For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
POWER DETECTORS - SMT
11
11 - 1
HMC713LP3E
General Description
Features
Functional Diagram
The HMC713LP3E Logarithmic Detector/Controller
is ideal for converting the power of RF signals with
frequencies in the 50 MHz to 8000 MHz range, to a
DC voltage, proportional to input power, at its output.
The HMC713LP3E employs a successive compression
technology which delivers 54 dB of dynamic range
with high measurement accuracy over a wide input
frequency range. As the input signal is increased,
successive ampliers move into saturation one by one
creating an accurate approximation of the logarithm
function. The outputs of a series of detectors are
summed, converted into voltage domain and buffered
to drive the OUTP output.
For detection mode, the OUTP pin is connected to
the VSET input and will provide a nominal logarithmic
slope of 17 mV/dB and an intercept of -68 dBm. The
HMC713LP3E can also be used in the controller mode
where an external voltage is applied to the VSET pin to
create an AGC or APC feedback loop.
Wide Dynamic Range: up to 54 dB
High Accuracy:
±1 dB with 54 dB Range Up To 2.7 GHz
Fast Output Response Time
Supply Voltage: +2.7 to +5.5V
Power-Down Mode
Excellent Stability over Temperature
16 Lead 3x3 mm SMT Package: 9mm
Typical Applications
The HMC713LP3E is ideal for:
• Cellular Infrastructure
• WiMAX, WiBro & LTE/4G
• Power Monitoring & Control Circuitry
• Receiver Signal Strength Indication (RSSI)
• Automatic Gain & Power Control
• Military, ECM & Radar
Electrical Specications, TA = +25 °C, Vcc = +3V, EN = +3V [1]
54 dB, LOGARITHMIC
DETECTOR / CONTROLLER, 50 - 8000 MHz
v01.1009
Parameter Typ. Typ. Typ. Typ. Typ. Typ. Typ. Typ. Typ. Typ. Units
Input Frequency 50 100 500 900 1900 2700 3900 5800 7000 8000 MHz
±3 dB Dynamic Range 61 61 61 62 62 61 58 50 44 40 dB
±3 dB Dynamic Range Center -27 -27 -27 -28 -28 -28 -26 -23 -20 -17 dBm
±1 dB Dynamic Range 54 53 53 54 55 54 49 39 33 31 dB
OUTP Slope 17.2 17.2 17.2 17.1 17 17.2 18.3 21.2 23.8 25.5 mV/dB
OUTP Intercept -67.9 -68.1 -68.6 -68.9 -69.5 -69.2 -65.3 -55.9 -48.8 -44.2 dBm
Variation of OUTP with Temperature
from -40°C to +85°C @ -20 dBm Input -1.3 -1.3 -1.2 -1.2 -1.1 -1.1 -1.2 -2.1 -2.8 -3.5 dB
[1] Detector mode measurements; OUTP (Pin 13) is connected to VSET (Pin 7) through an RC network.
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
For price, delivery, and to place orders: Analog Devices, Inc.,
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
Phone: 781-329-4700 • Order online at www.analog.com
Application Support: Phone: 1-800-ANALOG-D
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
POWER DETECTORS - SMT
11
11 - 2
Electrical Specications, (continued)
HMC713LP3E
v01.1009 54 dB, LOGARITHMIC
DETECTOR / CONTROLLER, 50 - 8000 MHz
Parameter Conditions Min. Typ. Max. Units
Power Down (EN) Input
Voltage Range for Normal Mode 0.8 x Vcc Vcc/2 V
Voltage Range for Powerdown Mode Vcc/2 0.2 x Vcc V
Power Supply (Vcc)
Operating Voltage Range 2.7 - 5.5 V
Supply Current in Normal Mode EN Input at Vcc 17 mA
Supply Current in Power Down Mode EN Input at GND 0.4 mA
OUTP Output
Rise Time CLPF= 0, No Power to -10 dBm, 10% - 90% 24 ns
Fall Time CLPF= 0, -10 dBm to No Power, 90% - 10% 36 ns
Output Video BW 50mV reduction in output voltage swing
(3 dB referred to the input) [1] 16 MHz
Voltage Range Closed Loop (Eval Board Setup) 0.2 - 1.2 V
Voltage Range Open Loop 0.1 to
(Vcc -0.1) V
Current Drive Source / Sink 4.2 / 0.48 mA
OUTN Output
Current Drive Source / Sink 4.0 / 0.43 mA
Output Voltage Range 0.2 - 2.1 V
RF Input
Input Return Loss (S11) F= 50 MHz to 8 GHz
Z0= 50, See plot 10 dB
VSET Input
Input Impedance 1 M
Input Voltage Range Eval Board 0.2 - 1.2 V
Low Frequency Gain VSET to OUTP 64 dB
Open Loop Corner Frequency 11 kHz
[1] Two tone test: Frequency = 900 MHz, Tone 1 Power = -20 dBm, Tone 2 Power = -28 dBm
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
For price, delivery, and to place orders: Analog Devices, Inc.,
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
Phone: 781-329-4700 • Order online at www.analog.com
Application Support: Phone: 1-800-ANALOG-D
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
POWER DETECTORS - SMT
11
11 - 3
Output Voltage & Error
vs. Input Power, Fin = 2700 MHz
Output Voltage & Error
vs. Input Power, Fin = 1900 MHz
HMC713LP3E
v01.1009 54 dB, LOGARITHMIC
DETECTOR / CONTROLLER, 50 - 8000 MHz
0
0.4
0.8
1.2
1.6
2
2.4
-6
-4
-2
0
2
4
6
-60 -50 -40 -30 -20 -10 0 10
OUTP Err +25C
OUTP Err +85C
OUTP Err -40C
OUTN Err +25C
OUTN Err +85C
OUTN Err -40C
OUT[P,N] (V)
ERROR (dB)
INPUT POWER (dBm)
OUTP
OUTN
0
0.4
0.8
1.2
1.6
2
2.4
-6
-4
-2
0
2
4
6
-60 -50 -40 -30 -20 -10 0 10
OUTP Err +25C
OUTP Err +85C
OUTP Err -40C
OUTN Err +25C
OUTN Err +85C
OUTN Err -40C
OUT[P,N] (V)
ERROR (dB)
INPUT POWER (dBm)
OUTP
OUTN
Output Voltage & Error
vs. Input Power, Fin = 500 MHz
Output Voltage & Error
vs. Input Power, Fin = 900 MHz
Output Voltage & Error
vs. Input Power, Fin = 50 MHz
Output Voltage & Error
vs. Input Power, Fin = 100 MHz
0
0.4
0.8
1.2
1.6
2
2.4
-6
-4
-2
0
2
4
6
-60 -50 -40 -30 -20 -10 0 10
OUTP Err +25C
OUTP Err +85C
OUTP Err -40C
OUTN Err +25C
OUTN Err +85C
OUTN Err -40C
OUT[P,N] (V)
ERROR (dB)
INPUT POWER (dBm)
OUTP
OUTN
0
0.4
0.8
1.2
1.6
2
2.4
-6
-4
-2
0
2
4
6
-60 -50 -40 -30 -20 -10 0 10
OUTP Err +25C
OUTP Err +85C
OUTP Err -40C
OUTN Err +25C
OUTN Err +85C
OUTN Err -40C
OUT[P,N] (V)
ERROR (dB)
INPUT POWER (dBm)
OUTP
OUTN
0
0.4
0.8
1.2
1.6
2
2.4
-6
-4
-2
0
2
4
6
-60 -50 -40 -30 -20 -10 0 10
OUTP Err +25C
OUTP Err +85C
OUTP Err -40C
OUTN Err +25C
OUTN Err +85C
OUTN Err -40C
OUT[P,N] (V)
ERROR (dB)
INPUT POWER (dBm)
OUTP
OUTN
0
0.4
0.8
1.2
1.6
2
2.4
-6
-4
-2
0
2
4
6
-60 -50 -40 -30 -20 -10 0 10
OUTP Err +25C
OUTP Err +85C
OUTP Err -40C
OUTN Err +25C
OUTN Err +85C
OUTN Err -40C
OUT[P,N] (V)
ERROR (dB)
INPUT POWER (dBm)
OUTP
OUTN
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
For price, delivery, and to place orders: Analog Devices, Inc.,
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
Phone: 781-329-4700 • Order online at www.analog.com
Application Support: Phone: 1-800-ANALOG-D
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
POWER DETECTORS - SMT
11
11 - 4
HMC713LP3E
v01.1009 54 dB, LOGARITHMIC
DETECTOR / CONTROLLER, 50 - 8000 MHz
Input Return Loss
-30
-20
-10
0
0 1 2 3 4 5 6 7 8 9 10
FREQUENCY (GHz)
RETURN LOSS (dB)
Output Voltage & Error
vs. Input Power, Fin = 3900 MHz
Output Voltage & Error
vs. Input Power, Fin = 7000 MHz
Output Voltage & Error
vs. Input Power, Fin = 5800 MHz
Output Voltage & Error
vs. Input Power, Fin = 8000 MHz
0
0.4
0.8
1.2
1.6
2
2.4
-6
-4
-2
0
2
4
6
-60 -50 -40 -30 -20 -10 0 10
OUTP Err +25C
OUTP Err +85C
OUTP Err -40C
OUTN Err +25C
OUTN Err +85C
OUTN Err -40C
OUT[P,N] (V)
ERROR (dB)
INPUT POWER (dBm)
OUTP
OUTN
0
0.4
0.8
1.2
1.6
2
2.4
-6
-4
-2
0
2
4
6
-50 -40 -30 -20 -10 0 10
OUTP Err +25C
OUTP Err +85C
OUTP Err -40C
OUTN Err +25C
OUTN Err +85C
OUTN Err -40C
OUT[P,N] (V)
ERROR (dB)
INPUT POWER (dBm)
OUTP
OUTN
0
0.4
0.8
1.2
1.6
2
2.4
-6
-4
-2
0
2
4
6
-50 -40 -30 -20 -10 0 10
OUTP Err +25C
OUTP Err +85C
OUTP Err -40C
OUTN Err +25C
OUTN Err +85C
OUTN Err -40C
OUT[P,N] (V)
ERROR (dB)
INPUT POWER (dBm)
OUTP
OUTN
0
0.4
0.8
1.2
1.6
2
2.4
-6
-4
-2
0
2
4
6
-40 -30 -20 -10 0 10
OUTP Err +25C
OUTP Err +85C
OUTP Err -40C
OUTN Err +25C
OUTN Err +85C
OUTN Err -40C
OUT[P,N] (V)
ERROR (dB)
INPUT POWER (dBm)
OUTP
OUTN
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
For price, delivery, and to place orders: Analog Devices, Inc.,
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
Phone: 781-329-4700 • Order online at www.analog.com
Application Support: Phone: 1-800-ANALOG-D
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
POWER DETECTORS - SMT
11
11 - 5
HMC713LP3E
v01.1009 54 dB, LOGARITHMIC
DETECTOR / CONTROLLER, 50 - 8000 MHz
OUTP Slope vs. Frequency OUTP Slope vs. Supply Voltage
15
17
19
21
23
25
27
012345678
+25C
+85C
-40C
FREQUENCY (GHz)
SLOPE (mV/dB)
15
17
19
21
23
25
27
2.7 3.1 3.5 3.9 4.3 4.7 5.1 5.5
0.05GHz
0.1GHz
0.5GHz
0.9GHz
1.9GHz
2.7GHz
5.8GHz
3.9GHz
7GHz
8GHz
SLOPE (mV/dB)
VOLTAGE SUPPLY (V)
OUTP vs. Frequency & Input Power OUTP Voltage & Error vs. Frequency
OUTP Intercept vs. Supply Voltage
OUTP Intercept vs. Frequency
0
0.3
0.6
0.9
1.2
1.5
1.8
-6
-4
-2
0
2
4
6
-60 -50 -40 -30 -20 -10 0 10
0.05GHz
0.1GHz
0.5GHz
0.9GHz
1.9GHz
2.7GHz
3.9GHz
5.8GHz
7GHz
8GHz
OUTP (V)
ERROR (dB)
INPUT POWER (dBm)
OUTP
ERROR
0
0.2
0.4
0.6
0.8
1
1.2
1.4
01234 5678
FREQUENCY (GHz)
OUTP (V)
0dBm
-10dBm
-20dBm
-30dBm
-40dBm
-50dBm
-60dBm
-90
-80
-70
-60
-50
-40
01234 5678
+25C
+85C
-40C
FREQUENCY (GHz)
INTERCEPT (dBm)
-80
-70
-60
-50
-40
2.7 3.1 3.5 3.9 4.3 4.7 5.1 5.5
0.05GHz
0.1GHz
0.5GHz
0.9GHz
1.9GHz
2.7GHz
3.9GHz
5.8GHz
7GHz
8GHz
INTERCEPT (dBm)
VOLTAGE SUPPLY (V)
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
For price, delivery, and to place orders: Analog Devices, Inc.,
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
Phone: 781-329-4700 • Order online at www.analog.com
Application Support: Phone: 1-800-ANALOG-D
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
POWER DETECTORS - SMT
11
11 - 6
Output Response Rise Time [1] C1 = Open Output Response Rise Time [1] C1 = 10nF
0
0.3
0.6
0.9
1.2
1.5
0 50 100 150 200 250 300 350 400 450 500
10 dBm
0 dBm
-10 dBm
-20 dBm
-30 dBm
TIME (ns)
OUTP (V)
0
0.3
0.6
0.9
1.2
1.5
0 10 20 30 40 50 60 70 80 90 100
10 dBm
0 dBm
-10 dBm
-20 dBm
-30 dBm
TIME (us)
OUTP (V)
Output Response [1] Fall Time C1 = Open Output Response Fall Time [1] C1 = 10nF
0
0.3
0.6
0.9
1.2
1.5
0 50 100 150 200 250 300 350 400 450 500
10 dBm
0 dBm
-10 dBm
-20 dBm
-30 dBm
TIME (ns)
OUTP (V)
0
0.3
0.6
0.9
1.2
1.5
0 25 50 75 100 125 150 175 200
10 dBm
0 dBm
-10 dBm
-20 dBm
-30 dBm
TIME (us)
OUTP (V)
HMC713LP3E
v01.1009 54 dB, LOGARITHMIC
DETECTOR / CONTROLLER, 50 - 8000 MHz
[1] 900 MHz, Switched CW-Tone
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
For price, delivery, and to place orders: Analog Devices, Inc.,
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
Phone: 781-329-4700 • Order online at www.analog.com
Application Support: Phone: 1-800-ANALOG-D
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
POWER DETECTORS - SMT
11
11 - 7
Absolute Maximum Ratings
Vcc 0 to +5.6V
EN Input Voltage 0 to +5.6V
VSET Input Voltage 0 to +5.6V
OUTP Output Current 5 mA
OUTN Output Current 5 mA
RF Input Power 12 dBm
Junction Temperature 125 °C
Continuous Pdiss (T = 85°C)
(Derate 5.43 mW/°C above 85°C) 0.22 Watts
Thermal Resistance (Rth)
(junction to lead) 184 °C/W
Storage Temperature -65 to +150 °C
Operating Temperature -40 to +85 °C
ESD Sensitivity (HBM) Class 1C
ELECTROSTATIC SENSITIVE DEVICE
OBSERVE HANDLING PRECAUTIONS
Package Information
Outline Drawing
Part Number Package Body Material Lead Finish MSL Rating Package Marking [1]
HMC713LP3E RoHS-compliant Low Stress Injection Molded Plastic 100% matte Sn MSL1 [2] 713
XXXX
[1] 4-Digit lot number XXXX
[2] Max peak reow temperature of 260 °C
NOTES:
1. LEADFRAME MATERIAL: COPPER ALLOY
2. DIMENSIONS ARE IN INCHES [MILLIMETERS].
3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE
4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM.
PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM.
5. PACKAGE WARP SHALL NOT EXCEED 0.05mm.
6. ALL GROUND LEADS AND GROUND PADDLE
MUST BE SOLDERED TO PCB RF GROUND.
7. REFER TO HMC APPLICATION NOTE FOR SUGGESTED PCB LAND PATTERN.
HMC713LP3E
v01.1009 54 dB, LOGARITHMIC
DETECTOR / CONTROLLER, 50 - 8000 MHz
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
For price, delivery, and to place orders: Analog Devices, Inc.,
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
Phone: 781-329-4700 • Order online at www.analog.com
Application Support: Phone: 1-800-ANALOG-D
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
POWER DETECTORS - SMT
11
11 - 8
Pin Number Function Description Interface Schematic
1, 4 N/C These pins are not connected internally.
2, 5, 9 - 12 GND These pins and package bottom must be connected to
RF/DC ground.
3 RFIN RF input pin.
6 EN
Enable pin.
Apply VEN >0.8 x Vcc for normal operation.
Apply VEN <0.2xVcc to disable the HMC713LP3E and
reduce supply current to 0.4mA.
7 VSET
Set point input for controller mode.
Connect to OUTP with the resistor network shown in
evaluation board drawing for detector mode.
8 CLPF Connection for ground referenced external lowpass
lter capacitor.
Pin Descriptions
HMC713LP3E
v01.1009 54 dB, LOGARITHMIC
DETECTOR / CONTROLLER, 50 - 8000 MHz
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
For price, delivery, and to place orders: Analog Devices, Inc.,
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
Phone: 781-329-4700 • Order online at www.analog.com
Application Support: Phone: 1-800-ANALOG-D
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
POWER DETECTORS - SMT
11
11 - 9
Pin Number Function Description Interface Schematic
13 OUTP
Logarithmic output that converts the input power to a
DC level in controller mode. Output voltage increases
with increasing amplitude
14 OUTN Inverted logarithmic output.
OUTN= 2.55 - 2 x OUTP
15, 16 Vcc Bias Supply. Connect supply voltage
to these pins with appropriate ltering.
Pin Descriptions (Continued)
HMC713LP3E
v01.1009 54 dB, LOGARITHMIC
DETECTOR / CONTROLLER, 50 - 8000 MHz
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
For price, delivery, and to place orders: Analog Devices, Inc.,
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
Phone: 781-329-4700 • Order online at www.analog.com
Application Support: Phone: 1-800-ANALOG-D
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
POWER DETECTORS - SMT
11
11 - 10
Application & Evaluation PCB Schematic
Notes
Note 1: The HMC713LP3E evaluation board is pre-assembled for single-ended input, and detector/RSSI mode.
Note 2: For detector mode, connect high impedance volt meter to the OUTP / OUTN port.
Note 3: For controller mode, remove R9 & C3 and install 1k Ω resistor (R7, not included) and 100pF capacitor (C2, not included),
then make appropriate connection to OUTP and VSET. In controller mode, the OUTP / OUTN output can be used to drive
a variable gain amplier, or a variable attenuator, either directly or through a buffer or microcontroller. VSET should be
connected to an external supply, typically between +0.2 and +1.2V.
Note 4: An external capacitance C1 can be connected to CLPF port for additional ltering of OUTP and OUTN outputs..
HMC713LP3E
v01.1009 54 dB, LOGARITHMIC
DETECTOR / CONTROLLER, 50 - 8000 MHz
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
For price, delivery, and to place orders: Analog Devices, Inc.,
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
Phone: 781-329-4700 • Order online at www.analog.com
Application Support: Phone: 1-800-ANALOG-D
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
POWER DETECTORS - SMT
11
11 - 11
Item Description
J1 - J4 PC Mount SMA Connector
J5 - J7 DC Pin
C3 1 pF Capacitor, 0402 Pkg.
C6 0.1 µF Capacitor, 0402 Pkg.
C7, C8 100 pF Capacitor, 0402 Pkg.
R2 14 Resistor, 0402 Pkg.
R3 68 Resistor, 0402 Pkg.
R4 22 Resistor, 0402 Pkg.
R6, R8 10k Resistor, 0402 Pkg.
R9 1k Resistor, 0402 Pkg.
R10, R11 0 Resistor, 0402 Pkg.
U1 HMC713LP3E Logarithmic Amplier
PCB [2] 125823 Evaluation PCB
[1] Reference this number when ordering complete evaluation PCB
[2] Circuit Board Material: Arlon 25FR or Rogers 4350
Evaluation PCB
The circuit board used in the nal application
should use RF circuit design techniques. Signal
lines should have 50 ohm impedance while the
package ground leads and exposed paddle should
be connected directly to the ground plane similar
to that shown. A sufficient number of via holes
should be used to connect the top and bottom
ground planes. The evaluation circuit board shown
is available from Hittite upon request.
List of Materials for Evaluation PCB 125825 [1]
HMC713LP3E
v01.1009 54 dB, LOGARITHMIC
DETECTOR / CONTROLLER, 50 - 8000 MHz
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
For price, delivery, and to place orders: Analog Devices, Inc.,
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
Phone: 781-329-4700 • Order online at www.analog.com
Application Support: Phone: 1-800-ANALOG-D
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
POWER DETECTORS - SMT
11
11 - 12
Notes:
HMC713LP3E
v01.1009 54 dB, LOGARITHMIC
DETECTOR / CONTROLLER, 50 - 8000 MHz
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
For price, delivery, and to place orders: Analog Devices, Inc.,
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
Phone: 781-329-4700 • Order online at www.analog.com
Application Support: Phone: 1-800-ANALOG-D