Safety Mats & Area Guarding UMQ Series UMQ Rev. 4.11 Quick-Disconnect Universal Safety Mat System Heavy-Duty Four-Wire Presence Sensing Mats with Removable Cable, Category 3 Controllers and Perimeter Trim Patented Connector System * When UMQ series mats are combined with an MC3, MC4 or MC6 controller (with complete diagnostics), the result is a system that meets the standard EN 1760-1:1998 and is entitled to display the CE mark. See below for an overview of the various components. F UMQ Series Mat * Fork lift traffic of 270 lbs. per square inch * IP67 rated * Mat flammability self extinguishing, meets UL94VO * Single-piece molded construction * Black or yellow color * Damage to cables during installation is eliminated by installating cables after mat installation * Easy cable replacement * Six cable location options offer the ability to configure where cable exits Controllers * Safety category 3 devices * DIN-rail mount (MC3) * NEMA controllers (MC4, MC6) * 24 VDC or with universal power supply 100 to 240 VAC Trim * Two-part perimeter and joining trim simplifies installation and provides a custom appearance * Two options for trim kit corners: Mitered and molded C US Description An Omron STI Quick-Disconnect Universal Mat system (UMQ series mat combined with an MC3, MC4 or MC6) offers a simple method for guarding personnel around hazardous machines. A Quick-Disconnect Universal Mat system offers freedom, flexibility, and reduced operator fatigue when compared with traditional guarding methods such as interlocked fences, pullback restraints or perimeter barriers. Full visibility and access to the work area is maintained. There is no need to worry about personnel forgetting to replace mechanical barriers or close gates. Omron STI UMQ Series safety mat incorporates a design that features a cable quick disconnect located on the mat. This allows the cable to be attached after the mat is installed in order to minimize damage to the cable during installation. The new patented connector is designed and tested to meet IP67 requirements. How the System Works The operation of a Quick-Disconnect Universal Mat system is easy to understand. The mat is a simple, normally open switch. When a specified minimum weight is applied to the mat the "switch" closes. This sends a signal to the controller which, in turn, sends a stop signal to the guarded machine. Each mat presents four wires to the controller. This provides the redundancy required to monitor the wiring for open circuits due to incorrect wiring or physical damage to the wires. In order to meet many national safety regulations, Omron STI offers trim to secure the mat to the floor so that it cannot be easily relocated and therefore become ineffective. F2 Omron Scientific Technologies, Inc. USA Tel. 1/888/510-4357 Canada Tel. 1/866/986-6766 For the Latest Information On the Internet: www.sti.com UMQ Series Safety Mats & Area Guarding Mat Specifications Mechanical Mat Cover Material: Mat Type: Mode: Activation Force: Maximum Load: Mechanical Life: Mat Cable: Mat Weight: Environmental Protection: Operating Temperature: Mat Flammability: Operating Humidity: Mat Chemical Resistance*: PVC Normally open SPST, four-wire Pressure Sensitive Detects adults > 30 kg (66 lbs) (8.5 lbs/in.2) Static Load: 122.5 kg/in.2 (270 lbs/in.2) Rolling Load: 122.5 kg/in.2 (270 lbs/in.2) 1 x 106 operations 18-gauge, 4-conductor, 16-strand, 300 VAC, with MC12DC male single key connector; 5 m or 10 m long Approx. 24.4 kg/m2 (5 lbs/ft.2) IP67 -37 to 66C (-35 to 150 F) Self extinguishing, meets UL 94VO 0-100% RH Water: Excellent Mineral Acids: Good/Excellent Organic Acids: Good/Excellent Alcohols: Good Aldehydes: Good/Excellent Caustics: Good/Excellent Petroleum Solvents: Good Organic Solvents: Poor Chlorinated Solvents: Poor *40 minute exposure at 23C (74F) specifications For and dimensions on the MC Controllers, see page F13 F Compliance Conforming to Standards: ANSI/RIA 15.06-1999 (R2009), ANSI B11.19-2010, OSHA 1910.21(b), CSA Z432-04 Approvals: When used with an MC3, MC4 or MC6 controller the UMQ series safety mats comprise a system which has been EC type examined to the requirements of category 3, EN 954-1 and EN1760-1:1998. Specifications are subject to change without notice. Mat Selection Multiple UMQ series mat sizes are offered. A system can easily be configured to meet almost any guarding requirement. Standard Mat Sizes Widths 12 to 48 in. Lengths 12 to 72 in. Metric Mat Sizes Widths 500 to 1200 mm Lengths 500 to 1800 mm Custom Mat Sizes Widths From 8 in. up to 48 in. (0.5 in. increments) Lengths From 8 in. up to 72 in. (0.5 in. increments) specific mat sizes, For see page F10 Omron Scientific Technologies, Inc. USA Tel. 1/888/510-4357 Canada Tel. 1/866/986-6766 For the Latest Information On the Internet: www.sti.com F3 UMQ Series Trim Selection Applications Several choices are available in trim selection and can be customized to a specific application. Presence sensing safety mats are used to monitor an entire hazardous area. They offer flexibility, quick access and may frequently be the most economic choice. Other options for perimeter guarding include interlocked barrier guards and safety light curtains. However, personnel can become trapped inside a barrier guard and safety light curtains only monitor the perimeter, not the hazardous area inside. Additionally, mats can also simplify routine tasks such as machine setup, maintenance and repair. Applications can be found throughout industry and typically include the following areas: * Welding Robots * Assembly Machinery * Material Handling * Packaging Machinery * Punches * Presses * Robotic Work Cells Two-Part Ramp Trim with Yellow PVC Cover This trim simplifies routing of cables and replacement of damaged mats. To position the mats correctly, place all of the mats in the approximate position, place the joining trim between the mats, then temporarily place the cover on the joining trim. Square the mats by sliding the ramp trim under the mats. When all of the mats are correctly positioned, anchor the perimeter trim to the floor. After the wires have been routed, a rugged cover of highly visible, safety yellow PVC is snapped into place. Corners can either be mitered or be Omron STI's exclusive molded corners. (See illustrations on this page.) Two-Part Ramp Trim with Aluminum Cover F This trim is the same as above except that the PVC cover is replaced with an aluminum cover that is attached by screws to the base. (See the Dimensions Section of this datasheet for details.) Two-Part Active Joining Trim Similar in concept to the two-part ramp trim, this trim provides an "active" joint where the perimeters of two mats adjoin each other. When a person steps on the surface cover of the active joining trim, the Universal Mat system will detect their presence and send a stop signal to the guarded machine. Aluminum Blunt Trim Used to finish off the edge of a mat installation near a wall or machine. Helps hold mats in place. Aluminum Ramp Trim This single part aluminum ramp trim is available for areas where the two part ramp trim may not be suitable. Molded Corners Eliminates the need to miter the corners of perimeter trim. Designed to mate with Omron STI two-part ramp trim. PVC Trim Cover Aluminum Floor F4 Safety Mats & Area Guarding Omron Scientific Technologies, Inc. USA Tel. 1/888/510-4357 Canada Tel. 1/866/986-6766 For the Latest Information On the Internet: www.sti.com UMQ Series Safety Mats & Area Guarding Trim Dimensions (mm/in.) Outside Molded Corner Trim Model UMOC 2-Part Joining Trim (Base and Cover) 58.42 2.300 30.58 1.204 1.02 0.040 17.02 0.670 35.81 1.410 14.1 0.555 72.39 2.850 101.6 4.000 58.42 2.300 94.62 3.725 94.62 3.725 72.39 2.850 30.58 1.204 2-Part Joining Trim: PN 43222-0096 Joining Trim Aluminum Base: PN 32592 Joining Trim Cover Black: PN 32591 Joining Trim Cover Yellow: PN 32591-0010 2-Part Ramp Trim with PVC Cover (TKM) Molded Outside Corner: PN 25836 Inside Molded Corner Trim Model UMIC 21.89 0.862 23.1 0.910 F 11.8 0.47 58.9 2.32 57.48 2.263 91.4 3.60 72.39 2.850 94.62 3.725 57.48 2.263 18.4 0.72 Aluminum Base & PVC Cover: PN 43123-0096 Aluminum Base: PN 32667 PVC Cover: PN 32668 2-Part Ramp Trim with Aluminum Cover (TKAT) 94.62 3.725 72.39 2.850 58.9 2.32 21.89 0.862 Molded Inside Corner: PN 25837 Aluminum Base & Aluminum Cover: PN 43123-1096 Aluminum Base: PN 32667 Aluminum Cover: PN 26441 Blunt Trim 10.8 0.425 Aluminum Single Part Ramp Trim (TKA) 13.72 Ref 0.540 25.4 Ref 1.00 10.64 0.419 13.72 0.540 Blunt Trim: PN 43223-0096 19 Ref 13.72 Ref 0.540 19.53 0.769 63.50 Ref 2.500 9.35 0.367 7.59 Ref 0.299 Aluminum Ramp Trim: PN 43224-0096 Omron Scientific Technologies, Inc. USA Tel. 1/888/510-4357 Canada Tel. 1/866/986-6766 For the Latest Information On the Internet: www.sti.com F5 UMQ Series Safety Mats & Area Guarding Mat Dimensions (mm/in.) Two-Part Trim with PVC Cover and Mitered Corners (TKM) Slide Alum Base Under Mat PVC Trim Cover MAT FASTENING DETAIL Safety Mat Screw Aluminum Trim Base 12.7 0.50 (Ref) 56.79 2.236 Anchor 50.8 2.00 4-Cond Cable with MC12DC Male Single Key 4-Term Connector 25.4 1.00 45 F L = Mat Length (PVC Trim Cvr) A = L + (Aluminum 137.4 B=L+ Trim Base) 5.41 609.6 Shown 24.0 114.8 4.52 104.5 4.115 (Ref) 724.4 Shown 28.52 Cable Conduit Drill Holes in Groove on Boss (#8 x 1.25" Screw) 746.8 Shown. TOL = - 0.381 / +0 29.41 - 0.015 / +0 STI To Cut Alum Trim "Rib" 25.4 (1.00) Section Here Two-Part Trim with PVC Cover and Molded Corners (TKC) Safety Mat PVC Trim Cover Corner Slide Alum Base Under Mat MAT FASTENING DETAIL Screw Aluminum Trim Base 12.7 0.50 (Ref) 56.79 2.236 4-Cond Cable with MC12DC Male Single Key 4-Term Connector 50.8 TOL = - 0.381 / +0 2.00 - 0.015 / +0 50.8 TOL = - 0.381 / +0 (Alum Base) B = L 2.00 - 0.015 / +0 (PVC Trim Cvr) A = L - 104.5 4.115 (Ref) L = Mat Length 138.2 (Overall Length) C = L + 5.44 F6 Omron Scientific Technologies, Inc. USA Tel. 1/888/510-4357 Canada Tel. 1/866/986-6766 STI To Cut Alum Trim "Rib" 25.4 (1.00) Section Here For the Latest Information On the Internet: www.sti.com Anchor 50.8 2.00 25.4 1.00 Cable Conduit Drill Holes in Groove on Boss (#8 x 1.25" Screw) UMQ Series Safety Mats & Area Guarding Mat Dimensions (continued) (mm/in.) Two-Part Trim with Aluminum Cover and Mitered Corners (TKAT) Slide Alum Base Under Mat Aluminum Trim Cover MAT FASTENING DETAIL Safety Mat Aluminum Trim Base 12.7 0.50 (Ref) 56.79 2.236 50.8 2.00 4-Cond Cable with MC12DC Male Single Key 4-Term Connector 609.6 Shown 24.0 L = Mat Length 114.8 4.52 (Alum Trim Cvr) A = L + 25.4 1.00 (Aluminum 137.4 746.8 Shown. TOL = - 0.381 / +0 B=L+ Trim Base) 5.41 29.41 - 0.015 / +0 Cable Conduit Note: Use Groove for Hole Location Guide O7.14 0.281 104.5 4.115 (Ref) 724.4 Shown 28.52 SS Flat Head Phillips Thrd Cutting 6-32 Thread, 3/8" Long Screw F O3.71 0.146 STI To Cut Alum Trim "Rib" 25.4 (1.00) Section Here Single-Part Trim Aluminum Trim (TKA) Aluminum Trim Ramp 12.7 0.50 (Ref) Safety Mat 25.4 1.00 25.4 (1.0) Section of Rib Removed 101.6 4.00 (Ref) 50.8 2.00 Note 1 4-Cond Cable with MC12DC Male Single Key 4-Term Connector 45 56.79 2.236 L = Mat Length (Alum Trim) A = L + MAT FASTENING DETAIL 30.2 1.19 (Ref) Screw (90705) 27.7 1.09 (Ref) Anchor (90706) Cable Conduit Drill and Countersink Holes in Groove for (8-32 x 1.25" Screw) 127.3 TOL = - 0.381 / +0 5.01 - 0.015 / +0 STI To Cut Alum Trim "Rib" 25.4 (1.00) Section Here Omron Scientific Technologies, Inc. USA Tel. 1/888/510-4357 Canada Tel. 1/866/986-6766 For the Latest Information On the Internet: www.sti.com F7 UMQ Series Mat Measurement Mat Dimension - Base = Top Surface Dimension + 11.2 (0.44 ) i.e. Top Mat Dimension = 305 (12.00), Mat Base = 316 (12.44) Mat Dimension - Top Surface 50.8 2.00 Mat Cable Exit Location A Mat Cable exits on the side indicated by the first dimension in the model number i.e. UM5-1254, Cable exits 12" dimension i.e. UM5-4824, Cable exits 48" dimension F Pin Out Connector UMQ5, UMQ10, Integral UM Mat Cables Index/Keyway #20 Pin Contact (4 places) White Blue White Blue Index/Keyway 2 3 2 1 Brown #20 Pin Contact (44places) Black 1 3 Mating/Face View 4 Brown Black Male Connector Mating/Face View UM-Y-2-1 "Y" Connector Female B 4 Black 1 Brown 20 0.79 Wire Diagram Wire Diagram 3 Red/Black Female B 2 Black Red/White 4 1 Brown Female A 3 Red/Black 1 2 Red/White 4 Female A 3 Blue 2 1 White 4 Male Connector Male 20 0.79 4 1 Male 3 4 2 1 3 2 49.9 1.96 49.9 1.96 Rear Side 3 Blue 2 White Rear Side F8 Omron Scientific Technologies, Inc. USA Tel. 1/888/510-4357 Canada Tel. 1/866/986-6766 For the Latest Information On the Internet: www.sti.com Safety Mats & Area Guarding UMQ Series Safety Mats & Area Guarding Custom Mats and Trims Omron STI makes ordering custom mats and trims easy. Simply send us a sketch of your layout including dimensions. Make note of where you want ramp trim or blunt trim. We'll work from your sketch to create a detailed drawing of your specifications. Step 1: Customer Sends a Sketch Step 2: A Quote Drawing with Dimensions is Created Example Molded Outside Corner UM4234SPCOL 1947.2 76.66 2 Part Ramp Trim CUSTOM MAT STANDARD MAT UM4236 685.8 27.00 2 Part Joining Trim 1162.1 45.75 362 14.25 209.6 8.25 Molded Inside Corner 450.9 17.75 292.1 11.50 277.1 10.91 F 106.4 16.00 Blunt Trim 1011.2 39.81 Step 3: When the Order is Placed, A Detailed Layout Showing all Components of the Trim System is Made E 1851.9 72.91 B 57.2 2.25 41.4 1.63 41.4 1.63 25.4 1.00 27.9 1.10 38.1 1.50 673.1 26.50 38.1 1.50 57.2 2.25 108 4.25 B A N C E M 1162.1 45.75 M 187.5 7.38 339.6 13.37 K 69.1 2.72 L 25.4 1.00 56.4 2.22 D K J 25.4 1.00 H G 23.1 0.91 C UM4236 590.6 23.25 Machined Cut Out (2 places) 108 4.25 UM4234SPCOL N 41.4 1.63 41.4 1.63 25.4 1.00 27.9 1.10 F 28.7 1.13 12.7 0.50 Machined Cut Out (2 places) D 940.6 37.03 Omron Scientific Technologies, Inc. USA Tel. 1/888/510-4357 Canada Tel. 1/866/986-6766 For the Latest Information On the Internet: www.sti.com F9 UMQ Series Safety Mats & Area Guarding Ordering Ordering a UMQ Mat System Standard Mat Ordering Code: A Quick Disconnect Universal Mat System contains at least one mat, a 5 m or 10 m cable, sufficient perimeter and joining trim and a controller. For multiple mat installations using the MC3 controller, the mats are connected in series to the controller. This may be done using the UMDB6 wiring accessory. When using the MC4 or MC6 controllers, six mats may be connected directly to the controller. Each component of Quick Disconnect Universal Mat system must be ordered individually Mats are available in black or yellow. Yellow mats are denoted by placing a "Y" in the ordering code. The cable location is specified by letter code at the end of the ordering number. Cables must be ordered separately. To order a Quick-Disconnect Universal Mat System, simply fill in the fields in the model number sequence given. F UM Mats vs. UMQ Mats UM Prior to the development of the UMQ Mat with QuickDisconnect cable, the UM Series Mat was the standard mat supplied by Omron STI. The UM Mats are available with integral cables in 5 m or 10 m lengths. These integral cables are not removable. UM mats are still available and can be ordered in black or yellow with required perimeter and joining trim. For detailed specifications and ordering information on the Universal Mat System, please visit our website at www.sti.com and enter 'UM" in the SpeedSPEC search box. ___ - ___ ___- ___ 1 2 3 6 Example: UMQ-2460-A This example is a 24 x 60 in. standard black mat with cable location A. Metric Mat Ordering Code: ___ - ___ - ___ - ___ 1 4 5 6 Example: UMMQ-0500-0500-B This example is a 500 x 500 mm black metric quick disconnect mat with cable coming out at location B. 1 Information required. Represents mat type and color. Designator Description UMQ Standard black mat UMYQ Standard yellow mat* UMMQ Metric black mat UMMYQ Metric yellow mat* Notes: *Mats will take the largest dimension as the first dimension up to the 48 in. width (i.e. a mat ordered as 36 x 48 will be made as 48 x 36). 2345 Information required. Represents the mat size. Dimensions are for active mat area. Mats are an additional 0.5 in. (12 mm) in each dimension. Choose one value from each column. 2 Standard Mat Widths in 3 Standard Mat Lengths in Inches Designator Inches Designator 12 12 18 18 24 24 30 30 36 36 42 42 48 48 54 60 66 72 Special Standard Sizes* Special inch sizes are available in increments of 0.5 in., with a minimum width or length of 8 in. 4 Metric Mat Widths in mm 5 Metric Mat Lengths in mm Designator Designator 0500 (500 mm/19.7 in.) 0500 (500 mm/19.7 in.) 0750 (750 mm/29.5 in.) 0750 (750 mm/29.5 in.) 1000 (1000 mm/39.4 in.) 1000 (1000 mm/39.4 in.) 1200 (1200 mm/47.2 in.) 1250 (1250 mm/49.2 in.) 1500 (1500 mm/59.1 in.) 1750 (1750 mm /68.9 in.) 1800 (1800 mm/70.9 in.) *Please consult Omron STI for mat sizes not listed in the above tables. = Highlighted Rapid Delivery products are available for shipment today or within THREE days. F10 Omron Scientific Technologies, Inc. USA Tel. 1/888/510-4357 Canada Tel. 1/866/986-6766 For the Latest Information On the Internet: www.sti.com UMQ Series Safety Mats & Area Guarding Ordering (continued) 6 Information required. Represents cable location. See Rapid Delivery Products diagram below. The following models are readily available for shipment today or at least within 3 days. Please consider these for all new applications. Cable Location Description Model Number Part Number A Bottom left corner of first mat dimension, 2 in. from top surface of the left edge to center of cable exit B Bottom center of first mat dimension UMQ-1260-A 70220-1002 12 x 60 in. Universal Black Mat C Bottom right corner of first mat dimension, 2 in. from top surface of the right edge to center of cable exit UMQ-1872-A 70220-1010 18 x 72 in. Universal Black Mat UMQ-2412-A 70220-1011 24 x 12 in. Universal Black Mat D Bottom right corner of second mat dimension, 2 in. from top surface of the bottom edge to center of cable exit UMQ-2418-A 70220-1012 24 x 18 in. Universal Black Mat UMQ-2424-A 70220-1013 24 x 24 in. Universal Black Mat UMQ-2460-A 70220-1015 24 x 60 in. Universal Black Mat UMQ-2472-A 70220-1017 24 x 72 in. Universal Black Mat UMQ-3030-A 70220-1021 30 x 30 in. Universal Black Mat UMQ-3060-A 70220-1023 30 x 60 in. Universal Black Mat UMQ-3072-A 70220-1025 30 x 72 in. Universal Black Mat UMQ-3612-A 70220-1026 36 x 12 in. Universal Black Mat UMQ-3624-A 70220-1028 36 x 24 in. Universal Black Mat UMQ-3636-A 70220-1030 36 x 36 in. Universal Black Mat UMQ-3654-A 70220-1031 36 x 54 in. Universal Black Mat UMQ-3660-A 70220-1032 36 x 60 in. Universal Black Mat UMQ-3672-A 70220-1034 36 x 72 in. Universal Black Mat UMQ-4224-A 70220-1037 42 x 24 in. Universal Black Mat UMQ-4236-A 70220-1039 42 x 36 in. Universal Black Mat UMQ-4254-A 70220-1041 42 x 54 in. Universal Black Mat UMQ-4260-A 70220-1042 42 x 60 in. Universal Black Mat UMQ-4824-A 70220-1047 48 x 24 in. Universal Black Mat UMQ-4836-A 70220-1049 48 x 36 in. Universal Black Mat UMQ-4848-A 70220-1051 48 x 48 in. Universal Black Mat UMQ-4866-A 70220-1054 48 x 66 in. Universal Black Mat UMQ-4872-A 70220-1055 48 x 72 in. Universal Black Mat E Center of second mat dimension F Top right corner of second mat dimension, 2 in. from top surface of the top edge to center of cable exit Notes: Mats with both dimensions equal will only have "A", "B", and "C" cable locations available. F Length (2nd Dimension) E Width (1st Dimension) A B Cable locations shown are for rectangular mats only. D C Description F = Highlighted Rapid Delivery products are available for shipment today or within THREE days. Omron Scientific Technologies, Inc. USA Tel. 1/888/510-4357 Canada Tel. 1/866/986-6766 For the Latest Information On the Internet: www.sti.com F11 UMQ Series Safety Mats & Area Guarding Ordering (continued) Ordering Perimeter Trim for a Single Mat** Ordering Cables To order Perimeter Trim for a single mat, simply fill in the fields in the model number sequence given below. Cables should be ordered separately. Standard Perimeter Trim Ordering Code: ___ - ___ ___- ___ Example: TKM-1266-E 7 2 3 Model No. Description UMQ5 Cable 5 m quick disconnect cable UMQ10 Cable 10 m quick disconnect cable This example is a trim kit with mitered corners to fit a 12 x 66 in. standard mat with cable coming out at location E. 6 Metric Perimeter Trim Ordering Code: ___ - ___ - ___ - ___ Example: MTKM-0500-0500-E 7 4 5 6 This example is a trim kit with mitered corners to fit a 500 x 500 mm metric quick disconnect mat with cable coming out at location E. 7 Information required. Represents the corner style used on the trim kits. F Designator TKM Description Standard trim kit, 2-part mitered corners with PVC top cover TKAT Standard trim kit, 2-part mitered corners with aluminum top cover TKC Standard trim kit, 2-part with molded corners with PVC top cover TKA Standard trim kit, single part aluminum ramp trim (mitered only) MTKM Metric trim kit with mitered corners MTKC Metric trim kit with molded corners MTKAT is available upon request. specifications and dimensions For on the MC Controllers, see page F13 details on ordering a For custom safety mat, see page F9 details on ordering a trim kit for For a multiple configuation mat, please consult Omron STI. Accessories for Standard and Metric Sized Mats Model Number UMRT4 UMRT8 UMRT8A UMJS4 UMJS8 UMJTC8Y UMBT4 UMBT8 UMAL UMOC UMIC UMDB-6 UMDB-8 UMDB-10 UMEC-DB6 UMEC-03 UMEC-05 UMEC-10 UMEC-15 UMPMC UM4PRC UM-Y-2-1 UMQ5 UMQ10 F12 Description Weight Bulk two-part ramp trim with yellow PVC cover 1.22 m (48 in.) length 1.5 kg (3.3 lb.) Bulk two-part ramp trim with yellow PVC cover 2.44 m (96 in.) length 3.0 kg (6.6 lb.) Bulk two-part ramp trim with aluminum top 2.44 m (96 in.) length 3.2 kg (7.0 lb.) Bulk two-part active joining trim 1.22 m (48 in.) length 1.4 kg (3.0 lb.) Bulk two-part active joining trim 2.44 m (96 in.) length 2.7 kg (6.0 lb.) Bulk joining trim cover yellow 2.44 m (96 in.) 0.5 kg (1.0 lb.) Bulk blunt trim 1.22 m (48 in.) length 1.1 kg (2.5 lb.) Bulk blunt trim 2.44 m (96 in.) length 2.3 kg (5.0 lb.) Bulk aluminum ramp trim 2.44 m (96 in.) 2.9 kg (6.5 lb.) Molded outside corner Molded inside corner Universal Safety Mat distribution box with 6 mat input connectors and one output connection to the controller Universal Safety Mat distribution box with 8 mat input connectors and one output connection to the controller Universal Safety Mat distribution box with 10 mat input connectors and one output connection to the controller 15 m extension cable (distribution box to controller) for UMDB-8 or UMDB-10 3 m (9 ft.) extension cable for mat or UMDB-6 5 m (16 ft.) extension cable for mat or UMDB-6 10 m (32 ft.) extension cable for mat or UMDB-6 15 m (49 ft.) extension cable for mat or UMDB-6 Panel-mount connector. Allows the controller to accept quick disconnect cable from UM series mats. 4-pin male QD field replacement connector for mat cables "Y" connector, internally connected to allow 2 mats to 1 input to controller or connector 5 m quick-disconnect cable 10 m quick-disconnect cable Omron Scientific Technologies, Inc. USA Tel. 1/888/510-4357 Canada Tel. 1/866/986-6766 For the Latest Information On the Internet: www.sti.com