Common Mode Choke Electrical Characteristics (at 25C) L1-4 1kHz 0.25V 15H +50% -35% L2-3 L1-4-L2-3 2H (Max.) DCR1-4 at 25C 35m (Max.) DCR2-3 100MHz Z 350 (Typical) Coil-Coil DC 1,000 2mA Hi-pot 3S (Min.) Rated Current 500mA (Max.) Rated Voltage 50V (Typical) 1kHz 0.25V Operating temperature: -20C to +85C Configurations and Dimensions A 8.3 0.5mm B 7 0.5mm C 10 0.5mm D 5 0.5mm Dimensions : Millimetres Test Data for Mechanical Test Item A mm B mm C mm D mm Specification 8.3 0.5 7 0.5 10 0.5 5 0.5 1 8.35 7.02 10.01 4.93 2 8.36 7.06 10.33 4.98 3 8.29 7.03 10.06 4.95 4 8.32 7.02 10.02 4.9 5 8.31 7.04 10.12 4.95 Average 8.33 7.03 10.11 4.94 www.element14.com www.farnell.com www.newark.com Page <1> 08/04/14 V1.0 Common Mode Choke Schematic Diagram Note: 1-4.Wire O0.3mm x 1P 2UEWF 155C x 5TS (Reference) 2-3.Wire O0.3mm x 1P 2UEWF 155C x 5TS (Reference) Test Data for Electrical Test Item L1-4 H L2-3 H L1-4-L2-3 H DCR1-4 m DCR2-3 m Z Hi-pot S Condition 1KHz 0.25V 1KHz 0.25V 1KHz 0.25V at 25C at 25C 100MHz Coil-Coil DC 1,000 2mA Specification 15 +50% -35% 15 +50% -35% 2 (Max.) 35 (Max.) 35 (Max.) 350 (Typical) 3 (Min.) 1 17.8 17.7 14.67 14.4 191.1 OK 2 15.8 15.7 14.64 14.43 193.5 OK 3 16.6 16.5 13.93 14.29 194.8 OK 4 14.2 14.2 0 14.4 14.87 182.5 OK 5 17.1 17 0.1 14.64 14.41 193.4 OK Average 16.3 16.22 0.08 14.46 14.48 191.06 OK 0.1 Electric Characteristics www.element14.com www.farnell.com www.newark.com Page <2> 08/04/14 V1.0 Common Mode Choke Reliability Test Test Item Specifications Test Method and Remarks Operating temperature range -20C to +85C Including temperature rise due to self-generated heat Storage condition Ambient temperature : 0C to 40C Humidity : Below 70%RH To maintain the solderability of terminal electrodes, care must be taken to control temperature and humidity in the storage area. Moisture sensitivity Appearance : N o abnormality No damage DCR change : Within 20% Inductance change : Within 20% According to J-STD-020B level 3 Test condition : 60C 60% RH Test duration : 40 hours Recovery : 1 to 2 hours of recovery under the standard condition after the removal from the test chamber. Solderability All termination shall exhibit a continuous solder coating free from defects for a minimum of 90% of the surface area of any individual lead. According to J-STD-002B Steam aging category : 97C 98% RH Steam aging duration : 8 hours Solder : Lead-free solder Solder temperature : 260 5C Dip time : 5 +0/-0.5 seconds. Material List No. Item Material Description 1 Core S2K T4.3 x 2.5 x 2.8 2 Wire O0.3mm x 2P 2UEWF 155C 3 Solder (Lead Free) Sn99.3%Cu0.7% 4 Base BG406-1 LCP4008 Part Number Table Description Part Number Choke, common mode, 15H, 0.5A MCBS3019P-150U Important Notice : This data sheet and its contents (the "Information") belong to the members of the Premier Farnell group of companies (the "Group") or are licensed to it. No licence is granted for the use of it other than for information purposes in connection with the products to which it relates. No licence of any intellectual property rights is granted. The Information is subject to change without notice and replaces all data sheets previously supplied. The Information supplied is believed to be accurate but the Group assumes no responsibility for its accuracy or completeness, any error in or omission from it or for any use made of it. Users of this data sheet should check for themselves the Information and the suitability of the products for their purpose and not make any assumptions based on information included or omitted. Liability for loss or damage resulting from any reliance on the Information or use of it (including liability resulting from negligence or where the Group was aware of the possibility of such loss or damage arising) is excluded. This will not operate to limit or restrict the Group's liability for death or personal injury resulting from its negligence. Multicomp is the registered trademark of the Group. (c) Premier Farnell plc 2012. www.element14.com www.farnell.com www.newark.com Page <3> 08/04/14 V1.0