SCOPE: 8-CHANNEL/DUAL 4-CHANNEL CMOS, ANALOG SWITCHES Device Type 01 02 Generic Number DG408A(x)/883B DG409A(x)/883B SMD Number 5962-9204201 5962-9204202 Case Outline(s). The case outlines shall be designated in Mil-Std-1835 and as follows: Outline Letter Maxim SMD K E L X Z 2 Mil-Std-1835 GDIP1-T16 or CDIP2-T16 CDFP3-F16 CQCC1-N20 Case Outline Package Code 16 LEAD CERDIP 16 LEAD FLATPACK 20-Pin Ceramic LCC J16 F16 L20 Absolute Maximum Ratings Voltage Referenced to VV+ to V- .............................................................................................................................. 44V V- to GND ......................................................................................................................... 25V Digital Inputs Overvoltage Range 1/ ..................................................... .(V - -2V) to (V+ +2V) or 20mA whichever occurs first. Continuous Current, Any terminal except S or D ........................................................... 30mA Continuous Current, S or D ............................................................................................. 20mA Current, S or D (Pulsed at 1ms, 10% duty cycle max) .................................................... 40mA Lead Temperature (soldering, 10 seconds) ........................................................................ +300C Storage Temperature ........................................................................................... -65C to +150C Continuous Power Dissipation .................................................................................. TA=+70C 16 lead CERDIP(derate 10.0mW/C above +70C) ...................................................... 800mW 16 lead FLATPACK(derate 6.1mW/C above +70C) ................................................... 485mW 20 lead LCC(derate 9.1mW/C above +70C) ................................................................ 727mW Junction Temperature TJ .............................................................................................. +150C Thermal Resistance, Junction to Case, JC: Case Outline 16 lead CERDIP.......................................................................... 50C/W Case Outline 16 lead FLATPACK .................................................................. 65C/W Case Outline 20 lead LCC .............................................................................. 55C/W Thermal Resistance, Junction to Ambient, JA: Case Outline 16 lead CERDIP....................................................................... 100C/W Case Outline 16 lead FLATPACK ................................................................ 165C/W Case Outline 20 lead LCC ............................................................................. 110C/W Recommended Operating Conditions Ambient Operating Range (TA) .................................................................... -55C to +125C Positive Supply Voltage (V+) ........................................................................................... +15V Negative Supply Voltage (V-) ........................................................................................... -15V 1/ Signals on S, D or IN exceeding V+ or V- are clamped by internal diodes. Limit forward current to maximum current ratings. Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ---------------------------- Electrical Characteristics of DG408A/409A/883B for SMD 5962-92042 19-0368 Page 2 of Rev. B 6 TABLE 1. ELECTRICAL TESTS: TEST SWITCH Analog-Signal Range Drain-Source ON Resistance rDS(ON) Matching Between Channels Symbol CONDITIONS -55 C <=TA<= +125C V+=+15V, V-=-15V, GND=0V VAH=2.4V, VAL=0.8V, VEN=2.4V Unless otherwise specified VANALOG NOTE 2 rDS(ON) IS=-10mA, VD=10V rDS IS=-10mA, VD=10V, NOTE 3 Group A Subgroup Device type 1,2,3 All 1,3 2 1 All Limits Min -15 All Limits Max Units 15 V 100 125 15 (ON) Source-OFF Leakage Current IS(OFF) VS=10V, VD=10V, VEN=0V 1 2 All -0.5 -50 0.5 50 nA Drain-OFF Leakage Current ID(OFF) VS=10V, VD=10V, VEN=0V All 01 02 ID(ON)+ IS(ON) VS=10V, VD=10V, sequence each switch on All 01 02 -1.0 -100 -50 -1.0 -100 -50 1.0 100 50 1.0 100 50 nA Drain-ON Leakage Current 1 2 2 1 2 2 VA= 2.4V, 15V 1,2,3 All -10 10 A IAL VA=0V, VEN= 0V, 2.4V 1,2,3 All -10 10 A +ISBY VA=0V, VEN= 0V 1,2,3 All 75 A -ISBY VA=0V, VEN= 0V 1,2,3 All I+ VA=0V, VEN= 2.4V All I- VA=0V, VEN= 2.4V 1,3 2 1,2,3 All -0.5 tTRANS tOPEN Figure 2 Figure 4 9,10,11 9 All All 10 tON(EN) Figure 3 All tOFF(EN) Figure 3 9,11 10 9,10,11 INPUT Input Current/Voltage High Input Current/Voltage Low Standby Positive Supply Current Standby Negative Supply Current SUPPLY Positive Supply Current Negative Supply Current DYNAMIC Transition Time Break Before Make Time Enable Turn-On Time Enable Turn-Off Time nA IAH A -75 0.5 2.0 All mA 250 ns ns 150 225 150 ns NOTE 2: Guaranteed by design. NOTE 3: rDS(ON)= rDS(ON)max-rDS(ON)min FIGURE 2: TRANSITION TIME TEST CIRCUIT: See Commercial Data Sheet FIGURE 3: ENABLE SWITCHING TIME: See Commercial Data Sheet FIGURE 4: BREAK-BEFORE-MAKE INTERVAL: See Commercial Data Sheet ---------------------------- Electrical Characteristics of DG408A/409A/883B for SMD 5962-92042 19-0368 Page 3 of mA Rev. B 6 ns ORDERING INFORMATION: SMD NUMBER 5962-9204201MEA 5962-9204201MXC 5962-9204201M2C 5962-9204202MEA 5962-9204202MXC 5962-9204202M2C DG408AK/883B DG408AL/883B DG408AZ/883B DG409AK/883B DG409AL/883B DG409AZ/883B TRUTH TABLES: A2 A1 A0 X L L L L H H H H X L L H H L L H H X L L H H X L H L H L H L H X L H L H ---------------------------- EN CIRCUIT FUNCTION 8-channel analog multiplexer 8-channel analog multiplexer 8-channel analog multiplexer Dual 4-channel analog multiplexer Dual 4-channel analog multiplexer Dual 4-channel analog multiplexer L H H H H H H H H DG408A ON SWITCH None 1 2 3 4 5 6 7 8 X H H H H DG409A ON SWITCH None 1 2 3 4 Terminal Number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 PKG CODE 16 CERDIP 16 FLATPACK 20 LCC 16 CERDIP 16 FLATPACK 20 LCC TERMINAL CONNECTION DG408 DG408 DG409 J16 & F16 A0 EN VS1 S2 S3 S4 D S8 S7 S6 S5 V+ GND A2 A1 Electrical Characteristics of DG408A/409A/883B for SMD 5962-92042 LCC20 NC A0 EN VS1 NC S2 S3 S4 D NC S8 S7 S6 S5 NC V+ GND A2 A1 19-0368 Page 4 of J16 & F16 A0 EN VS1a S2a S3a S4a Da Db S4b S3b S2b S1b V+ GND A1 Rev. B 6 DG409 LCC20 NC A0 EN VS1a NC S2a S3a S4a DA NC DB S4b S3b S2b NC S1b V+ GND A1 QUALITY ASSURANCE Sampling and inspection procedures shall be in accordance with MIL-Prf-38535, Appendix A as specified in MilStd-883. Screening shall be in accordance with Method 5004 of Mil-Std-883. Burn-in test Method 1015: 1. Test Condition, A, B, C, or D. 2. TA = +125C minimum. 3. Interim and final electrical test requirements shall be specified in Table 2. Quality conformance inspection shall be in accordance with Method 5005 of Mil-Std-883, including Groups A, B, C, and D inspection. Group A inspection: 1. Tests as specified in Table 2. 2. Selected subgroups in Table 1, Method 5005 of Mil-Std-883 shall be omitted. Group C and D inspections: a. End-point electrical parameters shall be specified in Table 1. b. Steady-state life test, Method 1005 of Mil-Std-883: 1. Test condition A, B, C, D. 2. TA = +125C, minimum. 3. Test duration, 1000 hours, except as permitted by Method 1005 of Mil-Std-883. TABLE 2. ELECTRICAL TEST REQUIREMENTS Mil-Std-883 Test Requirements Interim Electric Parameters Method 5004 Final Electrical Parameters Method 5005 Group A Test Requirements Method 5005 Group C and D End-Point Electrical Parameters Method 5005 * ** Subgroups per Method 5005, Table 1 1 1*, 2, 3, 7, 8, 9, 10, 11 1, 2, 3, 7**, 8**, 9, 10, 11 1 PDA applies to Subgroup 1 only. Subgroups 7 and 8 tests shall be sufficient to verify the truth table. ---------------------------- Electrical Characteristics of DG408A/409A/883B for SMD 5962-92042 19-0368 Page 5 of Rev. B 6