LCR-8105G - GW INSTEK - Product.Network

Education Lab and Training Institution

Research & Design

Quality Assurance Verification

Full Measuring Functions with DUT V/I

Monitor

Wide Test Frequency 20Hz~10/5/1MHz

0.1% Basic Accuracy & 6 Digits

Measurement Resolution

Large LCD Display with Intuitive User

Interface

DC Resistance Measurement

Multi Step Mode

Graph Mode

Standard RS-232C / GPIB Interface

FEATURES

APPLICATIONS

Made to Measure Since 1975

LCR-8000G Series

10MHz / 5MHz / 1MHz PRECISION LCR METER

The Smarter Way to Characterize Components

The LCR-8000G Series LCR meter, with test frequency up to 10MHz, provides accuracy, versatility and high

resolution for a wide range of component measurements, even including DC resistance measurement and

Voltage/Current monitoring. The Multi-Step function allows on-screen programming of customized

measurement sequence with Pass/Fail indication. Each program includes 30 test steps and each test step can be

set with selected parameters and test limits. Under Multi-Step operation, a tedious work routine can be done

step by step automatically just at a press of a button. With Graph Mode, LCR-8110G, LCR-8105G and LCR-8101G

display the component impedance response either over a wide range of test frequency sweep or over a wide

range of test voltage sweep in a graph chart. This gives an analysis result of either impedance vs. frequency or

impedance vs. applied voltage all at a glance. GPIB and RS-232C interfaces are available as standard for

instrument control and test result display on the PC. The rich features of LCR-8000G Series easily make your

measurement tasks done at a very competitive price.

Pass/fail Function With Judgment Alarm

In the Pass/Fail test, primary parameter measurement

result is compared with user-defined limits and the

pass or fail result is then displayed. Three methods,

including absolute limit, percentage and delta limit,

are available for Hi(high) and Lo(low) limit setting

based on the nominal test value. The Pass/Fail test

checks whether the parameter measurement result

sits within the limits, then display "PASS" for within

the limits, or "LO" for lower than the low limit, or

"HI" For higher than the high limit. A scale and bar

for displaying measurement result is shown at the

center of the screen to give a graphical identification,

which greatly reduces operator's load in a long time

inspection work. This scale and bar also facilitate the

adjustment of the variable components. Either Pass

or Fail result can be set with a buzzer alarm, which

makes component or material sorting easy with

sound identification.

Wide Frequency Range With Friendly

Intuitive User Interface

The LCR-8000G Series is designed to perform precision

impedance measurements over a wide frequency range

of 20Hz ~ 10MHz for LCR-8110G, 20Hz ~ 5MHz for

LCR-8105G and 20Hz ~1MHz for LCR-8101G. The

instrument is capable of measuring 11 different

parameters with 0.1% basic accuracy, which meets the

precision measurement requirements of components

and modules used in the RF circuits. The large LCD

display with single-layer operation menu of LCR-8000G

Series provides users with ultimate convenience to

plug and play without much learning time.

The graph function shows the component

characteristics in visual manner. Either voltage sweep

or frequency sweep can be selected for horizontal

scale. Just select the parameter, and set the start/stop

voltage or the start/stop frequency of the sweep, LCR

-8000G will run through the sequence of

measurements and show the results on a graph.

This graphical parameter measurement performs the

characteristic verification of components and

materials over the response to the changes in AC test

frequency or AC test voltage without the need of

complex programming of an external controller. When

the graph gets out of the vertical range, the LCR-

8000G Series can automatically adjust the scale to

get full test information. On the graph the marker

operation is available for detailed observation.

Graph Mode

The Multi-Step mode is capable of running a series of

measurements of a component at a number of user-

defined steps in sequence automatically. Total 64

programs can be saved into the non-volatile memory,

and each program contains up to 30 test steps. The

parameter and Hi/Lo limits can be set respectively for

each test step. After a program being properly edited,

the instrument can run through all the measurement

steps either at a press of the button under the Manual

Trigger selection, or automatically run the program by

detecting the connection of a DUT under the Auto

Trigger selection. When all the test steps are

completed, the screen shows the measurement

reading of the parameter being selected for each step

with Pass, HI, or LO measurement result.

Multi Step Mode

PASS/FAIL Function ( abs , % , )

with Judgment Alarm

Average 1 ~ 256 Times

CR-8000GGD1DH

ORDERING INFORMATION

Specifications subject to change without notice.

LCR-8110G 10 MHz Precision LCR Meter

LCR-8105G 5 MHz Precision LCR Meter

LCR-8101G 1 MHz Precision LCR Meter

STANDARD ACCESSORIES

User manual x 1

Power cord x 1

Test lead LCR-12 x 1

OPTIONAL ACCESSORIES SELECTION GUIDE

Brief Description

Accessory Model LCR-8110G LCR-8105G LCR-8101G

LCR-05

LCR-06A

LCR-07

LCR-08

LCR-09

LCR-13

LCR-12

GTL-232

GRA-404

Test Fixture for axial & radial lead components

Test Lead with Kelvin clip (4 wire type)

Test Lead with Alligator clip (2 wire type)

Test Lead with Kelvin clip (4 wire type)

Test Fixture (Tweezers) for SMD/Chip components

Test Fixture for SMD/Chip components

RS-232C Cable

Rack Adapter Panel (19", 4U)

Note " " means the accessories work with a frequency limitation (under 1MHz)

LCR-06ALCR-05 LCR-07 LCR-08 LCR-09 LCR-13 LCR-12

Test Signal Level (rms)Test Frequency Step Accuracy

10mV ~ 2V3MHz 1mV/10mV 2% 5mV

10mV ~ 1V> 3MHz 1mV/10mV 2% 5mV

R, Z, X, Rdc

Mode

G, Y, B

0.1m ~ 100M

Measure Range

10nS ~ 1000S

0.1nH ~ 100kH

0.01pF ~ 1F

0.00001 ~ 9.9999

0.1 ~ 9999.9

-180 ~ +180

TEST FREQUENCY

INPUT IMPEDANCE

BASIC ACCURACY

TEST SPEED

TEST SIGNAL LEVELS

SHORT CIRCUIT CURRENT

MEASUREMENT RANGES

MEASUREMENT PARAMETERS

SERIES OR PARALLEL EQUIVALENT CIRCUIT

SERIES EQUIVALENT CIRCUIT ONLY

PARALLEL EQUIVALENT CIRCUIT ONLY

POLAR FORM

LCD DISPLAY

INTERFACE

POWER SOURCE

DIMENSIONS & WEIGHT

20Hz ~ 1MHz/5MHz/10MHz, 5 Digits, 0.005%

100

0.1% (R, Z, X, G, Y, B, L, C)

AC (>2kHz)

MAX: 75mS

FAST: 150mS

MEDIUM: 450mS

SLOW: 600mS

MAX: 30mS

FAST: 60mS

MEDIUM: 120mS

SLOW: 900mS

Max. 20mA

Impedance (Z), Phase Angle ( ), Inductance (L), Capacitance (C), AC Resistance (Rac), Quality Factor (Q),

Dissipation Factor (D), Admittance (Y), Conductance (G), Reactance (X), Susceptance (B), DC Resistance (Rdc)

C + R, C + D, C + Q, L + R, L + Q, L + D

X + R, X + D, X + Q

C + G, B + G, B + D, B + Q, B + R, L + G

Z + Phase Angle, Y + Phase Angle

320 x 240 DOT-MATRIX

RS-232C, GPIB

330(W) x 170(H) x 340(D)mm, Approx. 5kg

SPECIFICATIONS

AC 115V (+10%/-25%), AC 230V (+15% / -14%)(Selectable), 50/60Hz

AVERAGE 1 ~ 256 times

GOOD WILL INSTRUMENT CO., LTD.

Global Headquarters

No. 7-1, Jhongsing Road, Tucheng City, Taipei County 236, Taiwan

T +886-2-2268-0389 F +886-2-2268-0639

E-mail: marketing@goodwill.com.tw

China Subsidiary

E-mail: marketing@instek.com.cn

U.S.A. Subsidiary

INSTEK AMERICA CORP.

3661 Walnut Avenue Chino, CA 91710, U.S.A.

T +1-909-5918358 F +1-909-5912280

E-mail: sales@instekamerica.com

Japan Subsidiary

INSTEK JAPAN CORPORATION

4F, Prosper Bldg, 1-3-3 Iwamoto-Cho Chiyoda-Ku,

Tokyo 101-0032 Japan

T +81-3-5823-5656 F +81-3-5823-5655

E-mail: info@instek.co.jp

GOOD WILL INSTRUMENT (SUHZOU) CO., LTD.

NO. 69, Lushan Road, Snd, Suzhou Jiangsu 215011 China

T +86-512-6661-7177 F +86-512-6661-7277

Malaysia Subsidiary

27, Persiaran Mahsuri 1/1, Sunway Tunas,

11900 Bayan Lepas, Penang, Malaysia

T +604-6309988 F +604-6309989

E-mail: sales@goodwill.com.my

GOOD WILL INSTRUMENT (M) SDN. BHD.

Korea Subsidiary

Room No.805, Ace Hightech-City B/D 1Dong,

Mullae-Dong 3Ga 55-20, Yeongduengpo-Gu, Seoul, Korea

T +82 2 3439 2205 F +82 2 3439 2207

E-mail : gwinstek@gwinstek.co.kr

GOOD WILL INSTRUMENT KOREA CO., LTD.

www.gwinstek.com

Since 1975

Made to Measure

Simply Reliable

Our low TCO helps you control costs

with reliable products and services.