PART NUMBERS
199AX, 199X, 199AMX¹,
199MX¹, 199ABX²,
199BX²
199ADX, 199DX,
199ADYX, 199DYX,
199ADBX², 199DBX²
199P³,4, 199AP³,4 199ADE, 199DE,
199ADBE², 199DBE²
CONTACT CHARACTERISTICS
Number and type of contacts SPST, SPDT, DPST, DPDT SPST-DM, SPST-DB DPDT, SPDT SPST-DM
Contact material AgSnO
Thermal (carrying) current rating 40 A 50 A
Maximum switching voltage 600 V(rms)
Rated Switching current at
voltage
Resistive 40 A at 300 VAC;
5 A at 480 VAC;
5 A at 600 VAC;
40 A at 28 VDC
40 A at 300 VAC;
12 A at 480 VAC;
10 A at 600 VAC;
40 A at 28 VDC
50 A at 300 VAC;
5 A at 480 VAC;
5 A at 600 VAC;
50 A at 28 VDC
50 A at 300 VAC;
12 A at 480 VAC;
10 A at 600 VAC;
50 A at 28 VDC
Motor 2 HP at 120 to 600 VAC
Tungsten 15 A at 120 VAC
Pilot duty A600
Minimum switching requirement 1 A at 5 VAC/VDC
COIL CHARACTERISTICS
Voltage range 6 to 600 VAC; 6 to 250 VDC
Operating range (% of Nominal) 85% to 110% (AC); 80% to 110% (DC)
Average power consumption (Maximum) 10 VA; 4 W
Drop-out voltage threshold 10% (AC/DC)
PERFORMANCE CHARACTERISTICS
Electrical life (IEC 60947-1) Rated resistive load Please refer to Table 3
Operating time (response time) 30 ms
Dielectric strength Between coil and
contact
2200 V 2200 V 2200 V 2200 V
Between poles 2200 V N/A 2200 V N/A
Between open contacts 1600 V 2200 V 1600 V 2200 V
ENVIRONMENT
Product certifications UL, CSA, CE, RoHS
Ambient temperature range (around the device) -55 to +100 °C (Storage)
-55 to +55 °C (Operation)
Termination³ 10 (5.3) AWG (mm²)
Terminal tightening torque 11 to 15 in-lb (1.2 to 1.7 Nm)
Weight 227 to 312 g (8 to 11 oz)
––––––––
¹ For auxiliary switch ratings, please refer to Table 1.
² For ratings with blowout magnet, please refer to Table 2.
³ For UL listed installations, proper wire rating and terminations required.
4 Recommended ring, fork, or box wire termination.
199 Power Relays
GENERAL SPECIFICATIONS
168986 IEC 60947-1
DPDT SPDT SPST-DM
File No. E43641
File No. E43641
Power Relays
www.magnecraft.com
Document No. 600SP02-0710 ©2010 Schneider Electric USA.
Table 1: Auxiliary Switch Ratings
AUXILIARY SWITCH RATINGS
Resistive Load 120/250 VAC (50/60 Hz) 10 A
Motor Load 125/250 VAC (50/60 Hz) 0.25 HP
Tungsten Load 125 VAC (50/60 Hz) 3 A
Table 2: Additional DC Ratings with Blowout Magnets
RELAY VOLTAGE RATING W/BLOWOUT MAGNET
110 VDC 20 A
220 VDC 8 A
325 VDC 4 A
500 VDC 2 A
Table 3: Contact Ratings & Electrical Endurance (per IEC 60947-1, 60947-4-1)
CURRENT/HORSEPOWER
RATINGS LOAD VOLTAGE FREQUENCY LOAD TYPE ESTIMATED ELECTRICAL
ENDURANCE SEE NOTE(S)
AC LOAD
50 A 300 V 50/60 Hz Resistive 25,000 cycles 1, 4
40 A 50,000 cycles 2, 4
2 HP 120 to 600 V Motor 50,000 cycles 3, 4
15 A 120 V Tungsten 20,000 cycles 4, 5
A600 --- --- Pilot Duty 100,000 cycles 4
DC LOAD
40 A 28 V DC Resistive 100,000 cycles 4
20 A 110 V
8 A 220 V
4 A 325 V
2 A 500 V
SPST-NO-DM
SPST-NC-DB
SPDT
DPST-NC
DPDT
DPST-NO
22
12
A1
A2 11
2124
14
22 A1
A2 11
21
12
A1
A2 11
2124
14
14
12
A1
A2 11
A1
A2
12
13
A1
A2
14
13
Power Relays
www.magnecraft.com
Document No. 600SP02-0710 ©2010 Schneider Electric USA.
shown in inches (millimeters)
RELAY DIMENSIONS RELAY WIRING DIAGRAMS
Notes:
1. 50 A rating refer to models with pressure wire
connectors only.
2. Resistive AC load ratings are based on a power
factor of 0.85 to 1.0.
3. Motor horsepower ratings are based on a power
factor of 0.4 to 0.5, and an initial inrush current not
in excess of six times the full load current.
4. All ratings are based on applying the rated nominal
power to the relay coil in such a manner as to
provide a “clean” make and break, and does not
result in any contact chatter or multiple actuation
of the contacts.
5. The tungsten rating is based on cold filament
inrush current not exceeding 15 times the rated
steady state lamp current.
1.874
(47.60)
2.5
(63.6)
0.374
(9.50)
0.19
(4.8)
3.13
(79.4)
1.15
(29.3)
2.31
(58.8) 1.98
(50.3)
2.56
(65.0)
2.5
(63.6)
1.874
(47.60)
2.49
(63.2)
1.95
(49.6)
2.5
(63.6)
1.874
(47.60)
2.5
(63.6)
2.06
(52.4)
2.49
(63.2)
1.15
(29.3)
1.874
(47.60) 0.374
(9.50)
0.31
(8.0)
0.81
(20.7)
0.19
(4.8)
SPDT – Short base w/Auxiliary Switch DPST-NO
SPST-NO-DM
DPDT – Long base w/Auxiliary Switch
