Click on Series name for product info on aimtec.com Series AMLB-Z Up to 900mA | Step Up LED Driver FEATURES: Step Up DC/DC LED Driver Constant Current Output High Efficiency up to 94% Soft Start 2"x1" Case Package Operating Temperature -40C to +85C Open and Short Circuit LED Protection PWM / Digital & Analog Voltage Dimming Drives LED Strings of up to 48V Models Single output Input Voltage (V) Model AMLB-3615Z AMLB-3625Z AMLB-3630Z AMLB-3635Z 9-36 9-36 9-36 9-36 AMLB-3650Z 9-36 AMLB-3660Z 9-36 AMLB-3670Z 9-36 AMLB-3690Z 20-30 Output Voltage (V) Vo-Vin5V Maximum Rated Current (mA) Max Capacitive Load (F) Efficiency (%) Ripple & Noise (mV p-p) 150 250 300 350 100 100 100 100 90 92 92 92 350 450 450 600 500 47 93 650 600 47 93 650 700 47 94 700 900 47 94 400 14-48 14-48 14-48 14-48 14-45 (Vin:9V-18V) 23-48 (Vin: 18V-36V) 14-38 (Vin:9V-18V) 23-48 (Vin: 18V-36V) 14-32 (Vin:9V-18V) 23-48 (Vin: 18V-36V 25-48 NOTE: All specifications in this datasheet are measured at an ambient temperature of 25C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. Input Specifications Parameters Nominal Typical Voltage range Filter Absolute Maximum Rating Peak Input Voltage time DC/DC ON (Leave open if not used) DC/DC OFF Remote Pin Drive Current Quiescent Input Current in Shutdown mode Analog and PWM Dimming Control (Leave open if unused) (DIM) Analog DIM Input Voltage Rang Analog Adjust Output Current DIM Pin Drive Current PWM Control Voltage Range Limits PWM Recommended Operating Frequency PWM Adjust Output Current Maximum 9-36 20-30 (900mA model) Capacitor Units VDC 38 100 VDC ms <1.5 1.3 8 A ON -Open OFF(shutdown) - 0V VON/OFF 3V (Vin : 9V-32V) (Vin : 32V-36V) mA Absolute Maximum Ratings: 8V 0.4 to 1.7 0-100 <1.5 1.7Vdim5.0 0.3Vdim1.3V V % A V 100Hz-100KHz 1 - 100 (see graph) % Output Specifications Parameters Current Accuracy Output Voltage Range Output Current Short Circuit Protection Over Voltage Protection Under Voltage Protection www.aimtec.com F 051e R12.F Conditions Typical See model table Vout-Vin5V 5 14-48 See model table Automatic Recovery (Cut-off Output) Maximum Cool Start 7.6 % VDC 52.5 Tel: +1 514 620 2722 1 of 7 Units Vdc V Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AMLB-Z Up to 900mA | Step Up LED Driver Output Specifications (continued) Parameters Conditions Typical Maximum Units 50 ms Soft Start Time Under Voltage Lock Out (Module on / off) Temperature Coefficient Ripple & Noise (100 to 700mA) (900mA) 20MHz Bandwidth 7.6 / 6.8 15.6 / 14.6 0.03 See model table VDC %/oC General Specifications Parameters Operating Frequency Operating Temperature Storage Temperature Maximum Case Temperature Thermal Impedance Cooling Humidity Case material Weight Dimensions (L x W x H) MTBF Maximum Soldering Temperature NOTES: Conditions Typical Depending on the model AMLB-3615Z AMLB-3625Z; AMLB-3630Z AMLB-3635Z AMLB-3650Z AMLB-3660Z; AMLB-3670Z AMLB-3690Z 360-380 Maximum Units KHz -40 to +85 -40 to +80 (Vin 9-18V) / -40 to +85 (Vin 18-36V) -40 to +75 (Vin 9-18V) / -40 to +85 (Vin 18-36V) -40 to +70 (Vin 9-18V) / -40 to +80 (Vin 18-36V) -40 to +70 (Vin 9-18V) / -40 to +75 (Vin 18-36V) -40 to +65 -55 to +125 100 Depending on the model +13.7 to +17 Free air convection 95 Non-Conductive Black Plastic (UL94-V0 rated) 38 2.03 x 1.03 x 0.62 inches 51.50 x 26.10 x 15.80 mm > 1 290 000 hrs (MIL-HDBK-217 F at +25 oC/Vin=9V,Vout=38V) 1.5mm from case for 10sec. 260 oC oC oC oC/W % RH g oC 1. To prevent burning out the driver, the output voltage must be 5.0VDC higher than the input voltage 2. Do NOT exceed the maximum power ratings on each model 3. With output ripple being rather low, it is recommended not to increase the additional output capacitor so s not to increase the delay while starting up under cool start conditions 4. This series offers protection in case the output is shorted. After the short occurs, the input current will be cut off and recovers when the short is removed 5. The reference value of under voltage protection (7.6V) means that under the condition of cool start and full discharge of output, the protection starts when input voltage is lower than 7.6V 6. Note: PWM dimming means PWM signals are converted into mimic analog voltage by internal circuits and then do the dimming. The advantage of this approach is to reduce the EMI Safety Specifications Parameters CE, EN 55015, EN 61547, NOTE: Designed to meet EN 55022 Class B, IEC/EN 60950-1 , UL8750, IEC/EN 61347-2-13 Electrostatic Discharge Immunity IEC 61000-4-2 RF, Electromagnetic Field Immunity IEC 61000-4-3 Electrical Fast Transient/Burst Immunity IEC 61000-4-4 Surge Immunity IEC 61000-4-5 RF, Conducted Disturbance Immunity IEC 61000-4-6 Power frequency Magnetic Field Immunity IEC 61000-4-8 Voltage dips, Short Interruptions Immunity IEC 61000-4-11 Agency approvals Standards Pin Out Specifications Pin 1 2 3 4 5 6 Single +Vi DIM ON/OFF -Vi +LED -LED www.aimtec.com F 051e R12.F Description + DC Supply PWM/Analog Dimming Control Remote ON/OFF -DC Supply LED Anode connection LED Cathode connection Tel: +1 514 620 2722 2 of 7 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AMLB-Z Up to 900mA | Step Up LED Driver Operating Temperature Free Air Convection AMLB-3615Z AMLB-3625Z (Vin:18V-36V) AMLB-3630Z (Vin:18V-36V) AMLB-3635Z (Vin: 18V-36V) Output Power (%) 100 AMLB-3650Z (Vin:18V-36V) AMLB-3625Z (Vin:9V-18V) AMLB-3630Z (Vin:9V-18V) 80 60 AMLB-3635Z (Vin:9V-18V) AMLB-3660Z (Vin:18V-36V) AMLB-3670Z (Vin:18V-36V) Safe Operating Area 40 AMLB-3650Z (Vin:9V-18V) AMLB-3660Z (Vin:9V-18V) AMLB-3670Z (Vin:9V-18V) 20 AMLB-3690Z (Vin:20V-30V) 0 70 75 - 40 - 20 0 20 40 60 Ambient Temperature 85 80 100 C Dimensions Mechanical Tolerances Case tolerance 0.5mm or 0.02 inches Pin diameter 1.0 0.05mm or 0.04 0.002 inches Pin Pitch tolerance: 0.35 or 0.014 www.aimtec.com F 051e R12.F Tel: +1 514 620 2722 3 of 7 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AMLB-Z Up to 900mA | Step Up LED Driver EN55022 Class B Filter Suggestion: Application circuit examples: +Vin +LED 1 +Vin 1st LED 5 +LED 1 1 AMLB-Z 5 AMLB-Z 4 -Vin 6 2 DIM 3 PWM/Analog Dimming Control EN 1 4 -Vin Last LED 2 DIM -LED 6 3 PWM/Analog Dimming Control 1 1 1 1 1st LED EN Last LED -LED +Vin +LED 5 1 AMLB-Z 4 -Vin DIM 2 EN 3 ON SW OFF 1st LED 1 6 1 Last LED Vout ON 0V OFF normal -LED AC In 6.5Vac to 25Vac 0.1uF optional SW +Vin 100uF to 330uF + - +LED 1 5 1st LED 1 AMLB-Z 4 6 -Vin 2 AC In www.aimtec.com F 051e R12.F DIM PWM/Analog Dimming Control Tel: +1 514 620 2722 4 of 7 Last LED 3 1 EN -LED Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AMLB-Z Up to 900mA | Step Up LED Driver Under Voltage Protection +Vin +LED 1 1st LED 5 1 AMLB-Z 6 4 -Vin 2 EN 3 DIM Last LED 1 R1 -LED *R1 Value only supplies the reference R1 Under Voltage Protection X 7.6V 12K 10.8V 10K 11.6V 7.5K 13.0V 4.7K 16.5V 3.3K 21.0V 2.7K 24.1V 2.4K 26.2V 2.0K 29.8V 1.8K 32.4V Output Current Adjustment by External DC Control Voltage (VCTRL): +Vin +LED 5 1 0.4V-1.7V 2 DC DIM 4 -Vin +Vin 6 3 Last LED 1 EN GND 1st LED 1 AMLB-Z R1 -LED If Vin is between 9 VDC and 36 VDC it is recommended to use the circuit shown below R2 DIM R1 380K +5v 380K 30K 1 +Vin 1 AMLB-Z 2 VR DIM 200K 0V-1.7V -Vin 3 4 R1 +LED 5 DIM -Vin 4 1st LED 1 AMLB-Z 6 Last LED 3 EN 1 -LED 1 -LED 0 - 10VDC Vin R1 5V 4.7K 12V 18K 24V 43K 36V 62K 1M +Vin 1 0V-1.7V R2 1st LED 1 6 EN DIM 200K 2 TL431 +LED 5 VR +Vin 1 210K 5 1 2 DIM AMLB-Z -Vin 4 6 3 EN www.aimtec.com F 051e R12.F +LED 1st LED 1 -LED Tel: +1 514 620 2722 5 of 7 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AMLB-Z Up to 900mA | Step Up LED Driver Output Current Adjustment by PWM Control: A Pulse Width Modulation (PWM) signal with a duty cycle DPWM can be applied to the DIM pin as shown below. +Vin +LED 1 5V PWM -Vin 4 5 1st LED 1 AMLB-Z 6 0V 2 DIM Last LED 3 1 EN -LED Driving DIM Via Open Collector Transistor The DIM pin can also be driven via an open collector transistor as shown below. Driving the VADJ from a Microcontroller The DIM can be driven from an open drain output of a microcontroller as shown below. www.aimtec.com F 051e R12.F Tel: +1 514 620 2722 6 of 7 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AMLB-Z Up to 900mA | Step Up LED Driver Output Current Adjustment by PWM Control (Dimming): A PWM signal must have a frequency of greater than 100Hz to prevent any visible flicker. Output Current Adjustment by PWM Control (Flash): Output Current vs DIM Voltage AMLB3615Z AMLB3625Z AMLB3630Z AMLB3635Z AMLB3650Z AMLB3660Z AMLB3670Z AMLB3690Z 1,000 900 ILED(mA)(outputcurrent) 800 700 600 500 400 300 200 100 0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.0 11.0 12.0 13.0 14.0 15.0 16.0 17.0 18.0 19.0 20.0 21.0 22.0 23.0 24.0 DIMvoltage(V) NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. 5. Aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 6. This product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate specific safety and regulatory standards other the ones listed in this datasheet. 7. Warranty is in accordance with Aimtec's standard Terms of Sale available at www.aimtec.com. www.aimtec.com F 051e R12.F Tel: +1 514 620 2722 7 of 7 Toll free: + 1 888 9 AIMTEC (924 6832) North America only