
p1.3
6.35
p1.3
6.35
p1.3
12.7
p1.3
12.7
p1.3
19.05
p1.3
19.05
p1.3
component centre
Feed hole centre to bottom H 16.5
p0.3
16.5
p0.3
16.5
p0.5
16.5
p0.5
16.5
p0.5
16.5
p0.5
16.5
p0.5
edge of the component 18.5
p0.5
18.5
p0.5
18.5
p0.5
18.5
p0.5
18.5
p0.5
18.5
p0.5
18.5
p0.5
Feed hole centre to top H
1
H+H
component
< H
1
H+H
component
< H
1
H+H
component
< H
1
H+H
component
< H
1
H+H
component
< H
1
H+H
component
< H
1
H+H
component
< H
1
edge of the component 32.25 max. 32.25 max. 24.5 to 31.5 25.0 to 31.5 26.0 to 37.0 30.0 to 43.0 35.0 to 45.0
Lead spacing at F 2.5
p0.5
5.0
+0.8
7.5
p0.8
10.0
p0.8
15
p0.8
22.5
p0.8
27.5
p0.8
upper edge of carrier tape
–0.2
Lead diameter d 0.4
p0.05
0.5
p0.05
„
0.5
p0.05
or
0.6
–0.05
„
0.5
p0.05
or
0.6
–0.05
0.8
–0.05
0.8
–0.05
0.8
–0.05
Component alignment Dh p 2.0 max. p 2.0 max. p 3.0 max. p 3.0 max. p 3.0 max. p 3.0 max. p 3.0 max.
Total tape thickness t 0.7
p0.2
0.7
p0.2
0.7
p0.2
0.7
p0.2
0.7
p0.2
0.7
p0.2
0.7
p0.2
ROLL/AMMO AMMO
Package
(see also page 141)
Unit see details page 143.
Dims in mm.
„ Diameter of leads see General Data. Please clarify customer-specific deviations with the manufacturer.
* PCM 10 and PCM 15 can be crimped to PCM 7.5.
Position of components according to PCM 7.5 (sketch 1). P0 = 12.7 or 15.0 is possible
REEL
P 360 max.
B
52 p2 depending on
P 30 p1 58 p2 comp. dimensions
52 p2 54 p2 depending
REEL
P 360 max. B 58 p2
or
REEL
P 500 max. B 60 p2 on PCM and
P 30 p1 66 p2 P 25 p1 68 p2 component dimensions
+0.06 +0,06 +0,08 +0,08 +0.08
Typical Dimensions for
Taping Configuration
142
01.10
D
Rights reserved to amend design data without prior notification. Moulded versions. * Tray-Packing-System
Samples and pre-production needs on request.
Packing Quantities for Bulk Capacitors and TPS*
PCM Size pcs. per packaging unit bulk pcs. per packaging unit/TPS*
Mini Standard Maxi Mini Standard
Part number codes W H L M S G X Y
2.5 mm
2.5 7 4.6 1000 5000 10 000 – –
3 7.5 4.6 1000 5000 10 000 – –
3.8 8.5 4.6 1000 5000 10 000 – –
4.6 9 4.6 1000 5000 10 000 – –
5.5 10 4.6 1000 5000 10 000 – –
5 mm
2.5 6.5 7.2 2000 5000 10 000 – –
3 7.5 7.2 1000 5000 – – –
3.5 8.5 7.2 1000 5000 – – –
4.5 6 7.2 1000 6000 – – –
4.5 9.5 7.2 1000 4000 – – –
5 10 7.2 1000 3500 – – –
5.5 7 7.2 1000 4000 – – –
5.5 11.5 7.2 500 2500 – – –
6.5 8 7.2 1000 2500 – – –
7.2 8.5 7.2 500 2500 – – –
7.2 13 7.2 500 2000 – – –
8.5 10 7.2 500 2000 – – –
8.5 14 7.2 500 1500 – – –
11 16 7.2 250 1000 – – –
7.5 mm
2.5 7 10 1000 5000 – – –
3 8.5 10 1000 5000 – – –
4 9 10 1000 4000 – – –
4.5 9.5 10.3 1000 3500 – – –
5 10.5 10.3 1000 3000 – – –
5.7 12.5 10.3 500 2000 – – –
7.2 12.5 10.3 500 1500 – – –
10 mm
3 9 13 1000 3000 – – –
4 8.5 13.5 500 3000 – – –
4 9 13 1000 3000 – – –
4 9.5 13 1000 3000 – – –
5 10 13.5 500 2000 – – –
5 11 13 1000 3000 – – –
6 12 13 800 2400 – – –
6 12.5 13 800 2400 – – –
8 12 13 500 2000 – – –
15 mm
5 11 18 800 2400 – – –
5 13 19 200 1000 – –
6 12.5 18 500 2000 – – –
6 14 19 250 1000 – –
7 14 18 400 1600 – – –
7 15 19 250 1000 – –
8 15 18 400 1200 – – –
8 17 19 100 500 – –
9 14 18 400 1200 – – –
9 16 18 300 900 – – –
10 18 19 100 500 – – –
11 14 18 300 1000 – – –
22.5 mm
5 14 26.5 300 1200 – – –
6 15 26.5 250 1000 – – –
7 16.5 26.5 190 760 – – –
8 20 28 – – – 115 690
8.5 18.5 26.5 – – – 220 880
10 22 28 – – – 90 540
10.5 19 26.5 – – – 170 680
10.5 20.5 26.5 – – – 170 680
11 21 26.5 – – – 170 680
12 24 28 – – – 75 450
27.5 mm
9 19 31.5 – – – 160 640
11 21 31.5 – – – 136 544
13 24 31.5 – – – 112 448
13 25 33 – – – 56 336
15 26 31.5 – – – 96 384
15 26 33 – – – 48 288
17 29 31.5 – – – 88 176
17 34.5 31.5 – – – 88 176
20 32 33 – – – 36 216
20 39.5 31.5 – – – 36 144
37.5 mm
9 19 41.5 – – – 60 480
11 22 41.5 – – – 51 408
13 24 41.5 – – – 84 252
15 26 41.5 – – – 72 144
17 29 41.5 – – – 66 132
19 32 41.5 – – – 54 108
20 39.5 41.5 – – – 27 108
24 45.5 41.5 – – – 21 84
143
01.10
D
* for 2-inch transport pitches. Moulded versions. Rights reserved to amend design data without prior notification.
Samples and pre-production needs 1 packing unit minimum.
PCM Size
ROLL REEL AMMO
P 360 P 500 340 x 340 490 x 370
H16.5 H18.5 H16.5 H18.5 H16.5 H18.5 H16.5 H18.5 H16.5 H18.5
Part number codes W H L N O F I H J A C B D
2.5 mm
2.5 7 4.6 2200 2500 – 2800 –
3 7.5 4.6 2000 2300 – 2300 –
3.8 8.5 4.6 1500 1800 – 1800 –
4.6 9 4.6 1200 1500 – 1500 –
5.5 10 4.6 900 1200 – 1200 –
5 mm
2.5 6.5 7.2 2200 2500 – 2800 –
3 7.5 7.2 2000 2300 – 2300 –
3.5 8.5 7.2 1600 2000 – 2000 –
4.5 6 7.2 1300 1500 – 1500 –
4.5 9.5 7.2 1300 1500 – 1500 –
5 10 7.2 1100 1400 – 1400 –
5.5 7 7.2 1000 1200 – 1200 –
5.5 11.5 7.2 1000 1200 – 1200 –
6.5 8 7.2 800 1000 – 1000 –
7.2 8.5 7.2 700 1000 – 1000 –
7.2 13 7.2 700 950 – 1000 –
8.5 10 7.2 600 800 – 800 –
8.5 14 7.2 600 800 – 800 –
11 16 7.2 500 700 – 700 –
7.5 mm
2.5 7 10 – 2500 4400 2800 –
3 8.5 10 – 2200 4300 2300 4150
4 9 10 – 1700 3200 1700 3100
4.5 9.5 10.3 – 1500 2900 1400 2800
5 10.5 10.3 – 1300 2500 1300 –
5.7 12.5 10.3 – 1000 2200 1100 –
7.2 12.5 10.3 – 900 1800 1000 –
10 mm
3 9 13 – 1100 2200 – 1900
4 8.5 13.5 – 900 1600 – 1450
4 9 13 – 900 1600 – 1450
4 9.5 13 – 900 1600 – 1400
5 10 13.5 – 700 1300 – 1200
5 11 13 – 700 1300 – 1200
6 12 13 – 550 1100 – 1000
6 12.5 13 – 550 1100 – 1000
8 12 13 – 400 800 – 740
15 mm
5 11 18 – 600 1200 – 1150
5 13 19 – 600 1200 – 1200
6 12.5 18 – 500 1000 – 1000
6 14 19 – 500 1000 – 1000
7 14 18 – 450 900 – 850
7 15 19 – 450 900 – 850
8 15 18 – 400 800 – 740
8 17 19 – 400 800 – 740
9 14 18 – 350 700 – 650
9 16 18 – 350 700 – 650
10 18 19 – 300 650 – 590
11 14 18 – 300 600 – 540
22.5 mm
5 14 26.5 – – 800 – 770
6 15 26.5 – – 700 – 640
7 16.5 26.5 – – 600 – 550
8 20 28 – – 500 – 480
8.5 18.5 26.5 – – 480 – 450
10 22 28 – – 420 – 380
10.5 19 26.5 – – 400 – 360
10.5 20.5 26.5 – – 400 – 360
11 21 26.5 – – 380 – 350
12 24 28 – – 350 – 310
27.5 mm
9 19 31.5 – – 460/340* – 420
11 21 31.5 – – 380/280* – 350
13 24 31.5 – – 300 – 290
15 26 31.5 – – 270 – 250
Packing Units for Taped Capacitors
with Radial Leads
138
01.10
D
A WIMA part number consists of 18 digits and is composed as follows:
Field 1 - 4: Type description
Field 5 - 6: Rated voltage
Field 7 - 10: Capacitance
Field 11 - 12: Size and PCM
Field 13 - 14: Special features (e.g. Snubber versions)
Field 15: Capacitance tolerance
Field 16: Packing
Field 17 - 18: Lead length (untaped)
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
M K S 2 C 0 3 1 0 0 1 A 0 0 M S S D
MKS 2 63 VDC 0.01 mF 2.5 x 6.5 x 7.2 -20 %bulk 6 -2
WIMA Part Number System
The data on this page is not complete and serves only to explain the part number system. Part number information is listed on the
pages of the respective WIMA range.
Type description: Rated voltage: Capacitance: Size: Tolerance:
SMD-PET = SMDT 16 VDC = A0 22 pF = 0022 4.8 x 3.3 x 3 Size 1812 = X1 20 % = M
SMD-PEN = SMDN 2.5 VDC = A1 47 pF = 0047 5.7 x 5.1 x 3.5 Size 2220 = Y1 10 % = K
SMD-PPS = SMDI 4 VDC = A2 100 pF = 0100 7.2 x 6.1 x 3 Size 2824 = T1 5 % = J
FKP 02 = FKS0 14 VDC = A3 220 pF = 0220 2.5 x 7 x 4.6 PCM 2.5 = 0B 2.5 % = H
MKS 02 = MKS0 28 VDC = A4 470 pF = 0470 3 x 7.5 x 4.6 PCM 2.5 = 0C 1 % = E
FKS 2 = FKS2 40 VDC = A5 1000 pF = 1100 2.5 x 6.5 x 7.2 PCM 5 = 1A ...
FKM 2 = FKM2 50 VDC = B0 2200 pF = 1220 3 x 7.5 x 7.2 PCM 5 = 1B
FKP 2 = FKP2 63 VDC = C0 4700 pF = 1470 2.5 x 7 x 10 PCM 7.5 = 2A
MKS 2 = MKS2 100 VDC = D0 0.01 mF= 2100 3 x 8.5 x 10 PCM 7.5 = 2B Packing:
MKP 2 = MKP2 160 VDC = E0 0.022 mF= 2220 3 x 9 x 13 PCM 10 = 3A AMMO H16.5 340 x 340 = A
MKI 2 = MKI2 250 VDC = F0 0.047 mF= 2470 4 x 9 x 13 PCM 10 = 3B AMMO H16.5 490 x 370 = B
FKS 3 = FKS3 400 VDC = G0 0.1 mF= 3100 5 x 11 x 18 PCM 15 = 4A AMMO H18.5 340 x 340 = C
FKM 3 = FKM3 630 VDC = J0 0.22 mF= 3220 6 x 12.5 x 18 PCM 15 = 4B AMMO H18.5 490 x 370 = D
FKP 3 = FKP3 800 VDC = L0 0.47 mF= 3470 5 x 14 x 26.5 PCM 22.5 = 5A REEL H16.5 360 = F
MKS 4 = MKS4 850 VDC = M0 1 mF= 4100 6 x 15 x 26.5 PCM 22.5 = 5B REEL H16.5 500 = H
MKM 4 = MKM4 1000 VDC = O1 2.2 mF= 4220 9 x 19 x 31.5 PCM 27.5 = 6A REEL H18.5 360 = I
MKP 4 = MKP4 1200 VDC = Q0 4.7 mF= 4470 11 x21 x 31.5 PCM 27.5 = 6B REEL H18.5 500 = J
MKP 10 = MKP1 1600 VDC = T0 10 mF= 5100 9 x 19 x 41.5 PCM 37.5 = 7A ROLL H16.5 = N
FKP 4 = FKP4 2000 VDC = U0 22 mF= 5220 11 x 22 x 41.5 PCM 37.5 = 7B ROLL H18.5 = O
FKP 1 = FKP1 2500 VDC = V0 47 mF= 5470 94 x 49 x 182 DCH_ = H0 BLISTER W12 180 = P
MKP-X2 = MKX2 4000 VDC = X0 100 mF= 6100 94 x 77 x 182 DCH_ = H1 BLISTER W12 330 = Q
MKP-X2 R = MKXR 6000 VDC = Y0 220 mF= 6220 ... BLISTER W16 330 = R
MKP-Y2 = MKY2 250 VAC = 0W 1 F = A010 BLISTER W24 330 = T
MP 3-X2 = MPX2 275 VAC = 1W 2.5 F = A025 Bulk Mini = M
MP 3-X1 = MPX1 300 VAC = 2W 50 F = A500 Special features: Bulk Standard = S
MP 3-Y2 = MPY2 400 VAC = 3W 100 F = B100 Standard = 00 Bulk Maxi = G
MP 3R-Y2 = MPYR 440 VAC = 4W 600 F = B600 Version A1 = 1A TPS Mini = X
Snubber FKP = SNFP 500 VAC = 5W 1200 F = C120 Version A1.1 = 1B TPS Standard = Y
Snubber MKP = SNMP ... ... ... ...
GTO MKP = GTOM
DC-LINK MKP 4 = DCP4
DC-LINK MKP C = DCPC Lead length (untaped)
DC-LINK HC = DCH_ 3.5 ±0.5 = C9
SuperCap C = SCSC 6 -2 = SD
SuperCap MC = SCMC 16 -1 = P4
SuperCap R = SCSR ...
SuperCap MR = SCMR
