PE30 www.vishay.com Vishay Sfernice Fully Sealed Potentiometer Professional Grade FEATURES * High power rating 3 W at 70 C * Low temperature coefficient (150 ppm/C typical) * Cermet element * Full sealing DESIGN SUPPORT TOOLS * Use of faston 2.86 connections click logo to get started * Tests according to CECC 41000 or IEC 60393-1 * Wires and connectors available Models * Custom design on request Available QUICK REFERENCE DATA * Center detent option Multiple module Switch module Detent module * Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 No n/a Yes A: linear, L: logarithmic, F: reverse logarithmic IP 67 25K cycles Special electrical laws Sealing level Lifespan DIMENSIONS in millimeters (inches) 0.5 mm ( 0.02") PE30L 8 (0.31) 20 (0.79) max. 12 (0.47) 76 14 wrench 13 (0.51) max. Thread M10 x 0.75 O6 (0.24) 0.5 (0.02) FG = 16 (0.63) O 19.7 (0.78) a FL = 25 (0.99) FR = 50 (1.97) 3 (0.12) PE30LL: LPRP - Locating Peg c R 5.2 (0.20) 3 (0.12) b 2.85 (0.11) 0.8 (0.3) O 1.8 (0.07) O 10.5 (0.41) 12.5 (0.49) 9.2 (0.36) PANEL MOUNT 8.8 (0.35) O 3.5 (0.14) 3 (0.12) 2.3 (0.9) 23 (0.91) max. PE30ME: Panel Sealed 16 (0.63) max. Sealing ring 0.7 (0.03) O 1.2 (0.05) O 1 (0.4) Flats located 8 0.2 (0.31 0.01) O 10.5 (0.41) Revision: 01-Feb-18 O6 (0.24) O 19.7 (0.78) 9 (0.35) FD = 13 (0.61) PANEL MOUNT Slot 1 x 1.8 deep FJ = 22 (0.87) FP = 47 (1.85) Document Number: 51037 1 For technical questions, contact: sferpottrimmers@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 PE30 www.vishay.com Vishay Sfernice ELECTRICAL SPECIFICATIONS Resistive element Cermet Electrical travel Resistance range 270 10 22 to 10 M linear taper 100 to 2.2 M logarithmic taper Standard series E3 Tolerance 1 - 2.2 - 4.7 and on request 1 - 2 - 5 standard 20 % on request 10 % to 5 % % TOTAL RESISTANCE 100 Taper 80 F 60 A L 40 20 0 0 20 40 60 80 100 % CLOCKWISE SHAFT ROTATION 3 Power rating linear logarithmic POWER IN W LIN. TAPER A 3 W at 70 C 1.5 W at 70 C 2 LOG. TAPER L and F 1 0 0 20 40 60 70 80 100 120 140 AMBIENT TEMPERATURE IN C Circuit diagram a c (1) (3) cw b (2) Temperature coefficient (typical) Limiting element voltage Contact resistance variation (typical) End resistance (typical) 150 ppm/C 300 V 3 % Rn or 3 1 Dielectric strength (RMS) 2500 V Insulation resistance (300 VDC) 105 M Independent linearity (typical) 5% Revision: 01-Feb-18 Document Number: 51037 2 For technical questions, contact: sferpottrimmers@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 PE30 www.vishay.com Vishay Sfernice STANDARD RESISTANCE ELEMENT DATA STANDARD RESISTANCE VALUES LINEAR TAPER MAX. POWER AT 70 C LOGS TAPER MAX. WORKING VOLTAGE MAX. CUR. THROUGH WIPER MAX. POWER AT 70 C MAX. WORKING VOLTAGE MAX. CUR. THROUGH WIPER W V mA 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 0.9 0.41 0.19 0.09 0.04 12.2 18.2 26.6 38.7 57.4 83.9 122 181.6 265 300 300 300 300 300 122 82.6 56.6 38.7 26.1 17.9 12.2 8.25 5.64 3 1.36 0.63 0.30 0.13 W V mA 22 47 100 220 470 1K 2.2K 4.7K 10K 22K 47K 100K 220K 470K 1M 2.2M 4.7M 10M 3 3 3 3 3 3 3 3 3 3 1.91 0.90 0.41 0.19 0.09 0.04 0.02 0.01 8.1 11.9 17.3 25.7 37.5 54.8 81.2 119.9 173 257.7 300 300 300 300 300 300 300 300 369 252 173 116 79 54 37 25 17 11 6.3 3 1.36 0.63 0.30 0.13 0.06 0.03 MECHANICAL SPECIFICATIONS Mechanical travel 300 5 Operating torque / typical value 3 Ncm 4.25 oz.-inch End stop torque 120 Ncm max. 10.51 lb oz.-inch max. Tightening torque of mounting nut 250 Ncm max. 22 lb-inch max. Unit weight 23 g to 32 g max. Terminals 0.8 oz. to 1.13 oz. e3: pure Sn ENVIRONMENTAL SPECIFICATIONS Temperature range -55 C to +125 C Climatic category 55/125/56 Sealing Fully sealed - container IP67 OPTIONS Special feature command shaft Length is measured from the mounting surface to the free end of the shaft. The screwdriver slot is aligned with the wiper within 10. Special shafts are available, in accordance to drawings supplied by customers. We recommend that customers should not machine tool shafts, in order to avoid damage. Bending or torsion of terminals should also be avoided. Panel sealing (PE30M) The panel sealing device consists of a ring located in a groove on the potentiometer face. Sealing is obtained by tightening the ring against the panel when mounting the potentiometer. Old code: PE30P Locating peg (PE30LL) Location is obtained by fitting a special washer on the mounting face of the potentiometer. Old code: LPRP The shaft locking device consists of a tapered nut tightening a slotted notched washer against both bushing and shaft. DBAN tightening torque is 200 Ncm, shaft locking torque being 30 Ncm. DBAN is also available with all special types. This device is normally supplied in a separate bag. Can be pre-mounted on request. 1) Shaft locking (PE30LD) 2) 14 wrench 12 wrench Assembling Method 6.5 15 Revision: 01-Feb-18 Document Number: 51037 3 For technical questions, contact: sferpottrimmers@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 PE30 www.vishay.com Vishay Sfernice CENTER DETENT * Stable position in mid mechanical travel * Output ratio 50 % 10 % * Rotational life: 10 000 actuations Full CW Full CCW ORDERING INFORMATION (First order only) CV1M MARKING * * * * Vishay trademark Part number (including ohmic value and tolerance code) Manufacturing date code Marking of terminals 3, and a, b, c PERFORMANCE TESTS CONDITIONS TYPICAL VALUES AND DRIFTS RT/RT (%) R1-2/R1-2 (%) OTHER Electrical endurance 1000 h at rated power 90'/30' - ambient temp. 70 C 1% - Contact res. variation: < 3 % Rn Climatic sequence Phase A dry heat 125 C Phase B damp heat Phase C cold -55 C Phase D damp heat 5 cycles 0.5 % 1% - Damp heat, steady state 56 days 40 C 93 % HR 0.5 % 1% Insulation resistance: > 104 M Change of temperature 5 cycles -55 C at +125 C 0.5 % - - Mechanical endurance 25 000 cycles 3% - Contact res. variation: < 2 % Rn 50 g's at 11 ms 3 successive shocks in 3 directions 0.1 % 0.2 % - 10 Hz to 55 Hz 0.75 mm or 10 g's during 6 h 0.1 % 0.2 % - Shock Vibration Note * Nothing stated herein shall be construed as a guarantee of quality or durability Revision: 01-Feb-18 Document Number: 51037 4 For technical questions, contact: sferpottrimmers@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 PE30 www.vishay.com Vishay Sfernice ORDERING INFORMATION (part number) P E 3 MODEL BUSHING PE30 0 L OPTION B F G 2 0 OHMIC VALUE SHAFT A law = For L bushing (= old codes:) from 22 FG 16 mm, slotted = AC to 10 M FL 25 mm, slotted = AM For L bushing FR 50 mm, plain = AL D = DBAN M = panel L and F L = LPRP sealed laws = For M bushing B = DBAN M10 x 0.75 FD = 13 mm, slotted = AC from 100 and LPRP to 2.2 M FJ = 22 mm, slotted = AM FP = 47 mm, plain = AL For M bushing E = peg A = peg and DBAN 0 = none L= M10 x 0.75 4 M A B TOLERANCE TAPER PACKAGING M = 20 % On request: K = 10 % J=5% A = linear L = clockwise logarithmic F = clockwise inverse logarithmic B = box of 10 pieces SPECIAL NUMBER (if applicable) Given by Vishay for custom design or E105 CV1M PART NUMBER DESCRIPTION (for information only) PE30 LPRP AC 200K 20 % A DBAN CV1M BO MODEL FEATURES OPTION SHAFT VALUE TOL. TAPER OPTION SPECIAL DETENT PACKAGING e3 CUSTOM LEAD SPECIAL SHAFT (Pb)-FREE RELATED DOCUMENTS APPLICATION NOTES Potentiometers and Trimmers www.vishay.com/doc?51001 Guidelines for Vishay Sfernice Resistive and Inductive Components www.vishay.com/doc?52029 Revision: 01-Feb-18 Document Number: 51037 5 For technical questions, contact: sferpottrimmers@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, "Vishay"), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. (c) 2017 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED Revision: 08-Feb-17 1 Document Number: 91000