KAOHSIUNG HITACHI ELECTRONICS CO.,LTD P.O. BOX 26-27 2,13TH EAST ST. K.E.P.Z. KAOHSIUNG TAIWAN R.O.C. TEL:(07) 821-5811(7 LINE) FAX:(07) 821-5815 FOR MESSRS : DATE : Nov.12,2010 CUSTOMER'S ACCEPTANCE SPECIFICATIONS TX14D11VM1CAB CONTENTS No. ITEM SHEET No. PAGE 1 COVER 7B64PS 2701-TX14D11VM1CAB-4 1-1/1 2 RECORD OF REVISION 7B64PS 2702-TX14D11VM1CAB-4 2-1/2~2/2 3 GENERAL DATA 7B64PS 2703-TX14D11VM1CAB-4 3-1/1 4 ABSOLUTE MAXIMUM RATINGS 7B64PS 2704-TX14D11VM1CAB-4 4-1/1 5 ELECTRICAL CHARACTERISTICS 7B64PS 2705-TX14D11VM1CAB-4 5-1/3~3/3 6 OPTICAL CHARACTERISTICS 7B64PS 2706-TX14D11VM1CAB-4 6-1/3~3/3 7 BLOCK DIAGRAM 7B64PS 2707-TX14D11VM1CAB-4 7-1/1 8 INTERFACE TIMING CHART 7B64PS 2708-TX14D11VM1CAB-4 8-1/5~5/5 9 DIMENSIONAL OUTLINE 7B63PS 2709-TX14D11VM1CAB-4 9-1/2~9-2/2 10 APPEARANCE STANDARD 7B64PS 2710-TX14D11VM1CAB-4 10-1/5~5/5 11 PRECAUTION IN DESIGN 7B64PS 2711-TX14D11VM1CAB-4 11-1/3~3/3 12 DESIGNATION OF LOT MARK 7B64PS 2712-TX14D11VM1CAB-4 12-1/1 13 PRECAUTION FOR USE 7B64PS 2713-TX14D11VM1CAB-4 13-1/1 *When product will be discontinued, customer will be informed by HITACHI with twelve months prior to discontinuation. ACCEPTED BY; KAOHSIUNG HITACHI ELECTRONICS CO.,LTD. PROPOSED BY; Sh. No. 7B64PS 2701-TX14D11VM1CAB-4 PAGE 1-1/1 RECORD OF REVISION DATE SHEET No. Jun.02,'06 7B64PS 2704TX14D11VM1CAB-2 PAGE 4-2/2 May.13,'08 7B64PS 2705TX14D11VM1CAB-3 PAGE 5-1/3 SUMMARY 4.2 ENVIRONMENTAL ABSOLUTE MAXIMUM RATINGS Delete : Note 13 : Operation Temperature of Touch Panel is -5 ~ 60 None - operation Temperature of Touch Panel is -20 ~ 70 5.2.3 MECHANICAL CHARACTERISTICS Changed: ITEM SPECIFICATION NOTE Pen Input Pressure 0.1~0.8N R0.8, Polyacetal Pen Finger 0.1~1.0N R8, Silicon Rubber ITEM SPECIFICATION NOTE Pen Input Pressure 1.2N max. R0.8, Polyacetal Pen Finger 1.2N max. R8, Silicon Rubber 7B64PS 2708TX14D11VM1CAB-3 PAGE 8-5/5 8.5 INTERNAL PIN CONNECTION Changed : CN1 JAE : FA5B040HF1(Sn plating) FA5B040HP1R3000(Au plating) 7B64PS 2709TX14D11VM1CAB-3 PAGE 9-2/2 7B64PS 2712TX14D11VM1CAB-3 PAGE 12-1/1 9. DIMENSIONAL OUTLINE The lot label size and position is changed. 12.1 LOT MARK Changed : 5 digits for production number 6 digits for production number 12.3 LOCATION OF LOT MARK Changed : 12.4 REVISION(Rev.) CONTROL Added : Rev. B CN1 JAE : FA5B040HP1R3000 Sh. KAOHSIUNG HITACHI 7B64PS 2702-TX14D11VM1CAB-4 PAGE 2-1/2 DATE Nov.12,'10 No. ELECTRONICS CO.,LTD. RECORD OF REVISION DATE Nov.12,'10 SHEET No. 7B64PS 2710TX14D11VM1CAB-4 PAGE 10-5/5 SUMMARY 10.3 APPEARANCE SPECIFICATION Changed : Blistering Puffiness 0.4mm max. 0.6mm max. Sh. KAOHSIUNG HITACHI 7B64PS 2702-TX14D11VM1CAB-4 PAGE 2-2/2 DATE Nov.12,'10 No. ELECTRONICS CO.,LTD. 3.GENERAL DATA (1) Part Name TX14D11VM1CAB (2) Module Dimensions 167.0(W)mm x 109.0(H)mm x (10.9)(D)mm max. (3) LCD Active Area 115.2(W)mm x 86.4(H)mm (4) Dot Pitch 0.12(W)mm x 3(R,G,B)(W) x 0.36(H)mm (5) Resolution 320x3(R,G,B)(W)x240(H) dots (6) Color Pixel Arrangement R,G,B Vertical stripe (7) LCD Type Transmissive Color TFT LCD (Normally White) (8) Display Type Active Matrix (9) Number of Colors 262k Colors (R,G,B 6bit parallel) (10) Backlight Cold Cathode Fluorescent Tube (U type CFL) x 1 (11) Weight (220)g (12) Interface 40pin (C-MOS) (13) Power Supply Voltage 3.3V only (Include Timing Controller and Power Unit) (14) View Direction 6 O'clock (15) Touch Panel Resistance type The surface is antiglare type Sh. KAOHSIUNG HITACHI 7B64PS 2703-TX14D11VM1CAB-4 PAGE 3-1/1 DATE Nov.12,'10 No. ELECTRONICS CO.,LTD. 4. ABSOLUTE MAXIMUM RATINGS 4.1 ELECTRICAL ABSOLUTE MAXIMUM RATINGS OF LCD ITEM SYMBOL MIN. MAX. Power Supply for Logic VDD -0.3 4.0 Input Voltage VI -0.2 VDD+0.2 Input Current Ii 0 1 VESD0 100 Static Electricity VESD1 8 Note 1 : DTMG,DCLK,RD0~RD5,GD0~GD5,BD0~BD5. Note 2 : 200pF-250 25 - 70%RH Note 3 : Interface Pin Connector. Note 4 : The surface of metal bezel and LCD panel . 4.2 ENVIRONMENTAL ABSOLUTE MAXIMUM RATINGS OPERATING STORAGE I T E M MIN. MAX. MIN. MAX. Temperature (-20) (70) (-30) (80) Humidity (Note 1) (Note 1) 19.6m/s2 4.9m/s2 Vibration (2G) (0.5G) (Note 5) 490m/s2 29.4m/s2 Shock (50G) (3G) (Note 5) Corrosive Gas Not Acceptable Not Acceptable 50,000 h CFL Life Time (Average) (Note 11) VSS=0V UNIT COMMENT V (Note 1) A V (Note 2,3) kV (Note 2,4) COMMENT (Note 2,3,6,7,8,10,12,13) Without condensation (Note 4) XYZ directions (Note 9) at 25 , IL=4.0mA max. Note 1 : Ta40 : 85%RH max. Ta40 : Absolute humidity must be lower than the humidity of 85%RH at 40. Note 2 : For storage condition Ta at -30 48h , at 80 100h. For operating condition Ta at -20 100h Note 3 : Background color changes slightly depending on ambient temperature. This phenomenon is reversible. Note 4 : 5Hz~100Hz(Except resonance frequency) Note 5 : This LCM will resume normal operation after finishing the test. Note 6 : The response time will be slower at low temperature. Note 7 : Only operation is guarantied at operating temperature. Contrast, response time, another display quality are evaluated at +25. Note 8 : When LCM is operated over 60 ambient temperature , the ICFL of LCM should be adjusted to 3mA max. Note 9 : Pulse Width : 10ms Note 10 : This is panel surface temperature , not ambient temperature. Note 11 : When brightness reached 50% of initial brightness. Note 12 : When LCM be operated less than 0 , the life time of CFL will be reduced . The rise time of CFL ON will be longer when the ambient temperature below 0 and confirming the characteristics of inverter is necessary . Sh. KAOHSIUNG HITACHI 7B64PS 2704-TX14D11VM1CAB-4 PAGE 4-1/1 DATE Nov.12,'10 No. ELECTRONICS CO.,LTD. 5. ELECTRICAL CHARACTERISTICS 5.1 ELECTRICAL CHARACTERISTICS OF LCD I T E M Power Supply Voltage Input Voltage for Logic (Note 1) Power Supply Current (Note 2) Vsync Frequency Hsync Frequency DCLK Frequency SYMBOL VDD Ta=25,VSS=0V CONDITION "H" level "L" level MIN. 3.0 2.0 VSS TYP. 3.3 - MAX. 3.6 VDD 0.8 UNIT V IDD VDD-VSS=3.3V - (150) - mA fV fH fCLK - 52 13.1 4.85 60 15.2 5.85 68 17.7 (7.0) Hz kHz MHz VI V Note 1 : DTMG,DCLK, RD0~RD5,GD0~GD5,BD0~BD5. Note 2 : f V=60Hz,Ta=25, Pattern used as display pattern : All Black. Note 3 : Need to make sure of flickering and rippling of display when setting the frame frequency in your set. 5.2 ELECTRICAL CHARACTERISTICS OF TOUCH PANEL 5.2.1 OPERATING CONDITION ITEM SPECIFICATION Operating Voltage 5VDC max. 5.2.2 ELECTRICAL CHARACTERISTICS ITEM SPECIFICATION Resistance XR-XL 210~640 Between Terminal YT-YB 240~680 Insulation Resistance X-Y 20Mmin. X 1.5% max. Linearity Y 1.5% max. Chattering 10ms max. 5.2.3 MECHANICAL CHARACTERISTICS ITEM SPECIFICATION Pen Input Pressure 1.2N max. Finger 1.2N max. Surface Hardness 2H min. 5.2.4 OPTICAL CHARASTERISTICS ITEM Transparency SPECIFICATION 76% min NOTE Operating Voltage : 25V DC (Note 1) NOTE R0.8, Polyacetal Pen R8, Silicon Rubber NOTE Sh. KAOHSIUNG HITACHI 7B64PS 2705-TX14D11VM1CAB-4 PAGE 5-1/3 DATE Nov.12,'10 No. ELECTRONICS CO.,LTD. 5.3 ELECTRICAL CHARACTERISTICS OF BACKLIGHT ITEM SYMBOL MIN. TYP. Lamp Voltage VL 760 Frequency fL 55 Lamp Current (1Lamp)(Note 6) IL 3.0 4.0 VS Starting Discharge Voltage 1300 (Note 2) MAX. 6.0 UNIT Vrms kHz mA NOTE Ta=25 Ta=25 - Vrms Ta=5 Note 1 : Please design your lamp driving circuit (inverter) according to the above specifications, and inform HITACHI about it. Note 2 : Starting discharge voltage is increased when LCM is operating under low temperature. Please check the characteristics of your inverter before applying to your set. Note 3 : Average life time of CFL will be decreased when LCM is operating under low temperature. Note 4 : Under lower driving frequency of an inverter, a certain Backlight system (CFL & CFL reflection sheet) may generate a sound noise. Before designing the inverter, please consider the driving frequency and noise. Note 5 : When IL is over 6.0mA, it may cause uneven contrast near CFL location, due to heat dispersion from CFL. Note 6 : We recommend to equip protection circuit (To stop output) which works under abnormal operation to the inverter for CFL Sh. KAOHSIUNG HITACHI 7B64PS 2705-TX14D11VM1CAB-4 PAGE 5-3/3 DATE Nov.12,'10 No. ELECTRONICS CO.,LTD. 6. OPTICAL CHARACTERISTICS 6.1 OPTICAL CHARACTERISTICS OF LCD ITEM Viewing Area Contrast Ratio Response Time (rise+fall) Red Green SYMBOL CONDITION MIN. x =0,K5.0 - Blue White TYP. MAX. UNIT x' =180,K5.0 y =90,K5.0 y' =270,K5.0 - 50 K =0,=0 120 tr+tf =0,=0 1~5 65 deg 1~5 70 deg 1~5 - deg 1~5 350 - - 5 - (45) - ms 6 x 0.56 0.61 0.66 - y 0.28 0.33 0.38 - x 0.25 0.30 0.35 - 0.52 0.57 0.62 - x 0.09 0.14 0.19 - y 0.03 0.08 0.13 - x 0.24 0.29 0.34 - y 0.24 0.29 0.34 - =0, =0 65 - NOTE deg y Color Tone (Primary Color) Ta=25 (Backlight on) (Measurement condition : HITACHI standard) (Note 3~6) : See next page. Note 1 : Driving Condition Display Pattern : White Raster ICFL Current : 4mA Note 2 : Measurement Condition (Transmitance) BM-5A or Similar equipment LCD panel Sh. KAOHSIUNG HITACHI 7B64PS 2706-TX14D11VM1CAB-4 PAGE 6-1/3 DATE Nov.12,'10 No. ELECTRONICS CO.,LTD. 6.2 OPTICAL CHARACTERISTICS OF BACKLIGHT ITEM MIN. TYP. MAX. UNIT Brightness (480) cd/m2 Rise Time - 3 Brightness Uniformity - - NOTE IL=4.0 mA (Note 1,2) IL=4.0 mA Minute Brightness 80% Under mentioned 25 % (Note 1,3) (Measurement condition : HITACHI standard) CFL:0h operation, Ta=25C Display data should all be "ON" Note 1 : Measurement after 10 minutes from CFL operating. Average value of 9 points (Note 3) Note 2 : Brightness control : 100%. Note 3 : Measurement of the following 9 places on the display. Y=180 Y=480 Y=780 P1 P4 P7 P2 P5 P8 P3 P6 P9 X=70 X=120 X=170 Note 4 : Definition of the brightness tolerance. Max. brightness or Min. brightness - Average brightness x100 Average brightness Sh. KAOHSIUNG HITACHI 7B64PS 2706-TX14D11VM1CAB-4 PAGE 6-3/3 DATE Nov.12,'10 No. ELECTRONICS CO.,LTD. 7.BLOCK DIAGRAM I/F(CN1) Power Supply Power Circuit Data / Clock G1 Gate Driver Timing Controller G2 TFT-LCD G240 Timing Signals D1 D2 D960 Source Driver CN2 GND VL Touch Panel Signals CFL Touch Panel Sh. KAOHSIUNG HITACHI 7B64PS 2707-TX14D11VM1CAB-4 PAGE 7-1/1 DATE Nov.12,'10 No. ELECTRONICS CO.,LTD. 8.INTERFACE TIMING 8.1 INTERFACE TIMING DCLK Hsync Vsync DTMG Data ITEM Cycle time Low level Width High level Width Rise time Fall time Duty Set up time Hold time Cycle Valid width Rise/Fall time Set up Hold Cycle Valid width Rise/Fall time Set up time Hold time Rise/Fall time Horizontal back porch Horizontal front porch Vertical back porch Vertical front porch Set up time Hold time Rise/Fall time MIN. (142) 12 12 0.45 5 10 370 4 0 2 251 2 5 10 28 22 6 5 5 10 - TYP. (171) 0.5 MAX. (206) 25 25 0.55 (385) (5) (253) (2) (35) (30) (7) (6) - 397 30 261 50 30 25 UNIT SYMBOL REMARKS tCLK tWCL ns tWCH trCLK tfCLK D D= tCLKL/ CLK tSH ns for DCLK tHH tHP tCLK tWH ns tHr,tHf tSV tCLK for Hsync tHV tVP tHP tWV ns tVr,tVf tSI ns for DCLK tHI ns tIr,tIf tHBP tCLK tHFP tVBP tHP tVFP tSD ns for DCLK tHD ns tDr,tDf Note : Vsync Cycle No. should be set to odd. Sh. KAOHSIUNG HITACHI 7B64PS 2708-TX14D11VM1CAB-4 PAGE 8-1/5 DATE Nov.12,'10 No. ELECTRONICS CO.,LTD. 8.2 Timing Chart (Data is latched negative edge trigger of DCLK) tHf,tVf tIf,tDf tHr,tVr tIr,tDr VSYNCHSYNCDTMG R05G05B05 tWCH tCLK tfCLK trCLK 1.5V DCLK tCLKL DATA tWCL VIHmi n. VILma x. tHD tSD tHI tSI Invalid Data Invalid Data DTMG DCLK tHH tSH Hsync tSV tHV Vsync tHP Hsync tWH tHBP tHFP DTMG tVP Vsync tWV tVBP tVFP DTMG Note 1 : DTMG is definition of the above timing for Hsync and Vsync. Note 2 : No matter when Hsync and Vsync is inputted ,this LCM can be driven only DTMG Signal. DTMG should be set to low level when it is not input valid data. Sh. KAOHSIUNG HITACHI 7B64PS 2708-TX14D11VM1CAB-4 PAGE 8-2/5 DATE Nov.12,'10 No. ELECTRONICS CO.,LTD. 8.3 POWER ON/OFF SEQUENCE ON 3.0V 3.0V Power supply for Logic VDD(t ) OFF 0.8 V Input Voltage (Signal) VI(t ) 2.0 V 0.8V t1 t2 t3 t5 t6 t7 t4 Backlight PO WER ON t1 15 ms 0 ms t2 45 ms 0. 1s t3 PO WER OFF 5 ms t4 0 ms t5 45 ms 0 ms t6 20 ms 0. 4s t7 Note 1 : 0VVI(t) VDD(t) VI(t) and VDD(t) is a surfeit of condition for power on/off. Note 2 : Input Voltage(Signal) should not be set high impedance when power on. Sh. KAOHSIUNG HITACHI 7B64PS 2708-TX14D11VM1CAB-4 PAGE 8-3/5 DATE Nov.12,'10 No. ELECTRONICS CO.,LTD. 8.4 RELATIONSHIP BETWEEN DISPLAYED COLOR AND INPUT DATA COLOR & GRAY SCALE Basic Color Red Green Blue Black Blue Green Cyan Red Magenta Yellow White Black Darker Brighter Red Black Darker Brighter Green Black Darker Brighter Blue GRAY SCALE LEVELS R0 0 0 0 0 1 1 1 1 GS0 0 GS1 1 GS2 0 GS61 1 GS62 0 GS63 1 GS0 0 GS1 0 GS2 0 GS61 0 GS62 0 GS63 0 GS0 0 GS1 0 GS2 0 GS61 0 GS62 0 GS63 0 DATA SIGNAL R1 0 0 0 0 1 1 1 1 0 1 1 0 1 1 0 0 0 0 0 0 0 0 0 0 0 0 R2 R3 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 R4 0 0 0 0 1 1 1 1 0 0 0 R5 0 0 0 0 1 1 1 1 0 0 0 G0 0 0 1 1 0 0 1 1 0 0 0 G1 0 0 1 1 0 0 1 1 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 0 0 0 0 1 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0 0 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 G2 G3 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 G4 0 0 1 1 0 0 1 1 0 0 0 G5 0 0 1 1 0 0 1 1 0 0 0 B0 0 1 0 1 0 1 0 1 0 0 0 B1 0 1 0 1 0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 0 0 0 0 1 0 0 0 0 0 0 1 0 0 0 0 0 0 1 0 1 0 1 1 B2 B3 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 B4 0 1 0 1 0 1 0 1 0 0 0 B5 0 1 0 1 0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 Sh. KAOHSIUNG HITACHI 7B64PS 2708-TX14D11VM1CAB-4 PAGE 8-4/5 DATE Nov.12,'10 No. ELECTRONICS CO.,LTD. 8.5 INTERNAL PIN CONNECTION CN1 JAE : FA5B040HP1R3000(Au plating) (Suitable FPC : t0.30.03mm0.50.03mm pitch) PIN No. SIGNAL FUNCTION 1 VDD Power Supply for Logic 2 VDD Power Supply for Logic 3 VDD Power Supply for Logic 4 VDD Power Supply for Logic 5 NC No Connection 6 DTMG Timing Signal for Data 7 VSS GND 8 DCLK Dot Clock 9 VSS GND 10 NC No Connection 11 VSS GND 12 B5 Blue Data 13 B4 14 B3 15 VSS GND 16 B2 Blue Data 17 B1 18 B0 19 VSS GND 20 G5 Green Data 21 G4 22 G3 23 VSS GND 24 G2 Green Data 25 G1 26 G0 27 VSS GND 28 R5 Red Data 29 R4 30 R3 31 VSS GND 32 R2 Red Data 33 R1 34 R0 35 (IC) No Connection 36 VSS GND 37 NC No Connection 38 NC No Connection 39 NC No Connection 40 NC No Connection CN2 JST Housing : BHR-03VS-1 PIN SIGNAL LEVEL No. 1 VCFL 2 NC 3 VSS - FUNCTION Power Supply for CFL No connection GND for CFL Sh. KAOHSIUNG HITACHI 7B64PS 2708-TX14D11VM1CAB-4 PAGE 8-5/5 DATE Nov.12,'10 No. ELECTRONICS CO.,LTD. 10. APPEARANCE STANDARD 10.1 APPEARANCE INSPECTION CONDITION Visual inspection should be done under the following condition. (1) The (2) The (3) The The inspection should be done in a dark room.(More than 1000(lx) and non-directive) distance between eyes of an inspector and the LCD module is 30cm. viewing zone is shown the figure. is defined as 45 for LCM power off 5 for LCM power on eye eye LCD Bezel 10.2 DEFINITION OF ZONE Display area (pixel area) Until 1mm outside around display area A zone Metal bezel area (include I/F connector) B zone C zone Sh. KAOHSIUNG HITACHI 7B64PS 2710-TX14D11VM1CAB-4 PAGE 10-1/5 DATE Nov.12,'10 No. ELECTRONICS CO.,LTD. 10.3 APPEARANCE SPECIFICATION (1)LCD Appearance *) If the problem related to this section occurs about this item , the responsible persons of both party (Customer and HITACHI) will discuss the matter in detail. No. ITEM Scratches Dent Wrinkles in Polarizer Bubbles Stains Foreign Materials L Dark Spot C D Color Tone Color Uniformity Dot Defect APPLIED ZONE CRITERIA Length L(mm) Width W(mm) Maximum number acceptable Ignored 10 10 Minimum space W0.02 Ignored L40 0.02W0.04 L20 W0.04 Distinguished one is acceptable (To be judged by HITACHI standard) Same as above Average diameter Maximum number D(mm) acceptable D0.2 Ignored 0.2D0.3 12 0.3D0.5 3 0.5D none Filamentous (Line shape) Length Width Maximum number L(mm) W(mm) acceptable L2.0 W0.03 Ignored L3.0 0.03W0.05 6 L2.5 0.05W0.1 1 Round(Dot shape) Average diameter Maximum number Minimum Space D(mm) acceptable D0.2 Ignored 0.2D0.3 10 10 mm 0.3D0.4 5 30 mm 0.4D none The total number Filamentous + Round=10 Those wiped out easily are acceptable To be judged by HITACHI STANDARD Same as above Maximum number acceptable Sparkle mode 1 dot 4 2 dots 1 Total (Note.(3)-(f)) 5 Black mode 1 dot 5 2 dots 2 Total (Note.(3)-(f)) 5 Total (Note.(3)-(f)) 10 A,B A A A A,B A,B A A A Sh. KAOHSIUNG HITACHI 7B64PS 2710-TX14D11VM1CAB-4 PAGE 10-2/5 DATE Nov.12,'10 No. ELECTRONICS CO.,LTD. (2) CFL BACKLIGHT APPEARANCE No. ITEM Dark Spots C White Spots F Foreign Materials L (Spot) Foreign Materials B (Line) A C K L Scratches I G H T APPLIED ZONE CRITERIA Average diameter D(mm) D0.4 0.4D Width W(mm) W0.2 0.2<W Width W(mm) W0.1 0.1W0.2 0.2W Maximum number acceptable Length L(mm) L2.5 2.5L Length L(mm) L11.0 11.0L - ignored none Maximum number acceptable 1 None none Maximum number acceptable ignored 1 None none A A A Sh. KAOHSIUNG HITACHI 7B64PS 2710-TX14D11VM1CAB-4 PAGE 10-3/5 DATE Nov.12,'10 No. ELECTRONICS CO.,LTD. (3)Touch panel appearance Visual inspection should be done under the following condition. *) The inspection should be done in a dark room. (more than 500 (lx) and non-directive) *) The distance between eyes of an inspector and the LCD module is 30 cm. *) The viewing angle60. No. ITEM Scratches T O U C H Width W(mm) W0.1 0.10W0.05 0.05W Length Maximum number L(mm) acceptable None L10 4 pcs max. L10 Ignored L10 Filamentous (Line shape) Width Length Maximum number W(mm) L(mm) acceptable Dust (circular) W0.10 None 0.10W0.05 3L Ignored 0.05W L3 Round(Dot shape) Average diameter Maximum number D(mm) acceptable None D0.35 6 psc max. 0.35D0.25 Ignored D0.25 Foreign Materials Dark Spot P A N E L Newton Ring (Touch Panel) Touch Panel Uncleanliness Rubbing Scratch Need to discuss with customer A,B A,B A,B B A,B A,B No conspicuous dirt A To be judged by HITACHI standard - (4) Glass indentation ITEM SPECIFICATIONS X Common Indentation Y X Y Z 5.0 3.0 1.1 Z Corner Broken APPLIED ZONE CRITERIA Y Z X X 3 Y 3 Z 1.1 Proceeding Crack None Other Y Y1 Sh. KAOHSIUNG HITACHI 7B64PS 2710-TX14D11VM1CAB-4 PAGE 10-4/5 DATE Nov.12,'10 No. ELECTRONICS CO.,LTD. Blistering Puffiness Gauge 0.6 mm max. Touch Panel Note 1 : Definition of average diameter (D) b D= a+b 2 a Note 2 : Definition of length (L) and width (W) W L Note 3 : Definition of dot defect (a) Dot Defect : Defect Area 1/2 dot (b) Sparkle mode : Brightness of dot is more than 30% at Black raster. (c) Black mode : Brightness of dot is less than 70% at R.G.B raster. (d) 1 dot : Defect dot is isolated , not attached to other defect dot. (e) N dot : N defect dots are consecutive (fig.1). (N means the number of defect dots.) ( fig .1) R G B R G B R G B x 2 dots defect included defect dot "X" is defined as follows. Adjacent dots to defect dot "X" : (f) Counting definition of adjacent dots (1 set) : same as 1 dot defect. (g) Those wiped out easily are acceptable. Sh. KAOHSIUNG HITACHI 7B64PS 2710-TX14D11VM1CAB-4 PAGE 10-5/5 DATE Nov.12,'10 No. ELECTRONICS CO.,LTD. 11. PRECAUTION IN DESIGN 11.1 MOUNTING PRECAUTION Please mount the LCD Module by using mounting holes provided. While mounting please pay attention to the followings. Touch panel The module Space Spacer Customer's housing Protective spacer Example of mounting 152.0 0.3 (T.B.D) (T.B.D) (T.B.D) (T.B.D) 101.0 0.3 (T.B.D Upper panel Protective spacer 4- 5.0 (T.B.D) (T.B.D) Lower panel Spacer 4- 7.0 Unit : mm Scale: NTS Location of spacers (1) To prevent the module cover from being pressed, the distance between the module and the fitting plate, which means the length of the spacers, should be shorter than 1.0mm. (2) The use of protective spacers are recommend in order to protect the module from shock. (3) For the module to be used at upright position, the case shall have a structure where the touch panel screen does not shift with its own weight. 11.2 PRECAUTIONS AGAINST ELECTROSTATIC DISCHARGE As this module contains C-MOS LSIs, it is not strong against electrostatic discharge. Make certain that the operator's body is connected to the ground through a list band , etc. And don't touch I/F pins directly. Sh. KAOHSIUNG HITACHI 7B64PS 2711-TX14D11VM1CAB-4 PAGE 11-1/3 DATE Nov.12,'10 No. ELECTRONICS CO.,LTD. 11.3 HANDLING PRECAUTIONS (1) Since the Touch Panel on the top, and the frame on the bottom tend to be easily damaged, they should be with full care so as not to get them touched, pushed or rubbed by a piece on glass, tweezers and anything else which are harder a pencil lead 2H. (2) As the adhesives used for adhering upper/lower polarizer's and frame are made of organic substances which will be deteriorated by a chemical reaction with such chemicals as acetone, toluene, ethanol and isopropyl alcohol. The following are recommended for use : normal hexane Please contact with us when it is necessary for you to use chemicals other than the above. (3) Lightly wipe to clean the dirty surface with absorbent cotton or other soft material like chamois, soaked in the recommended chemicals without scrubbing it hardly. Always wipe the surface horizontally or vertically. Never give a wipe in a circle. To prevent the display surface from damage and keep the appearance in good state, it is sufficient, in general, to wipe it with absorbent cotton. (4) Immediately wipe off saliva or water drop attached on the display area because it may cause deformation or faded color. (5) Fogy dew deposited on the surface may cause a damage, stain or dirt to the polarizer. When you need to take out the LCD module from some place at low temperature for test, etc. It is required to be warmed them up to temperature higher than room temperature before taking them out. (6) Touching the display area or I/F pins with bare hands or contaminating them are prohibited, because the stain on the display area and poor insulation between terminals are often caused by being touched with bare hands. (Some cosmetics are detrimental to polarizer's.) (7) In general, the glass is fragile so that, especially on its periphery, tends to be cracked or chipped in handling. Please do not give the LCD module sharp shocks by falling, etc. (8) Maximum pressure to the surface must be less than 1.96x104 Pa. And if the pressure area is less than 1cm2 , maximum pressure must be less than 1.96N. (9) Since the metal width is narrow on these locations (see page 9-1/2), please careful with handling. (10) Top sheets shall be cleaned gently using a soft cloth such as those used for glasses. Hard wiping accumulated dust will leave scars on the surface even using a cloth. Sh. KAOHSIUNG HITACHI 7B64PS 2711-TX14D11VM1CAB-4 PAGE 11-2/3 DATE Nov.12,'10 No. ELECTRONICS CO.,LTD. 11.4 OPERATION PRECAUTION (1) Using a LCM module beyond its maximum ratings may result in its permanent destruction. LCM module's should usually be used under recommended operating conditions shown in chapter 4. Exceeding any of these conditions may adversely affect its reliability. (2) Response time will be extremely delayed at lower temperature than the specified operating temperature range and on the other hand LCD's shows dark blue at higher temperature. However those phenomena do not main defects of the LCD module. Those phenomena will disappear in the specified operating temperature range. (3) If the display area is pushed hard during operation, some display patterns will be abnormally display. (4) A slight dew depositing on terminals may cause electrochemical reaction which leads to terminal open circuit. Please operate the LCD module under the relative condition of 40 85%RH. (5) Resistance range : Your controller shall be set up to allow the resistance range of Touch Panel specified in our CAS. (6) Pointed position of Touch Panel may shift owing to a change in resistance of Touch Panel depending on the operation condition . To compensate this shift, the set shall be given a calibration function. (7) Input shall be made with a stylus pen (poly acetal , R0.8). Chances are very high that use of a metal piece including a ball point pen or sharp edge will impair accuracy. (8) The Touch Panel is an auxiliary input device. The system shall be designed to have other input device. 11.5 STORAGE In case of storing LCD module for a long period of time (for instance, for years) for the purpose of replacement use, the following precautions necessary. (1) Store the LCD modules in a dark place; do not expose them to sunlight or ultraviolet rays. (2) Keep the temperature between 10 and 35 at normal humidity. (3) Store the LCD modules in the container which is used for shipping from us. (4) No articles shall be left on the surface over an extended period of time. 11.6 SAFETY Wear finger cots or gloves whenever handling or assembling a Touch Panel its glass edges are sharp. Sh. KAOHSIUNG HITACHI 7B64PS 2711-TX14D11VM1CAB-4 PAGE 11-3/3 DATE Nov.12,'10 No. ELECTRONICS CO.,LTD. 12. DESIGNATION OF LOT MARK 12.1 LOT MARK Lot mark is consisted of 5 digits for production lot and 6 digits for production control. 8 0 4 1 Year Figure in lot mark 2010 0 2011 1 2012 2 Week 2013 3 Month 2014 4 T Digits for production control T : Made in Taiwan Year Month Figure in lot mark Month Figure in lot mark Week (day in calendar) Figure in lot mark Jan. 01 Jul. 07 1~ 7 1 Feb. 02 Aug. 08 8~14 2 Mar. 03 Sep. 09 15~21 3 Apr. 04 Oct. 10 22~28 4 May 05 Nov. 11 29~31 5 Jun. 06 Dec. 12 12.2 SERIAL No. Serial No. is consisted of 6 digits number (000001~999999). 12.3 LOCATION OF LOT MARK Label is bring attached on the back side of module. 12.4 REVISION(Rev.) CONTROL Rev No. A B ITEM CN1 JAE : FA5B040HF1 CN1 JAE : FA5B040HP1R3000 Sh. KAOHSIUNG HITACHI 7B64PS 2712-TX14D11VM1CAB-4 PAGE 12-1/1 DATE Nov.12,'10 No. ELECTRONICS CO.,LTD. 13. PRECAUTION FOR USE (1) A limit sample should be provided by the both parities on an occasion when the both parties agree to its necessity. Judgment by a limit sample shall take effect after the limit sample has been established and confirmed by the both parties. (2) On the following occasions, the handling of the problem should be decided through discussion and agreement between responsible persons of the both parties. (1) When a question is arisen in the specifications. (2) When a new problem is arisen which is not specified in this specifications. (3) When an inspection specifications change or operating condition change by customer is reported to HITACHI, and some problem is arisen in the specification due to the change. (4) When a new problem is arisen at the customer's operating set for sample evaluation. (3) Regarding the treatment for maintenance and repairing, both parties will discuss it in six months later after latest delivery of this product. The precaution that should be observed when handling LCM have been explained above. If any points are unclear or if you have any requests , please contact with HITACHI. Sh. KAOHSIUNG HITACHI 7B64PS 2713-TX14D11VM1CAB-4 PAGE 13-1/1 DATE Nov.12,'10 No. ELECTRONICS CO.,LTD.