NOTE: (1) Add suffix "B" for U-bracket or "C" for enclosed i.e. IFC200-45C.
(2) On Output #2 peak current is 12A on +12V, 9A on +15 V and 6A on +24V.
(3) Output #4 is floating. It can be connected externally for positive or negative output.
(4) 200 watts for "C" version with a cover-and-fan assembly. 150 watts for "B" version without moving air (maximum current of output #1 & #2 derated to
70%), or 200 watts with 25 CFM forced air provided by user.
DESCRIPTION
The IFC200 Series is comprised of single and multiple output
models capable of delivering 200 watts of continuous output
power. All models have a power factor better than 0.95 and
have the same mechanical dimension and output pinning
as their corresponding PU200 series models. All
auxiliary outputs have magnetic amplifier
regulators to maintain tight output tolerances.
The units are constructed on a printed circuit
board with a U-bracket for mechanical
support and heat sinking. A cover-and-
fan assembly is optional. All models
meet CISPR22 and FCC Class B
emission limits, and are
approved to UL, CSA, and,
TUV safety standards.
• UNIVERSAL INPUT
• POWER FACTOR CORRECTION
FEATURES
•EN61000-3-2, 3 compliant
•True “universal” input
•Built-in EMI filter
•Short circuit protection
with auto-recovery
•Power Fail Detect (PFD) signal
•100% burn-in at full rated load
•Optional cover-and-fan assembly
•Small size 9.0”x 5.0”x 2.55”
International Power Sources, Inc.
200 WATT
SWITCHING
POWER SUPPLY
NEW
OUTPUT VOLTAGE/CURRENT RATINGS CHART
Output #1 Output #22Output #3 Output #43Maximum
Output
Model Vnom Imin Imax Tol. Vnom Imin Imax Tol. Vnom Imin Imax Tol. Vnom Imin Imax Tol. Power4
IFC200-10 5V 3A 40A 2% N/A N/A N/A 200W
IFC200-12 12V 1.2A 16.7A 2% N/A N/A N/A 200W
IFC200-13 15V 1.0A 13.4A 2% N/A N/A N/A 200W
IFC200-14 24V 0.6A 8.4A 2% N/A N/A N/A 200W
IFC200-16 30V 0.5A 6.7A 2% N/A N/A N/A 200W
IFC200-18 48V 0.5A 4.2A 2% N/A N/A N/A 200W
IFC200-23 +5V 3A 30A 2% +12V 0A 8A 4% N/A N/A 200W
IFC200-24 +5V 3A 30A 2% +15V 0A 6A 4% N/A N/A 200W
IFC200-25 +5V 3A 30A 2% +24V 0A 4A 4% N/A N/A 200W
IFC200-30 +5V 3A 30A 2% +12V 0A 8A 4% -5V 0A 6A 4% N/A 200W
IFC200-31 +5V 3A 30A 2% +12V 0A 8A 4% -12V 0A 4A 4% N/A 200W
IFC200-32 +5V 3A 30A 2% +15V 0A 6A 4% -15V 0A 4A 4% N/A 200W
IFC200-33 +5V 3A 30A 2% +15V 0A 6A 4% -12V 0A 4A 4% N/A 200W
IFC200-40 +5V 3A 30A 2% +12V 0A 8A 4% -12V 0A 4A 4% F 5V 0A 6A 4% 200W
IFC200-41 +5V 3A 30A 2% +15V 0A 6A 4% -15V 0A 4A 4% F 24V 0A 4A 4% 200W
IFC200-42 +5V 3A 30A 2% +12V 0A 8A 4% -12V 0A 4A 4% F 12V 0A 4A 4% 200W
IFC200-44 +5V 3A 30A 2% +12V 0A 8A 4% -15V 0A 4A 4% F 15V 0A 4A 4% 200W
IFC200-45 +5V 3A 30A 2% +12V 0A 8A 4% -12V 0A 4A 4% F 24V 0A 4A 4% 200W
P2 P3
GENERAL SPECIFICATIONS
All specifications are typical at nominal line, full load, and 25⬚C.
Efficiency: 70% minimum on all models
Hold-up time: 12 msec minimum at 110 VAC input
Line regulation: ±0.5% maximum at full load
Inrush current: 20 amps at 115 VAC or 40 amps at
230 VAC at 25⬚C cold start
Withstand voltage: 3000 VAC from input to output
1500 VAC from input to ground
500 VAC from output to ground
Operating temperature: 0⬚C to 70⬚C*
Storage temperature: -40C⬚to +85⬚C
MTBF: 300,000 hours at full load at 25⬚C
ambient; MIL-HDBK-217F
EMI requirements: Meets conduction limits of
a) CISPR 22 (EN 55022) Level B
b) FCC 20780 Level B
Safety requirements: Meets or exceeds:
a) UL 1950
b) CSA C22.2 No. 234
c) IEC 950 (EN60950)
Power Fail Detect: TTL logic high for normal operation
(PFD SIGNAL) and TTL logic low upon loss of input
power. This signal appears at least
1mS prior to the main output dropping
5% below its nominal value. This signal
also provides a minimum delay of 100
mS after the main output is within regulation.
INPUT SPECIFICATIONS
Input voltage: 90 to 264 VAC
Input frequency: 47 to 63 Hz
Input current: 3.6A (rms) for 115 VAC
1.8A (rms) for 230 VAC
OUTPUT SPECIFICATIONS
Output voltage: See Rating Chart
Output current: See Rating Chart
Output power range: See Note #4 on rating chart
Ripple and noise: 2% peak to peak maximum
Overvoltage protection: Provided on output #l only; set at
112-132% of its nominal
output voltage
Overcurrent protection: All outputs protected to short
circuit conditions
Temperature coefficient: All outputs ±0.04%/⬚C maximum
Transient response: Maximum excursion of 4% or
better on all models recovering to
1% of final value within 500us after
a 25% step load change
Cooling: 25 CFM forced air provided on
"C" version; to be provided by user
on "B" version.
* Derate linearly from 100% load at 50°C to 50% load at 70°C
PIN CHART
MECHANICAL SPECIFICATIONS
NOTES:
1. Dimensions shown in inches [mm]
2. Tolerance 0.02 [0.5] maximum
3. Input connector P1 is Beau Inc. P/N
72-5-03C, output connector P2 is
Beau Inc. P/N 72-5-09C. Screws are
#6-32 on 0.375 inch centers.
4. Connector P3 mates with Molex
housing 22-01-1043 and Molex
40445 series crimp terminal.
5. Connector P4 mates with Molex
housing 22-01-1023 and Molex
40445 series crimp terminal.
6. Connector P4 is for DC fan rated
24V/ 0.12A (models IFC200-14,-16,-25)
or 12V/ 0.2A (other models).
7. Weight:
2.8 Lbs. (1.25 Kgs) approx.
for "B" version.
3.3 Lbs. (1.5 Kgs) approx.
for "C" version.
Model PIN 1, 2 3, 4, 5 6 7 8 9 1 2 3 4
IFC200-10, IFC200-12 -SENSE COM OUTPUT OUTPUT OUTPUT +SENSE P.F.D. COM. COM. FAN
IFC200-13, IFC200-14 RET. #1 #1 #1 RET. RET.
IFC200-16, IFC200-18
IFC200-23, IFC200-24 OUTPUT COM. OUTPUT N.C. N.C. N. C. P.F.D. COM. COM. FAN
IFC200-25 #1 RET. #2 RET. RET.
IFC200-30, IFC200-31 OUTPUT COM. OUTPUT OUTPUT N.C. N.C. P.F.D. COM. COM.
IFC200-32, IFC200-33 #1 RET. #2 #3 RET. RET. FAN
IFC200-40, IFC200-41 OUTPUT COM. OUTPUT OUTPUT OUTPUT OUTPUT P.F.D. COM. COM. FAN
IFC200-42, IFC200-44 #1 RET. #2 #3 #4 #4 RET. RET.
IFC200-45 RETURN
Your Source of Power ...
260 Hopping Brook Road, Holliston, MA 01746
TEL: (508) 429-4440 FAX: (800) 226-2100
http://www.intlpower.com
P1
1-Line
2-Neutral
3-Ground
