For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
LINEAR & POWER AMPLIFIER - CHIP
1
HMC-ABH209
v03.0714
Gaas HEMT MMIC MEDIUM POWER
AMPLIFIER, 55 - 65 GHz
General Description
Features
Functional Diagram
Output IP3: +25 dBm
P1dB: +16 dBm
Gain: 13 dB
Supply Voltage: +5V
50 Ohm Matched Input/Output
Die Size: 2.2 x 1.22 x 0.1 mm
Electrical Specications, TA = +25 °C, Vdd = 5V, Idd = 80mA [2]
Typical Applications
This HMC-ABH209 is ideal for:
• Short Haul / High Capacity Links
• Wireless LAN Bridges
• Military & Space
The HMC-ABH209 is a high dynamic range, two
stage GaAs HEMT MMIC Medium Power Amplier
which operates between 55 and 65 GHz. The HMC-
ABH209 provides 13 dB of gain, and an output power
of +16 dBm at 1 dB compression from a +5V supply
voltage. All bond pads and the die backside are
Ti/Au metallized and the amplier device is fully
passivated for reliable operation. The HMC-ABH209
GaAs HEMT MMIC Medium Power Amplier is
compatible with conventional die attach methods,
as well as thermocompression and thermosonic
wirebonding, making it ideal for MCM and hybrid
microcircuit applications. All data shown herein is
measured with the chip in a 50 Ohm environment and
contacted with RF probes.
Parameter Min. Ty p. Max. Units
Frequency Range 55 - 65 GHz
Gain 12 13 dB
Input Return Loss 13 dB
Output Return Loss 17 dB
Output Power for 1 dB Compression (P1dB) 16 dBm
Output Third Order Intercept (IP3) 25 dBm
Saturated Output Power (Psat) 18 dBm
Supply Current (Idd) 80 mA
[1] Unless otherwise indicated, all measurements are from probed die
[2] Adjust Vgg between -1V to +0.3V (typ -0.3V) to achieve Iddtotal = 80mA
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
For price, delivery, and to place orders: Analog Devices, Inc.,
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
Phone: 781-329-4700 • Order online at www.analog.com
Application Support: Phone: 1-800-ANALOG-D
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
LINEAR & POWER AMPLIFIER - CHIP
2
HMC-ABH209
v03.0714
Gaas HEMT MMIC MEDIUM POWER
AMPLIFIER, 55 - 65 GHz
Fixtured Output Power vs. Frequency
Output Return Loss vs. Frequency
Linear Gain vs. Frequency
Input Return Loss vs. Frequency
0
2
4
6
8
10
12
14
16
18
50 52 54 56 58 60 62 64 66 68
GAIN (dB)
FREQUENCY (GHz)
-30
-25
-20
-15
-10
-5
0
50 52 54 56 58 60 62 64 66 68
RETURN LOSS (dB)
FREQUENCY (GHz)
-30
-25
-20
-15
-10
-5
0
50 52 54 56 58 60 62 64 66 68
RETURN LOSS (dB)
FREQUENCY (GHz)
10
12
14
16
18
20
55 56 57 58 59 60 61 62 63 64 65
P1dB P5dB
POUT (dBm)
FREQUENCY (GHz)
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
For price, delivery, and to place orders: Analog Devices, Inc.,
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
Phone: 781-329-4700 • Order online at www.analog.com
Application Support: Phone: 1-800-ANALOG-D
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
LINEAR & POWER AMPLIFIER - CHIP
3
HMC-ABH209
v03.0714
Gaas HEMT MMIC MEDIUM POWER
AMPLIFIER, 55 - 65 GHz
Outline Drawing
Absolute Maximum Ratings
ELECTROSTATIC SENSITIVE DEVICE
OBSERVE HANDLING PRECAUTIONS
NOTES:
1. ALL DIMENSIONS ARE IN INCHES [MM].
2. TYPICAL BOND PAD IS .004” SQUARE.
3. BACKSIDE METALLIZATION: GOLD.
4. BACKSIDE METAL IS GROUND.
5. BOND PAD METALLIZATION: GOLD.
6. CONNECTION NOT REQUIRED FOR UNLABELED BOND PADS.
7. OVERALL DIE SIZE ±.002”
Drain Bias Voltage +5.5 Vdc
Gain Bias Voltage -1 to +0.3 Vdc
RF Input Power 10 dBm
Storage Temperature -65 °C to + 150 °C
Chennel Temperature +180 °C
Die Packaging Information [1]
Standard Alternate
GP-2 (Gel Pack) [2]
[1] Refer to the “Packaging Information” section for die
packaging dimensions.
[2] For alternate packaging information contact Hittite
Microwave Corporation.
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
For price, delivery, and to place orders: Analog Devices, Inc.,
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
Phone: 781-329-4700 • Order online at www.analog.com
Application Support: Phone: 1-800-ANALOG-D
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
LINEAR & POWER AMPLIFIER - CHIP
4
HMC-ABH209
v03.0714
Gaas HEMT MMIC MEDIUM POWER
AMPLIFIER, 55 - 65 GHz
Pad Number Function Description Interface Schematic
1RFIN This pad is AC coupled and matched to
50 Ohms.
2RFOUT This pad is AC coupled and matched to
50 Ohms.
3Vdd Power Supply Voltage for the amplier. See assembly for
required external components.
4Vgg
Gate control for amplier. Please follow “MMIC Amplier
Biasing Procedure” application note. See assembly for
required external components.
Die Bottom GND Die bottom must be connected to RF/DC ground.
Pad Descriptions
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
For price, delivery, and to place orders: Analog Devices, Inc.,
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
Phone: 781-329-4700 • Order online at www.analog.com
Application Support: Phone: 1-800-ANALOG-D
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
LINEAR & POWER AMPLIFIER - CHIP
5
HMC-ABH209
v03.0714
Gaas HEMT MMIC MEDIUM POWER
AMPLIFIER, 55 - 65 GHz
Assembly Diagram
Note 1: Bypass caps should be 100 pF (approximately) ceramic (single-layer) placed no farther than 30 mils from the amplier.
Note 2: Best performance obtained from use of <10 mil (long) by 3 by 0.5 mil ribbons on input and output.
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
For price, delivery, and to place orders: Analog Devices, Inc.,
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
Phone: 781-329-4700 • Order online at www.analog.com
Application Support: Phone: 1-800-ANALOG-D
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
LINEAR & POWER AMPLIFIER - CHIP
6
HMC-ABH209
v03.0714
Gaas HEMT MMIC MEDIUM POWER
AMPLIFIER, 55 - 65 GHz
Mounting & Bonding Techniques for Millimeterwave GaAs MMICs
The die should be attached directly to the ground plane eutectically or with
conductive epoxy (see HMC general Handling, Mounting, Bonding Note).
50 Ohm Microstrip transmission lines on 0.127mm (5 mil) thick alumina
thin lm substrates are recommended for bringing RF to and from the chip
(Figure 1). If 0.254mm (10 mil) thick alumina thin lm substrates must be
used, the die should be raised 0.150mm (6 mils) so that the surface of
the die is coplanar with the surface of the substrate. One way to accom-
plish this is to attach the 0.102mm (4 mil) thick die to a 0.150mm (6 mil)
thick molybdenum heat spreader (moly-tab) which is then attached to the
ground plane (Figure 2).
Microstrip substrates should be placed as close to the die as possible in
order to minimize bond wire length. Typical die-to-substrate spacing is
0.076mm to 0.152 mm (3 to 6 mils).
Handling Precautions
Follow these precautions to avoid permanent damage.
Storage: All bare die are placed in either Waffle or Gel based ESD pro-
tective containers, and then sealed in an ESD protective bag for shipment.
Once the sealed ESD protective bag has been opened, all die should be
stored in a dry nitrogen environment.
Cleanliness: Handle the chips in a clean environment. DO NOT attempt
to clean the chip using liquid cleaning systems.
Static Sensitivity: Follow ESD precautions to protect against ESD
strikes.
Transients: Suppress instrument and bias supply transients while bias is
applied. Use shielded signal and bias cables to minimize inductive pick-up.
General Handling: Handle the chip along the edges with a vacuum collet
or with a sharp pair of bent tweezers. The surface of the chip may have fragile air bridges and should not be touched
with vacuum collet, tweezers, or ngers.
Mounting
The chip is back-metallized and can be die mounted with AuSn eutectic preforms or with electrically conductive epoxy.
The mounting surface should be clean and at.
Eutectic Die Attach: A 80/20 gold tin preform is recommended with a work surface temperature of 255 °C and a tool
temperature of 265 °C. When hot 90/10 nitrogen/hydrogen gas is applied, tool tip temperature should be 290 °C. DO
NOT expose the chip to a temperature greater than 320 °C for more than 20 seconds. No more than 3 seconds of
scrubbing should be required for attachment.
Epoxy Die Attach: Apply a minimum amount of epoxy to the mounting surface so that a thin epoxy llet is observed
around the perimeter of the chip once it is placed into position. Cure epoxy per the manufacturer’s schedule.
Wire Bonding
RF bonds made with 0.003” x 0.0005” ribbon are recommended. These bonds should be thermosonically bonded
with a force of 40-60 grams. DC bonds of 0.001” (0.025 mm) diameter, thermosonically bonded, are recommended.
Ball bonds should be made with a force of 40-50 grams and wedge bonds at 18-22 grams. All bonds should be made
with a nominal stage temperature of 150 °C. A minimum amount of ultrasonic energy should be applied to achieve
reliable bonds. All bonds should be as short as possible, less than 12 mils (0.31 mm).
0.102mm (0.004”) Thick GaAs MMIC
Wire Bond
RF Ground Plane
0.127mm (0.005”) Thick Alumina
Thin Film Substrate
0.076mm
(0.003”)
Figure 1.
0.102mm (0.004”) Thick GaAs MMIC
Wire Bond
RF Ground Plane
0.254mm (0.010”) Thick Alumina
Thin Film Substrate
0.076mm
(0.003”)
Figure 2.
0.150mm (0.005”) Thick
Moly Tab
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
For price, delivery, and to place orders: Analog Devices, Inc.,
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
Phone: 781-329-4700 • Order online at www.analog.com
Application Support: Phone: 1-800-ANALOG-D