LM4921 www.ti.com LM4921 SNAS178E - JULY 2003 - REVISED MAY 2013 Low Voltage I2S 16-Bit Stereo DAC with Stereo Headphone Power Amplifiers and Volume Control Check for Samples: LM4921 FEATURES APPLICATIONS * * * * * * * * 1 2 * * * * * 16-Bit Resolution Stereo DAC I2S Digital Audio Data Serial Interface SPI Serial Interface (Control Register) Volume Control (32 steps; 1.5 dB Increments) Up to 50mW/Channel Stereo Headphone Amplifier Zero Crossing Detection for Silent Attenuation Steps 2.6VDC to 5.0VDC Digital Supply Voltage Range 2.6VDC to 5.5VDC Analog Supply Voltage Range (See (1)) Unity-Gain Stable Headphone Amplifiers Available in the 20-bump DSBGA Package KEY SPECIFICATIONS * * * * (1) PSRR at 217Hz, A/DVDD = 3V, (See Figure 1): 52dB (typ) POUT at AVDD = 3.0V, 32 - < 0.05% THD: 13mW (typ) - < 0.05% THD: 26mW (typ) Supply Voltage Range - DVDD: 2,6V to 5.0V - AVDD: (See (1)) 2.6V to 5.5V Shutdown Current: 1A (typ) Mobile Phones PDAs Portable Electronic Devices DESCRIPTION The LM4921 combines a 16-bit resolution stereo I2S input digital-to-analog converter (DAC) with a stereo headphone audio power amplifier. It is primarily designed for demanding applications in mobile phones and other portable communication device applications. The LM4921 features an I2S serial interface for the digital audio information and a 16-bit SPI serial interface for internal register control and communication. With AVDD and DVDD = 3.0VDC and driving a 32 single-ended load to a 26mWRMS output level the distortion (THD+N) of the LM4921 will be less than 0.5%. The LM4921 also features a programmable 32-step digital volume control accessed through an SPI interface. Boomer audio power amplifiers were designed specifically to provide high quality output power with a minimal amount of external components. It is, therefore, ideally suited for mobile phone and other low voltage applications where minimal power consumption is a primary requirement. The LM4921 features a low-power consumption shutdown mode, and also has an internal thermal shutdown protection mechanism. Best operation is achieved by maintaining 3.0V AVDD 5.0V and 3.0V DVDD 5.0V. 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 2003-2013, Texas Instruments Incorporated LM4921 SNAS178E - JULY 2003 - REVISED MAY 2013 www.ti.com Typical Application DVDD 1PF GNDD DV DD NC + 32: Control Filter 32: LPF 1 - Bit DAC R - Amp + Serial Interface HP_R 100 PF + V REF Clock Logic SPI Control V DD X MCLK/XTAL_IN SPI_ENABLE 100 PF Digital Volume Interpolation SPI_CLK SPI_DATA HP_L Digital Generator BYPASS I2S_LRCLK I2S_CLK L - Amp + GNDX I2S_DATA LPF 1 - Bit DAC XTAL_OUT NC I 2 S Digital Audio Serial Interface NC AVDD AGND 2 PF 1 PF AV DD Figure 1. Typical Audio Amplifier Application Circuit 2 Submit Documentation Feedback Copyright (c) 2003-2013, Texas Instruments Incorporated Product Folder Links: LM4921 LM4921 www.ti.com SNAS178E - JULY 2003 - REVISED MAY 2013 Connection Diagrams (1) 4 HP_R AVDD BYPASS NC SPI_ DATA 3 AGND HP_L NC SPI_ ENABLE SPI_ CLK 2 NC OPEN I2S_ LRCLK I2S_ DATA XTAL_ OUT MCLK/ XTAL_ IN 1 GNDD I2S_ CLK DVDD VDDX GNDX A B C D E NC - No Connection Figure 2. LM4921 20-Bump DSBGA Pin Configuration - Top View See Package Number YZR0020 Submit Documentation Feedback Copyright (c) 2003-2013, Texas Instruments Incorporated Product Folder Links: LM4921 3 LM4921 SNAS178E - JULY 2003 - REVISED MAY 2013 www.ti.com LM4921 I/O PIN DESCRIPTIONS 4 PIN # (ITL) PIN NAME PIN TYPE Input-I, Output-O, Power-P, No ConnectNC PIN DESCRIPTION B1 I2S_CLK I/O I2S Clock C2 I2S_DATA I I2S data B2 I2S_WS I/O E3 SPI_CLK I SPI clcock I2S L/R word select E4 SPI_DATA I SPI data D3 SPI_ENABLE I SPI Enable E2 MCLK/XTAL_IN I Master Clock / Xtal input D2 XTAL_OUT O Xtal output C4 BYPASS I/O Analog VDD/2 bypass capacitor connection point B4 AVDD P Analog supply A3 AGND P Analog Ground C1 DVDD P Digital Supply A1 GNDD P Digital ground D1 VDDX P XTAL Oscillator circuit supply E1 GNDX P XTAL Oscillator circuit ground B3 HP_L O HP left output A4 HP_R O HP right output A2 No Connect O Must let float C3 No Connect NC NC D4 No Connect NC NC Submit Documentation Feedback Copyright (c) 2003-2013, Texas Instruments Incorporated Product Folder Links: LM4921 LM4921 www.ti.com SNAS178E - JULY 2003 - REVISED MAY 2013 These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. Absolute Maximum Ratings (1) (2) Supply Voltage 6.0V -65C to +150C Storage Temperature Input Voltage Power Dissipation -0.3V to VDD + 0.3V (3) ESD Susceptibility Internally Limited Human body model (4) 2000V Machine model (5) 200V Junction Temperature Thermal Resistance (1) (2) (3) (4) (5) 150C JA 60C/W Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not ensure specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which ensure specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not ensured for parameters where no limit is given, however, the typical value is a good indication of device performance. All voltages are measured with respect to the GND pin, unless otherwise specified. The maximum power dissipation must be derated at elevated temperatures and is dictated by TJMAX, JA, and the ambient temperature TA. The maximum allowable power dissipation is PDMAX = (TJMAX-TA)/JA or the number given in Absolute Maximum Ratings, whichever is lower. Human body model, 100pF discharged through a 1.5k resistor. Machine Model, 220pF - 240pF discharged through all pins. Operating Ratings Temperature Range TMIN TA TMAX Supply Voltage -40C TA 85C DVDD 2.6V DVDD 5.0V AVDD 2.6V AVDD 5.5V Submit Documentation Feedback Copyright (c) 2003-2013, Texas Instruments Incorporated Product Folder Links: LM4921 5 LM4921 SNAS178E - JULY 2003 - REVISED MAY 2013 www.ti.com Electrical Characteristics DVDD = 3.0V, AVDD = 5.0V, RL = 32 (1) (2) The following specifications apply for the circuit shown in Figure 1 unless otherwise specified. Limits apply for TA = 25C. Symbol DVDD Parameter Digital Power Supply Voltage Conditions LM4921 Typical See (6) 3.0 (6) 5.0 AVDD Analog Power Supply Voltage See DIDD Digital Power Supply Quiescent Current RLoad = , fMLCK = 11.2896MHz AIDD Analog Power Supply Quiescent Current ISD (3) Limit (4) (5) Units (Limits) V V 3.5 7.5 mA (max) RLoad = , fMCLK = 0MHz 6 10 mA (max) Total Shutdown Power Supply Current SHUTDOWN SPI bits 1 & 2 set to logic 0, SPI, MCLK and I2S inputs at GND 1 5 uA(max) ISB Standby Current Analog and Digital together All clocks off 25 uA VFS Full-Scale Output Voltage Gain set at max 3.5 VP-P THD+N Total Harmonic Distortion + Noise fIN = 1kHz, POUT = 12mW (Vol Control = 11111, I2S input adj to get 12mW at output) 0.03 % PO Headphone Amplifier Output Power THD = (0.5%), fOUT = 1kHz 50 40 mW (min) PSRR Power Supply Rejection Ratio AVDD CBYPASS = 2.0F VRIPPLE = 200mVP-P 217Hz 62 45 dB (min) SNR Signal-to-Noise Ratio fIN = 1kHz sinewave at -60dBFS, A-weighted-fCONV = 44.1kHz 82 dB DR Dynamic Range fIN = 1kHz sinewave at -60dBFS, A-weighted 84 dB ACH-CH Channel-to-Channel Gain Mismatch fIN = 1kHz 0.06 dB XTALK Channel-to-Channel Crosstalk fCONV = 44.1kHz, fIN = 1kHz sinewave at -3dBFS 72 dB Volume Control Range Minimum Attenuation Maximum Attenuation +3.0 -43.5 dB dB 1.5 dB -102 dB Volume Control Control Step Size Mute Attenuation (1) (2) (3) (4) (5) (6) 6 Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not ensure specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which ensure specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not ensured for parameters where no limit is given, however, the typical value is a good indication of device performance. All voltages are measured with respect to the GND pin, unless otherwise specified. Typicals are measured at 25C and represent the parametric norm. Limits are specified to AOQL (Average Outgoing Quality Level). Datasheet min/max specification limits are specified by design, test, or statistical analysis. Best operation is achieved by maintaining 3.0V AVDD 5.0V and 3.0V DVDD 5.0V. Submit Documentation Feedback Copyright (c) 2003-2013, Texas Instruments Incorporated Product Folder Links: LM4921 LM4921 www.ti.com SNAS178E - JULY 2003 - REVISED MAY 2013 Electrical Characteristics DVDD = 3.0V, AVDD = 3.0V, RL = 32 (1) (2) The following specifications apply for the circuit shown in Figure 1 unless otherwise specified. Limits apply for TA = 25C. Symbol DVDD Parameter Digital Power Supply Voltage Conditions LM4921 Typical See (6) 3.0 (6) 3.0 AVDD Analog Power Supply Voltage See DIDD Digital Power Supply Quiescent Current RLoad = , fMLCK = 11.2896MHz AIDD Analog Power Supply Quiescent Current ISD (3) Limit (4) (5) Units (Limits) V V 3.5 7.5 mA (max) RLoad = , fMCLK = 0MHz 5 9.0 mA (max) Total Shutdown Power Supply Current SHUTDOWN SPI bits 1 & 2 set to logic 0, SPI, MCLK and I2S inputs at GND 1 uA(max) ISB Standby Current Analog and Digital together All clocks off 15 uA VFS Full-Scale Output Voltage Gain set at max 2.6 VP-P THD+N Total Harmonic Distortion + Noise fIN = 1kHz, POUT = 12mW (Vol Cont = 11011, I2S input adj to get 12mW at output) 0.05 % PO Headphone Amplifier Output Power THD = (0.5%), fOUT = 1kHz 26 mW (min) PSRR Power Supply Rejection Ratio AVDD CBYPASS = 2.0F VRIPPLE = 200mVP-P 217Hz 52 dB (min) SNR Signal-to-Noise Ratio fIN = 1kHz sinewave at -60dBFS, A-weighted-fCONV = 44.1kHz 79 dB DR Dynamic Range fIN = 1kHz sinewave at -60dBFS, A-weighted 81 dB ACH-CH Channel-to-Channel Gain Mismatch fIN = 1kHz 0.06 dB XTALK Channel-to-Channel Crosstalk fCONV = 44.1kHz, fIN = 1kHz sinewave at -3dBFS 72 dB Volume Control Range Minimum Attenuation Maximum Attenuation 0 -43.5 dB dB 1.5 dB -100 dB Volume Control Control Step Size Mute Attenuation (1) (2) (3) (4) (5) (6) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not ensure specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which ensure specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not ensured for parameters where no limit is given, however, the typical value is a good indication of device performance. All voltages are measured with respect to the GND pin, unless otherwise specified. Typicals are measured at 25C and represent the parametric norm. Limits are specified to AOQL (Average Outgoing Quality Level). Datasheet min/max specification limits are specified by design, test, or statistical analysis. Best operation is achieved by maintaining 3.0V AVDD 5.0V and 3.0V DVDD 5.0V. Submit Documentation Feedback Copyright (c) 2003-2013, Texas Instruments Incorporated Product Folder Links: LM4921 7 LM4921 SNAS178E - JULY 2003 - REVISED MAY 2013 www.ti.com Electrical Characteristics-Digital Inputs DVDD = 3.0V (1) (2) The following specifications apply for the circuit shown in Figure 1 unless otherwise specified. Limits apply for TA = 25C. Symbol Parameter Conditions Resolution LM4921 Typical (3) Limit (4) (5) Units (Limits) 16 Bits 11.2896 (256FS) MHz I2S Audio Data Interface Format Standard, I2S, Left Justified fMCLK Master Clock Frequency fCONV Sampling Clock Frequency Range 48 kHz VIL Digital Input: Logic Low Voltage Level 0.3 X DVDD V (max) VIH Digital Input: Logic High Voltage Level 0.7 X DVDD V (min) tES SPI_ENB Setup Time 20 ns (min) tEH SPI_ENB Hold Time 20 ns (min) tEL SPI_ENB Low Time 30 ns (min) tDS SPI_Data Setup Time 20 ns (min) tDH SPI_Data Hold Time 20 ns (min) tCS SPI_CLK Setup Time 20 ns (min) tCH SPI_CLK High Pulse Width 100 ns (min) tCL SPI_CLK Low Pulse Width 100 ns (min) fCLK SPI_CLK Frequency 5 MHz (max) tCLKI2S I2S_CLK Period 50 ns (min) tHII2S I2S_CLK High Pulse Width 20 ns (min) 20 ns (min) 44.1 2 tLOI2S I S_CLK Low Pulse Width I2S_LRCLK Duty Cycle 50 % tSLRCLK I2S_LRCLK to I2S_CLK Setup Time 20 ns (min) tHLRCLK I2S_LRCLK to I2S_CLK Hold Time 20 ns (min) tSDI S I2S_Data to I2S_CLK Setup Time 20 ns (min) tHDI2S I2S_Data to I2S_CLK Hold Time 20 ns (min) 2 (1) (2) (3) (4) (5) 8 Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not ensure specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which ensure specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not ensured for parameters where no limit is given, however, the typical value is a good indication of device performance. All voltages are measured with respect to the GND pin, unless otherwise specified. Typicals are measured at 25C and represent the parametric norm. Limits are specified to AOQL (Average Outgoing Quality Level). Datasheet min/max specification limits are specified by design, test, or statistical analysis. Submit Documentation Feedback Copyright (c) 2003-2013, Texas Instruments Incorporated Product Folder Links: LM4921 LM4921 www.ti.com SNAS178E - JULY 2003 - REVISED MAY 2013 Typical Performance Characteristics THD+N vs Output Power THD+N vs Output Power 10 TOTAL HARMONIC DISTORTION (%) TOTAL HARMONIC DISTORTION (%) 10 1.0 .1 .01 1m 5m 10m 20m 1.0 .1 .01 1m 50m 100m 5m POWER (W) 1. Analog VDD = 5V, Digital VDD = 3V RL = 32, 44.1 kHz Sample Rate R & L Channels, Vol = 3dB, Frequency in = 1kHz Figure 3. 50m 100m Analog VDD = 3V, Digital VDD = 3V RL = 32, 44.1 kHz Sample Rate R & L Channels Shown Vol = 3dB, Frequency in = 1kHz Figure 4. THD+N vs Output Power THD+N vs Frequency 10 TOTAL HARMONIC DISTORTION (%) 10 TOTAL HARMONIC DISTORTION (%) 10m 20m POWER (W) 1.0 .1 .01 1m 1.0 .1 .01 5m 10m 20m 50m 100m 20 100 POWER (W) 1k 10k 20k FREQUENCY (Hz) Analog VDD = 2.6V, Digital VDD = 2.6V RL = 32, 4.1 kHz Sample Rate R & L Channels Shown, Vol = 3dB, Frequency in = 1kHz Figure 5. Analog VDD = 5V, Digital VDD = 3V RL = 32, Power Level = 50mW, R & L Channels Shown , 44.1kHz Sample Rate Figure 6. THD+N vs Frequency THD+N vs Frequency 10 TOTAL HARMONIC DISTORTION (%) TOTAL HARMONIC DISTORTION (%) 10 1.0 .1 1.0 .1 .01 .01 20 20 100 1k 10k 20k 100 1k 10k 20k FREQUENCY (Hz) FREQUENCY (Hz) Analog VDD = 3V, Digital VDD = 3V RL = 32, Power Level = 12mW R & L Channels Shown, 44.1kHz Sample Rate Figure 7. Analog VDD = 2.6V, Digital VDD = 2.6V RL = 32, Power Level = 12mW R & L Channels Shown, 44.1kHz Sample Rate Figure 8. Submit Documentation Feedback Copyright (c) 2003-2013, Texas Instruments Incorporated Product Folder Links: LM4921 9 LM4921 SNAS178E - JULY 2003 - REVISED MAY 2013 www.ti.com Typical Performance Characteristics (continued) Crosstalk Frequency Response 0 10 -10 0 -30 AMPLITUDE (dB) CROSSTALK (dB) -20 -40 -50 -60 -70 -80 -20 -40 -60 -80 -90 -100 20 -100 100 1k 20 10k 20k 100 1k Analog VDD = 5V, Digital VDD = 3V RL = 32, Vol = 0dB 44.1kHz Sample Rate, 0dB FFS Figure 10. Analog VDD = 3V, Digital VDD = 3V RL = 32, Vol = 3dB 44.1kHz Sample Rate, -3dB FFS Figure 9. Linearity ANALOG OUTPUT SIGNAL AMPLITUDE (dB) ANALOG OUTPUT SIGNAL AMPLITUDE (dB) Linearity 10 0 -20 -40 -60 -80 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 0 10 0 -20 -40 -60 -80 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 DIGITAL INPUT SIGNAL AMPLITUDE (dB) Analog VDD = 3V, Digital VDD = 3V RL = 32, 44.1kHz Sample Rate Figure 12. Noise Floor Noise Floor 0 0 -20 -20 -40 -40 AMPLITUDE (dB) AMPLITUDE (dB) 0 DIGITAL INPUT SIGNAL AMPLITUDE (Db) Analog VDD = 5V, Digital VDD = 3V RL = 32, 44.1kHz Sample Rate Figure 11. -60 -80 -100 -60 -80 -100 -130 -130 20 100 1k 10k 20k 20 FREQUENCY (Hz) Analog VDD = 5V, Digital VDD = 3V RL = 32, Vol = 3dB 44.1kHz Sample Rate Figure 13. 10 10k 20k FREQUENCY (Hz) FREQUENCY (Hz) 100 1k 10k 20k FREQUENCY (Hz) Analog VDD = 3V, Digital VDD = 3V RL = 32, Vol = 0dB 44.1kHz Sample Rate Figure 14. Submit Documentation Feedback Copyright (c) 2003-2013, Texas Instruments Incorporated Product Folder Links: LM4921 LM4921 www.ti.com SNAS178E - JULY 2003 - REVISED MAY 2013 Typical Performance Characteristics (continued) PSRR vs Frequency 0 0 -20 -20 AMPLITUDE (dB) AMPLITUDE (dB) PSRR vs Frequency -40 -60 -80 -40 -60 -80 -100 -100 20 100 1k 10k 20k 20 FREQUENCY (HZ) 100 1k 10k 20k FREQUENCY (Hz) Analog VDD = 5V, Digital VDD = 3V RL = 32, Vol = 3dB 44.1kHz Sample Rate Figure 15. Analog VDD = 3V, Digital VDD = 3V RL = 32, Vol = 0dB 44.1kHz Sample Rate Figure 16. FFT @ 1kHz -60dB FFT @ 1kHz 0dB 0 0 -40 AMPLITUDE (dB) AMPLITUDE (dB) -20 -60 -80 -100 -40 -70 -100 -130 -130 20 100 1k 10k 20k 20 FREQUENCY (Hz) 100 1k 10k 20k FREQUENCY (Hz) Analog VDD = 5V, Digital VDD = 3V RL = 32, Vol = 3dB 44.1kHz Sample Rate Figure 17. Analog VDD = 5V, Digital VDD = 3V RL = 32, Vol = 3dB 44.1 kHz Sample Rate Figure 18. FFT @ 1kHz -60dB FFT @ 1kHz 0dB 0 0 -40 AMPLITUDE (dB) AMPLITUDE (dB) -20 -60 -80 -100 -40 -70 -100 -130 -130 20 100 1k 10k 20k 20 FREQUENCY (Hz) Analog VDD = 3V, Digital VDD = 3V RL = 32, Vol = 0dB 44.1kHz Sample Rate Figure 19. 100 1k 10k 20k FREQUENCY (Hz) Analog VDD = 3V, Digital VDD = 3V RL = 32, Vol = 0dB 44.1kHz Sample Rate Figure 20. Submit Documentation Feedback Copyright (c) 2003-2013, Texas Instruments Incorporated Product Folder Links: LM4921 11 LM4921 SNAS178E - JULY 2003 - REVISED MAY 2013 www.ti.com APPLICATION INFORMATION SPI OPERATIONAL DESCRIPTION The serial data bits are organized into a field which contains 16 bits of data defined by Table 1. Bits 1 & 2 determine the output mode of the LM4921 as shown in Table 2. Bits 7 through 11 determine the volume level setting as illustrated by Table 3. Bit 12 sets the Bypass capacitor charging time. Table 1. Bit Allocation BIT # Default Val Function Description 0 (LSB) 0 RESET_B RESET_B = 0, Resets the DAC Must be high for the part to run. 1 0 2 0 MODE CONTROL See Table 2 3 0 MASTER/SLAVE 0 = SLAVE, 1 = MASTER 4 0 RESOLUTION 0 = 16 bit, 1 = 32 bit 5 0 RESERVED Should always be set to '1' 6 0 ZERO CROSSING SET 0 = ZXD ENABLE, 1 = ZXD DISABLE 7 0 VOLUME CONTROL See Table 3 8 0 9 0 10 0 11 0 12 0 BYP CHARGE RATE 0 = 1X, 1 = 2X 13 0 RESERVED 14 0 RESERVED 15 (MSB) 0 RESERVED Should always be set to '0' MODE CONTROL Sets the modes as outlined in Table 2. Table 2. Output Mode Selection (Bits 1 & 2 above) Output Mode # BIT 2 BIT 1 0 0 0 MODE SD 1 0 1 STANDBY 2 1 0 MUTE 3 1 1 ACTIVE Shutdown turns off the part completely for maximum power savings. The Standby mode turns off the clock but still consumes more power than the shutdown mode. However, coming out of standby mode allows the part to turn back on faster than from shutdown. In Mute mode the clocks remain on which uses more power but allows faster recovery and the ability to supply clock signals to other devices which is important when the part is used in master mode. Active mode turns the part on for normal operation. MASTER/SLAVE SELECT Allows the part to act as a master and supply the clock for the rest of the system or be a slave to the system clock. RESOLUTION SET Sets the resolution to be either 16 or 32 bits of stereo audio information. For most applications this will be set at 16 bits. 12 Submit Documentation Feedback Copyright (c) 2003-2013, Texas Instruments Incorporated Product Folder Links: LM4921 LM4921 www.ti.com SNAS178E - JULY 2003 - REVISED MAY 2013 ZERO CROSSING DETECT SET This pin turns on the zero crossing detection circuit. With this circuit enabled the part will not allow a volume step change, or shutdown mode, or standby mode to occur until the audio input signal passes through zero. This pin should be set to on for most applications. VOLUME CONTROL The internal Stereo Volume Control is set by changing bits 7 through 11 in the SPI interface, as shown in Table 3 below. The zero dB setting is for 3V VDD operation and the +3dB is for 5V VDD. Table 3. Volume Control Settings Gain (dB) Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 -43.5 0 0 0 0 0 -42.0 0 0 0 0 1 -40.5 0 0 0 1 0 -39.0 0 0 0 1 1 -37.5 0 0 1 0 0 -36.0 0 0 1 0 1 -34.5 0 0 1 1 0 -33.0 0 0 1 1 1 -31.5 0 1 0 0 0 -30.0 0 1 0 0 1 -28.5 0 1 0 1 0 -27.0 0 1 0 1 1 -25.5 0 1 1 0 0 -24.0 0 1 1 0 1 -22.5 0 1 1 1 0 -21.0 0 1 1 1 1 -19.5 1 0 0 0 0 -18.0 1 0 0 0 1 -16.5 1 0 0 1 0 -15.0 1 0 0 1 1 -13.5 1 0 1 0 0 -12.0 1 0 1 0 1 -10.5 1 0 1 1 0 -9.0 1 0 1 1 1 -7.5 1 1 0 0 0 -6.0 1 1 0 0 1 -4.5 1 1 0 1 0 -3.0 1 1 0 1 1 -1.5 1 1 1 0 0 0.0 1 1 1 0 1 1.5 1 1 1 1 0 3.0 1 1 1 1 1 HP_L & HP_R Submit Documentation Feedback Copyright (c) 2003-2013, Texas Instruments Incorporated Product Folder Links: LM4921 13 LM4921 SNAS178E - JULY 2003 - REVISED MAY 2013 www.ti.com BYPASS CHARGE RATE BIT 12 This control pin allows the user to change the Bypass Capacitor's charge rate by a factor of two. Setting this bit at zero will set the circuit to it's normal 1x rate. Setting the bit to High will double the charge rate and allow the part to turn on faster with a slight degradation in turn on click/pop noise. BITS 5, 13, 14, and 15 Bits 13, 14, and 15 are all reserve bits and must be set to low/zero/ground. Bit 5 must be set High. SPI CONTROL INTERFACE BUS (J1) SPI DATA: This is the serial data pin. SPI CLK: This is the clock input pin. SPI ENABLE: This is the SPI enable pin. SPI TIMING DIAGRAM SPI OPERATIONAL REQUIREMENTS 1. The maximum clock rate is 5MHz for the CLK pin. 2. CLK must remain logic-high for at least 100ns (tCH ) after the rising edge of CLK, and CLK must remain logiclow for at least 100ns (tCL ) after the falling edge of CLK. 3. Data bits are written to the DATA pin with the least significant bit (LSB) first. 4. The serial data bits are sampled at the rising edge of CLK. Any transition on DATA must occur at least 20ns (tDS) before the rising edge of CLK. Also, any transition on DATA must occur at least 20ns (tDH) after the rising edge of CLK and stabilize before the next rising edge of CLK. 5. ENABLE should be logic-high only during serial data transmission. 6. ENABLE must be logic-high at least 20ns (tES ) before the first rising edge of CLK, and ENABLE has to remain logic-high at least 20ns (tEH ) after the sixteenth rising edge of CLK. 7. If ENABLE remains logic-low for more than 10ns before all 16 bits are transmitted then the data latch will be aborted. 8. If ENABLE is logic-high for more than 16 CLK pulses then only the first 16 data bits will be latched and activated at rising edge of sixteenth CLK. 9. ENABLE must remain logic-low for at least 30ns (tEL ). 10. Coincidental rising or falling edges of CLK and ENABLE are not allowed. If CLK is to be held logic-high after the data transmission, the falling edge of CLK must occur at least 20ns (tCS ) before ENABLE transitions to logichigh for the next set of data. 14 Submit Documentation Feedback Copyright (c) 2003-2013, Texas Instruments Incorporated Product Folder Links: LM4921 LM4921 www.ti.com SNAS178E - JULY 2003 - REVISED MAY 2013 I2S INTERFACE BUS (J2 - See Figure 21 ) The I2S standard provides a uni-directional serial interface designed specifically for digital audio. For the LM4921, the interface provides access to a 48kHz, 16 bit full-range stereo audio DAC. This interface uses a three wire system of clock (I2S_CLK), data (I2S_DATA), and word select (I2S_WS, sometimes called Right/Left Select). A bit clock (I2S_CLK) at 32 or 64 times the sample frequency is established by the I2S system master and the word select (I2S_WS) line is driven at a frequency equal to the sampling rate of the audio data, in this case 48kHz. The word line is registered to change on the positive edge of the bit clock. The serial data (I2S_DATA) is sent MSB first, again registers on the positive edge of the bit clock, delayed by 1 bit clock cycle relative to the changing of the word line (typical I2S format). MCLK/XTAL_IN (S1 MCLK SEL - See Figure 21) This is the input for an external Master Clock. The jumper at S1 must be removed (disconnecting the onboard crystal from the circuit) when using an external Master Clock. STEREO HEADPHONE OUTPUT JACK (J3 - See Figure 21) This is the stereo headphone output. Each channel is single-ended, with 100uF DC output blocking capacitors mounted on the demo board (C6 and C7). These capacitors are necessary to block the 1/2 VDD DC bias and prevent it from flowing through the headphone speakers (DC current will destroy most audio speakers) while allowing the audio ac signal to pass through. The jack features a typical stereo headphone pinout. Submit Documentation Feedback Copyright (c) 2003-2013, Texas Instruments Incorporated Product Folder Links: LM4921 15 LM4921 SNAS178E - JULY 2003 - REVISED MAY 2013 www.ti.com LM4921ITL DEMO BOARD OPERATION The LM4921ITL demo board is a complete evaluation platform (Parallel Port SPI Interface Card and control software available), designed to give easy access to the control pins of the part and comprise all the necessary external passive components. There are separate analog and digital supply connectors, SPI interface bus (J1) for the control lines, I2S interface bus (J2) for full-range digital audio, stereo headphone output (J3), and an external MCLK input (P1) for use in place of the crystal on the demoboard. Red Banana Plug C3 1 PF VDDD E 4 D3 E 3 NC KEY SPI_DAT A SPI_ENABL E SPI_CL K HP R B 3 C6 A 4 C7 C4 BYPAS S HEADPHONE JACK J3 100 PF 100 PF Right Out Test Jack Ground Black Banana Plug I2S_DAT A I2S_CL KI2S_WS (LRCLK) GND X GND D C2 B 1 B 2 10 9 8 7 6 5 4 3 2 1 C8 2.2 PF Analo g Ground Black Banana Plug (1) HP L U1 LM4921ITL J2 I2S Interface C5 1 PF N C N C N C A 2 D4 C3 N C N C N C Right Out Test RedJack Banana Plug E 1 A 1 6 5 4 3 2 1 GND A J1 MCLK/XTAL IN XTAL OUT VDDX D1 C1 CA P E 2 D2 1 2 C4 1 PF Left Out Test Jack Ground Black Banana Plug C2 VDDD CA P Digital VDD VDDD Red Banana Plug B 4 CRYSTA L C1 MCLK IN P 1 SPI Interface 1M Y 1 VDDA VDDA MCL K SE L Analog VDD A 3 S 1 R1 Left Out Test RedJack Banana Plug Digita l Ground Black Banana Plug Parallel Port SPI Interface Card and control software available. Figure 21. LM4921ITL Demo Board Schematic 16 Submit Documentation Feedback Copyright (c) 2003-2013, Texas Instruments Incorporated Product Folder Links: LM4921 LM4921 www.ti.com SNAS178E - JULY 2003 - REVISED MAY 2013 DEMO BOARD BILL OF MATERIALS Texas Instruments Bill of Material Analog Audio LM4921ITL20 Eval Board Assembly Part Number: 980011973-100 Revision A Item Part Number Part Description Qty 1 551011973-001 LM4921 Eval Board PCB etch 001 1 Ref Designator 2 LM4921 ITL20 DSBGA 20 Bumps 1 U1 3 Cer Cap 22pF 50V 10%, size 1206 2 C1, C2 4 Cer Cap 0.1pF 50V 10%, size 1206 1 C4 5 Tant Cap 1F 16V 10%, 3216 3 C3, C5, C8 6 Tant Cap 220F 16V 10%, 7243 2 C6, C7 7 1 meg ohm 1 R1 8 Crystal 11.2896MHz 1 Y1 9 Phone Jack 3.5mm Stereo 1 J3 10 Jumper Header 1X2 2 P1, S1 11 Jumper Header 1X3 2 J1 12 Jumper Header 1X5 2 J2 13 PCB Banana Jack, Black-Mouser 164-6218 4 A GND, D GND, GND (2) 14 PCB Banana Jack, Red-Mouser 164-6219 4 A VDD, D VDD, HP L, HP R Submit Documentation Feedback Copyright (c) 2003-2013, Texas Instruments Incorporated Product Folder Links: LM4921 17 LM4921 SNAS178E - JULY 2003 - REVISED MAY 2013 www.ti.com DEMO BOARD ARTWORKS Figure 22. Silkscreen Layer Figure 23. Top Layer 18 Submit Documentation Feedback Copyright (c) 2003-2013, Texas Instruments Incorporated Product Folder Links: LM4921 LM4921 www.ti.com SNAS178E - JULY 2003 - REVISED MAY 2013 Figure 24. Mid Layer 1 Figure 25. Mid Layer 2 Submit Documentation Feedback Copyright (c) 2003-2013, Texas Instruments Incorporated Product Folder Links: LM4921 19 LM4921 SNAS178E - JULY 2003 - REVISED MAY 2013 www.ti.com Figure 26. Bottom Layer 20 Submit Documentation Feedback Copyright (c) 2003-2013, Texas Instruments Incorporated Product Folder Links: LM4921 LM4921 www.ti.com SNAS178E - JULY 2003 - REVISED MAY 2013 REVISION HISTORY Changes from Revision D (May 2013) to Revision E * Page Changed layout of National Data Sheet to TI format .......................................................................................................... 20 Submit Documentation Feedback Copyright (c) 2003-2013, Texas Instruments Incorporated Product Folder Links: LM4921 21 PACKAGE OPTION ADDENDUM www.ti.com 2-May-2013 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish (2) MSL Peak Temp Op Temp (C) Top-Side Markings (3) (4) LM4921ITL/NOPB ACTIVE DSBGA YZR 20 250 Green (RoHS & no Sb/Br) SNAGCU Level-1-260C-UNLIM -40 to 85 G B9 LM4921ITLX/NOPB ACTIVE DSBGA YZR 20 3000 Green (RoHS & no Sb/Br) SNAGCU Level-1-260C-UNLIM -40 to 85 G B9 (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) Multiple Top-Side Markings will be inside parentheses. Only one Top-Side Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Top-Side Marking for that device. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 Samples PACKAGE MATERIALS INFORMATION www.ti.com 8-May-2013 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) LM4921ITL/NOPB DSBGA YZR 20 250 178.0 8.4 LM4921ITLX/NOPB DSBGA YZR 20 3000 178.0 8.4 Pack Materials-Page 1 B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 2.34 2.85 0.76 4.0 8.0 Q1 2.34 2.85 0.76 4.0 8.0 Q1 PACKAGE MATERIALS INFORMATION www.ti.com 8-May-2013 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LM4921ITL/NOPB DSBGA YZR LM4921ITLX/NOPB DSBGA YZR 20 250 210.0 185.0 35.0 20 3000 210.0 185.0 35.0 Pack Materials-Page 2 MECHANICAL DATA YZR0020xxx 0.6000.075 D E TLA20XXX (Rev D) D: Max = 2.772 mm, Min =2.711 mm E: Max = 2.238 mm, Min =2.177 mm 4215053/A NOTES: A. All linear dimensions are in millimeters. Dimensioning and tolerancing per ASME Y14.5M-1994. B. This drawing is subject to change without notice. www.ti.com 12/12 IMPORTANT NOTICE Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. TI's published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integrated circuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products and services. Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduced documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyers and others who are developing systems that incorporate TI products (collectively, "Designers") understand and agree that Designers remain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers have full and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI products used in or for Designers' applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, with respect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerous consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and take appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer will thoroughly test such applications and the functionality of such TI products as used in such applications. TI's provision of technical, application or other design advice, quality characterization, reliability data or other services or information, including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, "TI Resources") are intended to assist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in any way, Designer (individually or, if Designer is acting on behalf of a company, Designer's company) agrees to use any particular TI Resource solely for this purpose and subject to the terms of this Notice. TI's provision of TI Resources does not expand or otherwise alter TI's applicable published warranties or warranty disclaimers for TI products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections, enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specifically described in the published documentation for a particular TI Resource. Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. TI RESOURCES ARE PROVIDED "AS IS" AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM, INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL, DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949 and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements. Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, such products are intended to help enable customers to design and create their own applications that meet applicable functional safety standards and requirements. Using products in an application does not by itself establish any safety features in the application. Designers must ensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products in life-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use. Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., life support, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, all medical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S. TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product). Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applications and that proper product selection is at Designers' own risk. Designers are solely responsible for compliance with all legal and regulatory requirements in connection with such selection. Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer's noncompliance with the terms and provisions of this Notice. Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2017, Texas Instruments Incorporated Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Texas Instruments: LM4921ITL/NOPB LM4921ITLEVAL LM4921ITLX/NOPB