FP-1310-5I-50SMF-FCAPC - Finisar Corporation

FEATURES:

Wide operating temperature

(-40°C to 85°C)

Stable threshold current for easy

transmitter control (T0~ 80K)

1310 nm typical emission

wavelength FP-LDs

Pigtailed package

High-speed modulation

capability (Up to 5Gb/s)

Excellent reliability

♦Ultra-low gradual

wear-out rates

♦<1% failures in 20 yrs at 55C

APPLICATION

Source for high-speed

data-communication and

telecommunication links

♦SONET, Fiber-channel,

Giag-bit Ethernet, FTTX

♦CATV / Satellite and other

analogue markets

1310 NM FABRY-PEROT (FP)

LASER DIODE

PIGTAILED PACKAGE

FP-1310-5I-XXX

Preliminary

DATA

SHEET

The FP-1310-5I-xxx is an MOCVD grown InAlGaAs ridge laser diode with

emission wave-length of 1310 nm and standard continuous light output of 5

mW per facet. These lasers provide stable, single transverse mode oscillation.

These are hermetically sealed devices with an integrated monitor photodiode

to monitor the optical output.

The TO-56 laser can is mounted inside a metal coaxial package which is then

pigtailed with a singlemode fiber and terminated with a fiber connector. The

pigtail comes in a choice of 50cm or 100cm lengths as standard, terminated

with either FC or SC connectors with an APC or UPC polish.

Suitable as a light source for data-com and telecom applications with data

rates up to 5 Gb/s.

Part Number Description

FP-1310-5I-50SMF-FCUPC 1310 nm Fabry-Perot (FP) Laser Diode, 50cm singlemode

pigtailed package, FC UPC connector.

FP-1310-5I-50SMF-FCAPC 1310 nm Fabry-Perot (FP) Laser Diode, 50cm singlemode

pigtailed package, FC APC connector.

FP-1310-5I-100SMF-SCUPC 1310 nm Fabry-Perot (FP) Laser Diode, 100cm singlemode

pigtailed package, SC UPC connector.

FP-1310-5I-100SMF-SCAPC 1310 nm Fabry-Perot (FP) Laser Diode, 100cm singlemode

pigtailed package, SC APC connector.

Other fiber lengths and connector options available on request.

FP-1310-5I-XXX 1310 NM FABRY-PEROT (FP) LASER DIODE

NOTICE: Stresses greater than those listed under “Absolute

Maximum Ratings” may cause permanent damage to the

device. This is a stress rating only and functional operation

of the device at these or any other conditions above those

indicated in the operations section for extended periods of

time may affect reliability.

NOTICE: The inherent design of this component causes it

to be sensitive to electrostatic discharge (ESD). To prevent

ESD-induced damage and/or degradation to equipment, take

normal ESD precautions when handling this product

ABSOLUTE MAXIMUM RATINGS

Symbol Parameter Conditions Rating

Unit

POOutput power CW 10

VRLD Reverse voltage (laser diode) - 2

VRPD Reverse voltage (monitor photodiode) -10

IFPD Forward current (photodiode) - 1

TcOperation temperature --40 to +85

°C

Tstg Storage temperature --40 to +100

°C

-ESD exposure level (human body model) -200

FP-1310-5I-XXX

ELECTRICAL-OPTICAL CHARACTERISTICS

Symbol Parameter Test Conditions Minimum Typical Maximum Unit

Poc Output power - pigtail end

CW, IF= 32mA 2.5 mW

Ith Threshold current CW 3 9 15 mA

IthH Threshold current

at 85°C

CW, Tc=85°C 21 30 mA

T0Temperature dependence of

threshold current

-80 - K

Iop Operating current For PO= 2mW (CW) -

Vop Operating voltage CW Voltage at Iop

1.15 1.4

Rop Differential series resistance

(laser diode)

CW dV/dI at T = 25°C

between 15 mA and 25 mA

4 7 12 Ω

SE Slope efficiency (fiber coupled)

0.1

W/A

SER SE Ratio SE @ 85°C / SE @ 25°C 0.6 0.8

SE @ 40°C / SE @ 25°C 1.4

ΔSE/ΔTSlope efficiency temperature

coefficient

-0.35 -0.65 %/°C

λcLasing wavelength 1290 1310 1330 nm

Δλ Spectral width under

modulation

PRBS 2^7-1 ER =10 dB; Ib =

1.8*Ith; RMS (sigma)

-1.5 2.75 nm

dλc/dT Temperature dependence of

lasing wavelength

0.40 0.45 0.55 nm/K

trRise time 20% - 80% ; Tc= 85°C;

ER = 10 dB; Ib = 1.8*Ith

- - 140 ps

tfFall time 20% - 80% ; Tc= 85°C;

ER =10 dB; Ib = 1.8*Ith

- - 140 ps

RIN Relative Intensity Noise CW, 0.95 to 5.45GHz, -20dBm

back reflection in worst case

polarization

-125 dB/Hz

TOIP Third order intercept point PO=2mW, F=5.45 to 5.452GHz,

85°C

15 dB

fRRelaxation oscillation

frequency

Tc= 85°C; I = Ith+36 mA 55.5 - GHz

CdCapacitance for monitor

photodiode

- 5 50 pF

Imon Monitor photodiode current

30 130

1000 μA

ΔTRACK Tracking error -1.5 -+1.5 dB

Im0 Dark current for Monitor

photodiode

- - 0.1 μA

Unless otherwise stated, all parameters are at TCASE = 25°C and referenced to pigtail power.

Iop = 32mA

FP-1310-5I-XXX 1310 NM FABRY-PEROT (FP) LASER DIODE

TYPICAL CHARACTERISTICS

85oC, 60mA

SS=41 85oC, 60mA

SS=41

0.4

0.8

1.2

1.6

2.0

10 20 30 40 50

Typical LI curve at Tc = 25oC, 45oC, 65oC and 85oC Typical IV curve at Tc = 25oC, 45oC, 65oC and 85oC

FP-1310-5I-XXX 1310 NM FABRY-PEROT (FP) LASER DIODE

TYPICAL CHARACTERISTICS

PIN OUT

FP-1310-5I-XXX 1310 NM FABRY-PEROT (FP) LASER DIODE

MOUNTING DIMENSIONS

(for reference only): Dimensions in millimeters

Number Function

1Ground

2LD Cathode

3PD Anode

4LD Anode / PD Cathode

Phone:1-866-MY-VCSEL USA (toll free)

1-214-509-2700 USA (Direct dial)

44 (0) 174 336 5533 Europe

886-935-409898 China & Taiwan

81-90-4437-1130 Japan

82-11-220-6153 Asia Pacific & Korea

Fax: 1-214-509-3709 USA

Email: salesAOCD@finisar.com

WEB: www.finisar.com/aoc.php

ADVANCED OPTICAL COMPONENTS

Finisar’s ADVANCED OPTICAL COMPONENTS division was

formed through strategic acquisition of key optical compon-

ent suppliers. The company has led the industry in high

volume Vertical Cavity Surface Emitting Laser (VCSEL) and

associated detector technology since 1996. VCSELs have

become the primary laser source for optical data communi-

cation, and are rapidly expanding into a wide variety of sensor

applications. VCSELs’ superior reliability, low drive current,

high coupled power, narrow and circularly symmetric beam

and versatile packaging options (including arrays) are enabling

solutions not possible with other optical technologies.

ADVANCED OPTICAL COMPONENTS is also a key supplier of

Fabrey-Perot (FP) and Distributed Feedback (DFB) Lasers, and

Optical Isolators (OI) for use in single mode fiber data and

telecommunications networks

LOCATION

Allen, TX - Business unit headquarters, VCSEL wafer

growth, wafer fabrication and TO package assembly.

Fremont, CA – Wafer growth and fabrication of 1310 to

1550nm FP and DFB lasers.

Shanghai, PRC – Optical passives assembly, including

optical isolators and splitters.

SALES AND SERVICE

Finisar’s ADVANCED OPTICAL COMPONENTS division serves its

customers through a worldwide network of sales offices and

distributors. For application assistance, current specifications,

pricing or name of the nearest Authorized Distributor, contact

a nearby sales office or call the number listed below.

AOC CAPABILITIES

ADVANCED OPTICAL COMPONENTS’ advanced capabilities

include:

1, 2, 4, 8, and 10Gbps serial VCSEL solutions

1, 2, 4, 8, and 10Gbps serial SW DETECTOR solutions

VCSEL and detector arrays

1, 2, 4, 8, and 10Gbps FP and DFB solutions at 1310 and

1550nm

1, 2, 4, 8, and 10Gbps serial LW DETECTOR solutions

Optical Isolators from 1260 to 1600nm range

Laser packaging in TO46, TO56, and Optical

subassemblies with SC, LC, and MU interfaces for

communication networks

VCSELs operating at 670nm, 780nm, 980nm, and 1310nm

in development

Sensor packages include surface mount, various plastics,

chip on board, chipscale packages, etc.

Custom packaging options

FP-1310-5I-XXX 1310 NM FABRY-PEROT (FP) LASER DIODE