ISP1106DHTM - St-Ericsson - Product.Network

34.807IRELESS

IMPORTANT NOTICE

Dear customer,

As from August 2nd 2008, the wireless operations of NXP have moved to a new company,

ST-NXP Wireless.

As a result, the following changes are applicable to the attached document.

●Company name - Philips Semiconductors is replaced with ST-NXP Wireless.

●Copyright - the copyright notice at the bottom of each page “© Koninklijke Philips

●Web site - http://www.semiconductors.philips.com is replaced with

http://www.stnwireless.com

●Contact information - the list of sales offices previously obtained by sending an email

to sales.addresses@www.semiconductors.philips.com, is now found at

http://www.stnwireless.com under Contacts.

If you have any questions related to the document, please contact our nearest sales office.

Thank you for your cooperation and understanding.

ST-NXP Wireless

34.807IRELESS

www.stnwireless.com

ISP1105/1106

Advanced Universal Serial Bus transceivers

Rev. 08 — 19 February 2004 Product data

1. General description

The ISP1105/1106 range of Universal Serial Bus (USB) transceivers are compliant

with the

Universal Serial Bus Speciﬁcation Rev. 2.0

. They can transmit and receive

serial data at both full-speed (12 Mbit/s) and low-speed (1.5 Mbit/s) data rates. The

ISP1105/1106 range can be used as a USB device transceiver or a USB host

transceiver.

They allow USB Application Speciﬁc ICs (ASICs) and Programmable Logic Devices

(PLDs) with power supply voltages from 1.65 V to 3.6 V to interface with the physical

layer of the Universal Serial Bus. They have an integrated 5 V-to-3.3 V voltage

regulator for direct powering via the USB supply VBUS.

ISP1105 allows single-ended and differential input modes selectable by a MODE

input and it is available in HVQFN16 and HBCC16 packages. ISP1106 allows only

differential input mode and is available in both TSSOP16 and HBCC16 packages.

The ISP1105/1106 are ideal for portable electronics devices such as mobile phones,

digital still cameras, Personal Digital Assistants (PDA) and Information Appliances

(IA).

2. Features

■Complies with

Universal Serial Bus Speciﬁcation Rev. 2.0

■Can transmit and receive serial data at both full-speed (12 Mbit/s) and low-speed

(1.5 Mbit/s) data rates

■Integrated bypassable 5 V-to-3.3 V voltage regulator for powering via USB VBUS

■VBUS disconnection indication through VP and VM

■Used as a USB device transceiver or a USB host transceiver

■Stable RCV output during SE0 condition

■Two single-ended receivers with hysteresis

■Low-power operation

■Supports an I/O voltage range from 1.65 V to 3.6 V

■±12 kV ESD protection at the D+, D−, VCC(5.0) and GND pins

■Full industrial operating temperature range from −40 to +85 °C

■Available in small HBCC16, HVQFN16 (only ISP1105) and TSSOP16 (only

ISP1106) packages; HBCC16 and HVQFN16 are lead-free and halogen-free

packages.

Philips Semiconductors ISP1105/1106

Advanced USB transceivers

Product data Rev. 08 — 19 February 2004 2 of 28

3. Applications

■Portable electronic devices, such as:

◆Mobile phone

◆Digital still camera

◆Personal Digital Assistant (PDA)

◆Information Appliance (IA).

4. Ordering information

4.1 Ordering options

Table 1: Ordering information

Type number Package

Name Description Version

ISP1105BS HVQFN16 plastic thermal enhanced very thin quad ﬂat package; no leads;

16 terminals; body 3 ×3×0.85 mm SOT758-1

ISP1105W HBCC16 plastic thermal enhanced bottom chip carrier; 16 terminals;

body 3 ×3×0.65 mm SOT639-2

ISP1106DH TSSOP16 plastic thin shrink small outline package; 16 leads; body width 4.4 mm SOT403-1

ISP1106W HBCC16 plastic thermal enhanced bottom chip carrier; 16 terminals;

body 3 ×3×0.65 mm SOT639-2

Table 2: Selection guide

Product Package Description

ISP1105 HVQFN16 and HBCC16 supports both single-ended and differential input modes; see Table 5 and Table 6.

ISP1106 TSSOP16 and HBCC16 supports only the differential input mode; see Table 6.

Philips Semiconductors ISP1105/1106

Advanced USB transceivers

Product data Rev. 08 — 19 February 2004 3 of 28

5. Block diagram

(1) Connect to D− for low-speed operation.

(2) Pin function depends on device type.

(3) Only for ISP1105.

Fig 1. Block diagram (combined ISP1105 and ISP1106).

MBL301

VCC(I/O) VCC(5.0)

VOLTAGE

REGULATOR

3.3 V

1.5 kΩ

(1)

33 Ω

(1%)

33 Ω

(1%)

LEVEL

SHIFTER

ISP1105

ISP1106

SOFTCON

SPEED

Vreg(3.3)

GND

Vpu(3.3)

D+

D−

VMO/FSE0

(2)

VPO/VO

(2)

MODE

(3)

SUSPND

RCV

Philips Semiconductors ISP1105/1106

Advanced USB transceivers

Product data Rev. 08 — 19 February 2004 4 of 28

6. Pinning information

6.1 Pinning

Fig 2. Pin conﬁguration ISP1105BS (HVQFN). Fig 3. Pin conﬁguration ISP1105W (HBCC16).

004aaa314

ISP1105BS

D−

D+

MODE

SUSPND

VPO/VO

VMO/FSE0

GND

(exposed diepad)

VCC(I/O)

567

SPEED

112

Bottom view

RCV

Vpu(3.3)

SOFTCON

VCC(5.0)

Vreg(3.3)

MBL303

Bottom view

ISP1105W

SOFTCON

Vpu(3.3)

RCV

D+

D−

SPEED

VCC(I/O)

VPO/VO

SUSPND

MODE

VCC(5.0)

Vreg(3.3)

VMO/FSE0

141516

876

GND

(exposed diepad)

Fig 4. Pin conﬁguration ISP1106DH (TSSOP16). Fig 5. Pin conﬁguration ISP1106W (HBCC16).

ISP1106DH

MBL302

Vpu(3.3)

SOFTCON

RCV

SUSPND

GND VCC(I/O)

SPEED

D−

D+

VPO

VMO

Vreg(3.3)

VCC(5.0)

MBL304

Bottom view

ISP1106W

SOFTCON

Vpu(3.3)

RCV

D+

D−

SPEED

VCC(I/O)

VPO

SUSPND

GND

VCC(5.0)

Vreg(3.3)

VMO

141516

876

Philips Semiconductors ISP1105/1106

Advanced USB transceivers

Product data Rev. 08 — 19 February 2004 5 of 28

6.2 Pin description

Table 3: Pin description

Symbol[1] Pin Type Description

ISP1105 ISP1106

BS W DH W

OE 1131I output enable input (CMOS level with respect to VCC(I/O), active LOW);

enables the transceiver to transmit data on the USB bus

input pad; push pull; CMOS

RCV 2242O differential data receiver output (CMOS level with respect to VCC(I/O));

driven LOW when input SUSPND is HIGH; the output state of RCV is

preserved and stable during an SE0 condition

output pad; push pull; 4 mA output drive; CMOS

VP 3353O single-ended D+ receiver output (CMOS level with respect to VCC(I/O)); for

external detection of single-ended zero (SE0), error conditions, speed of

connected device; driven HIGH when no supply voltage is connected to

VCC(5.0) and Vreg(3.3)

output pad; push pull; 4 mA output drive; CMOS

VM 4464O single-ended D− receiver output (CMOS level with respect to VCC(I/O)); for

external detection of single-ended zero (SE0), error conditions, speed of

connected device; driven HIGH when no supply voltage is connected to

VCC(5.0) and Vreg(3.3)

output pad; push pull; 4 mA output drive; CMOS

SUSPND 5575I suspend input (CMOS level with respect to VCC(I/O)); a HIGH level enables

low-power state while the USB bus is inactive and drives output RCV to a

LOW level

input pad; push pull; CMOS

MODE 6 6 - - I mode input (CMOS level with respect to VCC(I/O)); a HIGH level enables the

differential input mode (VPO, VMO) whereas a LOW level enables a

single-ended input mode (VO, FSE0); see Table 5 and Table 6

input pad; push pull; CMOS

GND die

pad die

pad 8 6 - ground supply[2]

VCC(I/O) 7797- supply voltage for digital I/O pins (1.65 to 3.6 V). When VCC(I/O) is not

connected, the (D+, D−) pins are in three-state; this supply pin is totally

independent of VCC(5.0) and Vreg(3.3) and must never exceed the Vreg(3.3)

voltage

SPEED 8 8 10 8 I speed selection input (CMOS level with respect to VCC(I/O)); adjusts the

slew rate of differential data outputs D+ and D− according to the

transmission speed

LOW — low-speed (1.5 Mbit/s)

HIGH — full-speed (12 Mbit/s)

input pad; push pull; CMOS

D−9 9 11 9 AI/O negative USB data bus connection (analog, differential); for low-speed

mode connect to pin Vpu(3.3) via a 1.5 kΩ resistor

D+10 10 12 10 AI/O positive USB data bus connection (analog, differential); for full-speed mode

connect to pin Vpu(3.3) via a 1.5 kΩ resistor

Philips Semiconductors ISP1105/1106

Advanced USB transceivers

Product data Rev. 08 — 19 February 2004 6 of 28

[1] Symbol names with an overscore (e.g. NAME) indicate active LOW signals.

[2] ISP1105: ground terminal is connected to the exposed die pad (heatsink).

VPO/VO 11 11 - - I driver data input (CMOS level with respect to VCC(I/O), Schmitt trigger); see

Table 5 and Table 6

input pad; push pull; CMOS

VPO - - 13 11

VO ----

VMO/FSE0 12 12 - - I driver data input (CMOS level with respect to VCC(I/O), Schmitt trigger); see

Table 5 and Table 6

input pad; push pull; CMOS

VMO - - 14 12

FSE0 - - - -

Vreg(3.3) 13 13 15 13 - internal regulator option: regulated supply voltage output (3.0 to 3.6 V)

during 5 V operation; a decoupling capacitor of at least 0.1 µF is required

regulator bypass option: used as a supply voltage input for 3.3 V ±10%

operation

VCC(5.0) 14 14 16 14 - internal regulator option: supply voltage input (4.0 to 5.5 V); can be

connected directly to USB supply VBUS

regulator bypass option: connect to Vreg(3.3)

Vpu(3.3) 15 15 1 15 - pull-up supply voltage (3.3 V ±10%); connect an external 1.5 kΩresistor on

D+ (full-speed) or D− (low-speed); pin function is controlled by input

SOFTCON

SOFTCON = LOW — Vpu(3.3) ﬂoating (high impedance); ensures zero

pull-up current

SOFTCON = HIGH — Vpu(3.3) = 3.3 V; internally connected to Vreg(3.3)

SOFTCON 16 16 2 16 I software controlled USB connection input; a HIGH level applies 3.3 V to pin

Vpu(3.3), which is connected to an external 1.5 kΩ pull-up resistor; this

allows USB connect/disconnect signalling to be controlled by software

input pad; push pull; CMOS

Table 3: Pin description

…continued

Symbol[1] Pin Type Description

ISP1105 ISP1106

BS W DH W

Philips Semiconductors ISP1105/1106

Advanced USB transceivers

Product data Rev. 08 — 19 February 2004 7 of 28

7. Functional description

7.1 Function selection

[1] Signal levels on (D+, D−) are determined by other USB devices and external pull-up/down resistors.

[2] In ‘suspend’ mode (SUSPND = HIGH) the differential receiver is inactive and output RCV is always

LOW. Out-of-suspend (‘K’) signalling is detected via the single-ended receivers VP and VM.

[3] During suspend, the slew-rate control circuit of low-speed operation is disabled. The (D+, D−) lines

are still driven to their intended states, without slew-rate control. This is permitted because driving

during suspend is used to signal remote wake-up by driving a ‘K’ signal (one transition from idle to

‘K’ state) for a period of 1 to 15 ms.

7.2 Operating functions

[1] VP = VM = H indicates the sharing mode (VCC(5.0) and Vreg(3.3) are disconnected).

[2] RCV* denotes the signal level on output RCV just before SE0 state occurs. This level is stable during

the SE0 period.

Table 4: Function table

SUSPND OE (D+, D−) RCV VP/VM Function

L L driving and

receiving active active normal driving

(differential receiver active)

L H receiving[1] active active receiving

H L driving inactive[2] active driving during ‘suspend’[3]

(differential receiver inactive)

H H high-Z[1] inactive[2] active low-power state

Table 5: Driving function (pin OE = L) using single-ended input data interface for

ISP1105 (pin MODE = L)

FSE0 VO Data

L L differential logic 0

L H differential logic 1

H L SE0

H H SE0

Table 6: Driving function (pin OE = L) using differential input data interface for

ISP1105 (pin MODE = H) and ISP1106

VMO VPO Data

L L SE0

L H differential logic 1

H L differential logic 0

H H illegal state

Table 7: Receiving function (pin OE=H)

(D+, D−) RCV VP[1] VM[1]

Differential logic 0 L L H

Differential logic 1 H H L

SE0 RCV*[2] LL

Philips Semiconductors ISP1105/1106

Advanced USB transceivers

Product data Rev. 08 — 19 February 2004 8 of 28

7.3 Power supply conﬁgurations

The ISP1105/1106 can be used with different power supply conﬁgurations, which can

be changed dynamically. An overview is given in Table 9.

Normal mode — Both VCC(I/O) and VCC(5.0) or (VCC(5.0) and Vreg(3.3)) are connected.

For 5 V operation, VCC(5.0) is connected to a 5 V source (4.0 to 5.5 V). The internal

voltage regulator then produces 3.3 V for the USB connections. For 3.3 V operation,

both VCC(5.0) and Vreg(3.3) are connected to a 3.3 V source (3.0 to 3.6 V). VCC(I/O) is

independently connected to a voltage source (1.65 V to 3.6 V), depending on the

supply voltage of the external circuit.

Disable mode — VCC(I/O) is not connected, VCC(5.0) or (VCC(5.0) and Vreg(3.3)) are

connected. In this mode, the internal circuits of the ISP1105/1106 ensure that the

(D+, D−) pins are in three-state and the power consumption drops to the low-power

(suspended) state level. Some hysteresis is built into the detection of VCC(I/O) lost.

Sharing mode — VCC(I/O) is connected, (VCC(5.0) and Vreg(3.3)) are not connected. In

this mode, the (D+, D−) pins are made three-state and the ISP1105/1106 allows

external signals of up to 3.6 V to share the (D+, D−) lines. The internal circuits of the

ISP1105/1106 ensure that virtually no current (maximum 10 µA) is drawn via the (D+,

D−) lines. The power consumption through pin VCC(I/O) drops to the low-power

(suspended) state level. Both the VP and VM pins are driven HIGH to indicate this

mode. Pin RCV is made LOW. Some hysteresis is built into the detection of Vreg(3.3)

lost.

[1] High impedance or driven LOW.

[2] ISP1105 only.

Table 8: Pin states in disable or sharing mode

Pins Disable mode state Sharing mode state

VCC(5.0) / Vreg(3.3) 5 V input / 3.3 V output;

3.3 V input / 3.3 V input not present

VCC(I/O) not present 1.65 V to 3.6 V input

Vpu(3.3) high impedance (off) high impedance (off)

(D+, D−) high impedance high impedance

(VP, VM) invalid[1] H

RCV invalid[1] L

Inputs (VO/VPO, FSE0/VMO,

SPEED, MODE[2], SUSPND, OE,

SOFTCON)

high impedance high impedance

Philips Semiconductors ISP1105/1106

Advanced USB transceivers

Product data Rev. 08 — 19 February 2004 9 of 28

[1] High impedance or driven LOW.

7.4 Power supply input options

The ISP1105/1106 range has two power supply input options.

Internal regulator — VCC(5.0) is connected to 4.0 to 5.5 V. The internal regulator is

used to supply the internal circuitry with 3.3 V (nominal). The Vreg(3.3) pin becomes a

3.3 V output reference.

Regulator bypass — VCC(5.0) and Vreg(3.3) are connected to the same supply. The

internal regulator is bypassed and the internal circuitry is supplied directly from the

Vreg(3.3) power supply. The voltage range is 3.0 to 3.6 V to comply with the USB

speciﬁcation.

The supply voltage range for each input option is speciﬁed in Table 10.

Table 9: Power supply conﬁguration overview

VCC(5.0) or

Vreg(3.3)

VCC(I/O) Conﬁguration Special characteristics

Connected connected normal mode -

Connected not connected disable mode (D+, D−) and Vpu(3.3) high

impedance; VP, VM, RCV:

invalid[1]

Not connected connected sharing mode (D+, D−) and Vpu(3.3) high

impedance;

VP, VM driven HIGH;

RCV driven LOW

Table 10: Power supply input options

Input option VCC(5.0) Vreg(3.3) VCC(I/O)

Internal regulator supply input for internal

regulator

(4.0 to 5.5 V)

voltage reference

output

(3.3 V, 300 µA)

supply input for digital

I/O pins

(1.65 V to 3.6 V)

Regulator

bypass connected to Vreg(3.3)

with maximum voltage

drop of 0.3 V

(2.7 to 3.6 V)

supply input

(3.0 V to 3.6 V) supply input for digital

I/O pins

(1.65 V to 3.6 V)

Philips Semiconductors ISP1105/1106

Advanced USB transceivers

Product data Rev. 08 — 19 February 2004 10 of 28

8. Electrostatic discharge (ESD)

8.1 ESD protection

The pins that are connected to the USB connector (D+, D−,V

CC(5.0) and GND) have a

minimum of ±12 kV ESD protection. The ±12 kV measurement is limited by the test

equipment. Capacitors of 4.7 µF connected from Vreg(3.3) to GND and VCC(5.0) to GND

are required to achieve this ±12 kV ESD protection (see Figure 6).

ISP1105/1106 can withstand ±12 kV using the Human Body Model and ±5 kV using

the Contact Discharge Method as speciﬁed in

IEC 61000-4-2

8.2 ESD test conditions

A detailed report on test set-up and results is available on request.

Fig 6. Human Body ESD test model.

1 MΩ1500 Ω

HIGH VOLTAGE

DC SOURCE

4.7 µF

RCRD

VCC(5.0)

Vreg(3.3)

DEVICE UNDER

TEST

100 pF storage

capacitor

charge current

limit resistor discharge

resistance

GND

004aaa145

Philips Semiconductors ISP1105/1106

Advanced USB transceivers

Product data Rev. 08 — 19 February 2004 11 of 28

9. Limiting values

[1] Testing equipment limits measurement to only ±12 kV. Capacitors needed on VCC(5.0) and Vreg(3.3); see Section 8.

[2] Equivalent to discharging a 100 pF capacitor via a 1.5 kΩ resistor (Human Body Model).

10. Recommended operating conditions

Table 11: Absolute maximum ratings

In accordance with the Absolute Maximum Rating System (IEC 60134).

Symbol Parameter Conditions Min Max Unit

VCC(5.0) supply voltage −0.5 +6.0 V

VCC(I/O) I/O supply voltage −0.5 +4.6 V

Vreg(3.3) regulated supply voltage −0.5 +4.6 V

VIDC input voltage −0.5 VCC(I/O) +0.5 V

Ilu latch-up current VI=−1.8 to 5.4 V - 100 mA

Vesd electrostatic discharge voltage ILI <1µA[1][2]

on pins D+, D−,

VCC(5.0) and GND −12000 +12000 V

on other pins −2000 +2000 V

Tstg storage temperature −40 +125 °C

Table 12: Recommended operating conditions

Symbol Parameter Conditions Min Typ Max Unit

VCC(5.0) supply voltage (internal

regulator option) 5 V operation 4.0 5.0 5.5 V

Vreg(3.3) supply voltage (regulator

bypass option) 3.3 V operation 3.0 3.3 3.6 V

VCC(I/O) I/O supply voltage 1.65 - 3.6 V

VIinput voltage 0 - VCC(I/O) V

VI(AI/O) input voltage on analog I/O

pins (D+/D−)0 - 3.6 V

Tamb operating ambient temperature −40 - +85 °C

Philips Semiconductors ISP1105/1106

Advanced USB transceivers

Product data Rev. 08 — 19 February 2004 12 of 28

11. Static characteristics

[1] Iload includes the pull-up resistor current via pin Vpu(3.3).

[2] In ‘suspend’ mode, the minimum voltage is 2.7 V.

[3] Maximum value is characterized only, not tested in production.

[4] Excluding any load current and Vpu(3.3)/Vsw source current to the 1.5 kΩ and 15 kΩpull-up and pull-down resistors (200 µA typ.).

[5] When VCC(I/O) < 2.7 V, the minimum value for Vth(reg3.3)(present) is 2.0 V.

Table 13: Static characteristics: supply pins

= 4.0 to 5.5 V or V

reg(3.3)

= 3.0 to 3.6 V; V

CC(I/O)

= 1.65 to 3.6 V; V

GND

= 0 V; see Table 10 for valid voltage level

combinations; T

amb

−

40 to

C; unless otherwise speciﬁed.

Symbol Parameter Conditions Min Typ Max Unit

Vreg(3.3) regulated supply voltage

output internal regulator option;

Iload ≤300 µA[1][2] 3.0 3.3 3.6 V

ICC operating supply current full-speed transmitting and

receivingat 12 Mbit/s; CL=50pF

on D+/D−

[3] - 48mA

ICC(I/O) operating I/O supply current full-speed transmitting and

receiving at 12 Mbit/s [3] - 12mA

ICC(idle) supply current during

full-speed idle and SE0 full-speed idle: VD+> 2.7 V,

VD−< 0.3 V; SE0: VD+< 0.3 V,

VD−< 0.3 V

[4] - - 500 µA

ICC(I/O)(static) static I/O supply current full-speed idle, SE0 or suspend - - 20 µA

ICC(susp) suspend supply current SUSPND = HIGH [4] --20µA

ICC(dis) disable mode supply current VCC(I/O) not connected [4] --20µA

ICC(I/O)(sharing) sharing mode I/O supply

current VCC(5.0) or Vreg(3.3) not connected - - 20 µA

IDx(sharing) sharing mode load current

on pins D+ and D−VCC(5.0) orVreg(3.3) notconnected;

SOFTCON = LOW; VDx = 3.6 V --10µA

Vreg(3.3)th regulated supply voltage

detection threshold 1.65 V ≤VCC(I/O) ≤Vreg(3.3);

2.7 V ≤Vreg(3.3) ≤3.6 V

supply lost - - 0.8 V

supply present [5] 2.4 - - V

Vreg(3.3)hys regulated supply voltage

detection hysteresis VCC(I/O) = 1.8 V - 0.45 - V

VCC(I/O)th I/O supply voltage detection

threshold Vreg(3.3) = 2.7 to 3.6 V

supply lost - - 0.5 V

supply present 1.4 - - V

VCC(I/O)hys I/O supply voltage detection

hysteresis Vreg(3.3) = 3.3 V - 0.45 - V

Philips Semiconductors ISP1105/1106

Advanced USB transceivers

Product data Rev. 08 — 19 February 2004 13 of 28

Table 14: Static characteristics: digital pins

CC(I/O)

= 1.65 to 3.6 V; V

GND

=0V; T

amb

−

40 to

C; unless otherwise speciﬁed.

Symbol Parameter Conditions Min Typ Max Unit

VCC(I/O) = 1.65 to 3.6 V

Input levels

VIL LOW-level input voltage - - 0.3VCC(I/O) V

VIH HIGH-level input voltage 0.6VCC(I/O) -- V

Output levels

VOL LOW-level output voltage IOL = 100 µA - - 0.15 V

IOL = 2 mA - - 0.4 V

VOH HIGH-level output voltage IOH = 100 µAV

CC(I/O) −0.15 - - V

IOH = 2 mA VCC(I/O) −0.4 - - V

Leakage current

ILI input leakage current −1-+1µA

Example 1: VCC(I/O) = 1.8 V ±0.15 V

Input levels

VIL LOW-level input voltage - - 0.5 V

VIH HIGH-level input voltage 1.2 - - V

Output levels

VOL LOW-level output voltage IOL = 100 µA - - 0.15 V

IOL = 2 mA - - 0.4 V

VOH HIGH-level output voltage IOH = 100 µA 1.5 - - V

IOH = 2 mA 1.25 - - V

Example 2: VCC(I/O) = 2.5 V ±0.2 V

Input levels

VIL LOW-level input voltage - - 0.7 V

VIH HIGH-level input voltage 1.7 - - V

Output levels

VOL LOW-level output voltage IOL = 100 µA - - 0.15 V

IOL = 2 mA - - 0.4 V

VOH HIGH-level output voltage IOH = 100 µA 2.15 - - V

IOH = 2 mA 1.9 - - V

Example 3: VCC(I/O) = 3.3 V ±0.3 V

Input levels

VIL LOW-level input voltage - - 0.9 V

VIH HIGH-level input voltage 2.15 - - V

Output levels

VOL LOW-level output voltage IOL = 100 µA - - 0.15 V

IOL = 2 mA - - 0.4 V

VOH HIGH-level output voltage IOH = 100 µA 2.85 - - V

IOH = 2 mA 2.6 - - V

Capacitance

CIN input capacitance pin to GND - - 10 pF

Philips Semiconductors ISP1105/1106

Advanced USB transceivers

Product data Rev. 08 — 19 February 2004 14 of 28

[1] VOH(min) =V

reg(3.3) −0.2 V.

[2] Includes external resistors of 33 Ω±1% on both D+ and D−.

[3] This voltage is available at pins Vreg(3.3) and Vpu(3.3).

[4] In ‘suspend’ mode the minimum voltage is 2.7 V.

Table 15: Static characteristics: analog I/O pins (D+, D−)

= 4.0 to 5.5 V or V

reg(3.3)

= 3.0 to 3.6 V; V

GND

=0V; T

amb

−

40 to

C; unless otherwise speciﬁed.

Symbol Parameter Conditions Min Typ Max Unit

Input levels

Differential receiver

VDI differential input sensitivity |VI(D+)−VI(D−)|0.2 - - V

VCM differential common mode

voltage includes VDI range 0.8 - 2.5 V

Single-ended receiver

VIL LOW-level input voltage - - 0.8 V

VIH HIGH-level input voltage 2.0 - - V

Vhys hysteresis voltage 0.4 - 0.7 V

Output levels

VOL LOW-level output voltage RL= 1.5 kΩ to +3.6 V - - 0.3 V

VOH HIGH-level output voltage RL=15kΩ to GND [1] 2.8 - 3.6 V

Leakage current

ILZ OFF-state leakage current −1- +1µA

Capacitance

CIN transceiver capacitance pin to GND - - 20 pF

Resistance

ZDRV driver output impedance steady-state drive [2] 34 39 44 Ω

ZINP input impedance 10 - - MΩ

RSW internal switch resistance at

pin Vpu(3.3)

--10Ω

Termination

VTERM termination voltage for

upstream port pull-up (RPU)[3][4] 3.0 - 3.6 V

Philips Semiconductors ISP1105/1106

Advanced USB transceivers

Product data Rev. 08 — 19 February 2004 15 of 28

12. Dynamic characteristics

Table 16: Dynamic characteristics: analog I/O pins (D+, D−)[1]

= 4.0 to 5.5 V or V

reg(3.3)

= 3.0 to 3.6 V; V

CC(I/O)

= 1.65 to 3.6 V; V

GND

= 0 V; see Table 10 for valid voltage level

combinations; T

amb

−

40 to

C; unless otherwise speciﬁed.

Symbol Parameter Conditions Min Typ Max Unit

Driver characteristics

Full-speed mode

tFR rise time CL= 50 to 125 pF;

10% to 90% of |VOH −VOL|;

see Figure 7

4 - 20 ns

tFF fall time CL= 50 to 125 pF;

90% to 10% of |VOH −VOL|;

see Figure 7

4 - 20 ns

FRFM differential rise/fall time

matching (tFR/tFF)excluding the ﬁrst transition from

idle state 90 - 111.1 %

VCRS output signal crossover

voltage excluding the ﬁrst transition from

idle state; see Figure 10 [2] 1.3 - 2.0 V

Low-speed mode

tLR rise time CL= 50 to 600 pF;

10% to 90% of |VOH −VOL|;

see Figure 7

75 - 300 ns

tLF fall time CL= 50 to 600 pF;

90% to 10% of |VOH −VOL|;

see Figure 7

75 - 300 ns

LRFM differential rise/fall time

matching (tLR/tLF)excluding the ﬁrst transition from

idle state 80 - 125 %

VCRS output signal crossover

voltage excluding the ﬁrst transition from

idle state; see Figure 10 [2] 1.3 - 2.0 V

Driver timing

Full-speed mode

tPLH(drv) driver propagation delay

(VO/VPO, FSE0/VMO to

D+,D−)

LOW-to-HIGH; see Figure 10 --18ns

tPHL(drv) driver propagation delay

(VO/VPO, FSE0/VMO to

D+,D−)

HIGH-to-LOW; see Figure 10 --18ns

tPHZ driver disable delay (OE to

D+,D−)HIGH-to-OFF; see Figure 8 --15ns

tPLZ driver disable delay (OE to

D+,D−)LOW-to-OFF; see Figure 8 --15ns

tPZH driver enable delay (OE to

D+,D−)OFF-to-HIGH; see Figure 8 --15ns

tPZL driver enable delay (OE to

D+,D−)OFF-to-LOW; see Figure 8 --15ns

Low-speed mode

Not speciﬁed: low-speed delay timings are dominated by the slow rise/fall times tLR and tLF.

Philips Semiconductors ISP1105/1106

Advanced USB transceivers

Product data Rev. 08 — 19 February 2004 16 of 28

[1] Test circuit: see Figure 13.

[2] Characterized only, not tested. Limits guaranteed by design.

Receiver timings (full-speed and low-speed mode)

Differential receiver

tPLH(rcv) propagation delay (D+,D−to

RCV) LOW-to-HIGH; see Figure 9 --15ns

tPHL(rcv) propagation delay (D+,D−to

RCV) HIGH-to-LOW; see Figure 9 --15ns

Single-ended receiver

tPLH(se) propagation delay (D+,D−to

VP, VM) LOW-to-HIGH; see Figure 9 --18ns

tPHL(se) propagation delay (D+,D−to

VP, VM) HIGH-to-LOW; see Figure 9 --18ns

Table 16: Dynamic characteristics: analog I/O pins (D+, D−)[1]

…continued

= 4.0 to 5.5 V or V

reg(3.3)

= 3.0 to 3.6 V; V

CC(I/O)

= 1.65 to 3.6 V; V

GND

= 0 V; see Table 10 for valid voltage level

combinations; T

amb

−

40 to

C; unless otherwise speciﬁed.

Symbol Parameter Conditions Min Typ Max Unit

Fig 7. Rise and fall times. Fig 8. Timing of OE to D+, D−.

Fig 9. Timing of D+, D− to RCV, VP, VM. Fig 10. Timing of VO/VPO, FSE0/VMO to D+, D−.

MGS963

VOL

tFR, tLR tFF, tLF

VOH 90 %

10 % 10 %

90 %

MGS966

VOL

VOH

tPZH

tPZL tPHZ

tPLZ

VOH −0.3 V

VOL +0.3 V

VCRS

0.9 V

1.8 V

0 V

logic input

differential

data lines

MGS965

VOL

VOH

tPHL(rcv)

tPHL(se)

tPLH(rcv)

tPLH(se)

VCRS VCRS

0.9 V

2.0 V

0.8 V

logic output

differential

data lines

MGS964

VOL

VOH

tPHL(drv)

tPLH(drv)

VCRS VCRS

0.9 V

1.8 V

0 V

logic input

differential

data lines

Philips Semiconductors ISP1105/1106

Advanced USB transceivers

Product data Rev. 08 — 19 February 2004 17 of 28

13. Test information

V = 0 V for tPZH, tPHZ

V=V

reg(/3.3) for tPZL, tPLZ

Fig 11. Load for enable and disable times.

Fig 12. Load for VM, VP and RCV.

Load capacitance:

CL= 50 pF or 125 pF (full-speed mode, minimum or maximum timing)

CL= 50 pF or 600 pF (low-speed mode, minimum or maximum timing)

(1) Full-speed mode: connected to D+; low-speed mode: connected to D−.

Fig 13. Load for D+, D−.

test point

33 Ω

D.U.T. 500 Ω

50 pF

MBL142

MGS968

25 pF

test point

D.U.T.

MGS967

test point

15 kΩ

D+/D−

Vpu(3.3)

1.5 kΩ(1)

33 Ω

D.U.T.

Philips Semiconductors ISP1105/1106

Advanced USB transceivers

Product data Rev. 08 — 19 February 2004 18 of 28

14. Package outline

Fig 14. HBCC16 package outline.

2.5

A1bA2

UNIT DEhe1

REFERENCES

OUTLINE

VERSION EUROPEAN

PROJECTION ISSUE DATE

01-11-13

03-03-12

IEC JEDEC JEITA

mm 0.8 0.10

0.05 0.7

0.6 3.1

2.9 1.45

1.35

3.1

2.9

1.45

1.35

0.33

0.27

DIMENSIONS (mm are the original dimensions)

SOT639-2 MO-217

0.33

0.27

0.38

0.32

0.38

0.32

2.45

0.23

0.17

0.5

we yy

0.1 0.05 0.2

2.5

2.45

0.08

0 2.5 5 mm

scale

SOT639-2

HBCC16: plastic thermal enhanced bottom chip carrier; 16 terminals; body 3 x 3 x 0.65 mm

max.

detail X

y1C

113

1/2 e3

1/2 e4

terminal 1

index area

Philips Semiconductors ISP1105/1106

Advanced USB transceivers

Product data Rev. 08 — 19 February 2004 19 of 28

Fig 15. HVQFN16 package outline.

terminal 1

index area

0.51

A1Eh

UNIT y

0.2

REFERENCES

OUTLINE

VERSION EUROPEAN

PROJECTION ISSUE DATE

IEC JEDEC JEITA

mm 3.1

2.9

1.75

1.45

3.1

2.9 1.75

1.45

1.5

0.30

0.18

0.05

0.00 0.05 0.1

DIMENSIONS (mm are the original dimensions)

SOT758-1 MO-220 - - -- - -

0.5

0.3

0.1

0.05

0 2.5 5 mm

scale

SOT758-1

HVQFN16: plastic thermal enhanced very thin quad flat package; no leads;

16 terminals; body 3 x 3 x 0.85 mm

A(1)

max.

AA1c

detail X

y1C

16 13

02-03-25

02-10-21

terminal 1

index area

1/2 e

E(1)

Note

1. Plastic or metal protrusions of 0.075 mm maximum per side are not included.

D(1)

Philips Semiconductors ISP1105/1106

Advanced USB transceivers

Product data Rev. 08 — 19 February 2004 20 of 28

Fig 16. TSSOP16 package outline.

UNIT A1A2A3bpcD

(1) E(2) (1)

ELL

pQZywv θ

REFERENCES

OUTLINE

VERSION EUROPEAN

PROJECTION ISSUE DATE

IEC JEDEC JEITA

mm 0.15

0.05 0.95

0.80 0.30

0.19 0.2

0.1 5.1

4.9 4.5

4.3 0.65 6.6

6.2 0.4

0.3 0.40

0.06 8

0.13 0.10.21

DIMENSIONS (mm are the original dimensions)

Notes

1. Plastic or metal protrusions of 0.15 mm maximum per side are not included.

2. Plastic interlead protrusions of 0.25 mm maximum per side are not included.

0.75

0.50

SOT403-1 MO-153 99-12-27

03-02-18

0.25

16 9

detail X

(A )

vMA

0 2.5 5 mm

scale

TSSOP16: plastic thin shrink small outline package; 16 leads; body width 4.4 mm SOT403-1

max.

1.1

pin 1 index

Philips Semiconductors ISP1105/1106

Advanced USB transceivers

Product data Rev. 08 — 19 February 2004 21 of 28

15. Packaging

The ISP1105/1106W (HBCC16 package) is delivered on a type A carrier tape, see

Figure 17. The tape dimensions are given in Table 17.

The reel diameter is 330 mm. The reel is made of polystyrene (PS) and is not

designed for use in a baking process.

The cumulative tolerance of 10 successive sprocket holes is ±0.02 mm. The camber

must not exceed 1 mm in 100 mm.

Fig 17. Carrier tape dimensions.

Table 17: Type A carrier tape dimensions for ISP1105/1106W

Dimension Value Unit

A03.3 mm

B03.3 mm

K01.1 mm

P18.0 mm

W 12.0 ±0.3 mm

dth

MLC338

Type B

Type A

4K0

elongated

sprocket hole

direction of feed

Philips Semiconductors ISP1105/1106

Advanced USB transceivers

Product data Rev. 08 — 19 February 2004 22 of 28

16. Soldering

16.1 Introduction to soldering surface mount packages

This text gives a very brief insight to a complex technology. A more in-depth account

of soldering ICs can be found in our

Data Handbook IC26; Integrated Circuit

Packages

(document order number 9398 652 90011).

There is no soldering method that is ideal for all surface mount IC packages. Wave

soldering can still be used for certain surface mount ICs, but it is not suitable for ﬁne

pitch SMDs. In these situations reﬂow soldering is recommended. In these situations

reﬂow soldering is recommended.

16.2 Reﬂow soldering

Reﬂow soldering requires solder paste (a suspension of ﬁne solder particles, ﬂux and

binding agent) to be applied to the printed-circuit board by screen printing, stencilling

or pressure-syringe dispensing before package placement. Driven by legislation and

environmental forces the worldwide use of lead-free solder pastes is increasing.

Several methods exist for reﬂowing; for example, convection or convection/infrared

heating in a conveyor type oven. Throughput times (preheating, soldering and

cooling) vary between 100 and 200 seconds depending on heating method.

Typical reﬂow peak temperatures range from 215 to 270 °C depending on solder

paste material. The top-surface temperature of the packages should preferably be

kept:

•below 225 °C (SnPb process) or below 245 °C (Pb-free process)

–for all BGA, HTSSON..T and SSOP..T packages

–for packages with a thickness ≥2.5 mm

–for packages with a thickness < 2.5 mm and a volume ≥350 mm3 so called

thick/large packages.

•below 240 °C (SnPb process) or below 260 °C (Pb-free process) for packages with

a thickness < 2.5 mm and a volume < 350 mm3 so called small/thin packages.

Moisture sensitivity precautions, as indicated on packing, must be respected at all

times.

16.3 Wave soldering

Conventional single wave soldering is not recommended for surface mount devices

(SMDs) or printed-circuit boards with a high component density, as solder bridging

and non-wetting can present major problems.

To overcome these problems the double-wave soldering method was speciﬁcally

developed.

If wave soldering is used the following conditions must be observed for optimal

results:

•Use a double-wave soldering method comprising a turbulent wave with high

upward pressure followed by a smooth laminar wave.

Philips Semiconductors ISP1105/1106

Advanced USB transceivers

Product data Rev. 08 — 19 February 2004 23 of 28

•For packages with leads on two sides and a pitch (e):

–larger than or equal to 1.27 mm, the footprint longitudinal axis is preferred to be

parallel to the transport direction of the printed-circuit board;

–smaller than 1.27 mm, the footprint longitudinal axis must be parallel to the

transport direction of the printed-circuit board.

The footprint must incorporate solder thieves at the downstream end.

•For packages with leads on four sides, the footprint must be placed at a 45° angle

to the transport direction of the printed-circuit board. The footprint must

incorporate solder thieves downstream and at the side corners.

During placement and before soldering, the package must be ﬁxed with a droplet of

adhesive. The adhesive can be applied by screen printing, pin transfer or syringe

dispensing. The package can be soldered after the adhesive is cured.

Typical dwell time of the leads in the wave ranges from 3 to 4 seconds at 250 °C or

265 °C, depending on solder material applied, SnPb or Pb-free respectively.

A mildly-activated ﬂux will eliminate the need for removal of corrosive residues in

most applications.

16.4 Manual soldering

Fix the component by ﬁrst soldering two diagonally-opposite end leads. Use a low

voltage (24 V or less) soldering iron applied to the ﬂat part of the lead. Contact time

must be limited to 10 seconds at up to 300 °C.

When using a dedicated tool, all other leads can be soldered in one operation within

2 to 5 seconds between 270 and 320 °C.

16.5 Package related soldering information

[1] For more detailed information on the BGA packages refer to the

(LF)BGA Application Note

(AN01026); order a copy from your Philips Semiconductors sales ofﬁce.

[2] All surface mount (SMD) packages are moisture sensitive. Depending upon the moisture content, the

maximum temperature (with respect to time) and body size of the package, there is a risk that internal

or external package cracks may occur due to vaporization of the moisture in them (the so called

popcorn effect). For details, refer to the Drypack information in the

Data Handbook IC26; Integrated

Circuit Packages; Section: Packing Methods

Table 18: Suitability of surface mount IC packages for wave and reﬂow soldering

methods

Package[1] Soldering method

Wave Reﬂow[2]

BGA, HTSSON..T[3], LBGA, LFBGA, SQFP,

SSOP..T[3], TFBGA, USON, VFBGA not suitable suitable

DHVQFN, HBCC, HBGA, HLQFP, HSO, HSOP,

HSQFP, HSSON, HTQFP, HTSSOP, HVQFN,

HVSON, SMS

not suitable[4] suitable

PLCC[5], SO, SOJ suitable suitable

LQFP, QFP, TQFP not recommended[5][6] suitable

SSOP, TSSOP, VSO, VSSOP not recommended[7] suitable

CWQCCN..L[8], PMFP[9], WQCCN..L[8] not suitable not suitable

Philips Semiconductors ISP1105/1106

Advanced USB transceivers

Product data Rev. 08 — 19 February 2004 24 of 28

[3] These transparent plastic packages are extremely sensitive to reﬂow soldering conditions and must

on no account be processed through more than one soldering cycle or subjected to infrared reﬂow

soldering with peak temperature exceeding 217 °C±10 °C measured in the atmosphere of the reﬂow

oven. The package body peak temperature must be kept as low as possible.

[4] These packages are not suitable for wave soldering. On versions with the heatsink on the bottom

side, the solder cannot penetrate between the printed-circuit board and the heatsink. On versions with

the heatsink on the top side, the solder might be deposited on the heatsink surface.

[5] If wave soldering is considered, then the package must be placed at a 45° angle to the solder wave

direction. The package footprint must incorporate solder thieves downstream and at the side corners.

[6] Wave soldering is suitable for LQFP, QFP and TQFP packages with a pitch (e) larger than 0.8 mm; it

is deﬁnitely not suitable for packages with a pitch (e) equal to or smaller than 0.65 mm.

[7] Wave soldering is suitable for SSOP, TSSOP, VSO and VSOP packages with a pitch (e) equal to or

larger than 0.65 mm; it is deﬁnitely not suitable for packages with a pitch (e) equal to or smaller than

0.5 mm.

[8] Image sensor packages in principle should not be soldered. They are mounted in sockets or delivered

pre-mounted on ﬂex foil. However, the image sensor package can be mounted by the client on a ﬂex

foil by using a hot bar soldering process. The appropriate soldering proﬁle can be provided on

request.

[9] Hot bar soldering or manual soldering is suitable for PMFP packages.

Philips Semiconductors ISP1105/1106

Advanced USB transceivers

Product data Rev. 08 — 19 February 2004 25 of 28

17. Additional soldering information

17.1 (H)BCC packages: footprint

The surface material of the terminals on the resin protrusion consists of a 4-layer

metal structure (Au, Pd, Ni and Pd). The Au + Pd layer (0.1 µm min.) ensures

solderability, the Ni layer (5 µm min.) prevents diffusion, and the Pd layer on top

(0.5 µm min.) ensures effective wire bonding.

17.2 (H)BCC packages: reﬂow soldering proﬁle

The conditions for reﬂow soldering of (H)BCC packages are as follows:

•Preheating time: minimum 90 s at T = 145 to 155 °C

•Soldering time: minimum 90 s (BCC) or minimum 100 s (HBCC) at T > 183 °C

•Peak temperature:

–Ambient temperature: Tamb(max) = 260 °C

–Device surface temperature: Tcase(max) = 255 °C.

Cavity: exposed die pad, either functioning as heatsink or as ground connection; only for HBCC packages.

Fig 18. (H)BCC footprint and solder resist mask dimensions.

004aaa123

0.05

All dimensions in mm

For exact dimensions

see package outline

drawing (SOT639-2)

Normal

Terminal PCB land Solder resist mask Stencil mask

Solder land

Corner

0.05

0.1

(4×)

0.3 (8×)

0.05

Solder resist

Solder stencil

Stencil print thickness:

0.1 to 0.12 mm

Cavity

0.05

Philips Semiconductors ISP1105/1106

Advanced USB transceivers

Product data Rev. 08 — 19 February 2004 26 of 28

18. Revision history

Table 19: Revision history

Rev Date CPCN Description

08 20040219 - Product data (9397 750 11231); removed ISP1107 related information.

Modiﬁcations:

•Changed the data sheet title from ISP1105/1106/1107 to ISP1105/1106 and removed all

information pertaining to ISP1107

•Changed USB 1.1 reference to USB 2.0; also added data transfer rates

•Added HVQFN16 package details in Table 1,Section 6 and Section 14

•Figure 1: removed the ﬁrst ﬁgure note

•Table 3: added pad details

•Table 11: updated

•Table 15: removed ZDRV2, and also table note 3

•Figure 8 and Figure 10: changed 1.65 V to 1.8 V.

07 20020329 - Product data (9397 750 09529)

06 20011130 - Product data; sixth version (9397 750 08872)

05 20010903 - Product data; ﬁfth version (9397 750 08681)

04 20010802 - Preliminary data; fourth version (9397 750 08643)

03 20010704 - Preliminary data; third version (9397 750 08515)

02 20010205 - Objective speciﬁcation; second version (9397 750 07879) ISP1107 stand-alone data

sheet only.

01 20000223 - Objective speciﬁcation; initial version (9397 750 06899) ISP1107 stand-alone data

sheet only.

9397 750 11231

Philips Semiconductors ISP1105/1106

Advanced USB transceivers

Product data Rev. 08 — 19 February 2004 27 of 28

Contact information

For additional information, please visit http://www.semiconductors.philips.com.

For sales ofﬁce addresses, send e-mail to: sales.addresses@www.semiconductors.philips.com.Fax: +31 40 27 24825

19. Data sheet status

[1] Please consult the most recently issued data sheet before initiating or completing a design.

[2] The product status of the device(s) described in this data sheet may have changed since this data sheet was published. The latest information is available on the Internet at

URL http://www.semiconductors.philips.com.

[3] For data sheets describing multiple type numbers, the highest-level product status determines the data sheet status.

20. Deﬁnitions

Short-form speciﬁcation — The data in a short-form speciﬁcation is

extracted from a full data sheet with the same type number and title. For

detailed information see the relevant data sheet or data handbook.

Limiting values deﬁnition — Limiting values given are in accordance with

the Absolute Maximum Rating System (IEC 60134). Stress above one or

more of the limiting values may cause permanent damage to the device.

These are stress ratings only and operation of the device at these or at any

other conditions above those given in the Characteristics sections of the

speciﬁcation is not implied. Exposure to limiting values for extended periods

may affect device reliability.

Application information — Applications that are described herein for any

of these products are for illustrative purposes only. Philips Semiconductors

make no representation or warranty that such applications will be suitable for

the speciﬁed use without further testing or modiﬁcation.

21. Disclaimers

Life support — These products are not designed for use in life support

appliances, devices, or systems where malfunction of these products can

reasonably be expected to result in personal injury. Philips Semiconductors

customers using or selling these products for use in such applications do so

at their own risk and agree to fully indemnify Philips Semiconductors for any

damages resulting from such application.

Right to make changes — Philips Semiconductors reserves the right to

make changes in the products - including circuits, standard cells, and/or

software - described or contained herein in order to improve design and/or

performance. When the product is in full production (status ‘Production’),

relevant changes will be communicated via a Customer Product/Process

Change Notiﬁcation (CPCN). Philips Semiconductors assumes no

responsibility or liability for the use of any of these products, conveys no

licence or title under any patent, copyright, or mask work right to these

products, and makes no representations or warranties that these products are

free from patent, copyright, or mask work right infringement, unless otherwise

speciﬁed.

Level Data sheet status[1] Product status[2][3] Deﬁnition

I Objective data Development This data sheet contains data from the objective speciﬁcation for product development. Philips

Semiconductors reserves the right to change the speciﬁcation in any manner without notice.

II Preliminary data Qualiﬁcation This data sheet contains data from the preliminary speciﬁcation. Supplementary data will be published

at a later date. Philips Semiconductors reserves the right to change the speciﬁcation without notice, in

order to improve the design and supply the best possible product.

III Product data Production This data sheet contains data from the product speciﬁcation. Philips Semiconductors reserves the

right to make changes at any time in order to improve the design, manufacturing and supply. Relevant

changes will be communicated via a Customer Product/Process Change Notiﬁcation (CPCN).

Printed in The Netherlands

All rights are reserved. Reproduction in whole or in part is prohibited without the prior

written consent of the copyright owner.

The information presented in this document does not form part of any quotation or

contract, is believed to be accurate and reliable and may be changed without notice. No

liability will be accepted by the publisher for any consequence of its use. Publication

thereof does not convey nor imply any license under patent- or other industrial or

intellectual property rights.

Date of release: 19 February 2004 Document order number: 9397 750 11231

Contents

Philips Semiconductors ISP1105/1106

Advanced USB transceivers

1 General description. . . . . . . . . . . . . . . . . . . . . . 1

2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

3 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

4 Ordering information. . . . . . . . . . . . . . . . . . . . . 2

4.1 Ordering options. . . . . . . . . . . . . . . . . . . . . . . . 2

5 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 3

6 Pinning information. . . . . . . . . . . . . . . . . . . . . . 4

6.1 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

6.2 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 5

7 Functional description . . . . . . . . . . . . . . . . . . . 7

7.1 Function selection. . . . . . . . . . . . . . . . . . . . . . . 7

7.2 Operating functions. . . . . . . . . . . . . . . . . . . . . . 7

7.3 Power supply conﬁgurations. . . . . . . . . . . . . . . 8

7.4 Power supply input options. . . . . . . . . . . . . . . . 9

8 Electrostatic discharge (ESD). . . . . . . . . . . . . 10

8.1 ESD protection . . . . . . . . . . . . . . . . . . . . . . . . 10

8.2 ESD test conditions . . . . . . . . . . . . . . . . . . . . 10

9 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . 11

10 Recommended operating conditions. . . . . . . 11

11 Static characteristics. . . . . . . . . . . . . . . . . . . . 12

12 Dynamic characteristics . . . . . . . . . . . . . . . . . 15

13 Test information. . . . . . . . . . . . . . . . . . . . . . . . 17

14 Package outline . . . . . . . . . . . . . . . . . . . . . . . . 18

15 Packaging. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

16 Soldering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

16.1 Introduction to soldering surface mount

packages . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

16.2 Reﬂow soldering. . . . . . . . . . . . . . . . . . . . . . . 22

16.3 Wave soldering. . . . . . . . . . . . . . . . . . . . . . . . 22

16.4 Manual soldering . . . . . . . . . . . . . . . . . . . . . . 23

16.5 Package related soldering information . . . . . . 23

17 Additional soldering information . . . . . . . . . . 25

17.1 (H)BCC packages: footprint . . . . . . . . . . . . . . 25

17.2 (H)BCC packages: reﬂow soldering proﬁle. . . 25

18 Revision history. . . . . . . . . . . . . . . . . . . . . . . . 26

19 Data sheet status. . . . . . . . . . . . . . . . . . . . . . . 27

20 Deﬁnitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

21 Disclaimers. . . . . . . . . . . . . . . . . . . . . . . . . . . . 27