WL50S Stainless Steel High-Intensity Work Spot Light Datasheet Chemically Resistant LED work lighting * * * * * * * Three lens options, depending on model, to vary spot size Illuminates a large area with an even pattern of light and no shadows 12 to 30V dc operation 56 mm (2.2 in) diameter with flat profile and 30 mm (1.2 in) mounting base Rugged, Viton(R) o-ring sealed housing rated to IP69K Chemically resistant 316 stainless steel housing for use in harsh environments FDA grade silicone gasket WARNING: Not To Be Used for Personnel Protection Never use this device as a sensing device for personnel protection. Doing so could lead to serious injury or death. This device does not include the self-checking redundant circuitry necessary to allow its use in personnel safety applications. A sensor failure or malfunction can cause either an energized or de-energized sensor output condition. Models Lux Model LED Color WL50SWSSL5Q WL50SWSSGL11Q Glass White, 5000-8300 K Polycarbonate Glass WL50SWSSL20Q Polycarbonate WL50SWSSGL20Q Glass P/N 168649_web Rev. C Lumens 0.5 m 1 m Polycarbonate WL50SWSSGL5Q WL50SWSSL11Q Window Material Lens Angle (see Beam Patterns on page 2) Connection 5 295 13780 3445 285 5460 1365 270 2000 500 13 November 2013 small, more focused spot 11 larger spot 20 largest spot 5 pin Euro integral QD connector (use with a 4-wire or 5-wire mating cordset, only 2 wires used for connection) WL50S Stainless Steel High-Intensity Work Spot Light Specifications Supply Voltage and Current Operating Voltage: 12 to 30V dc Current Draw: 400 mA max. Environmental Rating IEC IP67, IP69K per DIN 40050-9 NOTE: Do not spray the cable with a high-pressure sprayer or cable damage will result. Supply Protection Circuitry Protected against reverse polarity and transient voltages Light Source Three high-intensity LEDs; see models table for color temperature Operating Conditions -20 to +50C (-4 to +122F) 95% max. relative humidity (non-condensing) Useful Life When operating within specifications, output will decrease less than 30% after 50,000 hours. Vibration and Mechanical Shock All models meet Mil. Std. 202F requirements method 201A (vibration: 10 to 60 Hz max., double amplitude 0.06", maximum acceleration 10G). Also meets IEC 947-5-2; 30G 11 ms duration, half sine wave. Construction 316 stainless steel housing, polycarbonate or glass window with Viton seal, 316 stainless steel M30 mounting nut, FDA grade silicon base gasket Storage Temperature -40 C to +70 C (-40 F to +158 F) 95% maximum relative humidity (non-condensing) Mounting 30x1.5 mm thread base mount Certifications Approvals are pending Connections Integral 5-pin M12/Euro style QD; 4-pin connecting cordset required for QD models; only 2 wires used Beam Patterns 100% 75% 50% 25% 5 11 20 0% -30 -20 -10 0 10 20 Light Pattern From Center (cm) 2 30 Percentage of Maximum Light Intensity Per Lens Type at 1 Meter (Typical) Perce ntage of Max Light Intensity (Lux or mW/cm %) Perce ntage of Max Light Intensity (Lux or mW/cm %) Percentage of Maximum Light Intensity Per Lens Type at 0.5 Meter (Typical) 100% 75% 50% 25% 5 20 11 0% -60 -50 -40 -30 -20 -10 0 10 20 30 40 50 60 Light Pattern From Center (cm) www.bannerengineering.com - tel: 763-544-3164 P/N 168649_web Rev. C WL50S Stainless Steel High-Intensity Work Spot Light Dimensions Wiring Female 1 Wiring Key: 1 = Brown 3 = Blue 1 3 1 = Brown Male 3 = Blue 12 - 30V dc 3 1 3 Cordsets Standard Cordsets 4-Pin Threaded M12/Euro-Style Cordsets Model Length MQDC-406 1.83 m (6 ft) MQDC-415 4.57 m (15 ft) MQDC-430 9.14 m (30 ft) MQDC-450 15.2 m (50 ft) Style Dimensions Pinout 44 Typ. Straight M12 x 1 o 14.5 www.bannerengineering.com - tel: 763-544-3164 3 4 1 2 3 4 P/N 168649_web Rev. C 2 1 = = = = Brown White Blue Black 3 WL50S Stainless Steel High-Intensity Work Spot Light 4-Pin Threaded M12/Euro-Style Cordsets Model Length MQDC-406RA 1.83 m (6 ft) MQDC-415RA 4.57 m (15 ft) MQDC-430RA 9.14 m (30 ft) MQDC-450RA 15.2 m (50 ft) Style Dimensions Pinout 32 Typ. [1.26"] 30 Typ. [1.18"] Right-Angle M12 x 1 o 14.5 [0.57"] Washdown Rated Cordsets Polypropylene jacket and connector body, stainless steel coupling nut 5-Pin Threaded M12/Euro-Style CordsetsWashdown Model Length MQDCWD-506 1.83 m (6 ft) Style Dimensions Pinout 2 1 42 Typ. [1.65"] 3 4 o 15.0 [0.57"] Straight MQDCWD-530 5 9.14 m (30 ft) 1 = Brown 2 = White M12 x 1 3 = Blue 4 = Black 5 = Gray Mounting Brackets All measurements are in mm SMB30A * Right-angle bracket with curved slot for versatile orientation * Clearance for M6 (1/4 in) hardware * Mounting hole for 30 mm sensor * 12-ga. stainless steel Hole center spacing: A to B=40 Hole size: A=o 6.3, B= 27.1 x 6.3, C=o 30.5 4 45 C 61 B A 69 SMB30SC * Swivel bracket with 30 mm mounting hole for sensor * Black reinforced thermoplastic polyester * Stainless steel mounting and swivel locking hardware included 67 B 58 29 A Hole center spacing: A=o 50.8 Hole size: A=o 7.0, B=o 30.0 www.bannerengineering.com - tel: 763-544-3164 P/N 168649_web Rev. C WL50S Stainless Steel High-Intensity Work Spot Light SMB30FA * Swivel bracket with tilt and pan movement for precise adjustment * Mounting hole for 30 mm sensor * 12-ga. 304 stainless steel * Easy sensor mounting to extrude rail T-slot * Metric and inch size bolt available 83.2 36.3 68.9 B A SMBAMS30RA * Right-angle SMBAMS series bracket * 30 mm hole for mounting sensors * Articulation slots for 90+ rotation * 12-ga. (2.6 mm) cold-rolled steel 45 C 53 A B 48 Hole center spacing: A=26.0, A to B=13.0 Hole size: A=26.8 x 7.0, B=o 6.5, C=o 31.0 Bolt thread: SMB30FA, A= 3/8 - 16 x 2 in; SMB30FAM10, A= M10 1.5 x 50 Hole size: B= o 30.1 SMB30MM * 12-ga. stainless steel bracket with curved mounting slots for versatile orientation * Clearance for M6 (1/4 in) hardware * Mounting hole for 30 mm sensor 57 70 C 57 Hole center spacing: A = 51, A to B = 25.4 Hole size: A = 42.6 x 7, B = o 6.4, C = o 30.1 B A SMBAMS30P * Flat SMBAMS series bracket * 30 mm hole for mounting sensors * Articulation slots for 90+ rotation * 12-ga. 300 series stainless steel 45 C 93 A B Hole center spacing: A=26.0, A to B=13.0 Hole size: A=26.8 x 7.0, B=o 6.5, C=o 31.0 Banner Engineering Corp Limited Warranty Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty period. This warranty does not cover damage or liability for misuse, abuse, or the improper application or installation of the Banner product. THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE OF DEALING OR TRADE USAGE. This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING CORP. BE LIABLE TO BUYER OR ANY OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY PRODUCT DEFECT OR FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE. Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligations or liabilities relating to any product previously manufactured by Banner Engineering Corp. www.bannerengineering.com - tel: 763-544-3164