Data Sheet, Rev. 4.0, April 2008
TLE6250
High Speed CAN-Transceiver
Automotive Power
Edition 2008-04-28
Published by
Infineon Technologies AG
81726 Munich, Germany
© 2004 Infineon Technologies AG
All Rights Reserved.
Legal Disclaimer
The information given in this document shall in no event be regarded as a guarantee of conditions or
characteristics. With respect to any examples or hints given herein, any typical values stated herein and/or any
information regarding the application of the device, Infineon Technologies hereby disclaims any and all warranties
and liabilities of any kind, including without limitation, warranties of non-infringement of intellectual property rights
of any third party.
Information
For further information on technology, delivery terms and conditions and prices, please contact the nearest
Infineon Technologies Office (www.infineon.com).
Warnings
Due to technical requirements, components may contain dangerous substances. For information on the types in
question, please contact the nearest Infineon Technologies Office.
Infineon Technologies components may be used in life-support devices or systems only with the express written
approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure
of that life-support device or system or to affect the safety or effectiveness of that device or system. Life support
devices or systems are intended to be implanted in the human body or to support and/or maintain and sustain
and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may
be endangered.
Type Package
TLE6250G PG-DSO-8
TLE6250C (chip)
TLE6250GV33 PG-DSO-8
TLE6250CV33 (chip)
High Speed CAN-Transceiver
TLE6250
Data Sheet 3 Rev. 4.0, 2008-04-28
Features
• CAN data transmission rate up to 1 MBaud
• Receive-only Mode and Stand-by Mode
• Suitable for 12 V and 24 V applications
• Excellent EMC performance (very high immunity and
very low emission)
• Version for 5 V and 3.3 V microcontrollers
• Bus pins are short circuit proof to ground and battery
voltage
• Overtemperature protection
• Very wide temperature range (-40 °C up to 150 °C)
• Green Product (RoHS compliant)
• AEC Qualified
Description
The HS CAN-transceiver family TLE6250 (TLE6250G and TLE6250GV33) are
monolithic integrated circuits that are available as bare die as well as in a PG-DSO-8
package. The ICs are optimized for high speed differential mode data transmission in
automotive and industrial applications and they are compatible to ISO/DIS 11898. They
work as an interface between the CAN protocol controller and the physical differential
bus in both, 12 V and 24 V systems.
The ICs are based on the Smart Power Technology SPT® which allows bipolar and
CMOS control circuitry in accordance with DMOS power devices existing on the same
monolithic circuit. The TLE6250G is designed to withstand the severe conditions of
automotive applications and provides excellent EMC performance.
Note: There are two versions available (refer to next page).
Data Sheet 4 Rev. 4.0, 2008-04-28
TLE6250
TLE6250G
5 V logic I/O version: RxD, TxD, INH, RM. Two Control pins (RM, INH) and 3 operation
modes: Normal Mode, Stand-by Mode and Receive Only Mode.
TLE6250GV33
3.3 V logic I/O version (logic I/O voltage adaptive to V33 pin within the range 3.3 V to 5 V):
RxD, TxD, INH. One control pin (INH) and two operation modes: Normal Mode and
Standby Mode.
Pin Configuration
Figure 1 Pin Configuration TLE6250G (top view)
Figure 2 Pin Configuration TLE6250GV33 (top view)
AEP03320.VSD
1TxD
2
GND
3
V
CC
4RxD
8
7
6
5
CANH
CANL
INH
RM
TL E6250 G
AEP03321.VSD
1TxD
2
GND
3
V
CC
4RxD
8
7
6
5
CANH
CANL
V
33 V
INH
TLE6250GV 33
TLE6250
Data Sheet 5 Rev. 4.0, 2008-04-28
Table 1 Pin Definitions and Functions TLE6250G
Pin No. Symbol Function
1TxDCAN transmit data input; 20 kΩ pull-up, LOW in dominant state
2GNDGround
3VCC 5 V Supply input
4RxDCAN receive data output; LOW in dominant state,
integrated pull-up
5RMReceive-only input; control input, 20 kΩ pull-up, set low to
activate RxD-only mode
6CANLLow line I/O; LOW in dominant state
7CANHHigh line I/O; HIGH in dominant state
8INHInhibit Input; control input, 20 kΩ pull, set LOW for normal mode
Table 2 Pin Definitions and Functions TLE6250GV33
Pin No. Symbol Function
1TxDCAN transmit data input; 20 kΩ pull-up, LOW in dominant state
2GNDGround
3VCC 5 V Supply input
4RxDCAN receive data output; LOW in dominant state,
integrated pull-up
5V33V Logic supply input; 3.3 V OR 5 V microcontroller logic supply can
be connected here! The digital I/Os of the TLE6250GV33 adopt to
the connected microcontroller logic supply at V33V
6CANLLow line I/O; LOW in dominant state
7CANHHigh line I/O; HIGH in dominant state
8INHInhibit Input; control input, 20 kΩ pull, set LOW for normal mode
Data Sheet 6 Rev. 4.0, 2008-04-28
TLE6250
Functional Block Diagram
Figure 3 Block Diagram TLE6250G
TLE6250 G
Receiver
AEA 03311.VSD
Output
Stage
Driver
Temp-
Protection
Mode Control
*
=
7
CANH
6
CANL
2
GND
TxD
1
3
V
CC
INH
8
RM
5
RxD
4
TLE6250
Data Sheet 7 Rev. 4.0, 2008-04-28
Figure 4 Block Diagram TLE6250GV33
TLE6250 GV33
Receiver
AEA 03312.VSD
Output
Stage
Driver
Temp-
Protection
Mode Control
*
=
7
CANH
6
CANL
2
GND
TxD
1
3
V
CC
INH
8
RxD
4
5
V
33
Data Sheet 8 Rev. 4.0, 2008-04-28
TLE6250
Application Information
Figure 5 Mode State Diagram
Both, the TLE6250G as well as the TLE6250C offer three different operation modes (see
Figure 5), controlled by the INH and RM pin. The TLE6250GV33 offers only two modes,
controlled by the INH (GV33) pin respectively.
AED02924
Normal Mode
INH = 0 RM = 1
INH = 0
Receive-only Mode
RM = 0INH = 1
Stand-by Mode
RM = 0 / 1
INH = 0
and RM = 0
INH = 1
INH = 1
INH = 0
and RM = 1
RM = 0
RM = 1
AEA03327.VSD
Stand-by
Mode
INH = 0
Normal Mode
INH = 1
INH = 0INH = 1
TLE6250G
TLE6250GV33
TLE6250
Data Sheet 9 Rev. 4.0, 2008-04-28
In the normal mode the device is able to receive and to transmit messages whereas in
the receive-only mode signals at the TxD input are not transmitted to the CAN bus. The
receive-only mode can be used for diagnostic purposes (to check the bus connections
between the nodes) as well as to prevent the bus being blocked by a faulty permanent
dominant TxD input signal. The stand-by mode is a low power mode that disables both,
the receiver as well as the transmitter.
In case the receive-only feature is not used the RM pin has to be left open. When the
stand-by mode is not used the INH pin has to be connected to ground level in order to
switch the TLE6250G in normal mode.
Application Information for the 3.3 V Versions
The TLE6250GV33 can be used for both; 3.3 V and 5 V microcontroller logic supply, as
shown in Figure 6. Don’t apply external resistors between the power supply and this pin.
This may cause a voltage drop and so reduce the available voltage at this pin.
Data Sheet 10 Rev. 4.0, 2008-04-28
TLE6250
Figure 6 Application Circuits TLE6250GV33 Used for 3.3 V and 5 V Logic
AEA 03299.VSD
µP
e. g. TLE 4270
INH
8
4
1
5
V
CC
3
100
nF
100
nF
+
V
Q
5 V
GND
GND
GND
V
I
22 µF
100
nF
+22
µF
TL E6250 GV 33
RxD
TxD
V
33 V
5 V
2
CANH
CANL
7
6
AEA 03300.VSD
e. g. TLE 4476
INH
8
RxD 4
TxD
1
5
V
33 V
3
100
nF
GND
GND
V
I
TLE6250 GV 33
V
CC
100
nF
V
Q1
5 V
+100
nF
+22
µF
+22 µF
V
Q2
3.3 V
3.3 V
2
µP
GND
100
nF
22 µF
7
6
CANH
CANL
Application with 3.3 V I/O supply
Application with 5 V I/O supply
TLE6250
Data Sheet 11 Rev. 4.0, 2008-04-28
Figure 6 (cont.) Application Circuits TLE6250GV33 Used for 3.3 V and 5 V Logic
Application with separate 5V power supplies,
AEA 13299.VSD
µP
e. g. TLE 4270
INH
8
4
1
5
V
CC
3
100
nF
100
nF
+
V
Q
5 V
GND
GND
GND
V
I
22 µF
100
nF
+22
µF
TLE6250 GV 33
RxD
TxD
V
33 V
5 V
2
CANH
CANL
7
6
e. g. TLE 4270
V
Q
GND
V
I
100
nF
+22
µF
+
5 V
for applications with switchable transceiver supply
Data Sheet 12 Rev. 4.0, 2008-04-28
TLE6250
Electrical Characteristics TLE6250G (5 V version)
Note: Maximum ratings are absolute ratings; exceeding any one of these values may
cause irreversible damage to the integrated circuit.
Table 3 Absolute Maximum Ratings
Parameter Symbol Limit Values Unit Remarks
Min. Max.
Voltages
Supply voltage VCC -0.3 6.5 V –
CAN input voltage (CANH,
CANL)
VCANH/L -40 40 V –
Logic voltages at INH, RM,
TxD, RxD
VI-0.3 VCC V0 V < VCC < 5.5 V
Electrostatic discharge
voltage at CANH, CANL
VESD -6 6 kV human body model
(100 pF via 1.5 kΩ)
Electrostatic discharge
voltage
VESD -2 2 kV human body model
(100 pF via 1.5 kΩ)
Temperatures
Junction temperature Tj-40 160 °C–
Table 4 Operating Range
Parameter Symbol Limit Values Unit Remarks
Min. Max.
Supply voltage VCC 4.5 5.5 V –
Junction temperature Tj-40 150 °C–
Thermal Resistances
Junction ambient Rthj-a – 185 K/W –
Thermal Shutdown (junction temperature)
Thermal shutdown
temperature
TjsD 160 200 °C 10 °C hysteresis
TLE6250
Data Sheet 13 Rev. 4.0, 2008-04-28
Table 5 Electrical Characteristics
4.5 V < VCC < 5.5 V; RL = 60 Ω; VINH < VINH,ON; -40 °C < Tj < 150 °C; all voltages with
respect to ground; positive current flowing into pin; unless otherwise specified.
Parameter Symbol Limit Values Unit Remarks
Min. Typ. Max.
Current Consumption
Current consumption ICC – 6 10 mA recessive state;
VTxD = VCC
Current consumption ICC – 45 70 mA dominant state;
VTxD = 0 V
Current consumption ICC – 6 10 mA receive-only mode;
RM = low
Current consumption ICC,stb –110µA stand-by mode;
TxD = RM = high
Receiver Output RxD
HIGH level output current IRD,H – -4-2mAVRD = 0.8 × VCC,
Vdiff < 0.4 V1)
LOW level output current IRD,L 24–mAVRD = 0.2 × VCC,
Vdiff > 1 V1)
Transmission Input TxD
HIGH level input voltage
threshold
VTD,H –0.5 ×
VCC
0.7 ×
VCC
V recessive state
LOW level input voltage
threshold
VTD,L 0.3 ×
VCC
0.4 ×
VCC
– V dominant state
TxD pull-up resistance RTD 10 25 50 kΩ–
Inhibit Input (pin INH)
HIGH level input voltage
threshold
VINH,H –0.5 ×
VCC
0.7 ×
VCC
V stand-by mode;
LOW level input voltage
threshold
VINH,L 0.3 ×
VCC
0.4 ×
VCC
– V normal mode
INH pull-up resistance RINH 10 25 50 kΩ–
Data Sheet 14 Rev. 4.0, 2008-04-28
TLE6250
Receive only Input (pin RM) (5 V version only)
HIGH level input voltage
threshold
VRM,H –0.5 ×
VCC
0.7 ×
VCC
V normal mode;
LOW level input voltage
threshold
VRM,L 0.3 ×
VCC
0.4 ×
VCC
– V receive-only mode
RM pull-up resistance RRM 10 25 50 kΩ–
Bus Receiver
Differential receiver
threshold voltage,
recessive to dominant
edge
Vdiff,d – 0.75 0.90 V -20 V < (VCANH, VCANL)
< 25 V
Vdiff = VCANH - VCANL
Differential receiver
threshold voltage
dominant to recessive
edge
Vdiff,r 0.50 0.60 – V -20 V < (VCANH, VCANL)
< 25 V
Vdiff = VCANH - VCANL
Common Mode Range CMR -20 – 25 V VCC = 5 V
Differential receiver
hysteresis
Vdiff,hys – 150 – mV –
CANH, CANL input
resistance
Ri10 20 30 kΩrecessive state
Differential input
resistance
Rdiff 20 40 60 kΩrecessive state
Table 5 Electrical Characteristics (cont’d)
4.5 V < VCC < 5.5 V; RL = 60 Ω; VINH < VINH,ON; -40 °C < Tj < 150 °C; all voltages with
respect to ground; positive current flowing into pin; unless otherwise specified.
Parameter Symbol Limit Values Unit Remarks
Min. Typ. Max.
TLE6250
Data Sheet 15 Rev. 4.0, 2008-04-28
Bus Transmitter
CANL/CANH recessive
output voltage
VCANL/H 0.4 ×
VCC
–0.6 ×
VCC
VVTxD = VCC
CCANH, CANL recessive
output voltage difference
Vdiff = VCANH - VCANL, no
load2)
Vdiff -1 – 0.05 V VTxD = VCC
CANL dominant output
voltage
VCANL ––2.0VVTxD = 0 V;
VCC = 5 V
CANH dominant output
voltage
VCANH 2.8––VVTxD = 0 V;
VCC = 5 V
CANH, CANL dominant
output voltage difference
Vdiff = VCANH - VCANL
Vdiff 1.5 – 3.0 V VTxD = 0 V;
VCC = 5 V
CANL short circuit current ICANLsc 50 120 200 mA VCANLshort = 18 V
– 150 – mA VCANLshort = 36 V
CANH short circuit current ICANHsc -200 -120 -50 mA VCANHshort = 0 V
CANH short circuit current ICANHsc –-120–mAVCANHshort = -5 V
Output current ICANH,lk -50 -300 -400 µAVCC = 0 V,
VCANH = VCANL = -7 V
-50 -100 -150 µAVCC = 0 V,
VCANH = VCANL = -2 V
Output current ICANH,lk 50 280 400 µAVCC = 0 V,
VCANH = VCANL = 7 V
50 100 150 µAVCC = 0 V,
VCANH = VCANL = 2 V
Table 5 Electrical Characteristics (cont’d)
4.5 V < VCC < 5.5 V; RL = 60 Ω; VINH < VINH,ON; -40 °C < Tj < 150 °C; all voltages with
respect to ground; positive current flowing into pin; unless otherwise specified.
Parameter Symbol Limit Values Unit Remarks
Min. Typ. Max.
Data Sheet 16 Rev. 4.0, 2008-04-28
TLE6250
Dynamic CAN-Transceiver Characteristics
Propagation delay TxD-to-
RxD LOW (recessive to
dominant)
td(L),TR – 150 280 ns CL = 47 pF;
RL = 60 Ω;
VCC = 5 V;
CRxD = 20 pF
Propagation delay TxD-to-
RxD HIGH (dominant to
recessive)
td(H),TR – 150 280 ns CL = 47 pF;
RL = 60 Ω;
VCC = 5 V;
CRxD = 20 pF
Propagation delay TxD
LOW to bus dominant
td(L),T – 100 140 ns CL = 47 pF;
RL = 60 Ω;
VCC = 5 V
Propagation delay TxD
HIGH to bus recessive
td(H),T – 100 140 ns CL = 47 pF;
RL = 60 Ω;
VCC = 5 V
Propagation delay bus
dominant to RxD LOW
td(L),R –50140nsCL = 47 pF;
RL = 60 Ω;
VCC = 5 V;
CRxD = 20 pF
Propagation delay bus
recessive to RxD HIGH
td(H),R –50140nsCL = 47 pF;
RL = 60 Ω;
VCC = 5 V;
CRxD = 20 pF
1) Vdiff = VCANH - VCANL
2) Deviation from ISO/DIS 11898
Table 5 Electrical Characteristics (cont’d)
4.5 V < VCC < 5.5 V; RL = 60 Ω; VINH < VINH,ON; -40 °C < Tj < 150 °C; all voltages with
respect to ground; positive current flowing into pin; unless otherwise specified.
Parameter Symbol Limit Values Unit Remarks
Min. Typ. Max.
TLE6250
Data Sheet 17 Rev. 4.0, 2008-04-28
Electrical Characteristics TLE6250GV33 (3.3 V version)
Note: Maximum ratings are absolute ratings; exceeding any one of these values may
cause irreversible damage to the integrated circuit.
Table 6 Absolute Maximum Ratings
Parameter Symbol Limit Values Unit Remarks
Min. Max.
Voltages
Supply voltage VCC -0.3 6.5 V –
3.3 V supply V33V -0.3 6.5 V –
CAN input voltage (CANH,
CANL)
VCANH/L -40 40 V –
Logic voltages at INH, RM,
TxD, RxD
VI-0.3 VCC V0 V < VCC < 5.5 V
Electrostatic discharge
voltage at CANH, CANL
VESD -6 6 kV human body model
(100 pF via 1.5 kΩ)
Electrostatic discharge
voltage
VESD -2 2 kV human body model
(100 pF via 1.5 kΩ)
Temperatures
Junction temperature Tj-40 160 °C–
Table 7 Operating Range
Parameter Symbol Limit Values Unit Remarks
Min. Max.
Supply voltage VCC 4.5 5.5 V –
3.3 V supply voltage V33V 3.0 5.5 V –
Junction temperature Tj-40 150 °C–
Thermal Resistances
Junction ambient Rthj-a – 185 K/W –
Thermal Shutdown (junction temperature)
Thermal shutdown
temperature
TjsD 160 200 °C 10 °C hysteresis
Data Sheet 18 Rev. 4.0, 2008-04-28
TLE6250
Table 8 Electrical Characteristics
4.5 V < VCC < 5.5 V; (3.0 V < V33V < 5.5V for 3.3 V version); RL = 60 Ω; VINH < VINH,ON;
-40 °C < Tj < 150 °C; all voltages with respect to ground; positive current flowing into pin;
unless otherwise specified.
Parameter Symbol Limit Values Unit Remarks
Min. Typ. Max.
Current Consumption (3.3 V version)
Current consumption ICC+33V – 6 10 mA recessive state;
VTxD = V33V
Current consumption ICC+33V – 45 70 mA dominant state;
VTxD = 0 V
Current consumption I33V ––2mA–
Current consumption ICC+33V,stb –110µA stand-by mode,
TxD = high
Receiver Output RxD
HIGH level output
current
IRD,H – -2-1mAVRD = 0.8 × V33V,
Vdiff < 0.4 V1)
LOW level output
current
IRD,L 12–mAVRD = 0.2 × V33V,
Vdiff > 1 V1)
Transmission Input TxD
HIGH level input
voltage threshold
VTD,H –0.55 ×
V33V
0.7 ×
V33V
V recessive state
LOW level input
voltage threshold
VTD,L 0.3 ×
V33V
0.45 ×
V33V
– V dominant state
TxD pull-up resistance RTD 10 25 50 kΩ–
Inhibit Input (pin INH)
HIGH level input
voltage threshold
VINH,H –0.55 ×
V33V
0.7 ×
V33V
V stand-by mode;
LOW level input
voltage threshold
VINH,L 0.3 ×
V33V
0.45 ×
V33V
– V normal mode;
INH pull-up resistance RINH 10 25 50 kΩ–
TLE6250
Data Sheet 19 Rev. 4.0, 2008-04-28
Bus Receiver
Differential receiver
threshold voltage,
recessive to dominant
edge
Vdiff,d – 0.75 0.90 V -20 V < (VCANH, VCANL)
< 25 V
Vdiff = VCANH - VCANL
Differential receiver
threshold voltage,
dominant to recessive
edge
Vdiff,r 0.50 0.60 – V -20 V < (VCANH, VCANL)
< 25 V
Vdiff = VCANH - VCANL
Common Mode Range CMR -20 – 25 V VCC = 5 V
Differential receiver
hysteresis
Vdiff,hys –150–mV–
CANH, CANL input
resistance
Ri10 20 30 kΩrecessive state
Differential input
resistance
Rdiff 20 40 60 kΩrecessive state
Table 8 Electrical Characteristics (cont’d)
4.5 V < VCC < 5.5 V; (3.0 V < V33V < 5.5V for 3.3 V version); RL = 60 Ω; VINH < VINH,ON;
-40 °C < Tj < 150 °C; all voltages with respect to ground; positive current flowing into pin;
unless otherwise specified.
Parameter Symbol Limit Values Unit Remarks
Min. Typ. Max.
Data Sheet 20 Rev. 4.0, 2008-04-28
TLE6250
Bus Transmitter
CANL/CANH
recessive output
voltage
VCANL/H 0.4 ×
VCC
–0.6 ×
VCC
VVTxD = V33V
CANH, CANL
recessive output
voltage difference
Vdiff = VCANH - VCANL,
no load2)
Vdiff -1 – 0.05 V VTxD = V33V
CANL dominant
output voltage
VCANL ––2.0VVTxD = 0 V;
VCC = 5 V
CANH dominant
output voltage
VCANH 2.8 – – V VTxD = 0 V;
VCC = 5 V
CANH, CANL
dominant output
voltage difference
Vdiff = VCANH - VCANL
Vdiff 1.5 – 3.0 V VTxD = 0 V;
VCC = 5 V
CANL short circuit
current
ICANLsc 50 120 200 mA VCANLshort = 18 V
–150–mA
VCANLshort = 36 V
CANH short circuit
current
ICANHsc -200 -120 -50 mA VCANHshort = 0 V
CANH short circuit
current
ICANHsc –-120–mAVCANHshort = -5 V
Output current ICANH/L,lk -50 -300 -400 µAVCC = 0 V,
VCANH = VCANL = -7 V
-50 -100 -150 µAVCC = 0 V,
VCANH =VCANL = -2 V
Output current ICANH/L,lk 50 280 400 µAVCC = 0 V,
VCANH = VCANL = 7 V
50 100 150 µAVCC = 0 V,
VCANH = VCANL = 2 V
Table 8 Electrical Characteristics (cont’d)
4.5 V < VCC < 5.5 V; (3.0 V < V33V < 5.5V for 3.3 V version); RL = 60 Ω; VINH < VINH,ON;
-40 °C < Tj < 150 °C; all voltages with respect to ground; positive current flowing into pin;
unless otherwise specified.
Parameter Symbol Limit Values Unit Remarks
Min. Typ. Max.
TLE6250
Data Sheet 21 Rev. 4.0, 2008-04-28
Dynamic CAN-Transceiver Characteristics
Propagation delay
TxD-to-RxD LOW
(recessive to
dominant)
td(L),TR – 150 280 ns CL = 47 pF;
RL = 60 Ω;
VCC = 5 V;
CRxD = 20 pF
Propagation delay
TxD-to-RxD HIGH
(dominant to
recessive)
td(H),TR – 150 280 ns CL = 47 pF;
RL = 60 Ω;
VCC = 5 V;
CRxD = 20 pF
Propagation delay
TxD LOW to bus
dominant
td(L),T – 100 140 ns CL = 47 pF;
RL = 60 Ω;
VCC = 5 V
Propagation delay
TxD HIGH to bus
recessive
td(H),T – 100 140 ns CL = 47 pF;
RL = 60 Ω;
VCC = 5 V
Propagation delay bus
dominant to RxD LOW
td(L),R – 50 140 ns CL = 47 pF;
RL = 60 Ω;
VCC = 5 V;
CRxD = 20 pF
Propagation delay bus
recessive to RxD
HIGH
td(H),R – 50 140 ns CL = 47 pF;
RL = 60 Ω;
VCC = 5 V;
CRxD = 20 pF
1) Vdiff = VCANH - VCANL
2) Deviation from ISO/DIS 11898
Table 8 Electrical Characteristics (cont’d)
4.5 V < VCC < 5.5 V; (3.0 V < V33V < 5.5V for 3.3 V version); RL = 60 Ω; VINH < VINH,ON;
-40 °C < Tj < 150 °C; all voltages with respect to ground; positive current flowing into pin;
unless otherwise specified.
Parameter Symbol Limit Values Unit Remarks
Min. Typ. Max.
Data Sheet 22 Rev. 4.0, 2008-04-28
TLE6250
Diagrams
Figure 7 Test Circuit for Dynamic Characteristics (5 V Version)
Figure 8 Test Circuit for Dynamic Characteristics (GV33 Version)
AEA03328.VSD
3
GND
VCC
2
4
INH 8
TxD 1
RM 5
100 nF
5 V
6CANL
7CANH
60 Ω
47 pF
RxD
20 pF
AEA03329.VSD
3
GND
VCC
2
5
V33 V
INH 8
TxD 1
RxD 4
100 nF
5 V
3.3 V
100 nF
20 pF
6CANL
7CANH
60 Ω
47 pF
TLE6250
Data Sheet 23 Rev. 4.0, 2008-04-28
Figure 9 Timing Diagrams for Dynamic Characteristics
AET02926
TxD
V
V
CC(33V)
GND
V
DIFF d(L), T
t
d(H), T
t
V
DIFF(d)
DIFF(r)
V
t
t
GND
CC(33V)
V
V
RxD
t
d(L), R
t
d(H), R
t
CC(33V)
V
0.7
0.3
CC(33V)
V
d(L), TR
t
d(H), TR
t
Data Sheet 24 Rev. 4.0, 2008-04-28
TLE6250
Application
Figure 10 Application Circuit TLE6250G with TLE6250GV33
ECU 1
ECU X
µP
e. g . TLE 4270
e. g . TLE 4476
µP
120
Ω
AEA03308.VSD
RM 5
INH 8
RxD 4
TxD 1
V
CC
3
CANH
CANL
7
6
100
nF
100
nF
+
V
Q
5 V
GND
GND
GND
V
I
22 µF
100
nF
+22
µF
TL E6250 G
INH
8
RxD 4
TxD
1
5
V
33 V
3
CANH
CANL
7
6
100
nF
GND
GND
V
I
TL E6250 GV33
V
CC
GND
100
nF
100
nF
V
Q1
5 V
+
100
nF
+22
µF
+22 µF
V
Q2
3.3 V
22 µF
CAN
Bus
V
Bat
120
Ω
2
2
TLE6250
Data Sheet 25 Rev. 4.0, 2008-04-28
Package Outlines
Figure 11 PG-DSO-8 (PG-DSO-8-16 Plastic Dual Small Outline)
Green Product (RoHS compliant)
To meet the world-wide customer requirements for environmentally friendly products
and to be compliant with government regulations the device is available as a green
product. Green products are RoHS-Compliant (i.e Pb-free finish on leads and suitable
for Pb-free soldering according to IPC/JEDEC J-STD-020).
+0.06
0.19
0.35 x 45˚
1)
-0.2
4
C
8 MAX.
0.64
±0.2
6
±0.25
0.2 8x
MC
1.27
+0.1
0.41 0.2 MA
-0.06
1.75 MAX.
(1.45)
±0.07
0.175
B
8x
B
2)
Index Marking
5-0.21)
41
85
A
1) Does not include plastic or metal protrusion of 0.15 max. per side
2) Lead width can be 0.61 max. in dambar area
GPS01181
0.1
You can find all of our packages, sorts of packing and others in our
Infineon Internet Page “Products”: http://www.infineon.com/products.
Dimensions in mm
SMD = Surface Mounted Device
Template: central_tmplt_a5.fm / 5 / 2003-04-01
TLE6250
Revision History: 2008-04-28 Rev. 4.0
Previous Version:Rev. 3.9 (Data Sheet)
Page Correction inside the TLE6250GV33 characteristics
Page 20 Changed symbol for the leakage current CANH/L:
From ICANH,lk to ICANH/L,lk
Changed maximum limit for the parameter:
Output current, ICANH/L,lk, VCC = 0 V,VCANH = VCANL = 7 V:
From 300 µA to 400 µA
Page 26 updated Revision History
