VO3020, VO3021, VO3022, VO3023 www.vishay.com Vishay Semiconductors Optocoupler, Phototriac Output, 400 VDRM FEATURES * 400 V blocking voltage * Isolation test voltage, 5000 VRMS, t = 1 min * Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 Note: pin 5 must not be connected ~ ~ 6 5 4 APPLICATIONS * High current triac driver * Solid-state relay 1 A (+) 2 C (-) 3 NC * Switch small AC loads AGENCY APPROVALS (all parts are certified under base model VO3020) * UL1577, file no. E52744 double protection i179004-14 * cUL tested to CSA 22.2 bulletin 5A DESCRIPTION * DIN EN 60747-5-5 (VDE 0884-5), available with option 1 The VO3020 series consists of a phototriac optically coupled to a gallium arsenide infrared-emitting diode in a 6-lead plastic dual inline package * CQC GB8898-2011, GB4943.1-2011 * FIMKO EN 60950-1 ORDERING INFORMATION V O 3 0 2 # - PART NUMBER X 0 0 PACKAGE OPTION # DIP-6 Option 6 7.62 mm 10.16 mm T TAPE AND REEL Option 7 > 8 mm AGENCY CERTIFIED / PACKAGE UL, cUL, CQC DIP-6 TRIGGER CURRENT, IFT 5 mA 10 mA 15 mA 30 mA VO3023 VO3022 VO3021 VO3020 DIP-6, 400 mil, option 6 VO3023-X006 VO3022-X006 VO3021-X006 VO3020-X006 SMD-6, option 7 VO3023-X007T VO3022-X007T VO3021-X007T VO3020-X007T 5 mA 10 mA 15 mA 30 mA DIP-6 VDE, UL, cUL, FIMKO, CQC VO3023-X001 VO3022-X001 VO3021-X001 VO3020-X001 SMD-6, option 7 VO3023-X017T - VO3021-X017T VO3020-X017T Note * Additional options may be possible, please contact sales office Document Number: 84132 1 For technical questions, contact: optocoupleranswers@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Rev. 1.3, 07-Mar-18 VO3020, VO3021, VO3022, VO3023 www.vishay.com Vishay Semiconductors ABSOLUTE MAXIMUM RATINGS (Tamb = 25 C, unless otherwise specified) PARAMETER TEST CONDITION SYMBOL VALUE UNIT INPUT Reverse voltage VR 6 V Forward current IF 50 mA Peak surge current 100 s, 200 pps IFSM 0.5 A Pdiss 70 mW Peak off-state voltage VDRM 400 V RMS on-state current IT(RMS) 0.1 A Power dissipation OUTPUT Peak non-repetitive surge current PW = 100 ms, 120 pps ITSM 1 A Pdiss 300 mW VISO 5000 VRMS Ptot 330 mW Storage temperature range Tstg -55 to +150 C Ambient temperature Tamb -40 to +100 C Tsld 260 C Tj 125 C Power dissipation COUPLER Isolation voltage t = 1 min Total power dissipation Lead soldering temperature (1) 2 mm from case, t < 10 s Junction temperature 100 80 Ptot - Total Power Dissipation (mW) Ptot - Total Power Dissipation (mW) Notes * Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. Functional operation of the device is not implied at these or any other conditions in excess of those given in the operational sections of this document. Exposure to absolute maximum ratings for extended periods of the time can adversely affect reliability. (1) Refer to reflow profile for soldering conditions for surface mounted devices (SMD). Refer to wave profile for soldering conditions for through hole devices (DIP) IR-diode 60 40 20 0 0 25 50 75 100 125 Tamb - Ambient Temperature (C) Fig. 1 - Total Power Dissipation vs. Ambient Temperature (IR-Diode) 350 300 Phototriac 250 200 150 100 50 0 0 25 50 75 100 125 Tamb - Ambient Temperature (C) Fig. 2 - Total Power Dissipation vs. Ambient Temperature (Phototriac) Document Number: 84132 2 For technical questions, contact: optocoupleranswers@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Rev. 1.3, 07-Mar-18 VO3020, VO3021, VO3022, VO3023 www.vishay.com Vishay Semiconductors ELECTRICAL CHARACTERISTICS (Tamb = 25 C, unless otherwise specified) PARAMETER TEST CONDITION PART SYMBOL MIN. TYP. MAX. UNIT INPUT Forward voltage IF = 20 mA VF - 1.3 1.5 V Reverse voltage IR = 10 A VR 6 - - V Reverse current VR = 6 V IR - - 10 A VR = 0 V, f = 1 MHz Cj - 50 - pF Peak off-state current, either direction VDRM = 400 V (1) IDRM - 10 100 nA Peak off-state voltage, either direction ITM = 100 mA VTM - 1.7 3 V IF = 0 A, VD = 0.67 VDRM dV/dtcr 100 - - V/s VO3020 IFT - 15 30 mA VO3021 IFT - 8 15 mA VO3022 IFT - 5 10 mA VO3023 IFT - 3 5 mA IH - 200 - A Junction capacitance OUTPUT Critical rate of rise of off-state voltage COUPLER (2) VS = 3 V, RL = 150 Emitting diode trigger current IF = 10 mA, VS 3 V Holding current Notes * Minimum and maximum values are testing requirements. Typical values are characteristics of the device and are the result of engineering evaluation. Typical values are for information only and are not part of the testing requirements (1) Test voltage must be applied within dV/dt ratings (2) I is defined as a minimum trigger current FT SAFETY AND INSULATION RATINGS PARAMETER SYMBOL VALUE UNIT Output safety power PSO 700 mW Input safety current Isi 400 mA Safety temperature TS 175 C Comparative tracking index CTI 175 MAXIMUM SAFETY RATINGS INSULATION RATED PARAMETERS Maximum withstanding isolation voltage Maximum transient isolation voltage Maximum repetitive peak isolation voltage VISO 5000 VIOTM 8000 Vpeak VIORM 890 Vpeak VIORM 1140 (1) Vpeak VRMS Insulation resistance Tamb = 25 C, VDC = 500 V RIO 1012 Isolation resistance Tamb = 100 C, VDC = 500 V RIO 1011 Climatic classification (according to IEC 68 part 1) 55 / 115 / 21 Environment (pollution degree in accordance to DIN VDE 0109) 2 Creepage distance (standard DIP-6) 7 mm Creepage distance (400 mil DIP-6) 8 mm Clearance distance (standard DIP-6) 7 mm Clearance distance (400 mil DIP-6) Insulation thickness DTI 8 mm 0.4 mm Notes * As per DIN EN 60747-5-5, 7.4.3.8.2, this optocoupler is suitable for "safe electrical insulation" only within the safety ratings. Compliance with the safety ratings shall be ensured by means of protective circuits (1) 400 mil, option 6 only Document Number: 84132 3 For technical questions, contact: optocoupleranswers@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Rev. 1.3, 07-Mar-18 VO3020, VO3021, VO3022, VO3023 www.vishay.com Vishay Semiconductors 100 IF - Forward Current (mA) Tamb = 0 C Tamb = 25 C Tamb = 50 C Tamb = 75 C 10 Tamb = 100 C Tamb = -25 C Tamb = -40 C 1 0.8 1.0 1.2 1.4 1.6 IDRM - Off-State Leakage Current (A) TYPICAL CHARACTERISTICS (Tamb = 25 C, unless otherwise specified) 10 1 0.1 0.01 0.001 -40 VF - Forward Voltage (V) 80 60 40 20 0 0 20 40 60 40 60 80 100 80 100 1.5 1.3 1.1 0.9 0.7 0.5 -40 TAmb - Ambient Temperature(C) -20 0 20 40 60 80 100 Tamb - Ambient Temperature (C) Fig. 4 - Reverse Voltage vs. Ambient Temperature Fig. 7 - Normalized Trigger Current vs. Ambient Temperature 100 100 VL = 7 V 75 Turn-On Time (s) ITM - On-State Current (mA) 20 Fig. 6 - Off-State Leakage Current vs. Ambient Temperature IFT - Normalized Trigger Current (mA) VR - Reverse Voltage (V) 100 -20 0 Tamb - Ambient Temperature (C) Fig. 3 - Forward Current vs. Forward Voltage -40 -20 50 25 0 -25 10 - 50 -75 1 -100 -2.5 -1.5 -0.5 0.5 1.5 2.5 VTM - On-State Voltage (V) Fig. 5 - On-State Current vs. On-State Voltage 0 10 20 30 40 50 IFT - Trigger Current (mA) Fig. 8 - Turn-On Time vs. Trigger Current Document Number: 84132 4 For technical questions, contact: optocoupleranswers@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Rev. 1.3, 07-Mar-18 VO3020, VO3021, VO3022, VO3023 Vishay Semiconductors 4.0 2.5 IFT - Trigger Current (mA) IH - Normalized Holding Current (A) www.vishay.com 2.0 1.5 1.0 0.5 3.5 3.0 2.5 2.0 1.5 1.0 0 -40 -20 0 20 40 60 80 0 100 100 200 300 400 VLoad - Voltage Load (V) Tamb - Ambient Temperature (C) Fig. 9 - Normalized Holding Current vs. Ambient Temperature Fig. 12 - Trigger Current vs. Voltage Load 100 -0.8 VL = 7 V Coefficienrt (mV/C) tGD - Delay Time (s) -0.7 10 1 -0.6 -0.5 -0.4 -0.3 - 0.2 10 20 30 40 50 1 10 IFT - Trigger Current (mA) IF (mA) Fig. 10 - Delay Time vs. Trigger Current Fig. 13 - Coefficient vs. Forward Current 1100 8 VL = 7 V 1000 7 900 800 6 VDRM (V) IFT - Trigger Current (mA) 100 5 700 600 500 400 4 300 200 3 100 2 0 20 40 60 80 100 PW -Trigger Pulse Width (s) Fig. 11 - Trigger Current vs. Trigger Pulse Width -40 -20 0 20 40 60 80 100 Tamb (C) Fig. 14 - Peak Off-State Voltage vs. Ambient Temperature Document Number: 84132 5 For technical questions, contact: optocoupleranswers@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Rev. 1.3, 07-Mar-18 VO3020, VO3021, VO3022, VO3023 www.vishay.com Vishay Semiconductors 1.4 1.2 NVDRM (V) 1.0 0.8 0.6 0.4 0.2 0 -40 -20 0 20 40 60 80 100 Tamb (C) Fig. 15 - Normalized Off-State Voltage M2/M1 vs. Ambient Temperature PACKAGE DIMENSIONS in millimeters 6 5 4 6.5 0.5 1 2 3 7.3 0.5 7.62 0.3 3.5 0.3 0.5 typ. 3.3 0.5 2.8 0.5 0.26 0.5 0.1 2.54 0.25 7.62 to 9.98 Option 6 Option 7 7.62 0.3 7.62 0.3 0.76 2.54 0.26 1.78 6.9 0.5 1.0 0.25 2.3 0.5 R 0.25 8 min. 11.05 1.52 10.15 0.3 10.16 0.5 0.26 Document Number: 84132 6 For technical questions, contact: optocoupleranswers@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Rev. 1.3, 07-Mar-18 VO3020, VO3021, VO3022, VO3023 www.vishay.com Vishay Semiconductors PACKAGE MARKING VO3020 V YWW 25 Fig. 16 - Example VO3020-X017T Notes * VDE logo is only marked on option 1 parts. Option information is not marked on the part * Tape and reel suffix (T) is not part of the package marking PACKING INFORMATION DEVICES PER TUBE TYPE UNITS/TUBE TUBES/BOX UNITS/BOX DIP-6 50 40 2000 2 0.1 O 1.55 0.05 4 0.1 1.75 0.1 7.5 0.1 16 0.3 12 0.1 0.3 0.05 22537-1 Fig. 17 - Tape and Reel Drawing, 1000 Units per Reel REEL DIMENSIONS in millimeters ESD sticker Tape slot in core 330 (13") Regular, special or bar code label 17999 Fig. 18 - Reel Dimensions Document Number: 84132 7 For technical questions, contact: optocoupleranswers@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Rev. 1.3, 07-Mar-18 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, "Vishay"), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. (c) 2017 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED Revision: 08-Feb-17 1 Document Number: 91000