Analog Devices Welcomes Hittite Microwave Corporation NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED www.analog.com www.hittite.com THIS PAGE INTENTIONALLY LEFT BLANK HMC601LP4 / 601LP4E v01.0509 75 dB, FAST SETTLING, LOGARITHMIC DETECTOR / CONTROLLER 10 - 4000 MHz Typical Applications Features The HMC601LP4(E) is ideal for IF and RF applications in: Wide Dynamic Range: up to 75 dB * Cellular/PCS/3G Flexible Supply Voltage: +2.7V to +5.5V * WiMAX, WiBro & Fixed Wireless Power-Down Mode * Power Monitoring & Control Circuitry Excellent Stability over Temperature * Receiver Signal Strength Indication (RSSI) Compact 4x4mm Leadless SMT Package Fast Pulse Response: 15/34ns (Rise/Fall Time) * Automatic Gain & Power Control Circuits POWER DETECTORS - SMT 12 Functional Diagram General Description The HMC601LP4(E) Logarithmic Detector/Controller converts RF signals at its input, to a proportional DC voltage at its output. The HMC601LP4(E) employ a successive compression topology which delivers extremely high dynamic range and conversion accuracy over a wide input frequency range. As the input power is increased, successive amplifiers move into saturation one by one creating an accurate approximation of the logarithm function. The output of a series of square law detectors is summed, converted into voltage domain and buffered to drive the LOGOUT output. For detection mode, the LOGOUT pin is shorted to the VSET input, and will provide a nominal logarithmic slope of 19mV/dB and an intercept of -100dBm. The HMC601LP4(E) can also be used in the controller mode where an external voltage is applied to the VSET pin, to create an AGC or APC feedback loop. The HMC601LP4(E) provides a 15/34ns (rise/fall time) response time enabling RF burst detection to a pulse rate beyond 20 MHz. Electrical Specifi cations, TA = +25C, PWD = 0V, Vcc1, Vcc2 = +3.3V [1] Parameter Input Frequency Typ. Typ. Typ. Typ. Typ. Typ. Typ. Typ. Units 50 100 500 900 1900 2500 3500 4000 MHz 3 dB Dynamic Range 74 74 74 74 70 68 54 52 dB 3 dB Dynamic Range Center -31 -31 -31 -31 -31.5 -31.5 -27 -23 dBm 1 dB Dynamic Range Output Slope Output Intercept Temperature Sensitivity @ -10 dBm Input [2] 68 68 69 69 67 65 47 46 dB 19.5 19.4 19.2 19.1 19.0 19.4 20.9 19.6 mV/dB -99 -99 -100 -100 -98 -96 -85 -79 dBm -4.2 -3.8 -3.5 -2.4 -0.8 -0.8 -4.4 -3.5 mdB/C [1] Detector mode measurements; LOGOUT (Pin 17) is shorted to VSET (Pin 16). [2] Measured from TA = -40C to TA = +85C Parameter Conditions Min. Typ. Max. Units RF Input (INP) Return Loss F = 10 - 4000 MHz, Zo = 50, See plot 10 dB (Simulated) 12 k LOGOUT Interface Open Loop Impedance 12 - 10 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC601LP4 / 601LP4E v01.0509 75 dB, FAST SETTLING, LOGARITHMIC DETECTOR / CONTROLLER 10 - 4000 MHz Electrical Specifi cations, (continued) Parameter Conditions Min. Typ. Current Drive (Source) Current Drive (Sink) For 1% change in the output voltage Output Voltage Range Max. mA 4.8 mA 0 Small Signal Response Time (10% to 90%) Large Signal Response Time (0.5 dB Settling) Units 0.55 Vcc -0.13 V Pin = -60 to -57 dBm 8 ns Pin = No Signal to 0 dBm 50 ns Output Rise Time Ripple From 0% to 90% 15 ns Fin = 100 MHz <4 mVpp 30 k VSET Interface Input Voltage Range Low Frequency Gain 0.6 to 1.9 V 75 dB 4.4 kHz VSET to LOGOUT Open Loop Corner Frequency 12 POWER DETECTORS - SMT Input Impedance Power Down (PWD) Interface Voltage Range for Normal Mode Voltage Range for Shutdown Mode 0 0.2 x Vcc V 0.8 x Vcc Vcc V Threshold Voltage Power-up Response Time Vcc/2 V 50% PWD to 0.5 dB Settling of LOGOUT 19.9 s 50% PWD to 10% Icc 2.2 s Power-Down Response Time Power Supply (Vcc1, Vcc2) Operating Voltage Range 2.7 Supply Current in Normal Mode Vcc = +3.3V, PWD = 0V 30 Supply Current in Power Down Mode Vcc = +3.3V, PWD = Vcc 1 5.5 V 36 mA mA Test Conditions Parameter Condition Vcc1, Vcc2 +3.3V Input Zo 50 TA +25C Fin 900 MHz INN Port connected to ground through a 1000pF capacitor LOGOUT Voltage & Error vs. Input Power, Fin = 10 MHz LOGOUT Voltage & Error vs. Input Power, Fin = 50 MHz 5 2 IDEAL LOGOUT +25C LOGOUT +85C LOGOUT -40C 3 0.8 -1 0.4 ERR +25C ERR +85C ERR -40C 0 -75 -65 -55 -45 -35 -25 -15 -5 LOGOUT (V) 1 1.2 1 0.8 -1 -3 0.4 -5 0 5 INPUT POWER (dBm) 3 -75 ERROR (dB) 1.2 IDEAL LOGOUT +25C LOGOUT +85C LOGOUT -40C 1.6 ERROR (dB) LOGOUT (V) 1.6 5 2 -3 ERR +25C ERR +85C ERR -40C -5 -65 -55 -45 -35 -25 -15 -5 5 INPUT POWER (dBm) Unless otherwise noted: Vcc1, Vcc2 = +3.3V, TA = +25C For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 12 - 11 HMC601LP4 / 601LP4E v01.0509 75 dB, FAST SETTLING, LOGARITHMIC DETECTOR / CONTROLLER 10 - 4000 MHz LOGOUT Voltage & Error vs. Input Power, Fin = 100 MHz LOGOUT Voltage & Error vs. Input Power, Fin = 500 MHz IDEAL LOGOUT +25C LOGOUT +85C LOGOUT -40C 3 1.6 1 0.8 -1 ERR +25C ERR +85C ERR -40C 0 -75 -65 -55 -45 -35 -25 -15 -5 IDEAL LOGOUT +25C LOGOUT +85C LOGOUT -40C 1 0.8 -1 0.4 -5 0 ERR +25C ERR +85C ERR -40C -65 -55 3 1.6 1 0.8 -1 ERR +25C ERR +85C ERR -40C 0 -45 -35 -25 -15 -5 LOGOUT (V) 2 1.2 -55 IDEAL LOGOUT +25C LOGOUT +85C LOGOUT -40C 0.8 -1 -5 0 -5 -65 -55 3 1.6 ERR +25C ERR +85C ERR -40C 0 -25 -35 -25 -15 5 -15 -5 LOGOUT +25C LOGOUT +85C LOGOUT -40C 3 1 0.8 -1 0.4 -5 0 5 5 1.2 -3 INPUT POWER (dBm) -3 ERR +25C ERR +85C ERR -40C IDEAL -75 -65 -5 -55 -45 -35 -25 -15 INPUT POWER (dBm) Unless otherwise noted: Vcc1, Vcc2 = +3.3V, TA = +25C 12 - 12 -5 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com -5 5 ERROR (dB) -1 LOGOUT (V) 2 ERROR (dB) LOGOUT (V) 5 0.8 -35 -45 LOGOUT Voltage & Error vs. Input Power, Fin = 3500 MHz 1 -45 -3 ERR +25C ERR +85C ERR -40C -75 1.2 -55 3 INPUT POWER (dBm) IDEAL LOGOUT +25C LOGOUT +85C LOGOUT -40C -65 5 1 0.4 5 2 -75 -5 1.2 -3 LOGOUT Voltage & Error vs. Input Power, Fin = 2500 MHz 0.4 -15 5 INPUT POWER (dBm) 1.6 -25 ERROR (dB) LOGOUT (V) 5 ERROR (dB) POWER DETECTORS - SMT IDEAL LOGOUT +25C LOGOUT +85C LOGOUT -40C -65 -35 LOGOUT Voltage & Error vs. Input Power, Fin = 1900 MHz 2 -75 -45 INPUT POWER (dBm) LOGOUT Voltage & Error vs. Input Power, Fin = 900 MHz 0.4 -3 -5 -75 INPUT POWER (dBm) 1.6 3 1.2 -3 5 5 ERROR (dB) 1.2 0.4 12 2 ERROR (dB) LOGOUT (V) 1.6 5 LOGOUT (V) 2 HMC601LP4 / 601LP4E v01.0509 75 dB, FAST SETTLING, LOGARITHMIC DETECTOR / CONTROLLER 10 - 4000 MHz LOGOUT Voltage & Error vs. Input Power, Fin = 4000 MHz LOGOUT Slope vs. Frequency, Vcc = 3.3V 5 2 LOGOUT +25C LOGOUT +85C LOGOUT -40C 0.8 -1 -3 ERR +25C ERR +85C ERR -40C -75 -65 -55 -45 -35 -25 -15 -5 21 20 19 -5 0 +25 C +85 C -40 C 22 18 500 5 1000 1500 2500 3000 3500 4000 LOGOUT Slope vs. Supply Voltage, TA = +25C 3000 3500 4000 LOGOUT Intercept vs. Frequency, Vcc = 3.3V 25 -60 500 MHz 900 MHz 1900 MHz 23 2500 MHz 3500 MHz 4000 MHz +25 C +85 C -40 C -70 INTERCEPT (dBm) 24 22 21 20 -80 -90 -100 19 18 2.5 3 3.5 4 4.5 5 5.5 -110 500 1000 1500 Vcc (Volts) 2500 LOGOUT Error vs. Input Power, Normalized [2], Fin = 1900 MHz 2 500 MHz 900 MHz 900 MHz 1900 MHz -60 RELATIVE ERROR TO 27C (dB) -50 INTERCEPT (dBm) 2000 FREQUENCY (MHz) LOGOUT Intercept vs. Supply Voltage TA = +25C 2500 MHz 3500 MHz 4000 MHz -70 -80 -90 -100 -110 2.5 12 FREQUENCY (MHz) INPUT POWER (dBm) SLOPE (mV/dB) 2000 POWER DETECTORS - SMT IDEAL SLOPE (mV/dB) 1.2 1 0.4 23 3 ERROR (dB) LOGOUT (V) 1.6 24 3 3.5 4 4.5 5 5.5 Vcc (VOLTS) +85 C -40 C 1 0 -1 -2 -75 -65 -55 -45 -35 -25 -15 -5 5 INPUT POWER (dBm) Unless otherwise noted: Vcc1, Vcc2 = +3.3V, TA = +25C For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 12 - 13 HMC601LP4 / 601LP4E v01.0509 75 dB, FAST SETTLING, LOGARITHMIC DETECTOR / CONTROLLER 10 - 4000 MHz LOGOUT Voltage vs. Input Power & Frequency, TA = +25C Input Return Loss vs. Frequency 2.4 -5 -15 -20 -25 +25 C +85 C -40 C -30 POWER DETECTORS - SMT 12 50 MHz 900 MHz 1900 MHz 3500 MHz 4000 MHz 1.9 -10 LOGOUT (V) INPUT RETURN LOSS (dB) 0 0.9 0.4 -70 -35 0 1 2 3 4 1.4 5 -60 -50 -40 -30 -20 -10 0 10 INPUT POWER (dBm) FREQUENCY (GHz) Absolute Maximum Ratings Vcc1, Vcc2 0V to +5.5V PWD 0V to +5.5V VSET Input Voltage 0V to +5.5V LOGOUT Output Current 3 mA RF Input Power +12 dBm Junction Temperature 125 C Continuous Pdiss (T = 85C) (Derate 7.95 mW/C above 85C) 0.32 Watts Thermal Resistance (Rth) (junction to lead) 126 C/W Storage Temperature -65 to +150 C Operating Temperature -40 to +85 C ESD Sensitivity (HBM) Class 1C ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS [1] Unless otherwise noted: Vcc1, Vcc2 = +3.3V, TA = +25C [2] This data is relative to the room temperature performance of the HMC601LP4 Outline Drawing NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS]. 3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE 4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM. PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM. 5. PACKAGE WARP SHALL NOT EXCEED 0.05mm. 6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED PCB LAND PATTERN. 12 - 14 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC601LP4 / 601LP4E v01.0509 75 dB, FAST SETTLING, LOGARITHMIC DETECTOR / CONTROLLER 10 - 4000 MHz Package Information Part Number Package Body Material Lead Finish MSL Rating HMC601LP4 Low Stress Injection Molded Plastic Sn/Pb Solder MSL1 HMC601LP4E RoHS-compliant Low Stress Injection Molded Plastic 100% matte Sn MSL1 Package Marking [3] [1] H601 XXXX [2] H601 XXXX [1] Max peak reflow temperature of 235 C [2] Max peak reflow temperature of 260 C [3] 4-Digit lot number XXXX 12 Pin Descriptions Function Description 1, 6, 7-13, 15, 18-24 N/C These pins are not connected internally; however, this product is specified with these pins connected to RF/DC ground. 2, 5 Vcc1, Vcc2 Bias supply. Connect supply voltage to both pins. 3, 4 INP, INN RF Input pins. Connect RF to INP, and AC couple INN to ground for single-ended operation. Interface Schematic Apply PWD >0.8xVcc to initiate a power saving shutdown mode. 14 PWD 16 VSET VSET input in controller mode. Short this pin to LOGOUT for detector mode. 17 LOGOUT Logarithmic output that converts the input power to a DC level in detector mode. Short this pin to VSET for detector mode. Package Base GND Exposed paddle must be connected to RF and DC ground. POWER DETECTORS - SMT Pin Number To ensure proper start-up apply the power-up sequence shown in the "Power-Up Timing Diagram" attached to the application circuit. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 12 - 15 HMC601LP4 / 601LP4E v01.0509 75 dB, FAST SETTLING, LOGARITHMIC DETECTOR / CONTROLLER 10 - 4000 MHz Evaluation PCB POWER DETECTORS - SMT 12 List of Materials for Evaluation PCB 115242 [1] Item Description J1 - J4 PC Mount SMA Connector J5 - J8 DC Pin C1, C2 1000 pF Capacitor, 0402 Pkg. C3, C4 0.1F Capacitor, 0402 Pkg. R1, R2 5.6 Resistor, 0603 Pkg. R3-R5 0 Resistor, 0603 Pkg. U1 HMC601LP4 / HMC601LP4E Logarithmic Detector / Controller PCB [2] 115244 Evaluation PCB The circuit board used in the final application should use RF circuit design techniques. Signal lines should have 50 ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350 12 - 16 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC601LP4 / 601LP4E v01.0509 75 dB, FAST SETTLING, LOGARITHMIC DETECTOR / CONTROLLER 10 - 4000 MHz Application & Evaluation PCB Schematic Notes Note 1: The HMC601LP4 & HMC601LP4E evaluation boards are pre-assembled for single-ended input, and detector/RSSI mode. Note 2: For single-ended input operation, use the INP port and make no connection to INN. INN is AC coupled to ground by C2 Note 3: For differential input, remove C2, and install a 1000pF capacitor in series with INN at location shown. Note 4: For detector mode, connect high impedence volt meter to the LOGOUT port, and make no connection to VSET. LOGOUT is shorted to VSET by R3, as required for detector mode. Note 5: For controller mode, remove R3 and make appropriate connection to LOGOUT and VSET. In controller mode, the LOGOUT output can be used to drive a variable gain amplifier, or a variable attenuator, either directly or through a buffer or microcontroller. VSET should be connected to an external supply, typically between +0.6 and +1.9V. Power-Up Timing Diagram For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com POWER DETECTORS - SMT 12 12 - 17 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Analog Devices Inc.: 115242-HMC601LP4 HMC601LP4E HMC601LP4ETR HMC601LP4 HMC601LP4TR