D WIMA FKS 3 Polyester (PET) Film and Foil Capacitors for Pulse Applications PCM 7.5 mm to 15 mm Special Features Electrical Data Pulse duty construction According to RoHS 2002/95/EC Typical Applications For general DC-applications e.g. Coupling Decoupling Construction Dielectric: Polyethylene-terephthalate (PET) film Capacitor electrodes: Metal foil Internal construction: Plastic film Metal foil electrode Capacitance range: 1000 pF to 0.22 mF (E12-values on request) Rated voltages: 100 VDC, 250 VDC, 400 VDC, 630 VDC Capacitance tolerances: 20%, 10%, 5%, Operating temperature range: -55+ C to +100+ C Test specifications: In accordance with IEC 60384-11 and EN 130 100 Climatic test category: 55/100/56 in accordance with IEC Insulation resistance at +20+ C: 3 x 104 M (mean value: 5 x 10 5 M) Measuring voltage: 100 V/1 min. Test voltage: 2 U r, 2 sec. Maximum pulse rise time: 1000 V/ msec for pulses equal to the rated voltage Dissipation factors at +20+ C: tan d at f C0.01mF 0.01 mFPC0.22 mF 1 kHz 8 x 10-3 10 kHz 15 x 10-3 100 kHz 20 x 10-3 8 x 10-3 20 x 10-3 25 x 10-3 Voltage derating: A voltage derating factor of 1.25 % per K must be applied from +85+ C for DC voltages and from +75+ C for AC voltages. Reliability: Operational life 300 000 hours Failure rate 5 fit (0.5 x U r and 40+ C) Terminating wire Mechanical Tests Pull test on leads: 10 N in direction of leads according to IEC 60068-2-21 Vibration: 6 hours at 10 ... 2000 Hz and 0.75 mm displacement amplitude or 10 g in accordance with IEC 60068-2-6 Low air density: 1kPa = 10 mbar in accordance with IEC 60068-2-13 Bump test: 4000 bumps at 390 m/sec 2 in accordance with IEC 60068-2-29 Packing Available taped and reeled. Detailed taping information and graphs at the end of the catalogue. For further details and graphs please refer to Technical Information. 01.10 Encapsulation: Solvent-resistant, flame-retardant plastic case with epoxy resin seal, UL 94 V-0 Terminations: Tinned wire. Marking: Colour: Red. Marking: Black. Epoxy resin seal: Yellow. 49 D WIMA FKS 3 Continuation General Data Capacitance W H 100 VDC/63 VAC* PCM** Part number L W H L 250 VDC/160 VAC* PCM** Part number 1000 pF 3 8.5 10 7.5 FKS3D011002B00_ _ _ _ 1500 3 8.5 10 7.5 FKS3D011502B00_ _ _ _ 2200 3 8.5 10 7.5 FKS3D012202B00_ _ _ _ 3300 3 8.5 10 7.5 FKS3D013302B00_ _ _ _ 4700 3 8.5 10 7.5 FKS3D014702B00_ _ _ _ 6800 3 8.5 10 7.5 FKS3D016802B00_ _ _ _ 3 8.5 3 8.5 3 8.5 3 8.5 3 8.5 3 9 3 8.5 3 9 10 7.5 10 7.5 10 7.5 10 7.5 10 7.5 13 10 10 7.5 13 10 0.01 0.015 0.022 0.033 0.047 0.068 3 9 13 10 FKS3F021003A00_ _ _ _ 4 9.5 13 10 FKS3F021503D00_ _ _ _ 5 11 13 10 FKS3F022203F00_ _ _ _ 6 6 7 12 12.5 14 13 18 18 10 FKS3F023303G00_ _ _ _ 15 FKS3F024704C00_ _ _ _ 15 FKS3F026804D00_ _ _ _ 8 9 15 16 18 18 15 FKS3F031004F00_ _ _ _ 15 FKS3F031504J00_ _ _ _ W H L 3 8.5 3 9 3 8.5 3 9 3 8.5 3 9 4 9.5 4 9.5 5 11 10 7.5 13 10 10 7.5 13 10 10 7.5 13 10 13 10 13 10 13 10 0.1 mF 0.15 0.22 6 7 8 12 14 15 13 18 18 Capacitance W H L mF FKS3D021002B00_ _ _ _ FKS3D021003A00_ _ _ _ FKS3D021502B00_ _ _ _ FKS3D021503A00_ _ _ _ FKS3D022202B00_ _ _ _ FKS3D022203A00_ _ _ _ FKS3D023303D00_ _ _ _ FKS3D024703D00_ _ _ _ FKS3D026803F00_ _ _ _ 10 FKS3D031003G00_ _ _ _ 15 FKS3D031504D00_ _ _ _ 15 FKS3D032204F00_ _ _ _ 400 VDC/250 VAC* PCM** Part number FKS3F011002B00_ _ _ _ FKS3F011502B00_ _ _ _ FKS3F012202B00_ _ _ _ FKS3F013302B00_ _ _ _ FKS3F014702B00_ _ _ _ FKS3F014703A00_ _ _ _ FKS3F016802B00_ _ _ _ FKS3F016803A00_ _ _ _ 630 VDC/300 VAC* PCM** Part number 1000 1500 2200 3300 4700 6800 pF 3 9 3 9 3 9 3 9 3 9 3 9 13 13 13 13 13 13 10 10 10 10 10 10 FKS3G011003A00_ _ _ _ FKS3G011503A00_ _ _ _ FKS3G012203A00_ _ _ _ FKS3G013303A00_ _ _ _ FKS3G014703A00_ _ _ _ FKS3G016803A00_ _ _ _ 3 9 3 9 3 9 4 9.5 4 9.5 5 11 13 13 13 13 13 13 10 10 10 10 10 10 FKS3J011003A00_ _ _ _ FKS3J011503A00_ _ _ _ FKS3J012203A00_ _ _ _ FKS3J013303D00_ _ _ _ FKS3J014703D00_ _ _ _ FKS3J016803F00_ _ _ _ 0.01 0.015 0.022 0.033 0.047 0.068 mF 4 9.5 5 11 6 12 6 12.5 7 14 8 15 13 13 13 18 18 18 10 10 10 15 15 15 FKS3G021003D00_ _ _ _ FKS3G021503F00_ _ _ _ FKS3G022203G00_ _ _ _ FKS3G023304C00_ _ _ _ FKS3G024704D00_ _ _ _ FKS3G026804F00_ _ _ _ 6 6 7 8 13 18 18 18 10 15 15 15 FKS3J021003G00_ _ _ _ FKS3J021504C00_ _ _ _ FKS3J022204D00_ _ _ _ FKS3J023304F00_ _ _ _ 9 18 15 FKS3G031004J00_ _ _ _ 0.1 mF 16 12 12.5 14 15 * AC voltage: f = 50 Hz; 1.4 x U rms + UDC U r Part number completion: ** PCM = Printed circuit module = lead spacing W L Dims. in mm. H 6 -2 d PCM d = 0.5 P if W = 3 PCM 7.5 and 10 at the lead exit points d = 0.6 P if W 4 ( 0.4) d = 0.8 P if PCM = 15 Tolerance: 20 % = M 10 % = K 5 % = J Packing: bulk = S Lead length: 6-2 = SD Taped version see page 140. Rights reserved to amend design data without prior notification. 01.10 AC voltage graphs see page 53 50 WIMA FKM 3 D Continuation Permissible AC voltage in relation to frequency at 10) C internal temperature rise (general guide). WIMA FKS 3 01.10 Permissible AC voltage in relation to frequency at 10) C internal temperature rise (general guide). Technical information and general data see page 49. 53 D Recommendation for Processing and Application of Through-Hole Capacitors Soldering Process Wave soldering T A preheating of through-hole WIMA capacitors is allowed for temperatures T max P 100 C. In practice a preheating duration of t P 5 min. has been proven to be best. 260 240 220 200 180 160 140 120 100 80 60 40 20 Single wave soldering Soldering bath temperature: T P 260 C Immersion time: t P 5 sec Double wave soldering Soldering bath temperature: T P 260 C Immersion time: 2 x t P 3 sec Due to different soldering processes and heat requirements the graphs are to be regarded as a recommendation only. 10 s [C] see detailenlargement 2s 3s t 30 60 90 120 150 180 210 240 [sec] Typical temperature/time graph for double wave soldering WIMA Quality and Environmental Philosophy ISO 9001:2000 Certification ISO 9001:2000 is an international basic standard of quality assurance systems for all branches of industry. The approval according to ISO 9001:2000 of our factories by the VDE inspectorate certifies that organisation, equipment and monitoring of quality assurance in our factories correspond to internationally recognized standards. WIMA WPCS The WIMA Process Control System (WPCS) is a quality surveillance and optimization system developed by WIMA. WPCS is a major part of the quality-oriented WIMA production. Points of application of WPCS during production process: incoming material inspection metallization film inspection schoopage pre-healing lead attachment cast resin preparation/ encapsulation " 100% final inspection " AQL check All WIMA capacitors, irrespective of whether through-hole devices or SMD, are made of environmentally friendly materials. Neither during manufacture nor in the product itself any toxic substances are used, e.g. - - - - - Lead PCB CFC Hydrocarbon chloride Chromium 6+ - - - - - PBB/PBDE Arsenic Cadmium Mercury etc. RoHS Compliance According to the RoHS Directive 2002/95/EC certain hazardous substances like e.g. lead, cadmium, mercury must not be used any longer in electronic equipment as of July 1st, 2006. For the sake of the environment WIMA has refraind from using such substances since years already. We merely use pure, recyclable materials for packing our components, such as: " " " " carton cardboard adhesive tape made of paper polystyrene We almost completely refrain from using packing materials such as: " foamed polystyrene (Styropor(R)) " adhesive tapes made of plastic " metal clips Tape for lead-free WIMA capacitors DIN EN ISO 14001:2005 WIMA's environmental management has been established in accordance with the guidelines of DIN EN ISO 14001:2005. The certification has been granted in June 2006. 01.10 " " " " " " " WIMA Environmental Policy 16 D Typical Dimensions for Taping Configuration Vh P P2 Diagram 1: PCM 2.5/5/7.5mm W W1 W0 H H1 W2 P1 D0 d P t F P0 H1 P P1 H P1 d d P0 P2 F Diagram 2: PCM 10/15 mm Diagram 3: PCM 22.5 and 27.5*mm *PCM 27.5 taping possible with two feed holes between components Designation Carrier tape width Dimensions for Radial Taping Symbol PCM 2.5 taping W P0 P2 F 18.0 p0.5 PCM 5 taping PCM 7.5 taping PCM 10 taping* PCM 15 taping* PCM 22.5 taping PCM 27.5 taping 18.0 p0.5 18.0 p0.5 18.0 p0.5 18.0 p0.5 18.0 p0.5 18.0 p0.5 for hot-sealing for hot-sealing for hot-sealing for hot-sealing for hot-sealing for hot-sealing for hot-sealing Hold-down tape width W0 6.0 6.0 12.0 12.0 12.0 12.0 12.0 adhesive tapeadhesive tapeadhesive tapeadhesive tapeadhesive tapeadhesive tapeadhesive tape Hole position W1 9.0 p0.5 9.0 p0.5 9.0 p0.5 9.0 p0.5 9.0 p0.5 9.0 p0.5 9.0 p0.5 Hold-down tape position W2 0.5 to 3.0 max. 0.5 to 3.0 max. 0.5 to 3.0 max. 0.5 to 3.0 max. 0.5 to 3.0 max. 0.5 to 3.0 max. 0.5 to 3.0 max. Feed hole diameter D0 4.0 p0.2 4.0 p0.2 4.0 p0.2 4.0 p0.2 4.0 p0.2 4.0 p0.2 12.7 p1.0 12.7 p1.0 12.7 p1.0 25.4 p1.0 25.4 p1.0 38.1 p1.5 4.0 p0.2 3*8.1 p1.5 or 50.8 p1.5 Pitch of component P Feed hole pitch P0 12.7 p0.3 cumulative pitch error max. 1.0 mm/20 pitch 12.7 p0.3 cumulative pitch error max. 1.0 mm/20 pitch 12.7 p0.3 cumulative pitch error max. 1.0 mm/20 pitch 12.7 p0.3 cumulative pitch error max. 1.0 mm/20 pitch 12.7 p0.3 cumulative pitch error max. 1.0 mm/20 pitch 12.7 p0.3 cumulative pitch error max. 1.0 mm/20 pitch 12.7 p0.3 cumulative pitch error max. 1.0 mm/20 pitch Feed hole centre to lead P1 5.1 p0.5 3.85 p0.7 2.6 p0.7 7.7 p0.7 5.2 p0.7 7.8 p0.7 5.3 p0.7 Hole centre to component centre P2 6.35 p1.3 6.35 p1.3 6.35 p1.3 12.7 p1.3 12.7 p1.3 19.05 p1.3 19.05 p1.3 Feed hole centre to bottom H edge of the component 16.5 p0.3 18.5 p0.5 16.5 p0.3 18.5 p0.5 16.5 p0.5 18.5 p0.5 16.5 p0.5 18.5 p0.5 16.5 p0.5 18.5 p0.5 16.5 p0.5 18.5 p0.5 16.5 p0.5 18.5 p0.5 Feed hole centre to top H edge of the component1 H+Hcomponent < H1 32.25 max. H+Hcomponent < H1 32.25 max. H+Hcomponent < H1 24.5 to 31.5 H+Hcomponent < H1 25.0 to 31.5 H+Hcomponent < H1 26.0 to 37.0 H+Hcomponent < H1 30.0 to 43.0 H+Hcomponent < H1 35.0 to 45.0 Lead spacing at +0.8 F 2.5 p0.5 5.0 upper edge of carrier tape -0.2 7.5 p0.8 10.0 p0.8 15 p0.8 22.5 p0.8 27.5 p0.8 Lead diameter d 0.4 p0.05 Component alignment Dh p 2.0 max. p 2.0 max. p 3.0 max. p 3.0 max. p 3.0 max. p 3.0 max. p 3.0 max. 0.7 p0.2 0.7 p0.2 0.7 p0.2 0.7 p0.2 0.7 p0.2 0.7 p0.2 0.7 p0.2 Total tape thickness t Package (see also page 141) REEL 0.5 p0.05 0.5 +0.06 p0.05 or 0.6 -0.05 0.5 +0,06 p0.05 or 0.6 -0.05 ROLL/AMMO P 360 max. 52 p2 P 30 p1B 58 p2 depending on comp. dimensions Unit 0.8 +0,08 -0.05 0.8 +0,08 -0.05 +0.08 0.8 -0.05 AMMO 52 p2 54 p2 max. P 500 max. B 58 p2 or REEL B 60 p2 REEL PP 360 30 p1 P 25 p1 66 p2 68 p2 depending on PCM and component dimensions see details page 143. Dims in mm. Diameter of leads see General Data. * PCM 10 and PCM 15 can be crimped to PCM 7.5. Position of components according to PCM 7.5 (sketch 1). P 0 = 12.7 or 15.0 is possible 140 Please clarify customer-specific deviations with the manufacturer. 01.10 D Packing Quantities for Bulk Capacitors and TPS* Part number codes 2.5 mm 5 mm 7.5 mm 10 mm 15 mm 22.5 mm 27.5 mm 37.5 mm 142 Size W H L 2.5 3 3.8 4.6 5.5 2.5 3 3.5 4.5 4.5 5 5.5 5.5 6.5 7.2 7.2 8.5 8.5 11 2.5 3 4 4.5 5 5.7 7.2 3 4 4 4 5 5 6 6 8 5 5 6 6 7 7 8 8 9 9 10 11 5 6 7 8 8.5 10 10.5 10.5 11 12 9 11 13 13 15 15 17 17 20 20 9 11 13 15 17 19 20 24 7 7.5 8.5 9 10 6.5 7.5 8.5 6 9.5 10 7 11.5 8 8.5 13 10 14 16 7 8.5 9 9.5 10.5 12.5 12.5 9 8.5 9 9.5 10 11 12 12.5 12 11 13 12.5 14 14 15 15 17 14 16 18 14 14 15 16.5 20 18.5 22 19 20.5 21 24 19 21 24 25 26 26 29 34.5 32 39.5 19 22 24 26 29 32 39.5 45.5 4.6 4.6 4.6 4.6 4.6 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 10 10 10 10.3 10.3 10.3 10.3 13 13.5 13 13 13.5 13 13 13 13 18 19 18 19 18 19 18 19 18 18 19 18 26.5 26.5 26.5 28 26.5 28 26.5 26.5 26.5 28 31.5 31.5 31.5 33 31.5 33 31.5 31.5 33 31.5 41.5 41.5 41.5 41.5 41.5 41.5 41.5 41.5 pcs. per packaging unit bulk Mini Standard Maxi M S G 1000 1000 1000 1000 1000 2000 1000 1000 1000 1000 1000 1000 500 1000 500 500 500 500 250 1000 1000 1000 1000 1000 500 500 1000 500 1000 1000 500 1000 800 800 500 800 200 500 250 400 250 400 100 400 300 100 300 300 250 190 - - - - - - - - - - - - - - - - - - - - - - - - - 5000 5000 5000 5000 5000 5000 5000 5000 6000 4000 3500 4000 2500 2500 2500 2000 2000 1500 1000 5000 5000 4000 3500 3000 2000 1500 3000 3000 3000 3000 2000 3000 2400 2400 2000 2400 1000 2000 1000 1600 1000 1200 500 1200 900 500 1000 1200 1000 760 - - - - - - - - - - - - - - - - - - - - - - - - - Rights reserved to amend design data without prior notification. Samples and pre-production needs on request. 10 000 10 000 10 000 10 000 10 000 10 000 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - pcs. per packaging unit/TPS* Mini Standard X Y - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 115 220 90 170 170 170 75 160 136 112 56 96 48 88 88 36 36 60 51 84 72 66 54 27 21 Moulded versions. - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 690 880 540 680 680 680 450 640 544 448 336 384 288 176 176 216 144 480 408 252 144 132 108 108 84 * Tray-Packing-System 01.10 PCM D Packing Units for Taped Capacitors with Radial Leads ROLL PCM Part number codes Size H L 2.5 3 3.8 4.6 5.5 7 7.5 8.5 9 10 4.6 4.6 4.6 4.6 4.6 2200 2000 1500 1200 900 2500 2300 1800 1500 1200 - - - - - 2800 2300 1800 1500 1200 - - - - - 2.5 3 3.5 4.5 4.5 5 5.5 5.5 6.5 7.2 7.2 8.5 8.5 11 6.5 7.5 8.5 6 9.5 10 7 11.5 8 8.5 13 10 14 16 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 2200 2000 1600 1300 1300 1100 1000 1000 800 700 700 600 600 500 2500 2300 2000 1500 1500 1400 1200 1200 1000 1000 950 800 800 700 - - - - - - - - - - - - - - 2800 2300 2000 1500 1500 1400 1200 1200 1000 1000 1000 800 800 700 - - - - - - - - - - - - - - 7.5 mm 2.5 3 4 4.5 5 5.7 7.2 7 8.5 9 9.5 10.5 12.5 12.5 10 10 10 10.3 10.3 10.3 10.3 - - - - - - - 2500 2200 1700 1500 1300 1000 900 4400 4300 3200 2900 2500 2200 1800 2800 2300 1700 1400 1300 1100 1000 - 4150 3100 2800 - - - 10 mm 3 4 4 4 5 5 6 6 8 9 8.5 9 9.5 10 11 12 12.5 12 13 13.5 13 13 13.5 13 13 13 13 - - - - - - - - - 1100 900 900 900 700 700 550 550 400 2200 1600 1600 1600 1300 1300 1100 1100 800 - - - - - - - - - 1900 1450 1450 1400 1200 1200 1000 1000 740 15 mm 5 5 6 6 7 7 8 8 9 9 10 11 11 13 12.5 14 14 15 15 17 14 16 18 14 18 19 18 19 18 19 18 19 18 18 19 18 - - - - - - - - - - - - 600 600 500 500 450 450 400 400 350 350 300 300 1200 1200 1000 1000 900 900 800 800 700 700 650 600 - - - - - - - - - - - - 1150 1200 1000 1000 850 850 740 740 650 650 590 540 22.5 mm 5 6 7 8 8.5 10 10.5 10.5 11 12 14 15 16.5 20 18.5 22 19 20.5 21 24 26.5 26.5 26.5 28 26.5 28 26.5 26.5 26.5 28 - - - - - - - - - - - - - - - - - - - - 800 700 600 500 480 420 400 400 380 350 - - - - - - - - - - 770 640 550 480 450 380 360 360 350 310 27.5 mm 9 11 13 15 19 21 24 26 31.5 31.5 31.5 31.5 - - - - - - - - 460/340* 380/280* 300 270 - - - - 420 350 290 250 2.5 mm 5 mm W REEL AMMO P 360 P 500 340 x 340 490 x 370 H16.5 H18.5 H16.5 H18.5 H16.5 H18.5 H16.5 H18.5 H16.5 H18.5 N O F I H J A C B D Moulded versions. Rights reserved to amend design data without prior notification. 01.10 * for 2-inch transport pitches. Samples and pre-production needs 1 packing unit minimum. 143 D WIMA Part Number System A WIMA part number consists of 18 digits and is composed as follows: 1 - 4: Type description 5 - 6: Rated voltage 7 - 10: Capacitance 11 - 12: Size and PCM 13 - 14: Special features (e.g. Snubber versions) 15: Capacitance tolerance 16: Packing 17 - 18: Lead length (untaped) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 M K S 2 C 0 3 1 0 0 1 A 0 0 M S S D 20 % bulk MKS 2 Type description: SMD-PET = SMD-PEN = SMD-PPS = FKP 02 = MKS 02 = FKS 2 = FKM 2 = FKP 2 = MKS 2 = MKP 2 = MKI 2 = FKS 3 = FKM 3 = FKP 3 = MKS 4 = MKM 4 = MKP 4 = MKP 10 = FKP 4 = FKP 1 = MKP-X2 = MKP-X2 R = MKP-Y2 = MP 3-X2 = MP 3-X1 = MP 3-Y2 = MP 3R-Y2 = Snubber FKP = Snubber MKP = GTO MKP = DC-LINK MKP 4 = DC-LINK MKP C = DC-LINK HC = SuperCap C = SuperCap MC = SuperCap R = SuperCap MR = 63 VDC SMDT SMDN SMDI FKS0 MKS0 FKS2 FKM2 FKP2 MKS2 MKP2 MKI2 FKS3 FKM3 FKP3 MKS4 MKM4 MKP4 MKP1 FKP4 FKP1 MKX2 MKXR MKY2 MPX2 MPX1 MPY2 MPYR SNFP SNMP GTOM DCP4 DCPC DCH_ SCSC SCMC SCSR SCMR Rated voltage: 16 VDC = A0 2.5 VDC = A1 4 VDC = A2 14 VDC = A3 28 VDC = A4 40 VDC = A5 50 VDC = B0 63 VDC = C0 100 VDC = D0 160 VDC = E0 250 VDC = F0 400 VDC = G0 630 VDC = J0 800 VDC = L0 850 VDC = M0 1000 VDC = O1 1200 VDC = Q0 1600 VDC = T0 2000 VDC = U0 2500 VDC = V0 4000 VDC = X0 6000 VDC = Y0 250 VAC = 0W 275 VAC = 1W 300 VAC = 2W 400 VAC = 3W 440 VAC = 4W 500 VAC = 5W ... 0.01 mF Capacitance: 22 pF = 0022 47 pF = 0047 100 pF = 0100 220 pF = 0220 470 pF = 0470 1000 pF = 1100 2200 pF = 1220 4700 pF = 1470 0.01 mF = 2100 0.022 mF = 2220 0.047 mF = 2470 0.1 mF = 3100 0.22 mF = 3220 0.47 mF = 3470 = 4100 1 mF 2.2 mF = 4220 4.7 mF = 4470 = 5100 10 mF = 5220 22 mF = 5470 47 mF 100 mF = 6100 220 mF = 6220 1F = A010 2.5 F = A025 50 F = A500 100 F = B100 600 F = B600 1200 F = C120 ... - 2.5 x 6.5 x 7.2 Size: 4.8 x 3.3 x 3 Size 1812 5.7 x 5.1 x 3.5 Size 2220 7.2 x 6.1 x 3 Size 2824 2.5 x 7 x 4.6 PCM 2.5 3 x 7.5 x 4.6 PCM 2.5 2.5 x 6.5 x 7.2 PCM 5 3 x 7.5 x 7.2 PCM 5 2.5 x 7 x 10 PCM 7.5 3 x 8.5 x 10 PCM 7.5 3 x 9 x 13 PCM 10 4 x 9 x 13 PCM 10 5 x 11 x 18 PCM 15 6 x 12.5 x 18 PCM 15 5 x 14 x 26.5 PCM 22.5 6 x 15 x 26.5 PCM 22.5 9 x 19 x 31.5 PCM 27.5 11 x21 x 31.5 PCM 27.5 9 x 19 x 41.5 PCM 37.5 11 x 22 x 41.5 PCM 37.5 94 x 49 x 182 DCH_ 94 x 77 x 182 DCH_ ... Special features: Standard = 00 Version A1 = 1A Version A1.1 = 1B ... = = = = = = = = = = = = = = = = = = = = = X1 Y1 T1 0B 0C 1A 1B 2A 2B 3A 3B 4A 4B 5A 5B 6A 6B 7A 7B H0 H1 Tolerance: 20 % = 10 % = 5% = 2.5 % = 1% = ... 6 -2 M K J H E Packing: AMMO H16.5 340 x 340 AMMO H16.5 490 x 370 AMMO H18.5 340 x 340 AMMO H18.5 490 x 370 REEL H16.5 360 REEL H16.5 500 REEL H18.5 360 REEL H18.5 500 ROLL H16.5 ROLL H18.5 BLISTER W12 180 BLISTER W12 330 BLISTER W16 330 BLISTER W24 330 Bulk Mini Bulk Standard Bulk Maxi TPS Mini TPS Standard ... A B C D F H I J N O P Q R T M S G X Y Lead length (untaped) 3.5 0.5 = C9 6 -2 = SD 16 -1 = P4 ... The data on this page is not complete and serves only to explain the part number system. Part number information is listed on the pages of the respective WIMA range. 138 = = = = = = = = = = = = = = = = = = = 01.10 Field Field Field Field Field Field Field Field