Single-Channel: 6N135M, 6N136M, HCPL2503M, HCPL4502M, HCPL4503M
Dual-Channel: HCPL2530M, HCPL2531M — High Speed Transistor Optocouplers
©2008 Fairchild Semiconductor Corporation www.fairchildsemi.com
6N13XM, HCPLXXXM Rev. 1.0.1
October 2008
PRELIMINARY
Single-Channel: 6N135M, 6N136M, HCPL2503M,
HCPL4502M, HCPL4503M
Dual-Channel: HCPL2530M, HCPL2531M
High Speed Transistor Optocouplers
Features
■
High speed –1 MBit/s
■
Superior CMR – 10kV/µs
■
Dual-Channel HCPL2530M, HCPL2531M
(Preliminary)
■
CTR guaranteed 0–70°C
■
U.L. recognized (File # E90700, Vol. 2)
■
5,000Vrms (1 minute) isolation rating
■
Superior CMR of 15,000V/µs min. (HCPL4503M)
■
>8mm creepage and clearance (option T)
■
No base connection for improved noise immunity
(HCPL4502M, HCPL4503M)
Applications
■
Line receivers
■
Pulse transformer replacement
■
Output interface to CMOS-LSTTL-TTL
■
Wide bandwidth analog coupling
Description
The HCPL4502M, HCPL4503M, HCPL2503M, 6N135M,
6N136M, HCPL2530M and HCPL2531M optocouplers
consist of an AlGaAs LED optically coupled to a high
speed photodetector transistor.
A separate connection for the bias of the photodiode
improves the speed by several orders of magnitude over
conventional phototransistor optocouplers by reducing
the base-collector capacitance of the input transistor.
An internal noise shield provides superior common
mode rejection of up to 50,000V/µs.
Schematics Package Outlines
1
2
3
4 5
6
7
8
+
_
VF1
VCC
V01
V02
GND
VF2
_
+
HCPL2530M/HCPL2531M
1
2
3
4 5
6
7
8
+
_
VF
VCC
VB
VO
GNDN/C
N/C
6N135M, 6N136M, HCPL2503M,
HCPL4502M, HCPL4503M
Pin 7 is not connected in
HCPL4502M and HCPL4503M
8
8
1
8
1
1
©2008 Fairchild Semiconductor Corporation www.fairchildsemi.com
6N13XM, HCPLXXXM Rev. 1.0.1 2
Single-Channel: 6N135M, 6N136M, HCPL2503M, HCPL4502M, HCPL4503M
Dual-Channel: HCPL2530M, HCPL2531M — High Speed Transistor Optocouplers
PRELIMINARY
Absolute Maximum Ratings
(T
A
= 25°C unless otherwise specified)
Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be
operable above the recommended operating conditions and stressing the parts to these levels is not recommended.
In addition, extended exposure to stresses above the recommended operating conditions may affect device reliability.
The absolute maximum ratings are stress ratings only.
Notes:
1. Derate linearly above 70°C free-air temperature at a rate of 0.8mA/°C.
2. Derate linearly above 70°C free-air temperature at a rate of 1.6mA/°C.
3. Derate linearly above 70°C free-air temperature at a rate of 0.9 mW/°C.
4. Derate linearly above 70°C free-air temperature at a rate of 2.0 mW/°C.
Symbol Parameter Condition Value Units
T
STG
Storage Temperature -40 to +125 °C
T
OPR
Operating Temperature -40 to +100 °C
T
SOL
Lead Solder Temperature
(Wave)
260 for 10 sec °C
EMITTER
I
F
(avg) DC/Average Forward Input
Current Each Channel
(1)
25 mA
I
F
(pk) Peak Forward Input Current
Each Channel
(2)
50% duty cycle, 1ms P.W. 50 mA
I
F
(trans) Peak Transient Input Current
Each Channel
≤
1µs P.W., 300pps 1.0 A
V
R
Reverse Input Voltage Each
Channel
5V
P
D
Input Power Dissipation Each
Channel
6N135M, 6N136M, HCPL2503M,
HCPL4502M, HCPL4503M
100 mW
HCPL2530M, HCPL2531M
(3)
45
DETECTOR
I
O
(avg) Average Output Current Each
Channel
8 mA
I
O
(pk) Peak Output Current Each
Channel
16 mA
V
EBR
Emitter-Base Reverse Voltage 6N135M, 6N136M and HCPL2503M only 5 V
V
CC
Supply Voltage -0.5 to 30 V
V
O
Output Voltage -0.5 to 20 V
I
B
Base Current 6N135M, 6N136M and HCPL2503M only 5 mA
PD Output Power Dissipation
Each Channel
6N135M, 6N136M, HCPL2503M,
HCPL4502M, HCPL4503M
(4)
100 mW
HCPL2530M, HCPL2531M 35 mW
©2008 Fairchild Semiconductor Corporation www.fairchildsemi.com
6N13XM, HCPLXXXM Rev. 1.0.1 3
Single-Channel: 6N135M, 6N136M, HCPL2503M, HCPL4502M, HCPL4503M
Dual-Channel: HCPL2530M, HCPL2531M — High Speed Transistor Optocouplers
PRELIMINARY
Electrical Characteristics
(T
A
= 0 to 70°C Unless otherwise specified)
Individual Component Characteristics
*All Typicals at T
A
= 25°C
Symbol Parameter Test Conditions Device Min. Typ.* Max. Unit
EMITTER
V
F
Input Forward Voltage I
F
= 16mA, T
A
=25°C All 1.45 1.7 V
I
F
= 16mA All 1.8
B
VR
Input Reverse
Breakdown Voltage
I
R
= 10 µA All 5.0 V
∆
V
F
/
∆
T
A
Temperature Coefficient
of Forward Voltage
I
F
= 16mA All -1.6 mV/°C
DETECTOR
I
OH
Logic High Output
Current
I
F
= 0mA, V
O
= V
CC
= 5.5V,
T
A
=25°C
All 0.003 0.5 µA
I
F
= 0mA, V
O
= V
CC
= 15V,
T
A
=25°C
6N135M
6N136M
HCPL4502M
HCPL4503M
HCPL2503M
0.005 1
I
F
= 0mA, V
O
= V
CC
= 15V All 50
I
CCL
Logic Low Supply
Current
I
F
= 16mA, V
O
= Open,
V
CC
= 15V
6N135M
6N136M
HCPL4502M
HCPL4503M
HCPL2503M
145 200 µA
I
F1
= I
F2
= 16mA,
V
O
= Open, V
CC
= 15V
HCPL2530M
HCPL2531M
250 400
I
CCH
Logic High Supply
Current
I
F
= 0mA, V
O
= Open,
V
CC
= 15V, T
A
=25°C
6N135M
6N136M
HCPL4502M
HCPL4503M
HCPL2503M
1µA
I
F
= 0mA, V
O
= Open,
V
CC
= 15V
6N135M
6N136M
HCPL4502M
HCPL4503M
HCPL2503M
2
I
F
= 0mA, V
O
= Open,
V
CC
= 15V
HCPL2530M
HCPL2531M
0.02 4
©2008 Fairchild Semiconductor Corporation www.fairchildsemi.com
6N13XM, HCPLXXXM Rev. 1.0.1 4
Single-Channel: 6N135M, 6N136M, HCPL2503M, HCPL4502M, HCPL4503M
Dual-Channel: HCPL2530M, HCPL2531M — High Speed Transistor Optocouplers
PRELIMINARY
Electrical Characteristics
(Continued) (T
A
= 0 to 70°C unless otherwise specified)
Transfer Characteristics
*All Typicals at T
A
= 25°C
Note:
5. Current Transfer Ratio is defined as a ratio of output collector current, I
O
, to the forward LED input current, I
F
,
times 100%.
Symbol Parameter Test Conditions Device Min. Typ.* Max. Unit
COUPLED
CTR Current Transfer
Ratio
(5)
I
F
= 16mA, V
O
= 0.4 V,
V
CC
= 4.5V, T
A
=25°C
6N135M
HCPL2530M
71850%
6N136M
HCPL4502M
HCPL4503M
HCPL2531M
19 30 50 %
HCPL2503M 12 27 %
I
F
= 16mA,
V
CC
= 4.5V
V
OL
= 0.4V 6N135M 5 21 %
V
OL
= 0.5V HCPL2530M
V
OL
= 0.4V 6N136M
HCPL4502M
HCPL4503M
15 30 %
V
OL
= 0.5V HCPL2531M
V
OL
= 0.4V HCPL2503M 9 30 %
V
OL
Logic LOW Output
Voltage
I
F
= 16mA, I
O
= 1.1mA,
V
CC
= 4.5V, T
A
=25°C
6N135M 0.10 0.4 V
HCPL2530M 0.10 0.5
I
F
= 16mA, I
O
= 3mA,
V
CC
= 4.5V, T
A
=25°C
6N136M
HCPL2503M
HCPL4503M
0.15 0.4
HCPL2531M 0.15 0.5
I
F
= 16mA, I
O
= 0.8mA,
V
CC
= 4.5V
6N135M
HCPL2530M
0.5
I
F
= 16mA, I
O
= 2.4mA,
V
CC
= 4.5V
HCPL4502M
HCPL4503M
HCPL2531M
0.5
©2008 Fairchild Semiconductor Corporation www.fairchildsemi.com
6N13XM, HCPLXXXM Rev. 1.0.1 5
Single-Channel: 6N135M, 6N136M, HCPL2503M, HCPL4502M, HCPL4503M
Dual-Channel: HCPL2530M, HCPL2531M — High Speed Transistor Optocouplers
PRELIMINARY
Electrical Characteristics (Continued) (TA = 0 to 70°C unless otherwise specified)
Switching Characteristics (VCC = 5V)
** All Typicals at TA = 25°C
Notes:
6. The 4.1kΩ load represents 1 LSTTL unit load of 0.36mA and 6.1kΩ pull-up resistor.
7. The 1.9kΩ load represents 1 TTL unit load of 1.6mA and 5.6kΩ pull-up resistor.
8. Common mode transient immunity in logic high level is the maximum tolerable (positive) dVcm/dt on the leading edge
of the common mode pulse signal VCM, to assure that the output will remain in a logic high state (i.e., VO > 2.0V).
Common mode transient immunity in logic low level is the maximum tolerable (negative) dVcm/dt on the trailing edge
of the common mode pulse signal, VCM, to assure that the output will remain in a logic low state (i.e., VO < 0.8V).
Symbol Parameter Test Conditions Device Min. Typ.* Max. Unit
TPHL Propagation Delay
Time to Logic LOW
TA = 25°C, RL = 4.1kΩ,
IF = 16mA(6) (Fig. 7)
6N135M
HCPL2530M
0.45 1.5 µs
RL = 1.9kΩ, IF = 16mA,
TA = 25°C(7) (Fig. 7)
6N136M
HCPL4502M
HCPL4503M
HCPL2503M
HCPL2531M
0.45 0.8 µs
RL = 4.1kΩ, IF = 16mA(6) (Fig. 7) 6N135M
HCPL2530M
2.0 µs
RL = 1.9kΩ, IF = 16mA(7) (Fig. 7) 6N136M
HCPL4502M
HCPL4503M
HCPL2503M
HCPL2531M
1.0 µs
TPLH Propagation Delay
Time to Logic HIGH
TA = 25°C, (RL = 4.1kΩ,
IF = 16mA(6) (Fig. 7)
6N135M
HCPL2530M
0.5 1.5 µs
RL = 1.9kΩ, IF = 16mA(7) (Fig. 7)
TA = 25°C
6N136M
HCPL4502M
HCPL4503M
HCPL2503M
HCPL2531M
0.3 0.8 µs
RL = 4.1kΩ, IF = 16mA(6) (Fig. 7) 6N135M
HCPL2530M
2.0 µs
RL = 1.9kΩ, IF = 16mA(7) (Fig. 7) 6N136M
HCPL4502M
HCPL4503M
HCPL2503M
HCPL2531M
1.0 µs
|CMH| Common Mode
Transient
Immunity at
Logic High
IF = 0mA, VCM = 10VP-P,
RL = 4.1kΩ, TA = 25°C(8) (Fig. 8)
6N135M
HCPL2530M
10,000 V/µs
IF = 0mA, VCM = 10VP-P,
RL = 1.9kΩ, TA = 25°C(8) (Fig. 8)
6N136M
HCPL4502M
HCPL2503M
HCPL2531M
10,000 V/µs
IF = 0mA, VCM = 1,500VP-P,
RL = 1.9kΩ, TA = 25°C(8) (Fig. 8) HCPL4503M 15,000 30,000
|CML| Common Mode
Transient
Immunity at
Logic Low
IF = 16mA, VCM = 10VP-P,
RL = 4.1kΩ, TA = 25°C(8) (Fig. 8)
6N135M
HCPL2530M
10,000 V/µs
IF = 16mA, VCM = 10VP-P,
RL = 1.9kΩ(8) (Fig. 8)
6N136M
HCPL4502M
HCPL2503M
HCPL2531M
10,000 V/µs
IF = 0mA, VCM = 1,500VP-P,
RL = 1.9kΩ, TA = 25°C(8) (Fig. 8) HCPL4503M 15,000 30,000
©2008 Fairchild Semiconductor Corporation www.fairchildsemi.com
6N13XM, HCPLXXXM Rev. 1.0.1 6
Single-Channel: 6N135M, 6N136M, HCPL2503M, HCPL4502M, HCPL4503M
Dual-Channel: HCPL2530M, HCPL2531M — High Speed Transistor Optocouplers
PRELIMINARY
Electrical Characteristics (Continued) (TA = 0 to 70°C unless otherwise specified)
Isolation Characteristics (TA = 0 to 70°C Unless otherwise specified)
Notes:
9. Device is considered a two terminal device: Pins 1, 2, 3 and 4 are shorted together and Pins 5, 6, 7 and 8 are
shorted together.
10. Measured between pins 1 and 2 shorted together, and pins 3 and 4 shorted together.
11. 5,000Vrms for 1 minute duration is equivalent to 6,000Vrms for 1 second duration.
Symbol Characteristics Test Conditions Min Typ** Max Unit
VISO Withstand Insulation Test
Voltage
RH ≤ 50%, TA = 25°C, II-O ≤ 10µA,
t = 1 min., f = 50Hz(9)(11) 5,000 VRMS
RI-O Resistance (Input to Output) VI-O = 500VDC(9) 1011 Ω
CI-O Capacitance (Input to Output) f = 1MHz, VI-O = 0V(9) 1pF
HFE DC Current Gain IO = 3mA, VO = 5V(9) 150
II-I Input-Input Insulation
Leakage Current
RH ≤ 45%, VI-I = 500VDC(10)
t = 5 s, (HCPL2530M/2531M only)
0.005 µA
RI-I Input-Input Resistance VI-I = 500 VDC(10)
(HCPL2530M/2531M only)
1011 Ω
CI-I Input-Input Capacitance f = 1MHz(10)
(HCPL2530M/2531M only)
0.03 pF
©2008 Fairchild Semiconductor Corporation www.fairchildsemi.com
6N13XM, HCPLXXXM Rev. 1.0.1 7
Single-Channel: 6N135M, 6N136M, HCPL2503M, HCPL4502M, HCPL4503M
Dual-Channel: HCPL2530M, HCPL2531M — High Speed Transistor Optocouplers
PRELIMINARY
Typical Performance Curves
Fig. 1 Normalized CTR vs. Forward Current
IF - FORWARD CURRENT (mA)
0.1 1 10 100
NORMALIZED CTR
0.0
0.2
0.4
0.6
0.8
1.0
1.2
Fig. 2 Normalized CTR vs. Temperature
TA - TEMPERATURE (°C)
-40 -20 0 20 40 60 80 100
NORMALIZED CTR
0.0
0.2
0.4
0.6
0.8
1.0
1.2
Fig. 3 Output Current vs. Output Voltage
VO – OUTPUT VOLTAGE (V)
02468101214161820
I
O
– OUTPUT CURRENT (mA)
18
16
14
12
10
8
6
4
2
0
Normalized to:
IF = 16 mA
VO = 0.4 V
VCC = 5 V
TA = 25°C
Normalized to:
TA = 25°C
IF = 16mA
VCC = 4.5V
VO = 0.4V
Fig. 4 Logic High Output Current
vs. Temperature
TA – TEMPERATURE (°C)
-40 -20 0 20 40 60 80 100
I
OH
– LOGIC HIGH OUTPUT CURRENT (nA)
0.1
1
10
100
Fig. 5 Propagation Delay vs. Temperature
TA – TEMPERATURE (°C)
-40 -20 0 20 40 60 80 100
Tp – PROPAGATION DELAY (ns)
0
100
200
300
400
500
600
700
800
RL = 1.9kΩ (tPHL)R = 4.1kΩ (tPHL)
L
RL = 1.9kΩ (tPLH)
RL
= 4.1kΩ (tPLH)
Fig. 6 Propagation Delay vs. Load Resistance
RL – LOAD RESISTANCE (kΩ)
1 10
T
P
- PROPAGATION DELAY (ns)
100
1000
IF = 16mA (tPLH)
IF = 10mA (tPHL)
IF = 10mA (tPLH)IF = 16mA (tPHL)
TA = 25°C
VCC = 5 V IF = 0 mA
VCC = 5.5V
VO = 5.5V
Frequency = 10kHz
Duty Cycle = 10%
IF = 16mA
VCC = 5 V
IF
35mA
30mA
25mA
20mA
15mA
10mA
5mA
= 40mA
Frequency = 10kHz
Duty Cycle = 10%
IF = 16mA
VCC = 5 V
©2008 Fairchild Semiconductor Corporation www.fairchildsemi.com
6N13XM, HCPLXXXM Rev. 1.0.1 8
Single-Channel: 6N135M, 6N136M, HCPL2503M, HCPL4502M, HCPL4503M
Dual-Channel: HCPL2530M, HCPL2531M — High Speed Transistor Optocouplers
PRELIMINARY
Test Circuits
Pulse Gen
CM
V
V
FF
B
A
+-
+5 V
O
V
-
I
F
3
4
+
F
V
-
2
1
Shield
Noise
6
O
5
GND
7
8
V
B
V
CC
V
L
R
PLH
OL
V
V
O
0
5 V
1.5 V
F
I
1.5 V
T
PHL
T
Switch at A : I = 0 mA
F
Switch at A : I = 16 mA
F
t
r
V
O
O
V
OL
V
5 V
0 V 10% 10%
90%
CM
V 10 V
4 5
Noise
1
2
3
Shield
8
7
6
+5 V
O
V
V
CC
V
01
V
02
GND
V
F1
-
+
F2
V
-
F
I+
10% DUTY CYCLE
I/f < 100µS
F
I
MONITOR
L
R
C = 1.5 µF
L
Pulse
Generator
tr = 5ns
Z = 50
O
Ω
GND
+
4 5
1
3
2
-
F2
V
V
F1
-
Shield
Noise
+5 V
CC
8
V
L
V
6
02
V
7
R
01
V
O
V
CM
A
B
Pulse Gen
F
I
+-
+
3
I Monitor
F
4
I/f < 100µs
10% D.C.
tr = 5ns
Generator
Pulse
Z = 50
O
+
V
F
I
Ω
F
-
2
1
Shield
Noise
V
O
O
6
5
GND
7
8
V
B
V
L
R
CC
V+5 V
0.1 µF
L
C = 1.5 µF
Test Circuit for 6N135M, 6N136M, HCPL2503M, HCPL4502M and HCPL4503M
Test Circuit for HCPL2530M and HCPL2531M
0.1 µF
f
t
0.1 µF
0.1 µF
FF
V
m
R
m
R
90%
Fig. 7 Switching Time Test Circuit
Fig. 8 Common Mode Immunity Test Circuit
Test Circuit for 6N135M, 6N136M, HCPL2503M, HCPL4502M and HCPL4503M Test Circuit for HCPL2530M and HCPL2531M
©2008 Fairchild Semiconductor Corporation www.fairchildsemi.com
6N13XM, HCPLXXXM Rev. 1.0.1 9
Single-Channel: 6N135M, 6N136M, HCPL2503M, HCPL4502M, HCPL4503M
Dual-Channel: HCPL2530M, HCPL2531M — High Speed Transistor Optocouplers
PRELIMINARY
Package Dimensions
Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner
without notice. Please note the revision and/or date on the drawing and contact a Fairchild Semiconductor representative to verify or
obtain the most recent revision. Package specifications do not expand the terms of Fairchild’s worldwide terms and conditions,
specifically the warranty therein, which covers Fairchild products.
Always visit Fairchild Semiconductor’s online packaging area for the most recent package drawings:
http://www.fairchildsemi.com/packaging/
Through Hole
Surface Mount
Note:
All dimensions are in inches (millimeters)
0.4" Lead Spacing
8-Pin DIP – Land Pattern (option S)
0.200 (5.08)
0.140 (3.55)
0.100 (2.54) TYP
0.022 (0.56)
0.016 (0.41)
0.020 (0.51) MIN
0.390 (9.91)
0.370 (9.40)
0.270 (6.86)
0.250 (6.35)
3
0.070 (1.78)
0.045 (1.14)
241
56 78
0.300 (7.62)
TYP
0.154 (3.90)
0.120 (3.05)
0.016 (0.40)
0.008 (0.20)
15° MAX
PIN 1
ID.
SEATING PLANE
Lead Coplanarity : 0.004 (0.10) MAX
0.270 (6.86)
0.250 (6.35)
0.390 (9.91)
0.370 (9.40)
0.022 (0.56)
0.016 (0.41)
0.100 (2.54)
TYP
0.020 (0.51)
MIN
0.070 (1.78)
0.045 (1.14)
0.300 (7.62)
TYP
0.405 (10.30)
MAX.
0.315 (8.00)
MIN
0.045 [1.14]
32 14
5678
0.016 (0.41)
0.008 (0.20)
PIN 1
ID.
0.200 (5.08)
0.140 (3.55)
0.100 (2.54) TYP
0.022 (0.56)
0.016 (0.41)
0.004 (0.10) MIN
0.390 (9.91)
0.370 (9.40)
0.270 (6.86)
0.250 (6.35)
3
0.070 (1.78)
0.045 (1.14)
241
56 78
0.400 (10.16)
TYP
0.154 (3.90)
0.120 (3.05)
0.016 (0.40)
0.008 (0.20)
0° to 15°
PIN 1
ID.
SEATING PLANE
0.070 (1.78)
0.060 (1.52)
0.030 (0.76)
0.100 (2.54)
0.295 (7.49)
0.415 (10.54)
©2008 Fairchild Semiconductor Corporation www.fairchildsemi.com
6N13XM, HCPLXXXM Rev. 1.0.1 10
Single-Channel: 6N135M, 6N136M, HCPL2503M, HCPL4502M, HCPL4503M
Dual-Channel: HCPL2530M, HCPL2531M — High Speed Transistor Optocouplers
PRELIMINARY
Ordering Information
Marking Information
Option Example Part Number Description
No option 6N135M Standard through hole lead form
S 6N135SM Surface mount lead bend
SD 6N135SDM Surface mount; tape and reel
T 6N135TM 0.4" lead spacing
V 6N135VM IEC60747-5-2 (approval pending)
TV 6N135TVM IEC60747-5-2 (approval pending); 0.4" lead spacing
SV 6N135SVM IEC60747-5-2 (approval pending); surface mount
SDV 6N135SDVM IEC60747-5-2 (approval pending); surface mount;
tape and reel
1
2
6
43 5
Definitions
1Fairchild logo
2Device number
3IEC60747-5-2 mark (Note: Only appears on parts ordered with this
option – See order entry table)
4Two digit year code, e.g., ‘08’
5Two digit work week ranging from ‘01’ to ‘53’
6 Assembly package code
2503
BYY
XXV
©2008 Fairchild Semiconductor Corporation www.fairchildsemi.com
6N13XM, HCPLXXXM Rev. 1.0.1 11
Single-Channel: 6N135M, 6N136M, HCPL2503M, HCPL4502M, HCPL4503M
Dual-Channel: HCPL2530M, HCPL2531M — High Speed Transistor Optocouplers
PRELIMINARY
Carrier Tape Specifications
Symbol Description Dimension in mm
WTape Width 16.0 ± 0.3
tTape Thickness 0.30 ± 0.05
P0Sprocket Hole Pitch 4.0 ± 0.1
D0Sprocket Hole Diameter 1.55 ± 0.05
E Sprocket Hole Location 1.75 ± 0.10
FPocket Location 7.5 ± 0.1
P22.0 ± 0.1
PPocket Pitch 12.0 ± 0.1
A0Pocket Dimensions 10.30 ±0.20
B010.30 ±0.20
K04.90 ±0.20
W1Cover Tape Width 13.2 ± 0.2
dCover Tape Thickness 0.1 max
Max. Component Rotation or Tilt 10°
R Min. Bending Radius 30
d
0
P
t2
D0
1
1
W
User Direction of Feed
0
K
B0
A0W
E
D
F
P
P
©2008 Fairchild Semiconductor Corporation www.fairchildsemi.com
6N13XM, HCPLXXXM Rev. 1.0.1 12
Single-Channel: 6N135M, 6N136M, HCPL2503M, HCPL4502M, HCPL4503M
Dual-Channel: HCPL2530M, HCPL2531M — High Speed Transistor Optocouplers
PRELIMINARY
Reflow Profile
• Peak reflow temperature: 260 C (package surface temperature)
• Time of temperature higher than 183 C for 160 seconds or less
• One time soldering reflow is recommended
245 C, 10–30 s
Time (Minute)
0
300
250
200
150
100
50
00.5 1 1.5 2 2.5 3 3.5 4 4.5
Temperature (°C)
Time above 183 C, <160 sec
Ramp up = 2–10 C/sec
260 C peak
©2008 Fairchild Semiconductor Corporation www.fairchildsemi.com
6N13XM, HCPLXXXM Rev. 1.0.1 13
TRADEMARKS
The following includes registered and unregistered trademarks and service marks, owned by Fairchild Semiconductor and/or its global subsidiaries,andis not
intended to be an exhaustive list of all such trademarks.
Build it Now™
CorePLUS™
CorePOWER™
CROSSVOLT™
CTL™
Current Transfer Logic™
EcoSPARK®
EfficentMax™
EZSWITCH™ *
™
®
Fairchild®
Fairchild Semiconductor®
FACT Quiet Series™
FACT®
FAST®
FastvCore™
FlashWriter®*
FPS™
F-PFS™
FRFET®
Global Power ResourceSM
Green FPS™
Green FPS™e-Series™
GTO™
IntelliMAX™
ISOPLANAR™
MegaBuck™
MICROCOUPLER™
MicroFET™
MicroPak™
MillerDrive™
MotionMax™
Motion-SPM™
OPTOLOGIC®
OPTOPLANAR®
®
PDP SPM™
Power-SPM™
PowerTrench®
Programmable Active Droop™
QFET®
QS™
Quiet Series™
RapidConfigure™
™
Saving our world, 1mW/W/kW at a time™
SmartMax™
SMART START™
SPM®
STEALTH™
SuperFET™
SuperSOT™-3
SuperSOT™-6
SuperSOT™-8
SupreMOS™
SyncFET™
®
ThePower Franchise®
TinyBoost™
TinyBuck™
TinyLogic®
TINYOPTO™
TinyPower™
TinyPWM™
TinyWire™
µSerDes™
UHC®
Ultra FRFET™
UniFET™
VCX™
VisualMax™
*EZSWITCH™ and FlashWriter®are trademarks of System General Corporation, used under license by Fairchild Semiconductor.
DISCLAIMER
FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE
RELIABILITY, FUNCTION, OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR
CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. THESE
SPECIFICATIONS DO NOT EXPAND THE TERMS OF FAIRCHILD’S WORLDWIDE TERMS AND CONDITIONS, SPECIFICALLY THE WARRANTY THEREIN,
WHICH COVERS THESE PRODUCTS.
LIFE SUPPORT POLICY
FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE
EXPRESS WRITTEN APPROVAL OF FAIRCHILD SEMICONDUCTOR CORPORATION.
As used herein:
1. Life support devices or systems are devices or systems which, (a) are
intended for surgical implant into the body or (b) support or sustain life,
and (c) whose failure to perform when properly used in accordance
with instructions for use provided in the labeling, can be reasonably
expected to result in a significant injury of the user.
2. A critical component in any component of a life support, device, or
system whose failure to perform can be reasonably expected to
cause the failure of the life support device or system, or to affect its
safety or effectiveness.
ANTI-COUNTERFEITING POLICY
Fairchild Semiconductor Corporation's Anti-Counterfeiting Policy. Fairchild's Anti-Counterfeiting Policy is also stated on our external website, www.fairchildsemi.com,
under Sales Support.
Counterfeiting of semiconductor parts is a growing problem in the industry. All manufacturers of semiconductor products are experiencing counterfeiting of their parts.
Customers who inadvertently purchase counterfeit parts experience many problems such as loss of brand reputation, substandard performance, failedapplications,
and increased cost of production and manufacturing delays. Fairchild is taking strong measures to protect ourselves and our customers from the proliferation of
counterfeit parts. Fairchild strongly encourages customers to purchase Fairchild parts either directly from Fairchild or from Authorized Fairchild Distributors who are
listed by country on our web page cited above. Products customers buy either from Fairchild directly or from Authorized Fairchild Distributors are genuine parts, have
full traceability, meet Fairchild's quality standards for handling and storage and provide access to Fairchild's full range of up-to-date technicalandproduct information.
Fairchild and our Authorized Distributors will stand behind all warranties and will appropriately address any warranty issues that may arise. Fairchild will not provide
any warranty coverage or other assistance for parts bought from Unauthorized Sources. Fairchild is committed to combat this global problem and encourage our
customers to do their part in stopping this practice by buying direct or from authorized distributors.
PRODUCT STATUS DEFINITIONS
Definition of Terms
Datasheet Identification Product Status Definition
Advance Information Formative / In Design Datasheet contains the design specifications for product development. Specifications may change in
any manner without notice.
Preliminary Datasheet contains preliminary data; supplementary data will be published at a later date. Fairchild
Semiconductor reserves the right to make changes at any time without notice to improve design.
No Identification Needed Ful
First Production
lProduction Datasheet contains final specifications. Fairchild Semiconductor reserves the right to make changes
at any time without notice to improve the design.
Obsolete Not In Production Datasheet contains specifications on a product that is discontinued by Fairchild Semiconductor. The
datasheet is for reference information only.
Rev. I36
Single-Channel: 6N135M, 6N136M, HCPL2503M, HCPL4502M, HCPL4503M
Dual-Channel: HCPL2530M, HCPL2531M — High Speed Transistor Optocouplers
PRELIMINARY