STA339BW 2.1-channel high-efficiency digital audio system Features Wide voltage supply range - 5 V to 26 V (operating range) - 30 V (absolute maximum rating) 3 power output configurations - 2 channels of ternary PWM (stereo mode) (2 x 20 W into 8 at 18 V) - 3 channels - left, right using binary and LFE using ternary PWM (2.1 mode) (2 x 9 W + 1 x 20 W into 2 x 4 , 1 x 8 at 18 V) - 2 channels of ternary PWM (2 x 20 W) + stereo lineout ternary 2.1 channels of 24-bit FFX(R) 100 dB SNR and dynamic range Selectable 32 to 192 kHz input sample rates I2C control with selectable device address Digital gain/attenuation +48 dB to -80 dB with 0.5 dB/step resolution Soft volume update with programmable ratio Individual channel and master gain/attenuation Two independent DRC configurable as a dual-band anti-clipper (B2DRC) or as independent limiters/compressors EQ-DRC for DRC based on filtered signals Dedicated LFE processing for bass boosting with 0.5 dB/step resolution Audio presets: - 15 preset crossover filters - 5 preset anti-clipping modes - Preset night-time listening mode Individual channel and master soft/hard mute Table 1. PowerSSO-36 (slug down) Independent channel volume and DSP bypass Automatic zero-detect mute Automatic invalid input-detect mute 2-channel I2S input data interface Input and output channel mapping Up to 8 user-programmable biquads per channel with 28-bit resolution 3 coefficient banks for EQ presets storing with fast recall via I2C interface Bass/treble tones and de-emphasis control Selectable high-pass filter for DC blocking Advanced AM interference frequency switching and noise suppression modes Selectable high- or low-bandwidth noise-shaping topologies Variable max power correction for lower full-power THD Selectable clock input ratio 96 kHz internal processing sample rate, 24 to 28-bit precision Thermal overload and short-circuit protection embedded Video apps: 576 * fS input mode supported Fully compatible with STA339BWS. Device summary Order code Package Packaging STA339BW PowerSSO-36 slug down Tube STA339BWTR PowerSSO-36 slug down Tape and reel August 2010 Doc ID 15251 Rev 5 1/77 www.st.com 77 Contents STA339BW Contents 1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 1.1 2 3 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Pin connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 2.1 Connection diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 2.2 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Electrical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 3.1 Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 3.2 Thermal data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 3.3 Recommended operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 3.4 Electrical specifications for the digital section . . . . . . . . . . . . . . . . . . . . . 15 3.5 Electrical specifications for the power section . . . . . . . . . . . . . . . . . . . . . 16 3.6 Power on/off sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 3.7 Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 3.7.1 Functional pin definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 4 Processing data paths . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 5 I2C bus specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 5.1 5.1.1 Data transition or change . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 5.1.2 Start condition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 5.1.3 Stop condition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 5.1.4 Data input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 5.2 Device addressing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 5.3 Write operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 5.4 2/77 Communication protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 5.3.1 Byte write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 5.3.2 Multi-byte write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Read operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 5.4.1 Current address byte read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 5.4.2 Current address multi-byte read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 5.4.3 Random address byte read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Doc ID 15251 Rev 5 STA339BW 6 Contents 5.4.4 Random address multi-byte read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 5.4.5 Write mode sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 5.4.6 Read mode sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Register description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 6.1 6.2 6.3 6.4 6.5 Configuration register A (addr 0x00) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 6.1.1 Master clock select . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 6.1.2 Interpolation ratio select . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 6.1.3 Thermal warning recovery bypass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 6.1.4 Thermal warning adjustment bypass . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 6.1.5 Fault detect recovery bypass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Configuration register B (addr 0x01) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 6.2.1 Serial audio input interface format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 6.2.2 Serial data interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 6.2.3 Serial data first bit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 6.2.4 Delay serial clock enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 6.2.5 Channel input mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Configuration register C (addr 0x02) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 6.3.1 FFX power output mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 6.3.2 FFX compensating pulse size register . . . . . . . . . . . . . . . . . . . . . . . . . . 33 6.3.3 Overcurrent warning detect adjustment bypass . . . . . . . . . . . . . . . . . . . 34 Configuration register D (addr 0x03) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 6.4.1 High-pass filter bypass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 6.4.2 De-emphasis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 6.4.3 DSP bypass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 6.4.4 Post-scale link . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 6.4.5 Biquad coefficient link . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 6.4.6 Dynamic range compression/anti-clipping bit . . . . . . . . . . . . . . . . . . . . 35 6.4.7 Zero-detect mute enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 6.4.8 Submix mode enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Configuration register E (addr 0x04) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 6.5.1 Max power correction variable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 6.5.2 Max power correction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 6.5.3 Noise-shaper bandwidth selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 6.5.4 AM mode enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 6.5.5 PWM speed mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 6.5.6 Distortion compensation variable enable . . . . . . . . . . . . . . . . . . . . . . . . 37 Doc ID 15251 Rev 5 3/77 Contents STA339BW 6.6 6.7 6.8 6.9 6.10 6.5.7 Zero-crossing volume enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 6.5.8 Soft volume update enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Configuration register F (addr 0x05) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 6.6.1 Output configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 6.6.2 Invalid input detect mute enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 6.6.3 Binary output mode clock loss detection . . . . . . . . . . . . . . . . . . . . . . . . 44 6.6.4 LRCK double trigger protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 6.6.5 Auto EAPD on clock loss . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 6.6.6 IC power down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 6.6.7 External amplifier power down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Volume control registers (addr 0x06 - 0x0A) . . . . . . . . . . . . . . . . . . . . . . 45 6.7.1 Mute/line output configuration register . . . . . . . . . . . . . . . . . . . . . . . . . . 45 6.7.2 Master volume register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 6.7.3 Channel 1 volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 6.7.4 Channel 2 volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 6.7.5 Channel 3 / line output volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Audio preset registers (addr 0x0B and 0x0C) . . . . . . . . . . . . . . . . . . . . . 47 6.8.1 Audio preset register 1 (addr 0x0B) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 6.8.2 Audio preset register 2 (addr 0x0C) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 6.8.3 AM interference frequency switching . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 6.8.4 Bass management crossover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Channel configuration registers (addr 0x0E - 0x10) . . . . . . . . . . . . . . . . . 49 6.9.1 Tone control bypass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 6.9.2 EQ bypass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 6.9.3 Volume bypass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 6.9.4 Binary output enable registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 6.9.5 Limiter select . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 6.9.6 Output mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 Tone control register (addr 0x11) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 6.10.1 6.11 4/77 Tone control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 Dynamic control registers (addr 0x12 - 0x15) . . . . . . . . . . . . . . . . . . . . . 51 6.11.1 Limiter 1 attack/release rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 6.11.2 Limiter 1 attack/release threshold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 6.11.3 Limiter 2 attack/release rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 6.11.4 Limiter 2 attack/release threshold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 6.11.5 Limiter 1 Extended attack threshold (addr 0x32) . . . . . . . . . . . . . . . . . . 55 Doc ID 15251 Rev 5 STA339BW Contents 6.12 6.11.6 Limiter 1 Extended release threshold (addr 0x33) . . . . . . . . . . . . . . . . . 55 6.11.7 Limiter 2 Extended attack threshold (addr 0x34 . . . . . . . . . . . . . . . . . . ) 56 6.11.8 Limiter 2 Extended release threshold (addr 0x35) . . . . . . . . . . . . . . . . . 56 User-defined coefficient control registers (addr 0x16 - 0x26) . . . . . . . . . . 56 6.12.1 Coefficient address register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 6.12.2 Coefficient b1 data register bits 23:16 . . . . . . . . . . . . . . . . . . . . . . . . . . 56 6.12.3 Coefficient b1 data register bits 15:8 . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 6.12.4 Coefficient b1 data register bits 7:0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 6.12.5 Coefficient b2 data register bits 23:16 . . . . . . . . . . . . . . . . . . . . . . . . . . 57 6.12.6 Coefficient b2 data register bits 15:8 . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 6.12.7 Coefficient b2 data register bits 7:0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 6.12.8 Coefficient a1 data register bits 23:16 . . . . . . . . . . . . . . . . . . . . . . . . . . 57 6.12.9 Coefficient a1 data register bits 15:8 . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 6.12.10 Coefficient a1 data register bits 7:0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 6.12.11 Coefficient a2 data register bits 23:16 . . . . . . . . . . . . . . . . . . . . . . . . . . 57 6.12.12 Coefficient a2 data register bits 15:8 . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 6.12.13 Coefficient a2 data register bits 7:0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 6.12.14 Coefficient b0 data register bits 23:16 . . . . . . . . . . . . . . . . . . . . . . . . . . 58 6.12.15 Coefficient b0 data register bits 15:8 . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 6.12.16 Coefficient b0 data register bits 7:0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 6.12.17 Coefficient write/read control register . . . . . . . . . . . . . . . . . . . . . . . . . . 58 6.12.18 User-defined EQ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 6.12.19 Prescale . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 6.12.20 Postscale . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 6.12.21 Overcurrent postscale . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 6.13 Variable max power correction registers (addr 0x27 - 0x28) . . . . . . . . . . 63 6.14 Variable distortion compensation registers (addr 0x29 - 0x2A) . . . . . . . . 63 6.15 Fault detect recovery constant registers (addr 0x2B - 0x2C) . . . . . . . . . . 64 6.16 Device status register (addr 0x2D) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 6.17 EQ coefficients and DRC configuration register (addr 0x31) . . . . . . . . . . 65 6.18 Extended configuration register (addr 0x36) . . . . . . . . . . . . . . . . . . . . . . 65 6.18.1 Dual-band DRC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 6.18.2 EQ DRC mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 6.18.3 Extended post scale range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 6.18.4 Extended attack rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 6.18.5 Extended BIQUAD selector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 Doc ID 15251 Rev 5 5/77 Contents 7 STA339BW 6.19 EQ soft volume configuration registers (addr 0x37 - 0x38) . . . . . . . . . . . 69 6.20 DRC RMS filter coefficients (addr 0x39 - 0x3E) . . . . . . . . . . . . . . . . . . . . 70 Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 7.1 Application scheme for power supplies . . . . . . . . . . . . . . . . . . . . . . . . . . 71 7.2 PLL filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 7.3 Typical output configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 8 Package thermal characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 9 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 10 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76 6/77 Doc ID 15251 Rev 5 STA339BW List of figures List of figures Figure 1. Figure 2. Figure 3. Figure 4. Figure 5. Figure 6. Figure 7. Figure 8. Figure 9. Figure 10. Figure 11. Figure 12. Figure 13. Figure 14. Figure 15. Figure 16. Figure 17. Figure 18. Figure 19. Figure 20. Figure 21. Figure 22. Figure 23. Figure 24. Figure 25. Figure 26. Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Pin connection PowerSSO-36 (top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Power-on sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Power-off sequence for pop-free turn-off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Test circuit 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Test circuit 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Left and right processing part 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Processing part 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Write mode sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Read mode sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 OCFG = 00 (default value) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 OCFG = 01 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 OCFG = 10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 OCFG = 11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Output mapping scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 2.0 channels (OCFG = 00) PWM slots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 2.1 channels (OCFG = 01) PWM slots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 2.1 channels (OCFG = 10) PWM slots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Basic limiter and volume flow diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 B2DRC scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 EQDRC scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 Application diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 Output configuration for stereo BTL mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 Double-layer PCB with 2 copper ground areas and 16 via holes . . . . . . . . . . . . . . . . . . . 73 PowerSSO-36 power derating curve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 PowerSSO-36 slug down outline drawing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 Doc ID 15251 Rev 5 7/77 List of tables STA339BW List of tables Table 1. Table 2. Table 3. Table 4. Table 5. Table 6. Table 7. Table 8. Table 9. Table 10. Table 11. Table 12. Table 13. Table 14. Table 15. Table 16. Table 17. Table 18. Table 19. Table 20. Table 21. Table 22. Table 23. Table 24. Table 25. Table 26. Table 27. Table 28. Table 29. Table 30. Table 31. Table 32. Table 33. Table 34. Table 35. Table 36. Table 37. Table 38. Table 39. Table 40. Table 41. Table 42. Table 43. Table 44. Table 45. Table 46. Table 47. Table 48. 8/77 Device summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Thermal data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Recommended operating condition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Electrical specifications - digital section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Electrical specifications - power section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Functional pin definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Register summary. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Master clock select . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Input sampling rates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Internal interpolation ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 IR bit settings as a function of input sample rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Thermal warning recovery bypass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Thermal warning adjustment bypass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Fault detect recovery bypass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Serial audio input interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Serial data first bit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Supported serial audio input formats for MSB-first (SAIFB = 0) . . . . . . . . . . . . . . . . . . . . . 30 Supported serial audio input formats for LSB-first (SAIFB = 1) . . . . . . . . . . . . . . . . . . . . . 31 Delay serial clock enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Channel input mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 FFX power output mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Output modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 FFX compensating pulse size bits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Compensating pulse size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Overcurrent warning bypass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 High-pass filter bypass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 De-emphasis. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 DSP bypass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Post-scale link. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Biquad coefficient link . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Dynamic range compression/anti-clipping bit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Zero-detect mute enable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Submix mode enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Max power correction variable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Max power correction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Noise-shaper bandwidth selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 AM mode enable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 PWM speed mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Distortion compensation variable enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Zero-crossing volume enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Soft volume update enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Output configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Output configuration engine selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Invalid input detect mute enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Binary output mode clock loss detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 LRCK double trigger protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Doc ID 15251 Rev 5 STA339BW Table 49. Table 50. Table 51. Table 52. Table 53. Table 54. Table 55. Table 56. Table 57. Table 58. Table 59. Table 60. Table 61. Table 62. Table 63. Table 64. Table 65. Table 66. Table 67. Table 68. Table 69. Table 70. Table 71. Table 72. Table 73. Table 74. Table 75. Table 76. Table 77. Table 78. Table 79. Table 80. Table 81. Table 82. Table 83. Table 84. Table 85. Table 86. List of tables Auto EAPD on clock loss . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 IC power down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 External amplifier power down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Line output configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Master volume offset as a function of MV[7:0] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Channel volume as a function of CxV[7:0] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Audio preset gain compression/limiters selection for AMGC[3:2] = 00. . . . . . . . . . . . . . . . 47 AM interference frequency switching bits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Audio preset AM switching frequency selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Bass management crossover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Bass management crossover frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Tone control bypass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 EQ bypass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Binary output enable registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 Channel limiter mapping as a function of CxLS bits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 Channel output mapping as a function of CxOM bits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 Tone control boost/cut as a function of BTC and TTC bits . . . . . . . . . . . . . . . . . . . . . . . . . 51 Limiter attack rate as a function of LxA bits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Limiter release rate as a function of LxR bits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Limiter attack threshold as a function of LxAT bits (AC mode) . . . . . . . . . . . . . . . . . . . . . . 54 Limiter release threshold as a function of LxRT bits (AC mode). . . . . . . . . . . . . . . . . . . . . 54 Limiter attack threshold as a function of LxAT bits (DRC mode) . . . . . . . . . . . . . . . . . . . . 55 Limiter release threshold as a as a function of LxRT bits (DRC mode) . . . . . . . . . . . . . . . 55 RAM block for biquads, mixing, scaling and bass management. . . . . . . . . . . . . . . . . . . . . 62 Status register bits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 EQ RAM select . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 Anti-clipping and DRC preset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 Anti-clipping selection for AMGC[3:2] = 01 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 Post scale setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 Extended attack rate setup for limiter 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 Extended attack rate setup for limiter 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 De-emphasis filter setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 Bass filter setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 Treble filter setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 Soft volume (increasing) setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 Soft volume (decreasing) setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 PowerSSO-36 slug down dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76 Doc ID 15251 Rev 5 9/77 Description 1 STA339BW Description The STA339BW is an integrated solution of digital audio processing, digital amplifier control, and FFX-power output stage, thereby creating a high-power single-chip FFX(R) solution comprising high-quality, high-efficiency, all digital amplification. STA339BW is based on FFX (fully flexible amplification) processor, a STMicroelectronics proprietary technology. FFX is the evolution and the enlargement of the ST ternary technology: the new processor can be configured to work in ternary, binary, binary differential and phase shift PWM modulation schemes. STA339BW contains the ternary, binary and binary differential implementations, a subset of the full capability of the FFX processor. The STA339BW is part of the Sound TerminalTM family that provides full digital audio streaming to the speaker, offering cost effectiveness, low power dissipation and sound enrichment. The STA339BW power section consists of four independent half bridges. These can be configured via digital control to operate in different modes. 2.1 channels can be provided by two half bridges and a single full bridge, providing up to 2 x 9 W + 1 x 20 W of power output. Two channels can be provided by two full bridges, providing up to 2 x 20 W of power. The IC can also be configured as 2.1 channels with 2 x 20 W provided by the device and external power for FFX power drive. Also provided in the STA339BW are a full assortment of digital processing features. This includes up to 8 programmable 28-bit biquads (EQ) per channel and bass/treble tone control. Available presets enable a time-to-market advantage by substantially reducing the amount of software development needed for certain functions. This includes audio preset volume loudness, preset volume curves and preset EQ settings. There are also new advanced AM radio interference reduction modes. Dual band DRC dynamically equalizes the system to provide speaker linear frequency response regardless output power level. This feature independently processes the two bands, controlling, dynamically, the output power level in each band and so providing a better sound quality. The serial audio data input interface accepts all possible formats, including the popular I2S format. Three channels of FFX processing are provided. This high-quality conversion from PCM audio to FFX PWM switching waveform provides over 100 dB SNR and dynamic range. 10/77 Doc ID 15251 Rev 5 STA339BW 1.1 Description Block diagram Figure 1. Block diagram I2C Protection current/thermal 2 I S interface Volume control Channel 1A Channel 1B Logic Power control FFX Channel 2A Regulators Channel 2B PLL Bias Digital DSP Power Doc ID 15251 Rev 5 11/77 Pin connections STA339BW 2 Pin connections 2.1 Connection diagram Figure 2. Pin connection PowerSSO-36 (top view) GND_SUB 1 36 VDD_DIG SA 2 35 GND_DIG TEST_MODE 3 34 SCL VSS 4 33 SDA VCC_REG 5 32 INT_LINE OUT2B 6 31 RESET GND2 7 30 SDI VCC2 8 29 LRCKI OUT2A 9 28 BICKI OUT1B 10 27 XTI VCC1 11 26 GND_PLL GND1 12 25 FILTER_PLL OUT1A 13 24 VDD_PLL GND_REG 14 23 PWRDN VDD 15 22 GND_DIG CONFIG 16 21 VDD_DIG OUT3B / FFX3B 17 20 TWARN / OUT4A OUT3A / FFX3A 18 19 EAPD / OUT4B D05AU1638 2.2 Pin description Table 2. Pin description Pin 12/77 Type Name Description 1 GND GND_SUB Substrate ground 2 I SA I2C select address (pull-down) 3 I TEST_MODE This pin must be connected to ground (pull-down) 4 I/O VSS Internal reference at VCC - 3.3 V 5 I/O VCC_REG Internal VCC reference 6 O OUT2B Output half bridge 2B 7 GND GND2 Power negative supply 8 Power VCC2 Power positive supply 9 O OUT2A Output half bridge 2A 10 O OUT1B Output half bridge 1B Doc ID 15251 Rev 5 STA339BW Pin connections Table 2. Pin description (continued) Pin Type Name Description 11 Power VCC1 Power positive supply 12 GND GND1 Power negative supply 13 O OUT1A Output half bridge 1A 14 GND GND_REG Internal ground reference 15 Power VDD Internal 3.3 V reference voltage 16 I CONFIG Paralleled mode command 17 O OUT3B / FFX3B PWM out Ch3B / external bridge driver 18 O OUT3A / FFX3A PWM out Ch3A / external bridge driver 19 O EAPD / OUT4B Power down for external bridge / PWM out Ch4B 20 I/O TWARN / OUT4A Thermal warning from external bridge (pull-up when input) / PWM out Ch4A 21 Power VDD_DIG Digital supply voltage 22 GND GND_DIG Digital ground 23 I PWRDN Power down (pull-up) 24 Power VDD_PLL Positive supply for PLL 25 I FILTER_PLL Connection to PLL filter 26 GND GND_PLL Negative supply for PLL 27 I XTI PLL input clock 28 I BICKI I2S serial clock 29 I LRCKI I2S left/right clock 30 I SDI I2S serial data channels 1 and 2 31 I RESET Reset (pull-up) 32 O INT_LINE Fault interrupt 33 I/O SDA I2C serial data 34 I SCL I2C serial clock 35 GND GND_DIG Digital ground 36 Power VDD_DIG Digital supply voltage Doc ID 15251 Rev 5 13/77 Electrical specifications STA339BW 3 Electrical specifications 3.1 Absolute maximum ratings Table 3. Absolute maximum ratings Symbol VCC Parameter Power supply voltage (VCCxA, VCCxB) Max Unit - 30 V VDD_DIG Digital supply voltage -0.3 - 4 V VDD_PLL PLL supply voltage -0.3 - 4 V Top Operating junction temperature -20 - 150 C Tstg Storage temperature -40 - 150 C Stresses beyond those listed in Table 3 above may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "Recommended operating conditions" are not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. In the real application, power supplies with nominal values rated within the recommended operating conditions, may experience some rising beyond the maximum operating conditions for a short time when no or very low current is sinked (amplifier in mute state). In this case the reliability of the device is guaranteed, provided that the absolute maximum ratings are not exceeded. Thermal data Table 4. Thermal data Parameter Rth j-case Min Thermal resistance junction-case (thermal pad) (1) Typ Max Unit - - 1.5 C/W - - - C/W Rth j-amb Thermal resistance junction-ambient Tth-sdj Thermal shut-down junction temperature - 150 - C Tth-w Thermal warning temperature - 130 - C Tth-sdh Thermal shut-down hysteresis - 20 - C 1. See Section 8: Package thermal characteristics on page 73 for details. 14/77 Typ -0.3 Warning: 3.2 Min Doc ID 15251 Rev 5 STA339BW 3.3 Electrical specifications Recommended operating conditions Table 5. Recommended operating condition Symbol VCC Min Power supply voltage (VCCxA, VCCxB) Typ Max Unit 5 - 26 V VDD_DIG Digital supply voltage 2.7 3.3 3.6 V VDD_PLL PLL supply voltage 2.7 3.3 3.6 V -20 - 70 C Tamb 3.4 Parameter Ambient temperature Electrical specifications for the digital section Table 6. Symbol Electrical specifications - digital section Parameter Conditions Min Typ Max Unit Iil Low-level input current without pull-up/down device Vi = 0 V -10 1 10 A Iih High-level input current without pull-up/down device Vi = VDD_DIG = 3.6 V -10 1 10 A Vil Low-level input voltage - - - Vih High-level input voltage - Vol Low-level output voltage Iol = 2 mA Voh High-level output voltage Ioh = 2 mA Ipu Pull-up/down current - Rpu Equivalent pull-up/down resistance - Doc ID 15251 Rev 5 0.8 * VDD_DIG 0.8 * - 0.2 * VDD_DIG 0.4 * VDD_DIG V V V - - V 25 66 125 A - 50 - k VDD_DIG 15/77 Electrical specifications 3.5 STA339BW Electrical specifications for the power section The specifications given in this section are valid for the operating conditions: VCC = 18 V, f = 1 kHz, fsw = 384 kHz, Tamb = 25 C and RL = 8 , unless otherwise specified. Table 7. Electrical specifications - power section Symbol Parameter Conditions Min Typ Max THD = 1% - 16 - THD = 10% - 20 - THD = 1% - 4 - THD = 10% - 5 - Output power BTL Unit W Po Output power SE W RdsON Power Pchannel/Nchannel MOSFET (total ld = 1.5 A bridge) - 180 250 m gP Power Pchannel RdsON matching ld = 1.5 A 95 - - % gN Power Nchannel RdsON matching ld = 1.5 A 95 - - % Idss Power Pchannel/Nchannel leakage VCC = 20 V ILDT IHDT Low current dead time (static) High current dead time (dynamic) - - 10 A Resistive load(1) - 8 15 ns Iload = 1.5 A(1) - 15 30 ns load(1) - 10 18 ns tr Rise time Resistive tf Fall time Resistive load(1) - 10 18 ns VCC Supply voltage operating voltage - 5 - 26 V Supply current from VCC in power down PWRDN = 0 - 0.1 1 mA Supply current from VCC in operation PCM Input signal = 60 dBfs, Switching frequency = 384 kHz, No LC filters - 52 60 mA - 55 70 mA (2) 3.0 3.8 4.0 A Ivcc Ivdd Supply current FFX processing (reference Internal clock = only) 49.152 MHz Ilim Overcurrent limit Isc Short circuit protection Hi-Z output 3.8 4.8 - A UVL Undervoltage protection - - 3.5 4.3 V tmin Output minimum pulse width No load 20 30 60 ns DR Dynamic range - - 100 - dB Signal to noise ratio, ternary mode A-weighted - 100 - dB Signal to noise ratio binary mode - - 90 - dB Power supply rejection ratio FFX stereo mode, <5 kHz VRIPPLE = 1 V RMS Audio input = dither only - 80 - dB SNR PSSR 16/77 Doc ID 15251 Rev 5 STA339BW Table 7. Electrical specifications Electrical specifications - power section (continued) Symbol THD+N XTALK Parameter Conditions Min Typ Max Unit Total harmonic distortion + noise FFX stereo mode, Po = 1 W f = 1 kHz - 0.2 - % Crosstalk FFX stereo mode, <5 kHz One channel driven at 1 W Other channel measured - 80 - dB Peak efficiency, FFX mode Po = 2 x 20 W into 8 - 90 - Peak efficiency,binary modes Po = 2 x 9 W into 4 + 1 x 20 W into 8 % 87 - 1. Refer to Figure 5: Test circuit 1. 2. Limit current if the register (OCRB par 6.1.3.3) overcurrent warning detect adjustment bypass is enabled. When disabled refer to the Isc. Doc ID 15251 Rev 5 17/77 Electrical specifications 3.6 STA339BW Power on/off sequence Figure 3. Power-on sequence Note: no specific VCC and VDD_DIG turn-on sequence is required VCC Don't care VDD_Dig XTI Don't care Reset TC TR I2C Don't care CMD0 CMD1 CMD2 PWDN TR = minimum time between XTI master clock stable and Reset removal: 1 ms TC = minimum time between Reset removal and I2C program, sequence start: 1ms Note: The definition of a stable clock is when fmax - fmin < 1 MHz. Section 6.2.3 on page 30 gives information on setting up the I2S interface. Figure 4. Power-off sequence for pop-free turn-off Note: no specific VCC and VDD_DIG turn-off sequence is required VCC Don't care VDD_Dig XTI Soft Mute Reg. 0x07 Data 0xFE Don't care Don't care FE Soft EAPD Reg. 0x05 Bit 7 = 0 18/77 Doc ID 15251 Rev 5 Don't care STA339BW Electrical specifications 3.7 Testing 3.7.1 Functional pin definition Table 8. Pin name PWRDN TWARN EAPD Functional pin definition Number Logic value 0 Low consumption 1 Normal operation 0 A temperature warning is indicated by the external power stage 1 Normal operation 0 Low consumption for power stage All internal regulators are switched off 1 Normal operation 23 20 19 Figure 5. IC status Test circuit 1 OUTxY Vcc (3/4)Vcc Low current dead time = MAX(DTr, DTf) (1/2)Vcc (1/4)Vcc +Vcc t DTr Duty cycle = 50% OUTxY INxY DTf Rload = 8 + vdc = Vcc/2 - gnd Figure 6. Test circuit 2 High current dead time for Bridge application = ABS(DTout(A)-DTin(A))+ABS(DTOUT(B)-DTin(B)) +VCC Duty cycle=A Duty cycle=B DTout(A) Q2 Q1 DTin(A) INxA Iout Q3 DTout(B) Rload = 4 OUTxA 10 470nF 10 470nF 470nF OUTxB Iout Q4 Duty cycle A and B: Fixed to have DC output current of Iout in the direction shown in figure Doc ID 15251 Rev 5 DTin(B) INxB D06AU1651_00 19/77 Processing data paths 4 STA339BW Processing data paths The whole processing chain is composed of two consecutive sections. In the first one dual-channel processing is implemented, as described below. Then each channel is fed into the post-mixing block where there is a choice of processing, either the dual-band DRC is disabled or it is enabled. When B2DRC is disabled a third channel, typically used in 2.1 output configuration and with cross-over filters enabled, is used. When B2DRC is enabled the 2.0 output configuration with cross-over filters for defining the cutoff frequency of the two bands is used. The first section, Figure 7, begins with a 2x oversampling FIR filter allowing a 2 * fs audio processing. Then a selectable high-pass filter removes the DC level (enabled if HFB = 0). The channel 1 and 2 processing chain can include up to 8 filters, depending on the selected configuration (bits BQL, BQ5, BQ6, BQ7 and XO[3:0]). By default, four independent filters per channel are enabled, plus the preconfigured deemphasis, bass and treble controls (BQL = 0, BQ5 = 0, BQ6 = 0, BQ7 = 0). If the coefficient sets are linked (BQL = 1) then it is possible to use the de-emphasis, bass and treble filter in a user defined configuration (provided the relevant BQx bits are set to 1). In other words both channels use the same processing coefficients and can have up to 7 filters each. Note that if BQL = 0 the BQx bits are ignored and the 5th, 6th and 7th filters are configured as de-emphasis, bass and treble controls, respectively. Moreover the common 8th filter, from the subsequent processing section, can be available on both channels (provided the pre-defined cross-over frequencies are not used, XO[3:0] = 0, and the dual-band DRC is not used). In the second section, mixing and crossover filters are available. If B2DRC is not enabled (lower schematic in Figure 8) they are fully user-programmable and allow a third channel (2.1 outputs) to be generated. Alternatively, in B2DRC mode (upper schematic in Figure 8), those blocks will be used to split the sub-band and define the cutoff frequencies of the two bands. A prescaler and a final post scaler allow full control over the signal dynamics before and after, respectively, the filtering stages. A mixer function is also available. Figure 7. Left and right processing part 1 Sampling frequency = fs Sampling frequency = 2 * fs x2 FIR x2 over FIR sampling over Pre-scale PreScale If BQ5=1 and BQL=1 Biquad #5 Hi-pass Pass filter Filter Biquad #1 If HPB=0 Biquad #2 Biquad #3 Biquad #4 User-defined filters De-Emph. If DEMP=0 From I2S input interface If DSPB=0 and C1EQBP=0 x2 FIR x2 over FIR sampling over Pre-scale PreScale Hi-pass Pass Filter filter If HPB=0 Biquad #1 Biquad #2 Biquad #3 User-defined filters If DSPB=0 and C2EQBP=0 20/77 Doc ID 15251 Rev 5 If BQ5=1 and BQL=1 Biquad #5 Biquad #4 De-Emph. If DEMP=0 If BQ6=1 IF BQ7=1 and BQL=1 and BQL=1 Biquad Biquad #6 #7 Bass Treble L L If C1TCB=0 BTC: bass boost/cut TTC: treble boost/cut If BQ6=1 IF BQ7=1 and BQL=1 and BQL=1 Biquad Biquad #6 #7 Bass Treble If C2TCB=0 BTC: bass boost/cut TTC: treble boost/cut L R STA339BW Processing data paths Figure 8. Processing part 2 Dual-band DRC enabled Ch3 Volume L C1Mx1 C1Mx1 = 0x7FFFFF Hi-Pass B2DRC XO Filter Hi-pass + filter R - C1Mx2 C1Mx2= 0x00000 C2Mx1 C2Mx1= 0x000000 Hi-Pass XO 2DRC BFilter Hi-pass filter + C2Mx2 C2Mx2= 0x7FFFFF - Ch1 + Volume + Volume Ch2 C3Mx1 C3Mx1= 0x40000 Ch3 + Volume DRC2 Vol And DRC1 Limiter + Post scale Post-scale DRC1 + Post scale Post-scale DRC2 C3Mx2 C3Mx2= 0x400000 B2DRC Enabled User-defined mix coefficients Crossover frequency determined by XO setting User-defined if XO = 0000 Dual-band DRC disabled L C1Mx1 Channel 1/2 Hi-Pass XO Biquad #5 Filter -------------Hi-pass XO filter + R C1Mx2 Volume Vol And and Limiter Post scale Post-scale Volume Vol And and Limiter Post scale Post-scale Volume Vol And and Limiter Post scale Post-scale C2Mx1 Channel 1/2 Hi-Pass XO Biquad Filter#5 -------------Hi-pass XO filter + C2Mx2 C3Mx1 Channel 3 Lo-Pass XO Biquad Filter -------------Low-pass XO filter + C3Mx2 B2DRC Disabled User-defined mix coefficients Crossover frequency determined by XO setting User defined if XO = 0000 Doc ID 15251 Rev 5 21/77 I2C bus specification 5 STA339BW I2C bus specification The STA339BW supports the I2C protocol via the input ports SCL and SDA_IN (master to slave) and the output port SDA_OUT (slave to master). This protocol defines any device that sends data on to the bus as a transmitter and any device that reads the data as a receiver. The device that controls the data transfer is known as the master and the other as the slave. The master always starts the transfer and provides the serial clock for synchronization. The STA339BW is always a slave device in all of its communications. It can operate at up to 400 kb/s (fast-mode bit rate). The STA339BW I2C interface is a slave only interface. 5.1 Communication protocol 5.1.1 Data transition or change Data changes on the SDA line must only occur when the SCL clock is low. SDA transition while the clock is high is used to identify a START or STOP condition. 5.1.2 Start condition START is identified by a high to low transition of the data bus SDA signal while the clock signal SCL is stable in the high state. A START condition must precede any command for data transfer. 5.1.3 Stop condition STOP is identified by low to high transition of the data bus SDA signal while the clock signal SCL is stable in the high state. A STOP condition terminates communication between STA339BW and the bus master. 5.1.4 Data input During the data input the STA339BW samples the SDA signal on the rising edge of clock SCL. For correct device operation the SDA signal must be stable during the rising edge of the clock and the data can change only when the SCL line is low. 5.2 Device addressing To start communication between the master and the STA339BW, the master must initiate with a start condition. Following this, the master sends onto the SDA line 8-bits (MSB first) corresponding to the device select address and read or write mode. The seven most significant bits are the device address identifiers, corresponding to the I2C bus definition. In the STA339BW the I2C interface has two device addresses depending on the SA port configuration, 0x38 when SA = 0, and 0x3A when SA = 1. The eighth bit (LSB) identifies read or write operation RW, this bit is set to 1 in read mode and to 0 for write mode. After a START condition the STA339BW identifies on the bus the device address and if a match is found, acknowledges the identification on the SDA bus during the 9th bit time. The byte following the device identification byte is the internal space address. 22/77 Doc ID 15251 Rev 5 I2C bus specification STA339BW 5.3 Write operation Following the START condition the master sends a device select code with the RW bit set to 0. The STA339BW acknowledges this and the writes for the byte of internal address. After receiving the internal byte address the STA339BW again responds with an acknowledgement. 5.3.1 Byte write In the byte write mode the master sends one data byte, this is acknowledged by the STA339BW. The master then terminates the transfer by generating a STOP condition. 5.3.2 Multi-byte write The multi-byte write modes can start from any internal address. The master generating a STOP condition terminates the transfer. 5.4 Read operation 5.4.1 Current address byte read Following the START condition the master sends a device select code with the RW bit set to 1. The STA339BW acknowledges this and then responds by sending one byte of data. The master then terminates the transfer by generating a STOP condition. 5.4.2 Current address multi-byte read The multi-byte read modes can start from any internal address. Sequential data bytes are read from sequential addresses within the STA339BW. The master acknowledges each data byte read and then generates a STOP condition terminating the transfer. 5.4.3 Random address byte read Following the START condition the master sends a device select code with the RW bit set to 0. The STA339BW acknowledges this and then the master writes the internal address byte. After receiving, the internal byte address the STA339BW again responds with an acknowledgement. The master then initiates another START condition and sends the device select code with the RW bit set to 1. The STA339BW acknowledges this and then responds by sending one byte of data. The master then terminates the transfer by generating a STOP condition. 5.4.4 Random address multi-byte read The multi-byte read modes could start from any internal address. Sequential data bytes are read from sequential addresses within the STA339BW. The master acknowledges each data byte read and then generates a STOP condition terminating the transfer. Doc ID 15251 Rev 5 23/77 I2C bus specification 5.4.5 STA339BW Write mode sequence Figure 9. Write mode sequence ACK BYTE WRITE DEV-ADDR ACK DATA IN RW START STOP ACK MULTIBYTE WRITE DEV-ADDR ACK ACK SUB-ADDR ACK DATA IN DATA IN RW START 5.4.6 ACK SUB-ADDR STOP Read mode sequence Figure 10. Read mode sequence ACK CURRENT ADDRESS READ DEV-ADDR NO ACK DATA RW START STOP ACK RANDOM ADDRESS READ DEV-ADDR RW RW= ACK HIGH START SEQUENTIAL CURRENT READ ACK SUB-ADDR DEV-ADDR ACK DEV-ADDR START RW ACK DATA NO ACK DATA STOP ACK DATA NO ACK DATA STOP START ACK SEQUENTIAL RANDOM READ DEV-ADDR START 24/77 ACK SUB-ADDR RW ACK DEV-ADDR START ACK DATA RW Doc ID 15251 Rev 5 ACK DATA NO ACK DATA STOP STA339BW Register description 6 Register description Table 9. Register summary Addr Name D7 D6 D5 D4 D3 D2 D1 D0 0x00 CONFA FDRB TWAB TWRB IR1 IR0 MCS2 MCS1 MCS0 0x01 CONFB C2IM C1IM DSCKE SAIFB SAI3 SAI2 SAI1 SAI0 0x02 CONFC OCRB Reserved CSZ3 CSZ2 CSZ1 CSZ0 OM1 OM0 0x03 CONFD SME ZDE DRC BQL PSL DSPB DEMP HPB 0x04 CONFE SVE ZCE DCCV PWMS AME NSBW MPC MPCV 0x05 CONFF EAPD PWDN ECLE LDTE BCLE IDE OCFG1 OCFG0 0x06 MUTE/LOC LOC1 LOC0 C3M C2M C1M MMUTE 0x07 MVOL MV7 MV6 MV5 MV4 MV3 MV2 MV1 MV0 0x08 C1VOL C1V7 C1V6 C1V5 C1V4 C1V3 C1V2 C1V1 C1V0 0x09 C2VOL C2V7 C2V6 C2V5 C2V4 C2V3 C2V2 C2V1 C2V0 0x0A C3VOL C3V7 C3V6 C3V5 C3V4 C3V3 C3V2 C3V1 C3V0 0x0B AUTO1 AMGC1 AMGC0 0x0C AUTO2 XO1 XO0 AMAM1 AMAM0 AMAME 0x0D AUTO3 0x0E C1CFG C1OM1 C1OM0 C1LS1 C1LS0 C1BO C1VBP C1EQBP C1TCB 0x0F C2CFG C2OM1 C2OM0 C2LS1 C2LS0 C2BO C2VBP C2EQBP C2TCB 0x10 C3CFG C3OM1 C3OM0 C3LS1 C3LS0 C3BO C3VBP 0x11 TONE TTC3 TTC2 TTC1 TTC0 BTC3 BTC2 BTC1 BTC0 0x12 L1AR L1A3 L1A2 L1A1 L1A0 L1R3 L1R2 L1R1 L1R0 0x13 L1ATRT L1AT3 L1AT2 L1AT1 L1AT0 L1RT3 L1RT2 L1RT1 L1RT0 0x14 L2AR L2A3 L2A2 L2A1 L2A0 L2R3 L2R2 L2R1 L2R0 0x15 L2ATRT L2AT3 L2AT2 L2AT1 L2AT0 L2RT3 L2RT2 L2RT1 L2RT0 0x16 CFADDR CFA5 CFA4 CFA3 CFA2 CFA1 CFA0 0x17 B1CF1 C1B23 C1B22 C1B21 C1B20 C1B19 C1B18 C1B17 C1B16 0x18 B1CF2 C1B15 C1B14 C1B13 C1B12 C1B11 C1B10 C1B9 C1B8 0x19 B1CF3 C1B7 C1B6 C1B5 C1B4 C1B3 C1B2 C1B1 C1B0 0x1A B2CF1 C2B23 C2B22 C2B21 C2B20 C2B19 C2B18 C2B17 C2B16 0x1B B2CF2 C2B15 C2B14 C2B13 C2B12 C2B11 C2B10 C2B9 C2B8 0x1C B2CF3 C2B7 C2B6 C2B5 C2B4 C2B3 C2B2 C2B1 C2B0 0x1D A1CF1 C3B23 C3B22 C3B21 C3B20 C3B19 C3B18 C3B17 C3B16 0x1E A1CF2 C3B15 C3B14 C3B13 C3B12 C3B11 C3B10 C3B9 C3B8 0x1F A1CF3 C3B7 C3B6 C3B5 C3B4 C3B3 C3B2 C3B1 C3B0 Reserved XO3 XO2 Reserved Reserved AMAM2 Reserved Reserved Doc ID 15251 Rev 5 Reserved 25/77 Register description Table 9. Addr STA339BW Register summary (continued) Name D7 D6 D5 D4 D3 D2 D1 D0 0x20 A2CF1 C4B23 C4B22 C4B21 C4B20 C4B19 C4B18 C4B17 C4B16 0x21 A2CF2 C4B15 C4B14 C4B13 C4B12 C4B11 C4B10 C4B9 C4B8 0x22 A2CF3 C4B7 C4B6 C4B5 C4B4 C4B3 C4B2 C4B1 C4B0 0x23 B0CF1 C5B23 C5B22 C5B21 C5B20 C5B19 C5B18 C5B17 C5B16 0x24 B0CF2 C5B15 C5B14 C5B13 C5B12 C5B11 C5B10 C5B9 C5B8 0x25 B0CF3 C5B7 C5B6 C5B5 C5B4 C5B3 C5B2 C5B1 C5B0 0x26 CFUD RA R1 WA W1 0x27 MPCC1 MPCC15 MPCC14 MPCC13 MPCC12 MPCC11 MPCC10 MPCC9 MPCC8 0x28 MPCC2 MPCC7 MPCC6 MPCC5 MPCC4 MPCC3 MPCC2 MPCC1 MPCC0 0x29 DCC1 DCC15 DCC14 DCC13 DCC12 DCC11 DCC10 DCC9 DCC8 0x2A DCC2 DCC7 DCC6 DCC5 DCC4 DCC3 DCC2 DCC1 DCC0 0x2B FDRC1 FDRC15 FDRC14 FDRC13 FDRC12 FDRC11 FDRC10 FDRC9 FDRC8 0x2C FDRC2 FDRC7 FDRC6 FDRC5 FDRC4 FDRC3 FDRC2 FDRC1 FDRC0 0x2D STATUS PLLUL FAULT UVFAULT OVFAULT OCFAULT OCWARN TFAULT TWARN 0x2E Reserved Reserved RO1BACT R5BACT R4BACT R3BACT R2BACT R1BACT 0x2F Reserved Reserved R01BEND R5BEND R4BEND R3BEND R2BEND R1BEND 0x30 Reserved R5BBAD R4BBAD R3BBAD R2BBAD R1BBAD 0x31 EQCFG XOB AMGC3 AMGC2 Reserved SEL1 SEL0 0x32 EATH1 EATHEN1 EATH1[6] EATH1[5] EATH1[4] EATH1[3] EATH1[2] EATH1[1] EATH1[0] 0x33 ERTH1 ERTHEN1 ERTH1[6] ERTH1[5] ERTH1[4] ERTH1[3] ERTH1[2] ERTH1[1] ERTH1[0] 0x34 EATH2 EATHEN2 EATH2[6] EATH2[5] EATH2[4] EATH2[3] EATH2[2] EATH2[1] EATH2[0] 0x35 ERTH2 ERTHEN2 ERTH2[6] ERTH2[5] ERTH2[4] ERTH2[3] ERTH2[2] ERTH2[1] ERTH2[0] 0x36 CONFX MDRC[1] MDRC[0] PS48DB XAR1 XAR2 BQ5 BQ6 BQ7 0x37 SVCA Reserved SVUPE SVUP[4] SVUP[3] SVUP[2] SVUP[1] SVUP[0] 0x38 SVCB Reserved SVDWE SVDW[4] SVDW[3] SVDW[2] SVDW[1] SVDW[0] 0x39 RMS0A R_C0[23] R_C0[22] R_C0[21] R_C0[20] R_C0[19] R_C0[18] R_C0[17] R_C0[16] 0x3A RMS0B R_C0[15] R_C0[14] R_C0[13] R_C0[12] R_C0[11] R_C0[10] R_C0[9] R_C0[8] 0x3B RMS0C R_C0[7] R_C0[6] R_C0[5] R_C0[4] R_C0[3] R_C0[2] R_C0[1] R_C0[0] 0x3C RMS1A R_C1[23] R_C1[22] R_C1[21] R_C1[20] R_C1[19] R_C1[18] R_C1[17] R_C1[16] 0x3D RMS1B R_C1[15] R_C1[14] R_C1[13] R_C1[12] R_C1[11] R_C1[10] R_C1[9] R_C1[8] 0x3E RMS1C R_C1[7] R_C1[6] R_C1[5] R_C1[4] R_C1[3] R_C1[2] R_C1[1] R_C1[0] 26/77 Reserved Reserved Reserved Doc ID 15251 Rev 5 STA339BW 6.1 6.1.1 Register description Configuration register A (addr 0x00) D7 D6 D5 D4 D3 D2 D1 D0 FDRB TWAB TWRB IR1 IR0 MCS2 MCS1 MCS0 0 1 1 0 0 0 1 1 Master clock select Table 10. Master clock select Bit R/W RST Name 0 R/W 1 MCS0 1 R/W 1 MCS1 2 R/W 0 MCS2 Description Selects the ratio between the input I2S sample frequency and the input clock. The STA339BW supports sample rates of 32 kHz, 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz, and 192 kHz. Therefore the internal clock is: z 32.768 MHz for 32 kHz z 45.1584 MHz for 44.1 kHz, 88.2 kHz, and 176.4 kHz z 49.152 MHz for 48 kHz, 96 kHz, and 192 kHz The external clock frequency provided to the XTI pin must be a multiple of the input sample frequency (fs). The relationship between the input clock and the input sample rate is determined by both the MCSx and the IR (input rate) register bits. The MCSx bits determine the PLL factor generating the internal clock and the IR bit determines the oversampling ratio used internally. Table 11. Input sampling rates Input sample rate fs (kHz) - IR - MCS[2:0] 101 100 011 010 001 000 32, 44.1, 48 00 576 * fs 128 * fs 256 * fs 384 * fs 512 * fs 768 * fs 88.2, 96 01 NA 64 * fs 128 * fs 192 * fs 256 * fs 384 * fs 176.4, 192 1X NA 32 * fs 64 * fs 96 * fs 128 * fs 192 * fs Doc ID 15251 Rev 5 27/77 Register description 6.1.2 STA339BW Interpolation ratio select Table 12. Bit 4:3 Internal interpolation ratio R/W R/W RST 00 Name Description Selects internal interpolation ratio based on input I2S sample frequency IR [1:0] The STA339BW has variable interpolation (oversampling) settings such that internal processing and FFX output rates remain consistent. The first processing block interpolates by either 2-times or 1-time (pass-through) or provides a 2-times downsample. The oversampling ratio of this interpolation is determined by the IR bits. Table 13. IR bit settings as a function of input sample rate Input sample rate fs (kHz) 6.1.3 IR 1st stage interpolation ratio 32 00 2 times oversampling 44.1 00 2 times oversampling 48 00 2 times oversampling 88.2 01 Pass-through 96 01 Pass-through 176.4 10 2 times downsampling 192 10 2 times downsampling Thermal warning recovery bypass Table 14. Bit 5 Thermal warning recovery bypass R/W R/W RST 1 Name Description 0: Thermal warning recovery enabled 1: Thermal warning recovery disabled TWRB If the thermal warning adjustment is enabled (TWAB = 0), then the thermal warning recovery determines if the -3 dB output limit is removed when thermal warning is negative. If TWRB = 0 and TWAB = 0, then when a thermal warning disappears the -3 dB output limit is removed and the gain is added back to the system. If TWRB = 1 and TWAB = 0, then when a thermal warning disappears the -3 dB output limit remains until TWRB is changed to zero or the device is reset. 6.1.4 Thermal warning adjustment bypass Table 15. Bit 6 Thermal warning adjustment bypass R/W R/W RST 1 Name TWAB Description 0: Thermal warning adjustment enabled 1: Thermal warning adjustment disabled The on-chip STA339BW power output block provides feedback to the digital controller using inputs to the power control block. Input TWARN is used to indicate a thermal warning 28/77 Doc ID 15251 Rev 5 STA339BW Register description condition. When TWARN is asserted (set to 0) for a period of time greater than 400 ms, the power control block forces a -3 dB output limit (determined by TWOCL in the coefficient RAM) to the modulation limit in an attempt to eliminate the thermal warning condition. Once the thermal warning output limit adjustment is applied, it remains in this state until reset, unless FDRB = 0. 6.1.5 Fault detect recovery bypass Table 16. Bit Fault detect recovery bypass R/W 7 R/W RST 0 Name Description 0: fault detect recovery enabled 1: fault detect recovery disabled FDRB The on-chip STA339BW power output block provides feedback to the digital controller using inputs to the power control block. The FAULT input is used to indicate a fault condition (either overcurrent or thermal). When FAULT is asserted (set to 0), the power control block attempts a recovery from the fault by asserting the tri-state output (setting it to 0 which directs the power output block to begin recovery), holds it at 0 for period of time in the range of 0.1 ms to 1 second as defined by the fault-detect recovery constant register (FDRC registers 0x2B0x2C), then toggles it back to 1. This sequence is repeated as log as the fault indication exists. This feature is enabled by default but can be bypassed by setting the FDRB control bit to 1. 6.2 6.2.1 Configuration register B (addr 0x01) D7 D6 D5 D4 D3 D2 D1 D0 C2IM C1IM DSCKE SAIFB SAI3 SAI2 SAI1 SAI0 1 0 0 0 0 0 0 0 Serial audio input interface format Table 17. Bit Serial audio input interface R/W RST Name 0 R/W 0 SAI0 1 R/W 0 SAI1 2 R/W 0 SAI2 3 R/W 0 SAI3 Description Determines the interface format of the input serial digital audio interface. Doc ID 15251 Rev 5 29/77 Register description 6.2.2 STA339BW Serial data interface The STA339BW audio serial input was designed to interface with standard digital audio components and to accept a number of serial data formats. STA339BW always acts as slave when receiving audio input from standard digital audio components. Serial data for two channels is provided using three inputs: left/right clock LRCKI, serial clock BICKI, and serial data 1 and 2 SDI12. The SAI bits (D3 to D0) and the SAIFB bit (D4) are used to specify the serial data format. The default serial data format is I2S, MSB-first. Available formats are shown in the tables and figure that follow. 6.2.3 Serial data first bit Table 18. Serial data first bit SAIFB Format 0 MSB-first 1 LSB-first Table 19. Supported serial audio input formats for MSB-first (SAIFB = 0) BICKI SAI [3:0] SAIFB Interface format 0000 0 I2S 15-bit data 0001 0 Left/right-justified 16-bit data 0000 0 I2S 16 to 23-bit data 0001 0 Left-justified 16 to 24-bit data 0010 0 Right-justified 24-bit data 0110 0 Right-justified 20-bit data 1010 0 Right-justified 18-bit data 1110 0 Right-justified 16-bit data 0000 0 I2S 16 to 24-bit data 0001 0 Left-justified 16 to 24-bit data 0010 0 Right-justified 24-bit data 0110 0 Right-justified 20-bit data 1010 0 Right-justified 18-bit data 1110 0 Right-justified 16-bit data 32 * fs 48 * fs 64 * fs 30/77 Doc ID 15251 Rev 5 STA339BW Register description Table 20. Supported serial audio input formats for LSB-first (SAIFB = 1) BICKI SAI [3:0] SAIFB Interface format 1100 1 I2S 15-bit data 1110 1 Left/right-justified 16-bit data 0100 1 I2S 23-bit data 0100 1 I2S 20-bit data 1000 1 I2S 18-bit data 1100 1 LSB first I2S 16-bit data 0001 1 Left-justified 24-bit data 0101 1 Left-justified 20-bit data 1001 1 Left-justified 18-bit data 1101 1 Left-justified 16-bit data 0010 1 Right-justified 24-bit data 0110 1 Right-justified 20-bit data 1010 1 Right-justified 18-bit data 1110 1 Right-justified 16-bit data 0000 1 I2S 24-bit data 0100 1 I2S 20-bit data 1000 1 I2S 18-bit data 1100 1 LSB first I2S 16-bit data 0001 1 Left-justified 24-bit data 0101 1 Left-justified 20-bit data 1001 1 Left-justified 18-bit data 1101 1 Left-justified 16-bit data 0010 1 Right-justified 24-bit data 0110 1 Right-justified 20-bit data 1010 1 Right-justified 18-bit data 1110 1 Right-justified 16-bit data 32 * fs 48 * fs 64 * fs To make the STA339BW work properly, the serial audio interface LRCKI clock must be synchronous to the PLL output clock. It means that: the frequency of PLL clock / frequency of LRCKI = N 4 cycles, where N depends on the settings in Table 13 on page 28 the PLL must be locked. If these two conditions are not met, and bit IDE of register address 0x05 is set to 1, the STA339BW immediately mutes the I2S PCM data out (provided to the processing block) and it freezes any active processing task. To avoid any audio side effects (like pop noise), it is strongly recommended to soft mute any audio streams flowing into STA339BW data path before the desynchronization event Doc ID 15251 Rev 5 31/77 Register description STA339BW happens. At the same time any processing related to the I2C configuration should be issued only after the serial audio interface and the internal PLL are synchronous again. Note: Any mute or volume change causes some delay in the completion of the I2C operation due to the soft volume feature. The soft volume phase change must be finished before any clock desynchronization. 6.2.4 Delay serial clock enable Table 21. Bit 5 6.2.5 Delay serial clock enable R/W R/W RST 0 Name DSCKE Description 0: No serial clock delay 1: Serial clock delay by 1 core clock cycle to tolerate anomalies in some I2S master devices Channel input mapping Table 22. Bit Channel input mapping R/W RST Name Description 6 R/W 0 C1IM 0: Processing channel 1 receives Left I2S Input 1: Processing channel 1 receives Right I2S Input 7 R/W 1 C2IM 0: Processing channel 2 receives Left I2S Input 1: Processing channel 2 receives Right I2S Input Each channel received via I2S can be mapped to any internal processing channel via the Channel Input Mapping registers. This allows for flexibility in processing. The default settings of these registers map each I2S input channel to its corresponding processing channel. 32/77 Doc ID 15251 Rev 5 STA339BW 6.3 6.3.1 Register description Configuration register C (addr 0x02) D7 D6 D5 D4 D3 D2 D1 D0 OCRB Reserved CSZ3 CSZ2 CSZ1 CSZ0 OM1 OM0 1 0 0 1 1 1 1 1 FFX power output mode Table 23. Bit FFX power output mode R/W RST Name 0 R/W 1 OM0 1 R/W 1 OM1 Description Selects configuration of FFX output. The FFX power output mode selects how the FFX output timing is configured. Different power devices use different output modes. Table 24. Output modes OM[1,0] 6.3.2 Output stage mode 00 Drop compensation 01 Discrete output stage - tapered compensation 10 Full power mode 11 Variable drop compensation (CSZx bits) FFX compensating pulse size register Table 25. Bit FFX compensating pulse size bits R/W RST Name 2 R/W 1 CSZ0 3 R/W 1 CSZ1 4 R/W 1 CSZ2 5 R/W 0 CSZ3 Table 26. Description When OM[1,0] = 11, this register determines the size of the FFX compensating pulse from 0 clock ticks to 15 clock periods. Compensating pulse size CSZ[3:0] Compensating pulse size 0000 0 ns (0 tick) compensating pulse size 0001 20 ns (1 tick) clock period compensating pulse size ... ... 1111 300 ns (15 tick) clock period compensating pulse size Doc ID 15251 Rev 5 33/77 Register description 6.3.3 STA339BW Overcurrent warning detect adjustment bypass Table 27. Bit Overcurrent warning bypass R/W 7 RST R/W 1 Name Description 0: overcurrent warning adjustment enabled 1: overcurrent warning adjustment disabled OCRB The OCWARN input is used to indicate an overcurrent warning condition. When OCWARN is asserted (set to 0), the power control block forces an adjustment to the modulation limit (default is -3 dB) in an attempt to eliminate the overcurrent warning condition. Once the overcurrent warning volume adjustment is applied, it remains in this state until reset is applied. The level of adjustment can be changed via the TWOCL (thermal warning / overcurrent limit) setting which is address 0x37 of the user defined coefficient RAM. 6.4 6.4.1 Configuration register D (addr 0x03) D7 D6 D5 D4 D3 D2 D1 D0 SME ZDE DRC BQL PSL DSPB DEMP HPB 0 1 0 0 0 0 0 0 High-pass filter bypass Table 28. Bit 0 High-pass filter bypass R/W R/W RST 0 Name Description Setting of one bypasses internal AC coupling digital high-pass filter HPB The STA339BW features an internal digital high-pass filter for the purpose of AC coupling. The purpose of this filter is to prevent DC signals from passing through a FFX amplifier. DC signals can cause speaker damage. When HPB = 0, this filter is enabled. 6.4.2 De-emphasis Table 29. Bit 1 6.4.3 De-emphasis R/W R/W RST 0 Name Description 0: No de-emphasis 1: Enable de-emphasis on all channels DEMP DSP bypass Table 30. Bit 2 DSP bypass R/W R/W RST 0 Name DSPB Description 0: Normal operation 1: Bypass of biquad and bass/treble functions Setting the DSPB bit bypasses the EQ function of the STA339BW. 34/77 Doc ID 15251 Rev 5 STA339BW 6.4.4 Register description Post-scale link Table 31. Bit 3 Post-scale link R/W R/W RST 0 Name Description 0: Each channel uses individual post-scale value 1: Each channel uses channel 1 post-scale value PSL Post-scale functionality can be used for power-supply error correction. For multi-channel applications running off the same power-supply, the post-scale values can be linked to the value of channel 1 for ease of use and update the values faster. 6.4.5 Biquad coefficient link Table 32. Bit 4 Biquad coefficient link R/W R/W RST 0 Name Description 0: Each channel uses coefficient values 1: Each channel uses channel 1 coefficient values BQL For ease of use, all channels can use the biquad coefficients loaded into the Channel-1 coefficient RAM space by setting the BQL bit to 1. Therefore, any EQ updates only have to be performed once. 6.4.6 Dynamic range compression/anti-clipping bit Table 33. Bit 5 Dynamic range compression/anti-clipping bit R/W R/W RST 0 Name Description 0: Limiters act in anti-clipping mode 1: Limiters act in dynamic range compression mode DRC Both limiters can be used in one of two ways, anti-clipping or dynamic range compression. When used in anti-clipping mode the limiter threshold values are constant and dependent on the limiter settings. In dynamic range compression mode the limiter threshold values vary with the volume settings allowing a nighttime listening mode that provides a reduction in the dynamic range regardless of the volume level. 6.4.7 Zero-detect mute enable Table 34. Bit 6 Zero-detect mute enable R/W R/W RST 1 Name ZDE Description Setting of 1 enables the automatic zero-detect mute Setting the ZDE bit enables the zero-detect automatic mute. The zero-detect circuit looks at the data for each processing channel at the output of the crossover (bass management) filter. If any channel receives 2048 consecutive zero value samples (regardless of fs) then that individual channel is muted if this function is enabled. Doc ID 15251 Rev 5 35/77 Register description 6.4.8 STA339BW Submix mode enable Table 35. Bit R/W 7 6.5 6.5.1 Submix mode enable R/W 0 Name Description 0: Sub Mix into Left/Right disabled 1: Sub Mix into Left/Right enabled SME Configuration register E (addr 0x04) D7 D6 D5 D4 D3 D2 D1 D0 SVE ZCE DCCV PWMS AME NSBW MPC MPCV 1 1 0 0 0 0 1 0 Max power correction variable Table 36. Bit 0 6.5.2 RST Max power correction variable R/W RST R/W 0 Name Description 0: Use standard MPC coefficient 1: Use MPCC bits for MPC coefficient MPCV Max power correction Table 37. Bit 1 Max power correction R/W RST R/W 1 Name Description Setting of 1 enables Power Bridge correction for THD reduction near maximum power output. MPC Setting the MPC bit turns on special processing that corrects the STA339BW power device at high power. This mode should lower the THD+N of a full FFX system at maximum power output and slightly below. If enabled, MPC is operational in all output modes except tapered (OM[1,0] = 01) and binary. When OCFG = 00, MPC will not effect channels 3 and 4, the lineout channels. 6.5.3 Noise-shaper bandwidth selection Table 38. Bit 2 36/77 R/W R/W Noise-shaper bandwidth selection RST 0 Name NSBW Description 1: Third order NS 0: Fourth order NS Doc ID 15251 Rev 5 STA339BW 6.5.4 Register description AM mode enable Table 39. Bit 3 R/W R/W AM mode enable RST 0 Name Description 0: Normal FFX operation. 1: AM reduction mode FFX operation AME STA339BW features aFFX processing mode that minimizes the amount of noise generated in frequency range of AM radio. This mode is intended for use when FFX is operating in a device with an AM tuner active. The SNR of the FFX processing is reduced to approximately 83 dB in this mode, which is still greater than the SNR of AM radio. 6.5.5 PWM speed mode Table 40. Bit 4 6.5.6 R/W R/W RST 0 Name Description 0: Normal speed (384 kHz) all channels 1: Odd speed (341.3 kHz) all channels PWMS Distortion compensation variable enable Table 41. Bit 5 6.5.7 PWM speed mode R/W R/W Distortion compensation variable enable RST 0 Name Description 0: Use preset DC coefficient 1: Use DCC coefficient DCCV Zero-crossing volume enable Table 42. Bit 6 R/W R/W Zero-crossing volume enable RST 1 Name Description 1: Volume adjustments only occur at digital zerocrossings 0: Volume adjustments occur immediately ZCE The ZCE bit enables zero-crossing volume adjustments. When volume is adjusted on digital zero-crossings no clicks are audible. 6.5.8 Soft volume update enable Table 43. Bit 7 R/W R/W Soft volume update enable RST 1 Name SVE Description 1: Volume adjustments ramp according to SVR settings 0: Volume adjustments occur immediately Doc ID 15251 Rev 5 37/77 Register description 6.6 6.6.1 STA339BW Configuration register F (addr 0x05) D7 D6 D5 D4 D3 D2 D1 D0 EAPD PWDN ECLE LDTE BCLE IDE OCFG1 OCFG0 0 1 0 1 1 1 0 0 Output configuration Table 44. Bit Output configuration R/W RST Name 0 R/W 0 OCFG0 1 R/W 0 OCFG1 Description Selects the output configuration Table 45. OCFG[1:0] Note: 38/77 Output configuration engine selection Output configuration Config pin 00 2 channel (full-bridge) power, 2 channel data-out: 1A/1B 1A/1B 2A/2B 2A/2B LineOut1 3A/3B LineOut2 4A/4B Line Out Configuration determined by LOC register 0 01 2(Half-Bridge).1(Full-Bridge) On-Board Power: 1A 1A Binary 0 2A 1B Binary 90 3A/3B 2A/2B Binary 45 1A/B 3A/B Binary 0 2A/B 4A/B Binary 90 0 10 2 Channel (Full-Bridge) Power, 1 Channel FFX: 1A/1B 1A/1B 2A/2B 2A/2B 3A/3B 3A/3B EAPDEXT and TWARNEXT Active 0 11 1 Channel Mono-Parallel: 3A 1A/1B w/ C3BO 45 3B 2A/2B w/ C3BO 45 1A/1B 3A/3B 2A/2B 4A/4B 1 To the left of the arrow is the processing channel. When using channel output mapping, any of the three processing channel outputs can be used for any of the three inputs. Doc ID 15251 Rev 5 STA339BW Register description Figure 11. OCFG = 00 (default value) Half Bridge OUT1A Channel 1 Half Bridge Half Bridge Half Bridge OUT1B OUT2A Channel 2 OUT2B OUT3A OUT3B LineOut 1 LPF OUT4A OUT4B LineOut 2 LPF Figure 12. OCFG = 01 Half Bridge Half Bridge Half Bridge Half Bridge Channel 1 OUT1A Channel 2 OUT1B OUT2A Channel 3 OUT2B Figure 13. OCFG = 10 Half Bridge OUT1A Channel 1 Half Bridge Half Bridge Half Bridge OUT1B OUT2A Channel 2 OUT2B OUT3A OUT3B Power Device Channel 3 EAPD Doc ID 15251 Rev 5 39/77 Register description STA339BW Figure 14. OCFG = 11 OUT1A Half Bridge OUT1B Half Bridge Channel 3 Half Bridge Half Bridge OUT2A OUT2B OUT3A OUT3B OUT4A OUT4B Channel 1 Channel 2 The STA339BW can be configured to support different output configurations. For each PWM output channel a PWM slot is defined. A PWM slot is always 1 / (8 * fs) seconds length. The PWM slot define the maximum extension for PWM rise and fall edge, that is, rising edge as far as the falling edge cannot range outside PWM slot boundaries. Figure 15. Output mapping scheme FFX1A OUT1A OUT1A OUT1B OUT1B FFX1 B FFX2 A FFX TM modulator FFX 2B FFX3 A OUT2A Power Bridge OUT2A FFX3B FFX4 A OUT2B OUT2B FFX 4B REMAP OUT3A OUT3B OUT4A OUT4B For each configuration the PWM signals from the digital driver are mapped in different ways to the power stage: 40/77 Doc ID 15251 Rev 5 STA339BW Register description 2.0 channels, two full bridges (OCFG = 00) z FFX1A -> OUT1A z FFX1B -> OUT1B z FFX2A -> OUT2A z FFX2B -> OUT2B z FFX3A -> OUT3A z FFX3B -> OUT3B z FFX4A -> OUT4A z FFX4B -> OUT4B z FFX1A/1B configured as ternary z FFX2A/2B configured as ternary z FFX3A/3B configured as lineout ternary z FFX4A/4B configured as lineout ternary On channel 3 line out (LOC bits = 00) the same data as channel 1 processing is sent. On channel 4 line out (LOC bits = 00) the same data as channel 2 processing is sent. In this configuration, volume control or EQ have no effect on channels 3 and 4. In this configuration the PWM slot phase is the following as shown in Figure 16. Figure 16. 2.0 channels (OCFG = 00) PWM slots OUT1A OUT1B OUT2A OUT2B OUT3A OUT3B OUT4A OUT4B Doc ID 15251 Rev 5 41/77 Register description STA339BW 2.1 channels, two half bridges + one full bridge (OCFG = 01) z FFX1A -> OUT1A z FFX2A -> OUT1B z FFX3A -> OUT2A z FFX3B -> OUT2B z FFX1A -> OUT3A z FFX1B -> OUT3B z FFX2A -> OUT4A z FFX2B -> OUT4B z FFX1A/1B configured as binary z FFX2A/2B configured as binary z FFX3A/3B configured as binary z FFX4A/4B is not used In this configuration, channel 3 has full control (volume, EQ, etc...). On OUT3/OUT4 channels the channel 1 and channel 2 PWM are replicated. In this configuration the PWM slot phase is the following as shown in Figure 17. Figure 17. 2.1 channels (OCFG = 01) PWM slots OUT1A OUT1B OUT2A OUT2B OUT3A OUT3B OUT4A OUT4B 42/77 Doc ID 15251 Rev 5 STA339BW Register description 2.1 channels, two fullbridge + one external full bridge (OCFG = 10) z FFX1A -> OUT1A z FFX1B -> OUT1B z FFX2A -> OUT2A z FFX2B -> OUT2B z FFX3A -> OUT3A z FFX3B -> OUT3B z EAPD -> OUT4A z TWARN -> OUT4B z FFX1A/1B configured as ternary z FFX2A/2B configured as ternary z FFX3A/3B configured as ternary z FFX4A/4B is not used In this configuration, channel 3 has full control (volume, EQ, etc...). On OUT4 channel the external bridge control signals are muxed. In this configuration the PWM slot phase is the following as shown in Figure 18. Figure 18. 2.1 channels (OCFG = 10) PWM slots OUT1A OUT1B OUT2A OUT2B OUT3A OUT3B Doc ID 15251 Rev 5 43/77 Register description 6.6.2 STA339BW Invalid input detect mute enable Table 46. Bit 2 Invalid input detect mute enable R/W R/W RST 1 Name Description Setting of 1 enables the automatic invalid input detect mute IDE Setting the IDE bit enables this function, which looks at the input I2S data and automatically mutes if the signals are perceived as invalid. 6.6.3 Binary output mode clock loss detection Table 47. Bit 3 Binary output mode clock loss detection R/W R/W RST 1 Name BCLE Description Binary output mode clock loss detection enable Detects loss of input MCLK in binary mode and will output 50% duty cycle. 6.6.4 LRCK double trigger protection Table 48. Bit 4 LRCK double trigger protection R/W R/W RST 1 Name LDTE Description LRCLK double trigger protection enable Actively prevents double trigger of LRCLK. 6.6.5 Auto EAPD on clock loss Table 49. Bit 5 Auto EAPD on clock loss R/W R/W RST 0 Name ECLE Description Auto EAPD on clock loss When active, issues a power device power down signal (EAPD) on clock loss detection. 6.6.6 IC power down Table 50. Bit 7 IC power down R/W R/W RST 1 Name PWDN Description 0: IC power down low-power condition 1: IC normal operation The PWDN register is used to place the IC in a low-power state. When PWDN is written as 0, the output begins a soft-mute. After the mute condition is reached, EAPD is asserted to power down the power-stage, then the master clock to all internal hardware expect the I2C block is gated. This places the IC in a very low power consumption state. 44/77 Doc ID 15251 Rev 5 STA339BW 6.6.7 Register description External amplifier power down Table 51. Bit External amplifier power down R/W 7 R/W RST 0 Name Description 0: External power stage power down active 1: Normal operation EAPD The EAPD register directly disables/enables the internal power circuitry. When EAPD = 0, the internal power section is placed on a low-power state (disabled). This register also controls the FFX4B/EAPD output pin when OCFG = 10. 6.7 Volume control registers (addr 0x06 - 0x0A) 6.7.1 Mute/line output configuration register D7 D6 LOC1 LOC0 0 0 Table 52. D5 D4 Reserved 0 D3 D2 D1 D0 C3M C2M C1M MMUTE 0 0 0 0 0 Line output configuration LOC[1:0] Line output configuration 00 Line output fixed - no volume, no EQ 01 Line output variable - CH3 volume effects line output, no EQ 10 Line output variable with EQ - CH3 volume effects line output Line output is only active when OCFG = 00. In this case LOC determines the line output configuration. The source of the line output is always the channel 1 and 2 inputs. 6.7.2 6.7.3 6.7.4 Master volume register D7 D6 D5 D4 D3 D2 D1 D0 MV7 MV6 MV5 MV4 MV3 MV2 MV1 MV0 1 1 1 1 1 1 1 1 Channel 1 volume D7 D6 D5 D4 D3 D2 D1 D0 C1V7 C1V6 C1V5 C1V4 C1V3 C1V2 C1V1 C1V0 0 1 1 0 0 0 0 0 Channel 2 volume D7 D6 D5 D4 D3 D2 D1 D0 C2V7 C2V6 C2V5 C2V4 C2V3 C2V2 C2V1 C2V0 0 1 1 0 0 0 0 0 Doc ID 15251 Rev 5 45/77 Register description 6.7.5 STA339BW Channel 3 / line output volume D7 D6 D5 D4 D3 D2 D1 D0 C3V7 C3V6 C3V5 C3V4 C3V3 C3V2 C3V1 C3V0 0 1 1 0 0 0 0 0 The Volume structure of the STA339BW consists of individual volume registers for each channel and a master volume register that provides an offset to each channels volume setting. The individual channel volumes are adjustable in 0.5 dB steps from +48 dB to 80 dB. As an example if C3V = 0x00 or +48 dB and MV = 0x18 or -12 dB, then the total gain for channel 3 = +36 dB. The master mute, when set to 1, mutes all channels at once, whereas the individual channel mutes (CxM) mutes only that channel. Both the master mute and the channel mutes provide a "soft mute" with the volume ramping down to mute in 4096 samples from the maximum volume setting at the internal processing rate (approximately 96 kHz). A "hard (instantaneous) mute" can be obtained by programming a value of 0xFF (255) to any channel volume register or the master volume register. When volume offsets are provided via the master volume register any channel whose total volume is less than -80 dB is muted. All changes in volume take place at zero-crossings when ZCE = 1 (Configuration register E (addr 0x04) on page 36) on a per channel basis as this creates the smoothest possible volume transitions. When ZCE = 0, volume updates occur immediately. Table 53. Master volume offset as a function of MV[7:0] MV[7:0] Volume offset from channel value 00000000 (0x00) 0 dB 00000001 (0x01) -0.5 dB 00000010 (0x02) -1 dB ... ... 01001100 (0x4C) -38 dB ... ... 11111110 (0xFE) -127.5 dB 11111111 (0xFF) Hard master mute Table 54. Channel volume as a function of CxV[7:0] CxV[7:0] 46/77 Volume 00000000 (0x00) +48 dB 00000001 (0x01) +47.5 dB 00000010 (0x02) +47 dB ... ... 01011111 (0x5F) +0.5 dB 01100000 (0x60) 0 dB Doc ID 15251 Rev 5 STA339BW Register description Table 54. Channel volume as a function of CxV[7:0] (continued) CxV[7:0] Volume 01100001 (0x61) -0.5 dB ... ... 11010111 (0xD7) -59.5 dB 11011000 (0xD8) -60 dB 11011001 (0xD9) -61 dB 11011010 (0xDA) -62 dB ... ... 11101100 (0xEC) -80 dB 11101101 (0xED) Hard channel mute ... ... 11111111 (0xFF) Hard channel mute 6.8 Audio preset registers (addr 0x0B and 0x0C) 6.8.1 Audio preset register 1 (addr 0x0B) D7 D6 Reserved 0 0 D5 D4 AMGC[1] AMGC[0] 0 0 D3 D2 D1 D0 0 0 Reserved 0 0 Using AMGC[3:0] bits, attack and release thresholds and rates are automatically configured to properly fit application specific configurations. AMGC[3:2] is defined in register EQ coefficients and DRC configuration register (addr 0x31) on page 65. The AMGC[1:0] bits behave in two different ways depending on the value of AMGC[3:2]. When this value is 00 then bits AMGC[1:0] are defined below in Table 55. Table 55. Audio preset gain compression/limiters selection for AMGC[3:2] = 00 AMGC[1:0] 6.8.2 Mode 00 User programmable GC 01 AC no clipping 2.1 10 AC limited clipping (10%) 2.1 11 DRC night-time listening mode 2.1 Audio preset register 2 (addr 0x0C) D7 D6 D5 D4 D3 D2 D1 D0 XO3 XO2 XO1 XO0 AMAM2 AMAM1 AMAM0 AMAME 0 0 0 0 0 0 0 0 Doc ID 15251 Rev 5 47/77 Register description 6.8.3 STA339BW AM interference frequency switching Table 56. Bit 0 AM interference frequency switching bits R/W R/W Table 57. RST Name 0 AMAME 48 kHz/96 kHz input fs 44.1 kHz/88.2 kHz input fs 000 0.535 MHz - 0.720 MHz 0.535 MHz - 0.670 MHz 001 0.721 MHz - 0.900 MHz 0.671 MHz - 0.800 MHz 010 0.901 MHz - 1.100 MHz 0.801 MHz - 1.000 MHz 011 1.101 MHz - 1.300 MHz 1.001 MHz - 1.180 MHz 100 1.301 MHz - 1.480 MHz 1.181 MHz - 1.340 MHz 101 1.481 MHz - 1.600 MHz 1.341 MHz - 1.500 MHz 110 1.601 MHz - 1.700 MHz 1.501 MHz - 1.700 MHz Bass management crossover Table 58. Bit Bass management crossover R/W RST Name 4 R/W 0 XO0 5 R/W 0 XO1 6 R/W 0 XO2 7 R/W 0 XO3 Table 59. Description Selects the bass-management crossover frequency. A 1st-order hign-pass filter (channels 1 and 2) or a 2nd-order low-pass filter (channel 3) at the selected frequency is performed. Bass management crossover frequency XO[3:0] 48/77 Audio preset AM enable 0: switching frequency determined by PWMS setting 1: switching frequency determined by AMAM settings Audio preset AM switching frequency selection AMAM[2:0] 6.8.4 Description Crossover frequency 0000 User-defined 0001 80 Hz 0010 100 Hz 0011 120 Hz 0100 140 Hz 0101 160 Hz 0110 180 Hz 0111 200 Hz 1000 220 Hz 1001 240 Hz Doc ID 15251 Rev 5 STA339BW Register description Table 59. Bass management crossover frequency (continued) XO[3:0] 6.9 6.9.1 Crossover frequency 1010 260 Hz 1011 280 Hz 1100 300 Hz 1101 320 Hz 1110 340 Hz 1111 360 Hz Channel configuration registers (addr 0x0E - 0x10) D7 D6 D5 D4 D3 D2 D1 D0 C1OM1 C1OM0 C1LS1 C1LS0 C1BO C1VPB C1EQBP C1TCB 0 0 0 0 0 0 0 0 D7 D6 D5 D4 D3 D2 D1 D0 C2OM1 C2OM0 C2LS1 C2LS0 C2BO C2VPB C2EQBP C2TCB 0 1 0 0 0 0 0 0 D7 D6 D5 D4 D3 D2 D1 D0 C3OM1 C3OM0 C3LS1 C3LS0 C3BO C3VPB 1 0 0 0 0 0 Reserved 0 0 Tone control bypass Tone control (bass/treble) can be bypassed on a per channel basis for channels 1 and 2. Table 60. Tone control bypass CxTCB 6.9.2 Mode 0 Perform tone control on channel x - normal operation 1 Bypass tone control on channel x EQ bypass EQ control can be bypassed on a per channel basis for channels 1 and 2. If EQ control is bypassed on a given channel the prescale and all filters (high-pass, biquads, de-emphasis, bass, treble in any combination) are bypassed for that channel. Table 61. EQ bypass CxEQBP Mode 0 Perform EQ on channel x - normal operation 1 Bypass EQ on channel x Doc ID 15251 Rev 5 49/77 Register description 6.9.3 STA339BW Volume bypass Each channel contains an individual channel volume bypass. If a particular channel has volume bypassed via the CxVBP = 1 register then only the channel volume setting for that particular channel affects the volume setting, the master volume setting will not affect that channel. 6.9.4 Binary output enable registers Each individual channel output can be set to output a binary PWM stream. In this mode output A of a channel is considered the positive output and output B is negative inverse. Table 62. Binary output enable registers CxBO 6.9.5 Mode 0 FFX 3-state output - normal operation 1 Binary output Limiter select Limiter selection can be made on a per-channel basis according to the channel limiter select bits. . Table 63. Channel limiter mapping as a function of CxLS bits CxLS[1:0] 6.9.6 Channel limiter mapping 00 Channel has limiting disabled 01 Channel is mapped to limiter #1 10 Channel is mapped to limiter #2 Output mapping Output mapping can be performed on a per channel basis according to the CxOM channel output mapping bits. Each input into the output configuration engine can receive data from any of the three processing channel outputs. . Table 64. Channel output mapping as a function of CxOM bits CxOM[1:0] 50/77 Channel x output source from 00 Channel1 01 Channel 2 10 Channel 3 Doc ID 15251 Rev 5 STA339BW 6.10 6.10.1 Register description Tone control register (addr 0x11) D7 D6 D5 D4 D3 D2 D1 D0 TTC3 TTC2 TTC1 TTC0 BTC3 BTC2 BTC1 BTC0 0 1 1 1 0 1 1 1 Tone control Table 65. Tone control boost/cut as a function of BTC and TTC bits BTC[3:0]/TTC[3:0] Boost/Cut 0000 -12 dB 0001 -12 dB ... ... 0111 -4 dB 0110 -2 dB 0111 0 dB 1000 +2 dB 1001 +4 dB ... ... 1101 +12 dB 1110 +12 dB 1111 +12 dB 6.11 Dynamic control registers (addr 0x12 - 0x15) 6.11.1 Limiter 1 attack/release rate 6.11.2 6.11.3 D7 D6 D5 D4 D3 D2 D1 D0 L1A3 L1A2 L1A1 L1A0 L1R3 L1R2 L1R1 L1R0 0 1 1 0 1 0 1 0 Limiter 1 attack/release threshold D7 D6 D5 D4 D3 D2 D1 D0 L1AT3 L1AT2 L1AT1 L1AT0 L1RT3 L1RT2 L1RT1 L1RT0 0 1 1 0 1 0 0 1 Limiter 2 attack/release rate D7 D6 D5 D4 D3 D2 D1 D0 L2A3 L2A2 L2A1 L2A0 L2R3 L2R2 L2R1 L2R0 0 1 1 0 1 0 1 0 Doc ID 15251 Rev 5 51/77 Register description 6.11.4 STA339BW Limiter 2 attack/release threshold D7 D6 D5 D4 D3 D2 D1 D0 L2AT3 L2AT2 L2AT1 L2AT0 L2RT3 L2RT2 L2RT1 L2RT0 0 1 1 0 1 0 0 1 The STA339BW includes two independent limiter blocks. The purpose of the limiters is to automatically reduce the dynamic range of a recording to prevent the outputs from clipping in anti-clipping mode or to actively reduce the dynamic range for a better listening environment such as a night-time listening mode which is often needed for DVDs. The two modes are selected via the DRC bit in Configuration register E (addr 0x04) on page 36. Each channel can be mapped to either limiter or not mapped, meaning that channel will clip when 0 dBfs is exceeded. Each limiter looks at the present value of each channel that is mapped to it, selects the maximum absolute value of all these channels, performs the limiting algorithm on that value, and then if needed adjusts the gain of the mapped channels in unison. The limiter attack thresholds are determined by the LxAT registers if EATHx[7] bits are set to 0 else the thresholds are determined by EATHx[6:0] . It is recommended in anti-clipping mode to set this to 0 dBfs, which corresponds to the maximum unclipped output power of a FFX amplifier. Since gain can be added digitally within the STA339BW it is possible to exceed 0 dBfs or any other LxAT setting, when this occurs, the limiter, when active, automatically starts reducing the gain. The rate at which the gain is reduced when the attack threshold is exceeded is dependent upon the attack rate register setting for that limiter. Gain reduction occurs on a peak-detect algorithm. Setting EATHx[7] bits to 1 selects the anti-clipping mode. The limiter release thresholds are determined by the LxRT registers if ERTHx[7] bits are set to 0 else the thresholds are determined by ERTHx[6:0]. Settings to 1 ERTHx[7] bits the anti-clipping mode is selected automatically. The release of limiter, when the gain is again increased, is dependent on a RMS-detect algorithm. The output of the volume/limiter block is passed through a RMS filter. The output of this filter is compared to the release threshold, determined by the Release Threshold register. When the RMS filter output falls below the release threshold, the gain is again increased at a rate dependent upon the Release Rate register. The gain can never be increased past its set value and, therefore, the release only occurs if the limiter has already reduced the gain. The release threshold value can be used to set what is effectively a minimum dynamic range, this is helpful as over-limiting can reduce the dynamic range to virtually zero and cause program material to sound "lifeless". In AC mode, the attack and release thresholds are set relative to full-scale. In DRC mode, the attack threshold is set relative to the maximum volume setting of the channels mapped to that limiter and the release threshold is set relative to the maximum volume setting plus the attack threshold. 52/77 Doc ID 15251 Rev 5 STA339BW Register description Figure 19. Basic limiter and volume flow diagram Table 66. LxA[3:0] 0000 Limiter attack rate as a function of LxA bits Attack Rate dB/ms Table 67. LxR[3:0] 3.1584 Fast Limiter release rate as a function of LxR bits Release Rate dB/ms 0000 0.5116 0001 0.1370 0001 2.7072 0010 2.2560 0010 0.0744 0011 1.8048 0011 0.0499 0100 1.3536 0100 0.0360 0101 0.9024 0101 0.0299 0110 0.4512 0110 0.0264 0111 0.2256 0111 0.0208 1000 0.1504 1000 0.0198 1001 0.1123 1001 0.0172 1010 0.0902 1010 0.0147 1011 0.0752 1011 0.0137 1100 0.0645 1100 0.0134 1101 0.0564 1101 0.0117 1110 0.0501 1110 0.0110 1111 0.0451 1111 0.0104 Slow Doc ID 15251 Rev 5 Fast Slow 53/77 Register description STA339BW Anti-clipping mode Table 68. Limiter attack threshold as a function of LxAT bits (AC mode) LxAT[3:0] AC (dB relative to fs) Table 69. Limiter release threshold as a function of LxRT bits (AC mode) LxRT[3:0] AC (dB relative to fs) 0000 -12 0000 - 0001 -10 0001 -29 dB 0010 -8 0010 -20 dB 0011 -6 0011 -16 dB 0100 -4 0100 -14 dB 0101 -2 0101 -12 dB 0110 0 0110 -10 dB 0111 +2 0111 -8 dB 1000 +3 1000 -7 dB 1001 +4 1001 -6 dB 1010 +5 1010 -5 dB 1011 +6 1011 -4 dB 1100 +7 1100 -3 dB 1101 +8 1101 -2 dB 1110 +9 1110 -1 dB 1111 +10 1111 -0 dB 54/77 Doc ID 15251 Rev 5 STA339BW Register description Dynamic range compression mode Table 70. Limiter attack threshold as a function of LxAT bits (DRC mode) LxAT[3:0] DRC (dB relative to Volume) Table 71. Limiter release threshold as a as a function of LxRT bits (DRC mode) DRC (db relative to Volume + LxAT) LxRT[3:0] 0000 -31 0000 - 0001 -29 0001 -38 dB 0010 -27 0010 -36 dB 0011 -25 0011 -33 dB 0100 -23 0100 -31 dB 0101 -21 0101 -30 dB 0110 -19 0110 -28 dB 0111 -17 0111 -26 dB 1000 -16 1000 -24 dB 1001 -15 1001 -22 dB 1010 -14 1010 -20 dB 1011 -13 1011 -18 dB 1100 -12 1100 -15 dB 1101 -10 1101 -12 dB 1110 -7 1110 -9 dB 1111 -4 1111 -6 dB 6.11.5 Limiter 1 Extended attack threshold (addr 0x32) D7 D6 D5 D4 D3 D2 D1 D0 EATHEN1 EATH1[6] EATH1[5] EATH1[4] EATH1[3] EATH1[2] EATH1[1] EATH1[0] TBD TBD TBD TBD TBD TBD TBD TBD The extended attack threshold value is determined as follows: attack threshold = -12 + EATH1 / 4 6.11.6 Limiter 1 Extended release threshold (addr 0x33) D7 D6 D5 D4 D3 D2 D1 D0 ERTHEN1 ERTH1[6] ERTH1[5] ERTH1[4] ERTH1[3] ERTH1[2] ERTH1[1] ERTH1[0] TBD TBD TBD TBD TBD TBD TBD TBD The extended release threshold value is determined as follows: release threshold = -12 + ERTH1 / 4 Doc ID 15251 Rev 5 55/77 Register description 6.11.7 STA339BW Limiter 2 Extended attack threshold (addr 0x34) D7 D6 D5 D4 D3 D2 D1 D0 EATHEN2 EATH2[6] EATH2[5] EATH2[4] EATH2[3] EATH2[2] EATH2[1] EATH2[0] TBD TBD TBD TBD TBD TBD TBD TBD The extended attack threshold value is determined as follows: attack threshold = -12 + EATH2 / 4 6.11.8 Limiter 2 Extended release threshold (addr 0x35) D7 D6 D5 D4 D3 D2 D1 D0 ERTHEN2 ERTH2[6] ERTH2[5] ERTH2[4] ERTH2[3] ERTH2[2] ERTH2[1] ERTH2[0] TBD TBD TBD TBD TBD TBD TBD TBD The extended release threshold value is determined as follows: release threshold = -12 + ERTH2 / 4 Note: Attack/release threshold step is 0.125 dB in the range -12 dB and 0 dB. 6.12 User-defined coefficient control registers (addr 0x16 - 0x26) 6.12.1 Coefficient address register D7 6.12.2 6.12.3 6.12.4 56/77 D5 D4 D3 D2 D1 D0 Reserved D6 CFA5 CFA4 CFA3 CFA2 CFA1 CFA0 0 0 0 0 0 0 0 Coefficient b1 data register bits 23:16 D7 D6 D5 D4 D3 D2 D1 D0 C1B23 C1B22 C1B21 C1B20 C1B19 C1B18 C1B17 C1B16 0 0 0 0 0 0 0 0 Coefficient b1 data register bits 15:8 D7 D6 D5 D4 D3 D2 D1 D0 C1B15 C1B14 C1B13 C1B12 C1B11 C1B10 C1B9 C1B8 0 0 0 0 0 0 0 0 Coefficient b1 data register bits 7:0 D7 D6 D5 D4 D3 D2 D1 D0 C1B7 C1B6 C1B5 C1B4 C1B3 C1B2 C1B1 C1B0 0 0 0 0 0 0 0 0 Doc ID 15251 Rev 5 STA339BW 6.12.5 6.12.6 6.12.7 6.12.8 6.12.9 6.12.10 6.12.11 Register description Coefficient b2 data register bits 23:16 D7 D6 D5 D4 D3 D2 D1 D0 C2B23 C2B22 C2B21 C2B20 C2B19 C2B18 C2B17 C2B16 0 0 0 0 0 0 0 0 Coefficient b2 data register bits 15:8 D7 D6 D5 D4 D3 D2 D1 D0 C2B15 C2B14 C2B13 C2B12 C2B11 C2B10 C2B9 C2B8 0 0 0 0 0 0 0 0 Coefficient b2 data register bits 7:0 D7 D6 D5 D4 D3 D2 D1 D0 C2B7 C2B6 C2B5 C2B4 C2B3 C2B2 C2B1 C2B0 0 0 0 0 0 0 0 0 Coefficient a1 data register bits 23:16 D7 D6 D5 D4 D3 D2 D1 D0 C1B23 C1B22 C1B21 C1B20 C1B19 C1B18 C1B17 C1B16 0 0 0 0 0 0 0 0 Coefficient a1 data register bits 15:8 D7 D6 D5 D4 D3 D2 D1 D0 C3B15 C3B14 C3B13 C3B12 C3B11 C3B10 C3B9 C3B8 0 0 0 0 0 0 0 0 Coefficient a1 data register bits 7:0 D7 D6 D5 D4 D3 D2 D1 D0 C3B7 C3B6 C3B5 C3B4 C3B3 C3B2 C3B1 C3B0 0 0 0 0 0 0 0 0 Coefficient a2 data register bits 23:16 D7 D6 D5 D4 D3 D2 D1 D0 C4B23 C4B22 C4B21 C4B20 C4B19 C4B18 C4B17 C4B16 0 0 0 0 0 0 0 0 Doc ID 15251 Rev 5 57/77 Register description 6.12.12 6.12.13 6.12.14 6.12.15 6.12.16 6.12.17 STA339BW Coefficient a2 data register bits 15:8 D7 D6 D5 D4 D3 D2 D1 D0 C4B15 C4B14 C4B13 C4B12 C4B11 C4B10 C4B9 C4B8 0 0 0 0 0 0 0 0 Coefficient a2 data register bits 7:0 D7 D6 D5 D4 D3 D2 D1 D0 C4B7 C4B6 C4B5 C4B4 C4B3 C4B2 C4B1 C4B0 0 0 0 0 0 0 0 0 Coefficient b0 data register bits 23:16 D7 D6 D5 D4 D3 D2 D1 D0 C5B23 C5B22 C5B21 C5B20 C5B19 C5B18 C5B17 C5B16 0 0 0 0 0 0 0 0 Coefficient b0 data register bits 15:8 D7 D6 D5 D4 D3 D2 D1 D0 C5B15 C5B14 C5B13 C5B12 C5B11 C5B10 C5B9 C5B8 0 0 0 0 0 0 0 0 Coefficient b0 data register bits 7:0 D7 D6 D5 D4 D3 D2 D1 D0 C5B7 C5B6 C5B5 C5B4 C5B3 C5B2 C5B1 C5B0 0 0 0 0 0 0 0 0 Coefficient write/read control register D7 D6 D3 D2 D1 D0 Reserved D5 D4 RA R1 WA W1 0 0 0 0 0 Coefficients for user-defined EQ, mixing, scaling, and bass management are handled internally in the STA339BW via RAM. Access to this RAM is available to the user via an I2C register interface. A collection of I2C registers are dedicated to this function. One contains a coefficient base address, five sets of three store the values of the 24-bit coefficients to be written or that were read, and one contains bits used to control the write/read of the coefficient(s) to/from RAM. Three different RAM banks are embedded in STA339BW. The three banks are managed in paging mode using EQCFG register bits. They can be used to store different EQ settings. For speaker frequency compensation, a sampling frequency independent EQ must be implemented. Computing three different coefficients set for 32 kHz, 44.1kHz, 48 kHz and downloading them into the three RAM banks, it is possible to select the suitable RAM block depending from the incoming frequency with a simple I2C write operation on register 0x31. 58/77 Doc ID 15251 Rev 5 STA339BW Register description For example, in case of different input sources (different sampling rates), the three different sets of coefficients can be downloaded once at the start up, and during the normal play it is possible to switch among the three RAM blocks allowing a faster operation, without any additional download from the microcontroller. To write the coefficients in a particular RAM bank, this bank must be selected first writing bit 0 and bit 1 in register 0x31. Then the write procedure below can be used. Note that as soon as a RAM bank is selected, the EQ settings are automatically switched to the coefficients stored in the active RAM block. Note: The read and write operation on RAM coefficients works only if LRCKI (pin 29) is switching. Reading a coefficient from RAM 1. Select the RAM block with register 0x31 bit1, bit0. 2. Write 6 bits of address to I2C register 0x16. 3. Write 1 to R1 bit in I2C address 0x26. 4. Read top 8 bits of coefficient in I2C address 0x17. 5. Read middle 8 bits of coefficient in I2C address 0x18. 6. Read bottom 8 bits of coefficient in I2C address 0x19. Reading a set of coefficients from RAM 1. Select the RAM block with register 0x31 bit1, bit0. 2. Write 6 bits of address to I2C register 0x16. 3. Write 1 to RA bit in I2C address 0x26. 4. Read top 8 bits of coefficient in I2C address 0x17. 5. Read middle 8 bits of coefficient in I2C address 0x18. 6. Read bottom 8 bits of coefficient in I2C address 0x19. 7. Read top 8 bits of coefficient b2 in I2C address 0x1A. 8. Read middle 8 bits of coefficient b2 in I2C address 0x1B. 9. Read bottom 8 bits of coefficient b2 in I2C address 0x1C. 10. Read top 8 bits of coefficient a1 in I2C address 0x1D. 11. Read middle 8 bits of coefficient a1 in I2C address 0x1E. 12. Read bottom 8 bits of coefficient a1 in I2C address 0x1F. 13. Read top 8 bits of coefficient a2 in I2C address 0x20. 14. Read middle 8 bits of coefficient a2 in I2C address 0x21. 15. Read bottom 8 bits of coefficient a2 in I2C address 0x22. 16. Read top 8 bits of coefficient b0 in I2C address 0x23. 17. Read middle 8 bits of coefficient b0 in I2C address 0x24. 18. Read bottom 8 bits of coefficient b0 in I2C address 0x25. Doc ID 15251 Rev 5 59/77 Register description STA339BW Writing a single coefficient to RAM 1. Select the RAM block with register 0x31 bit1, bit0. 2. Write 6 bits of address to I2C register 0x16. 3. Write top 8 bits of coefficient in I2C address 0x17. 4. Write middle 8 bits of coefficient in I2C address 0x18. 5. Write bottom 8 bits of coefficient in I2C address 0x19. 6. Write 1 to W1 bit in I2C address 0x26. Writing a set of coefficients to RAM 1. Select the RAM block with register 0x31 bit1, bit0. 2. Write 6 bits of starting address to I2C register 0x16. 3. Write top 8 bits of coefficient b1 in I2C address 0x17. 4. Write middle 8 bits of coefficient b1 in I2C address 0x18. 5. Write bottom 8 bits of coefficient b1 in I2C address 0x19. 6. Write top 8 bits of coefficient b2 in I2C address 0x1A. 7. Write middle 8 bits of coefficient b2 in I2C address 0x1B. 8. Write bottom 8 bits of coefficient b2 in I2C address 0x1C. 9. Write top 8 bits of coefficient a1 in I2C address 0x1D. 10. Write middle 8 bits of coefficient a1 in I2C address 0x1E. 11. Write bottom 8 bits of coefficient a1 in I2C address 0x1F. 12. Write top 8 bits of coefficient a2 in I2C address 0x20. 13. Write middle 8 bits of coefficient a2 in I2C address 0x21. 14. Write bottom 8 bits of coefficient a2 in I2C address 0x22. 15. Write top 8 bits of coefficient b0 in I2C address 0x23. 16. Write middle 8 bits of coefficient b0 in I2C address 0x24. 17. Write bottom 8 bits of coefficient b0 in I2C address 0x25. 18. Write 1 to WA bit in I2C address 0x26. The mechanism for writing a set of coefficients to RAM provides a method of updating the five coefficients corresponding to a given biquad (filter) simultaneously to avoid possible unpleasant acoustic side-effects. When using this technique, the 6-bit address specifies the address of the biquad b1 coefficient (for example, 0, 5, 10, 20, 35 decimal), and the STA339BW generates the RAM addresses as offsets from this base value to write the complete set of coefficient data. 60/77 Doc ID 15251 Rev 5 STA339BW 6.12.18 Register description User-defined EQ The STA339BW can be programmed for four EQ filters (biquads) per each of the two input channels. The biquads use the following equation: Y[n] = 2 * (b0 / 2) * X[n] + 2 * (b1 / 2) * X[n-1] + b2 * X[n-2] - 2 * (a1 / 2) * Y[n-1] - a2 * Y[n-2] = b0 * X[n] + b1 * X[n-1] + b2 * X[n-2] - a1 * Y[n-1] - a2 * Y[n-2] where Y[n] represents the output and X[n] represents the input. Multipliers are 24-bit signed fractional multipliers, with coefficient values in the range of 0x800000 (-1) to 0x7FFFFF (0.9999998808). Coefficients stored in the user defined coefficient RAM are referenced in the following manner: CxHy0 = b1 / 2 CxHy1 = b2 CxHy2 = -a1 / 2 CxHy3 = -a2 CxHy4 = b0 / 2 where x represents the channel and the y the biquad number. For example, C2H41 is the b2 coefficient in the fourth biquad for channel 2. Additionally, the STA339BW can be programmed for a high-pass filter (processing channels 1 and 2) and a low-pass filter (processing channel 3) to be used for bass-management crossover when the XO setting is 000 (user-defined). Both of these filters when defined by the user (rather than using the preset crossover filters) are second order filters that use the biquad equation given above. They are loaded into the C12H0-4 and C3Hy0-4 areas of RAM noted in Table 72. By default, all user-defined filters are pass-through where all coefficients are set to 0, except the b0/2 coefficient which is set to 0x400000 (representing 0.5) 6.12.19 Prescale The STA339BW provides a multiplication for each input channel for the purpose of scaling the input prior to EQ. This pre-EQ scaling is accomplished by using a 24-bit signed fractional multiplier, with 0x800000 = -1 and 0x7FFFFF = 0.9999998808. The scale factor for this multiplication is loaded into RAM using the same I2C registers as the biquad coefficients and the bass management. All channels can use the channel-1 prescale factor by setting the Biquad link bit. By default, all prescale factors are set to 0x7FFFFF. 6.12.20 Postscale The STA339BW provides one additional multiplication after the last interpolation stage and the distortion compensation on each channel. This postscaling is accomplished by using a 24-bit signed fractional multiplier, with 0x800000 = -1 and 0x7FFFFF = 0.9999998808. The scale factor for this multiply is loaded into RAM using the same I2C registers as the biquad coefficients and the bass management. This postscale factor can be used in conjunction with an ADC equipped microcontroller to perform power-supply error correction. All channels can use the channel-1 postscale factor by setting the postscale link bit. By default, all postscale factors are set to 0x7FFFFF. When line output is being used, channel-3 postscale will affect both channels 3 and 4. Doc ID 15251 Rev 5 61/77 Register description 6.12.21 STA339BW Overcurrent postscale The STA339BW provides a simple mechanism for reacting to overcurrent detection in the power block. When the ocwarn input is asserted, the overcurrent postscale value is used in place of the normal postscale value to provide output attenuation on all channels. The default setting provides 3 dB of output attenuation when ocwarn is asserted. The amount of attenuation to be applied in this situation can be adjusted by modifying the Overcurrent postscale value. As with the normal postscale, this scaling value is a 24-bit signed fractional multiplier, with 0x800000 = -1 and 0x7FFFFF = 0.9999998808. By default, the overcurrent postscale factor is set to 0x5A9DF7. Once the overcurrent attenuation is applied, it remains until the device is reset. Table 72. RAM block for biquads, mixing, scaling and bass management Index (decimal) Index (hex) RAM block setting Coefficient Default 0 0x00 C1H10(b1/2) 0x000000 1 0x01 C1H11(b2) 0x000000 2 0x02 C1H12(a1/2) 0x000000 3 0x03 C1H13(a2) 0x000000 4 0x04 C1H14(b0/2) 0x400000 5 0x05 Channel 1 - Biquad 2 C1H20 0x000000 ... ... ... ... ... 19 0x13 Channel 1 - Biquad 4 C1H44 0x400000 20 0x14 C2H10 0x000000 C2H11 0x000000 Channel 1 - Biquad 1 Channel 2 - Biquad 1 21 0x15 ... ... ... ... ... 39 0x27 Channel 2 - Biquad 4 C2H44 0x400000 40 0x28 C12H0(b1/2) 0x000000 41 0x29 C12H1(b2) 0x000000 42 0x2A C12H2(a1/2) 0x000000 43 0x2B C12H3(a2) 0x000000 44 0x2C C12H4(b0/2) 0x400000 45 0x2D C3H0(b1/2) 0x000000 46 0x2E C3H1(b2) 0x000000 47 0x2F C3H2(a1/2) 0x000000 48 0x30 C3H3(a2) 0x000000 49 0x31 C3H4(b0/2) 0x400000 50 0x32 Channel 1 - Prescale C1PreS 0x7FFFFF 51 0x33 Channel 2 - Prescale C2PreS 0x7FFFFF 52 0x34 Channel 1 - Postscale C1PstS 0x7FFFFF 53 0x35 Channel 2 - Postscale C2PstS 0x7FFFFF 62/77 Channel 1/2 - Biquad 5 for XO = 000 High-pass 2nd order filter for XO000 Channel 3 - Biquad for XO = 000 Low-pass 2nd order filter for XO000 Doc ID 15251 Rev 5 STA339BW Table 72. Register description RAM block for biquads, mixing, scaling and bass management (continued) Index (decimal) Index (hex) RAM block setting Coefficient Default 54 0x36 Channel 3 - Postscale C3PstS 0x7FFFFF 55 0x37 TWARN/OC - Limit TWOCL 0x5A9DF7 56 0x38 Channel 1 - Mix 1 C1MX1 0x7FFFFF 57 0x39 Channel 1 - Mix 2 C1MX2 0x000000 58 0x3A Channel 2 - Mix 1 C2MX1 0x000000 59 0x3B Channel 2 - Mix 2 C2MX2 0x7FFFFF 60 0x3C Channel 3 - Mix 1 C3MX1 0x400000 61 0x3D Channel 3 - Mix 2 C3MX2 0x400000 62 0x3E Unused - - 63 0x3F Unused - - 6.13 Variable max power correction registers (addr 0x27 - 0x28) D7 D6 D5 D4 D3 D2 D1 D0 MPCC15 MPCC14 MPCC13 MPCC12 MPCC11 MPCC10 MPCC9 MPCC8 0 0 0 1 1 0 1 0 D7 D6 D5 D4 D3 D2 D1 D0 MPCC7 MPCC6 MPCC5 MPCC4 MPCC3 MPCC2 MPCC1 MPCC0 1 1 0 0 0 0 0 0 MPCC bits determine the 16 MSBs of the MPC compensation coefficient. This coefficient is used in place of the default coefficient when MPCV = 1. 6.14 Variable distortion compensation registers (addr 0x29 0x2A) D7 D6 D5 D4 D3 D2 D1 D0 DCC15 DCC14 DCC13 DCC12 DCC11 DCC10 DCC9 DCC8 1 1 1 1 0 0 1 1 D7 D6 D5 D4 D3 D2 D1 D0 DCC7 DCC6 DCC5 DCC4 DCC3 DCC2 DCC1 DCC0 0 0 1 1 0 0 1 1 DCC bits determine the 16 MSBs of the Distortion compensation coefficient. This coefficient is used in place of the default coefficient when DCCV = 1. Doc ID 15251 Rev 5 63/77 Register description 6.15 STA339BW Fault detect recovery constant registers (addr 0x2B - 0x2C) D7 D6 D5 D4 D3 D2 D1 D0 FDRC15 FDRC14 FDRC13 FDRC12 FDRC11 FDRC10 FDRC9 FDRC8 0 0 0 0 0 0 0 0 D7 D6 D5 D4 D3 D2 D1 D0 FDRC7 FDRC6 FDRC5 FDRC4 FDRC3 FDRC2 FDRC1 FDRC0 0 0 0 0 1 1 0 0 FDRC bits specify the 16-bit fault detect recovery time delay. When FAULT is asserted, the TRISTATE output is immediately asserted low and held low for the time period specified by this constant. A constant value of 0x0001 in this register is approximately 0.083 ms. The default value of 0x000C gives approximately 0.1 ms. 6.16 Device status register (addr 0x2D) D7 D6 D5 D4 D3 D2 D1 D0 PLLUL FAULT UVFAULT OVFAULT OCFAULT OCWARN TFAULT TWARN This read-only register provides fault- and thermal-warning status information from the power control block. Logic value 1 for faults or warning means normal state. Logic 0 means a fault or warning has been detected on the power bridge. The PLLUL = 1 means that the PLL is not locked. Table 73. Bit 64/77 Status register bits R/W RST Name Description 7 R - PLLUL 0: PLL locked 1: PLL not locked 6 R - FAULT 0: fault detected on power bridge 1: normal operation 5 R - UVFAULT 0: VCCxX internally detected 1: undervoltage threshold 4 R - OVFAULT 0: VCCxX internally detected 1: overvoltage threshold 3 R - OCFAULT 0: overcurrent fault detected 2 R - OCWARN 0: overcurrent warning 1 R - TFAULT 0: thermal fault, junction temperature over limit 0 R - TWARN 0: thermal warning, junction temperature is close to fault condition Doc ID 15251 Rev 5 STA339BW 6.17 Register description EQ coefficients and DRC configuration register (addr 0x31) D7 D6 XOB D5 Reserved 0 0 Table 74. 0 D4 D3 D2 D1 D0 AMGC[3] AMGC[2] Reserved SEL[1] SEL[0] 0 0 0 0 0 EQ RAM select SEL[1:0] EQ RAM bank selected 00/11 Bank 0 activated 01 Bank 1 activated 10 Bank 2 activated Bits AMGC[3:2] change the behavior of the bits AMGC[1:0] as given in Table 75 below. Table 75. Anti-clipping and DRC preset AMGC[3:2] Anti-clipping and DRC preset selected 00 DRC/Anti-clipping behavior described in Table 55 on page 47 (default). 01 DRC/Anti-clipping behavior is described in Table 76 below 10/11 Reserved, do not use When AMGC[3:2] = 01 then the bits 1:0 are defined as given here in Table 76. Table 76. Anti-clipping selection for AMGC[3:2] = 01 AMGC[1:0] Mode 00 AC0, stereo anticlipping 0 dB limiter 01 AC1, stereo anticlipping +1.25 dB limiter 10 AC2, stereo anticlipping +2 dB limiter 11 Reserved do not use AC0, AC1, AC2 settings are designed for the loudspeaker protection function, limiting at the minimum any audio artefacts introduced by typical anti-clipping/DRC algorithms. More detailed information is available in the applications notes "Configurable output power rate using STA335BW" and "STA335BWS vs STA335BW". Bit XOB can be used to bypass the crossover filters. Logic 1 means that the function is not active. In this case, high pass crossover filter works as a passtrough on the data path (b0 = 1, all the other coefficients at logic 0) while the low pass filter is configured to have zero signal on channel-3 data processing (all the coefficients are at logic 0). 6.18 Extended configuration register (addr 0x36) D7 D6 D5 D4 D3 D2 D1 D0 Mdrc[1] Mdrc[0] PS48DB XAR1 XAR2 BQ5 BQ6 BQ7 0 0 0 0 0 0 0 0 2 Extended configuration register provides access to B DRC and biquads 5, 6 and 7. Doc ID 15251 Rev 5 65/77 Register description 6.18.1 STA339BW Dual-band DRC The STA339BW provides a dual-band DRC (B2DRC) on the left- and right-channel data path, as depicted in Figure 20. Dual-band DRC is activated by setting MDRC[1:0] = 1x. Figure 20. B2DRC scheme Ch1 Volume L + Pass B2DRC XO Filter Hi-pass filter Limiter And Vol DRC1 - Ch3 Volume Ch2 Volume Limiter And Vol DRC2 DRC1 + R Pass XO 2DRC BFilter Hi-pass filter Ch3 - Volume Limiter And Vol DRC2 The low-frequency information (LFE) is extracted from the left and right channels by removing the high frequencies with a programmable Biquad filter, so that, using the original signal, the difference signal can be computed. Limiter 1 (DRC1) is then used to control the left and right high-frequency component amplitudes while limiter 2 (DRC2) is used to control the low-frequency components (see Chapter 6.11). The cutoff frequency of the high-pass filters can be user defined, XO[3:0] = 0, or selected from the pre-defined values. DRC1 and DRC2 are then used to independently limit the left- and right-channel high frequencies and the LFE-channel amplitude (see Chapter 6.11) as well as their volume control. Note that, in this configuration, the dedicated channel-3 volume control can actually be used as a bass boost enhancer as well (0.5 dB/step resolution). The processed LFE channel is then recombined with the L and R channels in order to reconstruct the 2.0 output signal. Sub band decomposition The sub band decomposition for B2DRC can be configured specifying the cutoff frequency. The cut off frequency can be programmed in two ways, using XO bits in register 0x0C, or using "user programmable" mode (coefficients stored in RAM adresses 0x28 to 0x31). For the user programmable mode, use the formulae below to compute the high pass filters: b0 = (1 + alpha) / 2 a0 = 1 b1 = -(1 + alpha) / 2 a1 = -alpha b2 = 0 a2 = 0 where alpha = (1-sin(0))/cos(0), and 0 is the cutoff frequency. 66/77 Doc ID 15251 Rev 5 STA339BW Register description A first-order filter is suggested to guarantee that for every 0 the corresponding low-pass filter obtained as difference (as shown in Figure 20) will have a symmetric (relative to HP filter) frequency response, and the corresponding recombination after the DRC has low ripple. Second-order filters can be used as well, but in this case the filter shape must be carefully choosen to provide good low pass response and minimum ripple recombination. For second-order is not possible to give a closed formula to get the best coefficients, but empirical adjustment should be done. DRC settings The DRC blocks used by B2DRC are the same as those described in Chapter 6.11. B2DRC configure automatically the DRC blocks in anticlipping mode. Attack and release thresholds can be selected using registers 0x32, 0x33, 0x34, 0x35, while attack and release rates are configured by registers 0x12 and 0x14. Band downmixing The low-frequency band is down-mixed to the left and right channels at the B2DRC output. Channel volume can be used to weight the bands recombination to fine tune the overall frequency response. 6.18.2 EQ DRC mode Setting MDRC = 01, it is possible to add a programmable biquad (the XO biquad at RAM addresses 0x28 to 0x2C is used for this purpose) to the Limiter/compressor measure path (side chain). Using EQDRC the peak detector input can be shaped in frequency using the programmable biquad. For example if a +2 dB bass boost is applied (using a low shelf filter for example), the effect is that the EQDRC out will limit bass frequencies to -2 dB below the selected attack treshold. Generally speaking, if the biquad boosts frequency f with an amount of X dB, the level of a compressed sinusoid at the output will be TH - X, where TH is the selected attack threshold. Note: EQDRC works only if the biquad frequency response magnitude is >= 0 dB for every frequency. Figure 21. EQDRC scheme EQDRC Atten Channel in BIQUAD Peak detector Attenuation calculator Standard DRC Atten Channel in Peak detector Doc ID 15251 Rev 5 Attenuation calculator 67/77 Register description 6.18.3 STA339BW Extended post scale range Table 77. Post scale setup PS48DB Mode 0 Postscale value is applied as defined in coefficient RAM 1 Postscale value is applied with +48-dB offset with respect to the coefficient RAM value Post scale is an attenuation by default. When PS48DB is set to 1, a 48-dB offset is applied to the configured word, so postscale can act as a gain too. 6.18.4 Extended attack rate The attack rate shown in Table 66 can be extended to provide up to 8 dB/ms attack rate on both limiters. Table 78. Extended attack rate setup for limiter 1 XAR1 Mode 0 Limiter1 attack rate is configured using Table 66 1 Limiter1 attack rate is 8 dB/ms Table 79. Extended attack rate setup for limiter 2 XAR2 68/77 Mode 0 Limiter2 attack rate is configured using Table 66 1 Limiter2 attack rate is 8 dB/ms Doc ID 15251 Rev 5 STA339BW 6.18.5 Register description Extended BIQUAD selector De-ephasis filter as well as bass and treble controls can be configured as user defined filters when equalization coefficients link is activated (BQL = 1) and the corresponding BQx bit is set to 1. Table 80. De-emphasis filter setup BQ5 Mode 0 Preset de-emphasis filter selected 1 User defined biquad 5 coefficients are selected Table 81. Bass filter setup BQ6 Mode 0 Preset bass filter selected as per Table 65 1 User defined biquad 6 coefficients are selected Table 82. Treble filter setup BQ7 Mode 0 Preset treble filter selected as per Table 65 1 User defined biquad 7 coefficients are selected When filters from 5th to 7th are configured as user-programmable, the corresponding coefficients are stored respectively in addresses 0x20-0x24 (BQ5), 0x25-0x29 (BQ6), 0x2A0x2E (BQ7) as in Table 72. Note: BQx bits are ignored if BQL = 0 or if DEMP = 1 (relevant for BQ5) or CxTCB = 1 (relevant for BQ6 and BQ7). 6.19 EQ soft volume configuration registers (addr 0x37 - 0x38) D7 D6 Reserved D5 D4 D3 D2 D1 D0 SVUPE SVUP[4] SVUP[3] SVUP[2] SVUP[1] SVUP[0] 0 0 0 0 0 0 0 0 D7 D6 D5 D4 D3 D2 D1 D0 SVDWE SVDW4] SVDW[3] SVDW[2] SVDW[1] SVDW[0] 0 0 0 0 0 0 Reserved 0 0 Soft volume update has a fixed rate by default. Using register 0x37 and 0x38 it is possible to override the default behavior allowing different volume change rates. It is also possible to independently define the fade-in (volume is increased) and fade-out (volume is decreased) rates according to the desired behavior. Doc ID 15251 Rev 5 69/77 Register description STA339BW Table 83. Soft volume (increasing) setup SVUPE Mode 0 When volume is increased, use the default rate 1 When volume is increased, use the rates defined by SVUP[4:0] . When SVUPE = 1 the fade-in rate is defined by the SVUP[4:0] bits according to the formula: Fade-in rate = 48 / (SVUP[4:0] + 1) dB/ms. Table 84. Soft volume (decreasing) setup SVDWE Mode 0 When volume is decreased, use the default rate 1 When volume is decreased, use the rates defined by SVDW[4:0] . When SVDWE = 1 the fade-out rate is defined by the SVDW[4:0] bits according to the formula: Fade-in rate = 48 / (SVDW[4:0] + 1) dB/ms. 6.20 DRC RMS filter coefficients (addr 0x39 - 0x3E) D7 D6 D5 D4 D3 D2 D1 D0 R_C0[23] R_C0[22] R_C0[21] R_C0[20] R_C0[19] R_C0[18] R_C0[17] R_C0[16] 0 0 0 0 0 0 0 1 D7 D6 D5 D4 D3 D2 D1 D0 R_C0[15] R_C0[14] R_C0[13] R_C0[12] R_C0[11] R_C0[10] R_C0[9] R_C0[8] 1 1 1 0 1 1 1 0 D7 D6 D5 D4 D3 D2 D1 D0 R_C0[7] R_C0[6] R_C0[5] R_C0[4] R_C0[3] R_C0[2] R_C0[1] R_C0[0] 1 1 1 1 1 1 1 1 D7 D6 D5 D4 D3 D2 D1 D0 R_C1[23] R_C1[22] R_C1[21] R_C1[20] R_C1[19] R_C1[18] R_C1[17] R_C1[16] 0 1 1 1 1 1 1 0 D7 D6 D5 D4 D3 D2 D1 D0 R_C1[15] R_C1[14] R_C1[13] R_C1[12] R_C1[11] R_C1[10] R_C1[9] R_C1[8] 1 1 0 0 0 0 0 0 D7 D6 D5 D4 D3 D2 D1 D0 R_C1[7] R_C1[6] R_C1[5] R_C1[4] R_C1[3] R_C1[2] R_C1[1] R_C1[0] 0 0 1 0 0 1 1 0 Signal level detection in DRC algorithm is computed usign the following formula: y(t) = c0 * abs(x(t)) + c1 * y(t-1) where x(t) represents the audio signal applied to the limiter, and y(t) the measured level. 70/77 Doc ID 15251 Rev 5 STA339BW Application 7 Application 7.1 Application scheme for power supplies Here in Figure 22 below is the typical application diagram for STA339BW showing the power supply decoupling. Particular care has to be taken with the layout of the PCB. In particular the 3.3 resistors on the digital supplies (VDD_DIG) have to be placed as close as possible to the device. This helps to prevent unwanted oscillation in the digital part of the device due to the inductive tracks of the PCB. The same rule also applies to all the decoulpling capacitors in order to limit spikes on all the supplies. Figure 22. Application diagram 7.2 PLL filter It is recommended to use the above scheme and values for the PLL filter to achieve the best performance from the device in general applications. Note that the ground of this filter circuit has to be connected to the ground of the PLL without any resistive path. Concerning the component values, remember that the greater is the filter bandwidth, the less is the lock time but the higher is the PLL output jitter. Doc ID 15251 Rev 5 71/77 Application 7.3 STA339BW Typical output configuration Here after the typical output configuration used for BTL stereo mode. Please refer to the application note for all the other possible output configuration recommended schematics. Figure 23. Output configuration for stereo BTL mode 22uH OUT1A 100nF 6.2 22 6.2 330pF 100nF 470nF LEFT 470nF RIGHT 100nF 100nF OUT1B 22uH 22uH OUT2A 100nF 6.2 22 6.2 330pF 100nF OUT2B 22uH 72/77 Doc ID 15251 Rev 5 100nF 100nF STA339BW 8 Package thermal characteristics Package thermal characteristics Using a double-layer PCB the thermal resistance junction to ambient with 2 copper ground areas of 3 x 3 cm2 and with 16 via holes (see Figure 24) is 24 C/W in natural air convection. The dissipated power within the device depends primarily on the supply voltage, load impedance and output modulation level. Thus, the maximum estimated dissipated power for the STA339BW is: 2 x 20 W @ 8 , 18 V Pd max ~ 4 W 2 x 10 W + 1 x 20 W @ 4 , 8 , 18 V Pd max < 5 W Figure 24. Double-layer PCB with 2 copper ground areas and 16 via holes Figure 25 shows the power derating curve for the PowerSSO-36 slug-down package on PCBs with copper areas of 2 x 2 cm2 and 3 x 3 cm2. Figure 25. PowerSSO-36 power derating curve Pd (W) 8 7 Copper Area 3x3 cm and via holes 6 5 STA339BW STA339BW PSSO36 PowerSSO-36 4 3 Copper Area 2x2 cm and via holes 2 1 0 0 20 40 60 80 100 120 140 160 Tamb ( C) Doc ID 15251 Rev 5 73/77 Package mechanical data 9 STA339BW Package mechanical data Figure 26 shows the package outline and Table 85 gives the dimensions of the PowerSSO-36 package with exposed pad (slug) down (EPD). Table 85. PowerSSO-36 EPD dimensions Dimensions in mm Dimensions in inches Symbol Min Typ Max Min Typ Max A 2.15 - 2.47 0.085 - 0.097 A2 2.15 - 2.40 0.085 - 0.094 a1 0 - 0.10 0 - 0.004 b 0.18 - 0.36 0.007 - 0.014 c 0.23 - 0.32 0.009 - 0.013 D 10.10 - 10.50 0.398 - 0.413 E 7.40 - 7.60 0.291 - 0.299 e - 0.5 - - 0.020 - e3 - 8.5 - - 0.335 - F - 2.3 - - 0.091 - G - - 0.10 - - 0.004 H 10.10 - 10.50 0.398 - 0.413 h - - 0.40 - - 0.016 k 0 - 8 degrees - - 8 degrees L 0.60 - 1.00 0.024 - 0.039 M - 4.30 - - 0.169 - N - - 10 degrees - O - 1.20 - - 0.047 - Q - 0.80 - - 0.031 - S - 2.90 - - 0.114 - T - 3.65 - - 0.144 - U - 1.00 - - 0.039 - X 4.10 - 4.70 0.161 - 0.185 Y 4.90 - 7.10 0.193 - 0.280 10 degrees In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK(R) packages, depending on their level of environmental compliance. ECOPACK(R) specifications, grade definitions and product status are available at: www.st.com. ECOPACK(R) is an ST trademark. 74/77 Doc ID 15251 Rev 5 h x 45 STA339BW Figure 26. PowerSSO-36 EPD outline drawing Doc ID 15251 Rev 5 Package mechanical data 75/77 Revision history 10 STA339BW Revision history Table 86. 76/77 Document revision history Date Revision Changes 09-Dec-2008 1 Initial release 16-Feb-2009 2 Updated names/descriptions for pins 17-20 in Chapter 2 on page 12 Added cross reference to I2S interface setup in Section 3.6: Power on/off sequence on page 18 Updated text and Figure 22: Application diagram on page 71 Updated Section 7.2: PLL filter on page 71 01-Apr-2009 3 Updated Y dimension in Table 85: PowerSSO-36 EPD dimensions on page 74 15-May-2009 4 Updated Chapter 1 on page 10 to "8 programmable 28-bit biquads" Updated Iil and Iih in Table 6: Electrical specifications - digital section on page 15 Updated Ilim and Isc in Table 7: Electrical specifications - power section on page 16 Updated register FDRC addresses in Section 6.1.5: Fault detect recovery bypass on page 29 Updated bits 4 and 5 in Table 73: Status register bits on page 64. 04-Aug-2010 5 Updated order code in Table 1: Device summary on page 1 Updated name of Chapter 9 on page 74 to Package mechanical data Doc ID 15251 Rev 5 STA339BW Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries ("ST") reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST's terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST'S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER'S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. (c) 2010 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com Doc ID 15251 Rev 5 77/77