LTC2930 Configurable Six Supply Monitor with Adjustable Reset Timer, Manual Reset DESCRIPTION FEATURES Simultaneously Monitors Six Supplies 16 User Selectable Combinations of 5V, 3.3V, 3V, 2.5V, 1.8V, 1.5V and Adjustable Voltage Thresholds Guaranteed 1.5% Threshold Accuracy Adjustable Reset Timeout Low Supply Current: 52A Manual Reset Pin Power Supply Glitch Immunity Guaranteed RST for VCC 1V High Temperature Operation to 125C 12-Lead 3mm x 3mm DFN Package The LTC(R)2930 is a configurable supply monitor for systems with up to six supply voltages. One of 16 preset or adjustable voltage monitor combinations can be selected using an external resistive divider connected to the mode select pin. The preset voltage thresholds are accurate to 1.5% over temperature. The LTC2930 also features adjustable inputs with a 0.5V nominal threshold. The reset timeout period is adjustable using an external capacitor. A reset event may be generated with a manual reset button on the manual reset input. Tight voltage threshold accuracy and glitch immunity ensure reliable reset operation without false triggering. The RST output is guaranteed to be in the correct state for VCC down to 1V and may be externally pulled up to an external voltage. APPLICATIONS Desktop and Notebook Computers Multivoltage Systems Telecom Equipment Portable Battery-Powered Equipment Network Servers Automotive The 52A supply current makes the LTC2930 ideal for power conscious systems and it may be configured to monitor fewer than six inputs. L, LT, LTC and LTM are registered trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. Protected by U.S. Patents including 6967591, 7119714, 7239251. TYPICAL APPLICATION Six Supply Monitor, 5% Threshold 12V, 5V, 3.3V, 1.8V, 1.2V, -5.2V Voltage Threshold Configuration Table 12V V1 (V) V2 (V) V3 (V) V4 (V) V5 (V) 5.0 3.3 2.5 1.8 ADJ ADJ 5.0 3.3 2.5 1.5 ADJ ADJ 5.0 3.3 2.5 ADJ ADJ ADJ 5.0 3.3 1.8 ADJ ADJ ADJ 5.0 3.3 1.8 -ADJ ADJ ADJ 5.0 3.3 ADJ ADJ ADJ ADJ 5.0 3.3 ADJ -ADJ ADJ ADJ 5.0 3.0 2.5 ADJ ADJ ADJ V5 5.0 3.0 1.8 ADJ ADJ ADJ V6 5.0 3.0 ADJ ADJ ADJ ADJ 3.3 2.5 1.8 1.5 ADJ ADJ 3.3 2.5 1.8 ADJ ADJ ADJ 3.3 2.5 1.8 -ADJ ADJ ADJ 3.3 2.5 1.5 ADJ ADJ ADJ 3.3 2.5 ADJ ADJ ADJ ADJ 3.3 2.5 ADJ -ADJ ADJ ADJ 5V 3.3V 1.8V SYSTEM LOGIC 1.2V -5.2V 2150k 1% 487k 1% V1 V2 0.1F V3 124k 1% V4 121k 1% 100k 1% 100k 1% 16.2k 1% 86.6k 1% RST LTC2930 MR VREF VPG GND CRT MANUAL RESET CRT 47nF 2930 TA01 tRST = 94ms V6 (V) 2930fa 1 LTC2930 ABSOLUTE MAXIMUM RATINGS PIN CONFIGURATION (Notes 1, 2, 3) V1, V2, V3, V4, V5, V6, VPG, RST................ -0.3V to 7V CRT, VREF, MR...............................-0.3V to (VCC + 0.3V) Reference Load Current (IVREF) ..............................1mA V4 Input Current (-ADJ Mode) ..............................-1mA RST Current .........................................................10mA Operating Temperature Range LTC2930C ................................................ 0C to 70C LTC2930I.............................................. -40C to 85C LTC2930H .......................................... -40C to 125C Storage Temperature Range................... -65C to 150C TOP VIEW 12 V6 V5 1 V3 2 V1 3 CRT 4 9 VREF RST 5 8 VPG MR 6 7 GND 11 V2 10 V4 13 DD PACKAGE 12-LEAD (3mm x 3mm) PLASTIC DFN TJMAX = 130C, JA = 43C/W EXPOSED PAD (PIN 13) IS GND (PCB CONNECTION OPTIONAL) ORDER INFORMATION LEAD FREE FINISH TAPE AND REEL PART MARKING* PACKAGE DESCRIPTION TEMPERATURE RANGE LTC2930CDD#PBF LTC2930CDD#TRPBF LDMJ 12-Lead 3mm x 3mm DFN 0C to 70C LTC2930IDD#PBF LTC2930IDD#TRPBF LDMJ 12-Lead 3mm x 3mm DFN -40C to 85C LTC2930HDD#PBF LTC2930HDD#TRPBF LDMJ 12-Lead 3mm x 3mm DFN -40C to 125C *The temperature grade is identified by a label on the shipping container. For more information on lead free part marking, go to: http://www.linear.com/leadfree/ This product is only offered in trays. For more information go to: http://www.linear.com/packaging/ ELECTRICAL CHARACTERISTICS The denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. VCC = 5V, unless otherwise specified. (Note 3) SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS VCC Minimum Internal Operating Voltage RST in Correct Logic State VCCMINP Minimum Required for Mode Selection VCC Rising VRT50 5V, 5% Reset Threshold V1 Input Threshold 4.600 4.675 VRT33 3.3V, 5% Reset Threshold V1, V2 Input Threshold 3.036 3.086 3.135 V VRT30 3V, 5% Reset Threshold V2 Input Threshold 2.760 2.805 2.850 V VRT25 2.5V, 5% Reset Threshold V2, V3 Input Threshold 2.300 2.338 2.375 V VRT18 1.8V, 5% Reset Threshold V3, V4 Input Threshold 1.656 1.683 1.710 V 1 V 2.4 V 4.750 V VRT15 1.5V, 5% Reset Threshold V3, V4 Input Threshold 1.380 1.403 1.425 V VRTA ADJ Reset Threshold V3, V4, V5, V6 Input Threshold 492.5 500 507.5 mV VRTAN -ADJ Reset Threshold V4 Input Threshold -18 0 18 mV VREF Reference Voltage VCC 2.3V, IVREF = 1mA, CREF 1000pF 1.192 1.210 1.228 V VPG Mode Selection Voltage Range VCC VCCMINP 0 VREF V VPG = VREF 20 nA IVPG VPG Input Current 2930fa 2 LTC2930 ELECTRICAL CHARACTERISTICS The denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. VCC = 5V, unless otherwise specified. (Note 3) SYMBOL PARAMETER CONDITIONS MIN IV1 V1 Input Current V1 = 5V, IVREF = 12A (Note 4) TYP MAX 52 75 UNITS A IV2 V2 Input Current V2 = 3.3V 0.8 2 A IV3 V3 Input Current V3 = 2.5V V3 = 0.55V (ADJ Mode) 0.52 1.2 15 A nA IV4 V4 Input Current V4 = 1.8V V4 = 0.55V (ADJ Mode) V4 = -0.02V (-ADJ Mode) 0.34 0.8 15 15 A nA nA IV5, IV6 V5, V6 Input Current V5, V6 = 0.55V 15 nA ICRT(UP) CRT Pull-Up Current VCRT = GND -1.4 -2 -2.6 A ICRT(DN) CRT Pull-Down Current VCRT = 1.3V 10 20 30 A 2 3 4 ms tRST Reset Timeout Period CRT = 1500pF tUV Vn Undervoltage Detect to RST Vn Less Than Reset Threshold by More than 1% VOL Voltage Output Low RST ISINK = 3mA, VCC = 3V ISINK = 100A, VCC = 1V VOH Voltage Output High RST (Note 5) ISOURCE = -1A VIL MR Input Threshold Low VCC = 3.3V to 5.5V VIH MR Input Threshold High VCC = 3.3V to 5.5V 1.6 V tMRW MR Input Pulse Width VCC = 3.3V 150 ns tMRD Manual Reset Propagation Delay VCC = 3.3V, VMR Falling IMR MR Pull-Up Current VMR = 1V Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: All currents into pins are positive, all voltages are referenced to GND unless otherwise noted. Note 3: The greater of V1, V2 is the internal supply voltage (VCC). 150 0.15 0.05 s 0.4 0.3 V2-1 V 0.4 -4 V V V 0.1 1 s -10 -16 A Note 4: Under static no-fault conditions, V1 will necessarily supply quiescent current. If at any time V2 is larger than V1, V2 must be capable of supplying the quiescent current, programming (transient) current and reference load current. Note 5: The output pin RST has a diode protected internal pull-up to V2 of typically 6A. However, an external pull-up resistor may be used when faster rise times are required or for VOH voltages greater than V2. TIMING DIAGRAM Vn Monitor Timing Vn VRT tUV tRST tMRD tRST RST 2930 TD MR tMRW 2930fa 3 LTC2930 TYPICAL PERFORMANCE CHARACTERISTICS -ADJ Threshold Voltage vs Temperature 1.010 1.005 1.000 0.995 0.990 0.985 -50 -25 50 25 75 0 TEMPERATURE (C) 100 VREF vs Temperature 18 1.228 12 1.222 6 1.216 VREF (V) 1.015 THRESHOLD VOLTAGE, VRTAN (mV) NORMALIZED THRESHOLD VOLTAGES (V/V) Normalized Threshold Voltages vs Temperature 0 -6 1.204 -12 1.198 -18 -50 -25 125 50 25 75 0 TEMPERATURE (C) 100 2930 G01 TYPICAL TRANSIENT DURATION (s) 300 125C IV4 (A) -1 -100n 50 -10n 45 -1n 90C 25C 100 125 -100p -300 -250 -200 -150 -100 V4 (mV) -50 250 200 RESET OCCURS ABOVE CURVE 150 100 50 0 0 0.1 1 10 100 RESET COMPARATOR OVERDRIVE (% OF VRTX) 2930 G05 2930 G06 RST Output Voltage vs V1, VPG = GND 5 TA = 25C 10k PULL-UP FROM RST TO V1 5 375 RESET OCCURS ABOVE CURVE 225 150 75 RST OUTPUT VOLTAGE (V) TYPICAL TRANSIENT DURATION (s) 6 TA = 25C Reset Timeout Period vs Temperature RESET TIMEOUT PERIOD, tRST (ms) Transient Duration vs Comparator Overdrive (V3, V4, V5, V6) 300 4 3 2 1 0 0 0.1 1 10 100 RESET COMPARATOR OVERDRIVE (% OF VRTX) 2930 G07 125 TA = 25C 2930 G04 450 100 Transient Duration vs Comparator Overdrive (V1,V2) -10 55 50 25 75 0 TEMPERATURE (C) 2930 G03 -100 V1 = 5V V2 = 3.3V 65 V3 = 2.5V V4 = 1.8V V5 = V6 = 1V 60 50 25 75 0 TEMPERATURE (C) 1.192 -50 -25 I(V4) vs V4 in Negative Adjust Mode 70 SUPPLY CURRENT, IV1 (A) 125 2930 G02 Supply Current vs Temperature 40 -50 -25 1.210 0 1 2 3 4 5 V1 (V) 2930 G08 CRT = 1500pF (SILVER MICA) 4 3 2 1 -50 -25 75 0 25 50 TEMPERATURE (C) 100 125 2930 G09 2930fa 4 LTC2930 TYPICAL PERFORMANCE CHARACTERISTICS ISINK vs Supply Voltage (RST) Reset Timeout Period vs CRT 15 TA = 25C 1 TA = 25C 12 VOL = 0.4V 100m ISINK (mA) RESET TIMEOUT PERIOD tRST (s) 10 10m 9 VOL = 0.2V 6 1m 3 100 10 10p 100p 1n 10n CRT (F) 100n 0 1 1 0 2930 G10 3 2 V1 OR V2 (V) 4 5 2930 G11 Voltage Output Low vs Output Sink Current (RST) 500 RST Pull-Up Current vs V2 18 V1 = 5V V2 = 3V 125C 15 PULL-UP CURRENT (A) 400 VOL (mV) 85C 300 25C 200 -40C 100 0 TA = 25C 12 9 VRT33 VRT30 6 3 VRT25 0 0 2 6 4 ISINK (mA) 8 10 2930 G12 2.0 2.5 3.0 3.5 V2 (V) 4.0 4.5 5.0 2930 G13 PIN FUNCTIONS V5 (Pin 1): Adjustable Voltage Input 5. High impedance comparator input with 0.5V typical threshold. See Applications Information for details. Tie to V1 if unused. V3 (Pin 2): Voltage Input 3. Select from 2.5V, 1.8V, 1.5V, or ADJ. See Applications Information for details. Tie to V1 if unused. V1 (Pin 3): Voltage Input 1. Select from 5V or 3.3V. See Applications Information for details. The greater of V1 or V2 is also VCC for the device. Bypass this pin to ground with a 0.1F (or greater) capacitor. CRT (Pin 4): Reset Timeout Capacitor. Attach an external capacitor (CRT) to GND to set a reset timeout of 2ms/nF. Leaving the pin open generates a minimum delay of approximately 25s. A 47nF capacitor generates a 94ms reset delay time. RST (Pin 5): Reset Output. Logic output with weak 6A pull-up to V2. Pulls low when any voltage input is below the reset threshold and held low for the configured delay time after all voltage inputs are above threshold. Use an external pull-up to pull greater than V2. Leave open if unused. 2930fa 5 LTC2930 PIN FUNCTIONS MR (Pin 6): Manual Reset Input. A logic low on this pin pulls RST low. When the MR pin returns high, RST returns high after the configured reset timeout if all six voltage inputs are above threshold. A weak internal pull-up allows the pin to be left open for normal monitor operation. When using a switch, the switch is debounced through the reset circuitry using the delay provided by the CRT timing capacitor. GND (Pin 7): Ground. VPG (Pin 8): Threshold Select Input. Connect to an external 1% resistive divider between VREF and GND to select 1 of 16 combinations and/or adjustable voltage thresholds (See Table 1). Do not add capacitance on the VPG pin. VREF (Pin 9): Buffered Reference Voltage Output. A 1.210V nominal reference used for the mode selection voltage (VPG) and for the offset of negative adjustable applications. The buffered reference can source and sink up to 1mA. The reference can drive a bypass capacitor of up to 1000pF without oscillation. V4 (Pin 10): Voltage Input 4. Select from 1.8V, 1.5V, ADJ or -ADJ. See Applications Information for details. Tie to V1 if unused. V2 (Pin 11): Voltage Input 2. Select from 3.3V, 3V or 2.5V. See Applications Information for details. The greater of V1, V2 is also VCC for the device. Bypass this pin to ground with a 0.1F (or greater) capacitor. RST is weakly pulled up to V2. V6 (Pin 12): Adjustable Voltage Input 6. High impedance comparator input with 0.5V typical threshold. See Applications Information for details. Tie to V1 if unused. Exposed Pad (Pin 13): Exposed pad may be left open or connected to device ground. BLOCK DIAGRAM BUFFER VREF 9 1.210V BANDGAP REFERENCE VPG 8 V1 A/D POWER DETECT V1 VCC 3 V2 11 V3 2 RESISTIVE DIVIDER MATRIX 4 - 4 + V2 CMP1-4 V4 10 V5 - 1 + V2 CMP5 6A 0.5V RST + ADJUSTABLE RESET PULSE GENERATOR CMP6 V6 12 4 - 5 VCC 2A 10A GND 7 22A VCC 6 MR 4 CRT CRT 2931 BD 2930fa 6 LTC2930 APPLICATIONS INFORMATION Supply Monitoring Table 1. Voltage Threshold Modes* The LTC2930 is a low power, high accuracy configurable six supply monitoring circuit with a common reset output. An external capacitor sets the reset timeout period. An external resistive divider between VREF, VPG and GND selects 1 of 16 possible input voltage monitor combinations. All six voltage inputs must be above their predetermined thresholds for the reset not to be activated. The LTC2930 asserts the reset output during power-up, power-down and brownout conditions on any one of the voltage inputs. Power-Up The greater of V1 and V2 serves as the internal supply voltage (VCC). On power-up, VCC powers the drive circuits for the RST pin. This ensures that the RST output will be low as soon as either V1 or V2 reaches 1V. The RST output remains low until the part is configured. Once voltage thresholds are set, if any of the supply monitor inputs is below its configured threshold, RST will be a logic low. Once all the monitor inputs rise above their thresholds, an internal timer is started and RST is released after the delay time. If VCC < (V3 - 1.0V) and VCC < 2.4V, the V3 input impedance will be low (10k typical). Threshold Accuracy Consider a 5V system with 5% tolerance. The 5V supply may vary between 4.75V to 5.25V. System ICs powered by this supply must operate reliably within this band (and a little more as explained below). A perfectly accurate su5V SUPPLY TOLERANCE MINIMUM RELIABLE SYSTEM VOLTAGE IDEAL SUPERVISOR THRESHOLD 4.75V 1.5% THRESHOLD BAND NOMINAL SUPPLY VOLTAGE -5% 4.675V -6.5% 4.6V -8% REGION OF POTENTIAL MALFUNCTION Figure 1. 1.5% Threshold Accuracy Improves System Reliability MODE V1 (V) V2 (V) V3 (V) V4 (V) R1 (k) R2 (k) VPG VREF 0 5.0 3.3 ADJ ADJ Open Short 0.000 1 5.0 3.3 ADJ -ADJ 93.1 9.53 0.094 2 3.3 2.5 ADJ ADJ 86.6 16.2 0.156 3 3.3 2.5 ADJ -ADJ 78.7 22.1 0.219 4 3.3 2.5 1.5 ADJ 71.5 28.0 0.281 5 5.0 3.3 2.5 ADJ 66.5 34.8 0.344 6 5.0 3.3 2.5 1.8 59.0 40.2 0.406 7 5.0 3.3 2.5 1.5 53.6 47.5 0.469 8 5.0 3.0 2.5 ADJ 47.5 53.6 0.531 9 5.0 3.0 ADJ ADJ 40.2 59.0 0.594 10 3.3 2.5 1.8 1.5 34.8 66.5 0.656 11 3.3 2.5 1.8 ADJ 28.0 71.5 0.719 12 3.3 2.5 1.8 -ADJ 22.1 78.7 0.781 13 5.0 3.3 1.8 -ADJ 16.2 86.6 0.844 14 5.0 3.3 1.8 ADJ 9.53 93.1 0.906 15 5.0 3.0 1.8 ADJ Short Open 1.000 *V5 and V6 are always adjustable (ADJ). pervisor for this supply generates a reset at exactly 4.75V, however no supervisor is this perfect. The actual reset threshold of a supervisor varies over a specified band; the LTC2930 varies 1.5% around its nominal threshold voltage (see Figure 1) over temperature. The reset threshold band and the power supply tolerance bands should not overlap. This prevents false or nuisance resets when the power supply is actually within its specified tolerance band. The LTC2930 has a 1.5% reset threshold accuracy, so a "5%" threshold is typically set to 6.5% below the nominal input voltage. Therefore, a typical 5V, "5%" threshold is 4.675V. The threshold is guaranteed to lie in the band between 4.750V and 4.600V over temperature. The powered system must work reliably down to the low end of the threshold band, or risk malfunction before a reset signal is properly issued. A less accurate supervisor increases the required system voltage margin and increases the probability of system malfunction. The LTC2930 1.5% specification improves the reliability of the system over supervisors with wider threshold tolerances. 2930fa 7 LTC2930 APPLICATIONS INFORMATION Table 2. Suggested 1% Resistor Values for the ADJ Inputs R1 1% LTC2930 VREF VPG GND R2 1% 2930 F02 Figure 2. Mode Selection Monitor Configuration Select the LTC2930 input voltage combination by placing the recommended resistive divider from VREF to GND and connecting the tap point to VPG, as shown in Figure 2. Table 1 offers recommended 1% resistor values for each of the 16 modes. The last column in Table 1 specifies optimum VPG/VREF ratios ( 0.01), when configuring with a ratiometric DAC. At power-up, once V1 or V2 reaches 2.4V, the monitor enters a setup period of approximately 150s. During the setup time, the voltage on the VPG pin is sampled and the monitor is configured to the desired input combination. The comparators are enabled and supply monitoring begins. Do not add capacitance to the VPG pin. VTRIP LTC2930 R3 1% V3, V4, V5 OR V6 R4 1% VSUPPLY (V) VTRIP (V) R3 (k) R4 (k) 12 11.25 2150 100 10 9.4 1780 100 8 7.5 1400 100 7.5 7 1300 100 6 5.6 1020 100 5 4.725 845 100 3.3 3.055 511 100 3 2.82 464 100 2.5 2.325 365 100 1.8 1.685 237 100 1.5 1.410 182 100 1.2 1.120 124 100 1 0.933 86.6 100 0.9 0.840 68.1 100 *See Figure 3. Table 3. Suggested 1% Resistor Values for the -ADJ Inputs VSUPPLY (V) VTRIP (V) R3 (k) R4 (k) -2 -1.87 187 121 -5 -4.64 464 121 -5.2 -4.87 487 121 -10 -9.31 931 121 -12 -11.30 1130 121 *See Figure 4. + - R3 VTRIP = 0.5V * 1+ R4 0.5V 2930 F03 Figure 3. Setting the Positive Adjustable Trip Point Using The Adjustable Thresholds The reference inputs on the V3 and/or V4 comparators are set to 0.5V when the positive adjustable modes are selected (Figure 3). The reference inputs on the V5 and V6 comparators are always set to 0.5V. The tap point on an external resistive divider, connected between the positive voltage being sensed and ground, is connected to the high impedance, adjustable inputs (V3, V4, V5, V6). Calculate the trip voltage from: In the negative adjustable mode, the reference level on the V4 comparator is connected to ground (Figure 4). The tap point on an external resistive divider, connected between the negative voltage being sensed and the VREF pin, is VREF LTC2930 R4 1% V4 R3 1% VTRIP 2930 F04 Figure 4. Setting the Negative Adjustable Trip Point 2930fa 8 LTC2930 APPLICATIONS INFORMATION connected to the high impedance adjustable input (V4). VREF provides the necessary level shift required to operate at ground. The negative trip voltage is calculated from: VTRIP = -VREF * R3 ;V = 1.210V Nominal R4 REF In a negative adjustable application, the minimum value for R4 is limited by the sourcing capability of VREF (1mA). With no other load on VREF, R4 (minimum) is: 1.210V = 1.210k 1mA Tables 2 and 3 offer suggested 1% resistor values for various positive and negative supply adjustable applications assuming 5% monitor thresholds. Although all six supply monitor comparators have builtin glitch immunity, bypass capacitors on V1 and V2 are recommended because the greater of V1 or V2 is also the VCC for the device. Filter capacitors on the V3, V4, V5 and V6 inputs are allowed. Power-Down On power-down, once any of the monitor inputs drops below its threshold, RST is held at a logic low. A logic low of 0.4V is guaranteed until both V1 and V2 drop below 1V. If the bandgap reference becomes invalid (VCC < 2V typical), the LTC2930 will enter the 150s setup period when VCC rises above 2.4V max. Selecting the Reset Timing Capacitor The reset timeout period is adjustable in order to accommodate a variety of microprocessor applications. The reset timeout period, tRST, is adjusted by connecting a capacitor, CRT, between the CRT pin and ground. The value of this capacitor is determined by: CRT = tRST = 500 [pF / ms] * tRST 2M Leaving the CRT pin unconnected generates a minimum reset timeout of approximately 25s. Maximum reset timeout is limited by the largest available low leakage capacitor. The accuracy of the timeout period is affected by capacitor leakage (the nominal charging current is 2A) and capacitor tolerance. A low leakage ceramic capacitor is recommended. OR-ed System Reset In Figure 5, two LTC2930s are configured to monitor 11 supply voltages simultaneously. The unused adjustable input pin is tied to the V1 input. The open-drain RST outputs are OR-tied and pulled up to 5V through a 10k resistor. RST pulls high 94ms after all the inputs are above the threshold voltages. Should a reset event occur on either LTC2930, both RST outputs pull low. Similarly, if the manual reset pushbutton is pressed, both RST outputs also pull low. Using a Pushbutton On/Off Controller with the LTC2930 In Figure 6, the LTC2950-1 pushbutton controller powers a system on and off. The system starts after the pushbutton is pressed, which brings the LTM4600's RUN pin high. Subsequently, the LTM4600 generates a 5V output which applies power to each of the four DC/DC converters. The LTC2930 is configured to mode 13 (see Table 1). The voltages monitored are 5V, 3.3V, 1.8V, -5.2V, 2.5V and 12V. If the KILL input is not driven high within 512ms of a valid turn-on event, EN pulls low shutting down the system. If the external 12V supply drops below 9.6V, EN pulls low, powering down the LTM4600 and subsequent circuitry. An external 4.7nF capacitor sets the 9.4ms reset timeout period. Therefore, 9.4ms after the last supply is above threshold, RST pulls high. The reset timing capacitor must be chosen to keep the reset timeout period below 512ms. Otherwise, the KILL timer will expire and shut down the system. Pressing the pushbutton after the system is powered initiates the power off sequence. An interrupt is set, bringing EN low immediately and disabling the LTM4600. 2930fa 9 LTC2930 APPLICATIONS INFORMATION 5V 10k 5V 3V 12V 3.3V 1.8V -5.2V 1V 0.9V 8V 6V V1 68.1k 1% 86.6k 1% 487k 1% 0.1F 1020k 1% V2 V3 RST V4 1400k 1% V1 2150k 1% V2 V3 0.1F V6 V6 121k 1% 100k 1% 100k 1% RESET LTC2930 V5 V5 R1A 16.2k 1% RST V4 LTC2930 MR VREF VPG MR 10k** GND 100k 1% CRT MANUAL RESET PUSHBUTTON CRT 47nF R2A 86.6k 1% 100k 1% R1B 100k40.2k 1% 1% VREF VPG GND CRT CRT 47nF R2B 59k 1% tRST = 94ms 2930 F05 **OPTIONAL FOR EXTENDED ESD TOLERANCE Figure 5. OR-ed System Reset 12V (9.6V THRESHOLD) LTM4600 VIN VOUT RUN 5V 5V VIN LT3028 VOUT 3.3V 10k 3.3V SHDN EN VIN LTC2950-1 VIN INT PB KILL LT3028 VOUT 1.8V 1.8V SHDN SYSTEM LOGIC LTC3704 VIN VOUT -5.2V -5.2V RUN/UVLO VIN LT3028 VOUT 2.5V 2.5V SHDN 10k 2930 F06 V1 365k 1% 487k 1% 1500k 1% V2 RST V3 SYSTEM RESET V4 LTC2930 V5 V6 MR 100k 1% 0.1F 100k 1% 121k 1% VREF R1 16.2k 1% R2 86.6k 1% VPG CRT GND 4.7nF tRST = 9.4ms Figure 6. Using a Pushbutton On/Off Controller with the LTC2930 2930fa 10 LTC2930 PACKAGE DESCRIPTION DD Package 12-Lead Plastic DFN (3mm x 3mm) (Reference LTC DWG # 05-08-1725 Rev A) 0.70 p0.05 3.50 p0.05 2.10 p0.05 2.38 p0.05 1.65 p0.05 PACKAGE OUTLINE 0.25 p 0.05 0.45 BSC 2.25 REF RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS APPLY SOLDER MASK TO AREAS THAT ARE NOT SOLDERED 3.00 p0.10 (4 SIDES) R = 0.115 TYP 7 0.40 p 0.10 12 2.38 p0.10 1.65 p 0.10 PIN 1 NOTCH R = 0.20 OR 0.25 s 45o CHAMFER PIN 1 TOP MARK (SEE NOTE 6) 0.200 REF 0.75 p0.05 6 1 0.23 p 0.05 0.45 BSC 2.25 REF 0.00 - 0.05 (DD12) DFN 0106 REV A BOTTOM VIEW--EXPOSED PAD NOTE: 1. DRAWING IS NOT A JEDEC PACKAGE OUTLINE 2. DRAWING NOT TO SCALE 3. ALL DIMENSIONS ARE IN MILLIMETERS 4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE 5. EXPOSED PAD AND TIE BARS SHALL BE SOLDER PLATED 6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE TOP AND BOTTOM OF PACKAGE 2930fa Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 11 LTC2930 TYPICAL APPLICATION Five Supply Monitor, 5% Threshold (3.3V, 1.5V, 1.2V, 1V, 0.9V) 3.3V 1.5V 1.2V 1V 0.9V 68.1k 1% 86.6k 1% 124k 1% V1 V2 V3 0.1F V4 RST SYSTEM RESET LTC2930 V5 V6 MR 100k 1% 100k 1% 100k 1% R1 71.5k 1% VREF VPG GND CRT PUSHBUTTON RESET CRT 47nF R2 28k 1% 2930 TA02 tRST = 94ms RELATED PARTS PART NUMBER DESCRIPTION COMMENTS LTC1326 Micropower Triple Supply Monitor for 5V/2.5V, 3.3V and ADJ 4.725V, 3.118V, 1V Threshold (0.75%) and ADJ LTC1728 Micropower Triple Supply Monitor with Open-Drain Reset 5-Lead SOT-23 Package LTC2900 Programmable Quad Supply Monitor Adjustable Reset, 10-Lead MSOP and DFN Packages LTC2901 Programmable Quad Supply Monitor Adjustable Reset and Watchdog Timer LTC2902 Programmable Quad Supply Monitor Adjustable Reset and Tolerance (5%, 7.5%, 10%, or 12.5%) LTC2903 Precision Quad Supply Monitor 6-Lead SOT-23 Package LTC2904-LTC2907 Three-State Programmable Precision Dual Supply Monitor 8-Lead SOT-23 and DFN Packages LTC2908 Precision Six Supply Monitor (Four Fixed & Two Adjustable) 8-Lead TSOT-23 and DFN Packages LTC2909 Precision Triple/Dual Input UV, OV and Negative Voltage Monitor Shunt Regulated VCC Pin, Adjustable Threshold and Reset, 8-Lead SOT-23 and DFN Packages LTC2910 Precision Octal Positive/Negative Voltage Supply Monitor 16-Lead SSOP and 5mm x 3mm DFN Packages, H-Grade Temperature Range LTC2912-LTC2914 Single/Dual/Quad UV and OV Voltage Monitors Separate VCC Pin, Adjustable Reset Timer, H-Grade Temperature Range LTC2915-LTC2918 Single Supply Monitor with 27 Pin-Selectable Thresholds Manual Reset, Watchdog, TSOT-8/MSOP-10 and 3mm x 2mm DFN Packages, H-Grade Temperature Range LTC2928 Quad Power Supply Sequencer and Supervisor Easily Configure Power Management without Software, 36-Lead 5mm x 7mm QFN and SSOP Packages LTC2931 Configurable Six Supply Monitor with Individual Comparator Outputs Adjustable Reset and Watchdog Timers, TSSOP-20 Package LTC2932 Configurable Six Supply Monitor with Individual Comparator Outputs Adjustable Reset Timer and Tolerance, TSSOP-20 Package, Pin-Selectable Tolerance (5%, 7.5%, 10%, or 12.5%), Reset Disable for Margining 2930fa 12 Linear Technology Corporation LT 0308 REV A * PRINTED IN USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 FAX: (408) 434-0507 www.linear.com (c) LINEAR TECHNOLOGY CORPORATION 2008