PRELIMINARY Product Specification 100m (OM4) 100G Ethernet CFP4 Optical Transceiver FTLC9141RENM PRODUCT FEATURES * Hot-pluggable CFP4 form factor * Supports 103.1Gb/s aggregate bit rate * Power dissipation < 4W * RoHS-6 compliant (lead-free) * Commercial case temperature range of 0C to 70C * Single 3.3V power supply APPLICATIONS * Maximum link length of 100m on OM4 Multimode Fiber (MMF) * * 4x25Gb/s 850mm VCSEL-based transmitter * 4x25G electrical interface * Single MPO12 receptacle * MDIO management interface 100GBASE-SR4 100G Ethernet Finisar's FTLC9141RENM 100G CFP4 transceiver modules are designed for use in 100 Gigabit Ethernet links over multimode fiber. They are compliant with the CFP4 MSA1 and IEEE 802.3ba 100GBASE-SR42. Digital diagnostics functions are available via the MDIO interface, as specified by the CFP MSA and Finisar Application Note AN-20xx5. The transceiver is RoHS-6 compliant and lead-free per Directive 2011/65/EU3, and Finisar Application Note AN-20384. PRODUCT SELECTION FTLC9141RENM R: E: N: M: 100G Ethernet maximum bit rate (103.1Gb/s) 4x25G parallel optics Bail type release MPO receptacle Finisar Corporation - 8-Apr-15 Rev. A4 PRELIMINARY Finisar Confidential Page 1 FTLC9141RENM PRELIMINARY Product Specification - April 2015 I. Pin Descriptions Per CFP MSA1. Pins views from the top. 56 55 Top Row GND TX3n 1 2 Bottom Row 3.3V_GND 3.3V_GND 54 TX3p 3 3.3V 53 GND 4 3.3V 52 TX2n 5 3.3V 51 TX2p 6 3.3V 50 GND 7 3.3V_GND 49 TX1n 8 3.3V_GND 48 TX1p 9 VND_IO_A 47 GND 10 VND_IO_B 46 TX0n 11 TX_DIS 45 TX0p 12 RX_LOS 44 GND 13 GLB_ALRMn 43 {REFCLKn} 14 MOD_LOPWR 42 {REFCLKp} 15 MOD_ABS 41 GND 16 MOD_RSTn 40 RX3n 17 MDC 39 RX3p 18 MDIO 38 GND 19 PRTADR0 37 RX2n 20 PRTADR1 36 RX2p 21 PRTADR2 35 GND 22 VND_IO_C 34 RX1n 23 VND_IO_D 33 RX1p 24 VND_IO_E 32 GND 25 GND 31 RX0n 26 {MCLKn} 30 RX0p 27 {MCLKp} 29 GND 28 GND Finisar Corporation - 8-Apr-15 Rev. A4 PRELIMINARY Finisar Confidential Page 2 FTLC9141RENM PRELIMINARY Product Specification - April 2015 Bottom Row Pin Descriptions PIN # 1 2 3 4 5 6 7 8 9 10 11 12 Name I/O 3.3V_GND 3.3V_GND 3.3V 3.3V 3.3V 3.3V 3.3V_GND 3.3V_GND VND_IO_A VND_IO_B TX_DIS RX_LOS I/O I/O I O 13 GLB_ALRMn O 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 MOD_LOPWR MOD_ABS MOD_RSTn MDC MDIO PRTADR0 PRTADR1 PRTADR2 VND_IO_C VND_IO_D VND_IO_E GND MCLKn MCLKp GND I O I I/O I I I I I/O I/O I/O Logic Description 3.3V Module Supply Voltage Return Ground, internally connected to Signal Ground 3.3V Module Supply Voltage Return Ground, internally connected to Signal Ground 3.3V Module Supply Voltage 3.3V Module Supply Voltage 3.3V Module Supply Voltage 3.3V Module Supply Voltage 3.3V Module Supply Voltage Return Ground, internally connected to Signal Ground 3.3V Module Supply Voltage Return Ground, internally connected to Signal Ground Module Vendor I/O A. Do Not Connect! Module Vendor I/O B. Do Not Connect! LVCMOS w/ PUR Transmitter Disable for all lanes, "1" or NC = transmitter disabled, "0" = transmitter enabled LVCMOS Receiver Loss of Optical Signal, "1": low optical signal, "0": normal condition Global Alarm. "0": alarm condition in any MDIO Alarm register, "1": no alarm condition, Open Drain, LVCMOS Pull Up Resistor on Host LVCMOS w/ PUR Module Low Power Mode. "1" or NC: module in low power (safe) mode, "0": power-on enabled GND Module Absent. "1" or NC: module absent, "0": module present, Pull Up Resistor on Host LVCMOS w/ PDR Module Reset. "0" resets the module, "1" or NC = module enabled, Pull Down Resistor in Module 1.2V CMOS Management Data I/O bi-directional data (electrical specs as per 802.3ae and ba) 1.2V CMOS Management Data Clock (electrical specs as per 802.3ae and ba) 1.2V CMOS MDIO Physical Port address bit 0 1.2V CMOS MDIO Physical Port address bit 1 1.2V CMOS MDIO Physical Port address bit 2 Module Vendor I/O C. Do Not Connect! Module Vendor I/O D. Do Not Connect! Module Vendor I/O E. Do Not Connect! Monitor Clock Monitor Clock Finisar Corporation - 8-Apr-15 Rev. A4 PRELIMINARY Finisar Confidential Page 3 FTLC9141RENM PRELIMINARY Product Specification - April 2015 II. Absolute Maximum Ratings Module performance is not guaranteed beyond the operating range (see Section VI). Exceeding the limits below may damage the transceiver module permanently. Parameter Maximum Supply Voltage Storage Temperature Case Operating Temperature Relative Humidity Receiver Damage Threshold, per Lane Symbol Vcc TS TOP RH PRdmg Min -0.5 -40 -5 15 5.5 Typ Max 4.0 85 75 85 Unit V C C % dBm Ref. Max 3.4 TBD 4 Unit V A W Ref. 25.78 Gb/s mV ps ps UI mV 2 Gb/s mV ps ps UI mV 2 1 Notes: 1. Non-condensing. III. Electrical Characteristics (EOL, TOP = 0 to 70 C, VCC = 3.2 to 3.4 Volts) Parameter Supply Voltage Supply Current Module total power Transmitter Signaling rate per lane Input differential impedance Differential data input swing per lane Data input rise time tolerance Data input rise time tolerance Electrical input eye mask definition Receiver Signaling rate per lane Differential data output swing per lane Data output rise time Data output fall time Electrical output eye mask definition Power Supply Noise Tolerance Symbol Vcc Icc P Rin Vin,pp tr tf {X1, X2} {Y1, Y2} Min 3.2 Typ CAUI-4 as being defined by IEEE 802.3bm 25.78 Vout,pp tr tf {X1, X2} {Y1, Y2} Vrip CAUI-4 as being defined by IEEE 802.3bm 1 TBD Notes: 1. Maximum total power value is specified across the full temperature and voltage range. 2. +/- 100ppm FTLC9141RENM Clocking Signals Clock Name Status I/O Value REFCLK Not Required I Optional MCLK Supported O N/A Finisar Corporation - 8-Apr-15 Rev. A4 PRELIMINARY Finisar Confidential Page 4 FTLC9141RENM PRELIMINARY Product Specification - April 2015 IV. Optical Characteristics (EOL, TOP = 0 to 70C, VCC = 3.2 to 3.4 Volts) Parameter Transmitter Signaling Speed per Lane Center wavelength RMS Spectral Width Average Launch Power per Lane Transmit OMA per Lane Difference in Power between any two lanes [OMA] Peak Power per Lane Launch Power [OMA] minus TDP per Lane TDP per Lane Optical Extinction Ratio Optical Return Loss Tolerance Encircled Flux Average launch power of OFF transmitter, per lane Relative Intensity Noise Transmitter eye mask definition {X1, X2, X3, Y1, Y2, Y3} Receiver Signaling Speed per Lane Center wavelength Damage Threshold Average Receive Power per Lane Receive Power (OMA) per Lane Symbol Min Max Unit Ref. 25.78 860 1 SW TXPx TxOMA DPx Gb/s nm nm dBm dBm dB PPx P-TDP dBm dBm 25.78 840 TDP ER ORL FLX Typ 100GBASE-SR4 as being defined by IEEE 802.3bm RIN dBm dB dB dBm dBm dB/Hz 25.78 25.78 DT RXPx RxOM A SRS GBd nm dBm dBm dBm 2 Stressed Receiver Sensitivity (OMA) dBm per Lane Back to Back Receiver Sensitivity RxSens dBm (OMA) per Lane Peak Power, per lane PPx dBm 100GBASE-SR4 as being defined Receiver Reflectance Rfl dB by IEEE 802.3bm Vertical eye closure penalty, per lane dB Stressed eye J2 jitter, per Lane UI Stressed eye J9 jitter, per Lane UI OMA of each aggressor lane dBm Receiver jitter tolerance [OMA], per dBm Lane Rx jitter tolerance: Jitter frequency kHz, UI and p-p amplitude kHz, UI LOS De-Assert LOSD dBm LOS Assert LOSA dBm LOS Hysteresis dB Notes: 1. Transmitter consists of 4 lasers operating at a maximum speed of 25.78Gb/s each. 2. Receiver consists of 4 photodetectors operating at a maximum speed of 25.78Gb/s each. Finisar Corporation - 8-Apr-15 Rev. A4 PRELIMINARY Finisar Confidential Page 5 FTLC9141RENM PRELIMINARY Product Specification - April 2015 V. General Specifications Parameter Symbol Min Typ Bit Rate (all wavelengths combined) BR Bit Error Ratio BER Maximum Supported Distances Fiber Type OM3 MMF Lmax1 OM4 MMF Lmax2 Notes: 1. Supports 100GBASE-SR4 per IEEE 802.3xx. 2. Tested with a 231 - 1 PRBS. 3. Requires KR4 FEC on the host to achieve maximum link distance. VI. Max 103.1 10-12 Units Gb/s Ref. 1 2 70 100 m m 3 3 Environmental Specifications Finisar FTLC9141 CFP4 transceivers have a commercial operating case temperature range of 0C to +70C. They can support temporary excursions to case temperatures of -5C and +75C without permanent damage (see Section II). Parameter Case Operating Temperature Storage Temperature VII. Symbol Top Tsto Min 0 -40 Typ Max 70 85 Units C C Ref. Regulatory Compliance Finisar FTLC9141 CFP4 transceivers are Class 1 Laser Products. They are certified per the following standards: Feature Agency Standard Laser Eye Safety Laser Eye Safety Electrical Safety Electrical Safety FDA/CDRH CDRH 21 CFR 1040 and Laser Notice 50 TUV EN 60825-1: 2007 IEC 60825-2: 2004+A1+A2 EN 60950 TBD CLASS 3862.07 CLASS 3862.87 TBD TUV UL/CSA Certificate Number 9210176 TBD Copies of the referenced certificates will be available at Finisar upon request. Complies with FDA performance standards for laser products except for deviations pursuant to Laser Notice No. 50, dated June 24, 2007. Finisar Corporation - 8-Apr-15 Rev. A4 PRELIMINARY Finisar Confidential Page 6 FTLC9141RENM PRELIMINARY Product Specification - April 2015 VIII. Digital Diagnostics Functions FTLC9141 CFP4 transceivers support the MDIO-based diagnostics interface specified by the CFP MSA1. See Finisar Application Note AN-20xx (TBD). IX. Memory Contents Per the CFP MSA1. See Finisar Application Note AN-20xx (TBD). X. Host PCB Layout and Bezel Recommendations Per CFP MSA Hardware Specification for CFP41. Finisar Corporation - 8-Apr-15 Rev. A4 PRELIMINARY Finisar Confidential Page 7 FTLC9141RENM PRELIMINARY Product Specification - April 2015 XI. Mechanical Specifications Finisar FTLC9141 CFP4 transceivers are compatible with the CFP MSA specification for CFP4 pluggable form factor modules. Figure 1. FTLC9141RENM Mechanical Dimensions. Finisar Corporation - 8-Apr-15 Rev. A4 PRELIMINARY Finisar Confidential Page 8 FTLC9141RENM PRELIMINARY Product Specification - April 2015 Figure 3. Standard Product Label XII. References 1. CFP4 Hardware Specification and CFP MSA Management Interface Specifications (MIS), Rev 2.4.; CFP MSA, www.cfp-msa.org 2. IEEE 802.3bm, PMD Type 100GBASE-SR4. 3. Directive 2011/65/EU of the European Parliament and of the Council, "on the restriction of the use of certain hazardous substances in electrical and electronic equipment," July 1, 2011. 4. "Application Note AN-2038: Finisar Implementation Of RoHS Compliant Transceivers", Finisar Corporation, January 21, 2005. 5. Application Note AN-20xx (TBD), Finisar Corporation. Finisar Corporation - 8-Apr-15 Rev. A4 PRELIMINARY Finisar Confidential Page 9 FTLC9141RENM PRELIMINARY Product Specification - April 2015 XIII. Revision History Revision Date A1 8/22/2012 A2 9/12/2013 A3 6/30/2014 A4 4/8/2015 Description * Preliminary document released. * Added monitor clock support; updated maximum power dissipation specification to 3.5W; added product photo. * Updated maximum power dissipation specification to 4W; added maximum link distance on OM3 MMF; added CDRH number; added product label. * Updated operating temperature range, RoHS reference, and new Finisar logo on the label. For More Information: Finisar Corporation 1389 Moffett Park Drive Sunnyvale, CA 94089-1133 Tel. 1-408-548-1000 Fax 1-408-541-6138 sales@finisar.com www.finisar.com Finisar Corporation - 8-Apr-15 Rev. A4 PRELIMINARY Finisar Confidential Page 10