2SJ668(TE16L1,NQ) - TOSHIBA

2SJ668

2010-02-05

TOSHIBA Field Effect Transistor Silicon P-Channel MOS Type (U−MOSIII)

2SJ668

Relay Drive, DC/DC Converter and Motor Drive

Applications

z 4 V gate drive

z Low drain-source ON-resistance: RDS (ON) = 0.12 Ω (typ.)

z High forward transfer admittance: |Yfs| = 5.0 S (typ.)

z Low leakage current: IDSS = −100 μA (max) (VDS = −60 V)

z Enhancement mode: Vth = −0.8 to −2.0 V (VDS = −10 V, ID = −1 mA)

Absolute Maximum Ratings (Ta = 25°C)

Characteristic Symbol Rating Unit

Drain-source voltage VDSS −60 V

Drain-gate voltage (RGS = 20 kΩ) VDGR −60 V

Gate-source voltage VGSS ±20 V

DC (Note 1) ID −5 A

Drain current

Pulse (Note 1) IDP −20 A

Drain power dissipation (Tc=25°C) PD 20 W

Single pulse avalanche energy

(Note 2)

EAS 40.5 mJ

Avalanche current IAR −5 A

Repetitive avalanche energy (Note 3) EAR 2 mJ

Channel temperature Tch 150 °C

Storage temperature range Tstg −55 to 150 °C

Note: Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the significant change in

temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e.

operating temperature/current/voltage, etc.) are within the absolute maximum ratings. Please design the appropriate

reliability upon reviewing the Toshiba Semiconductor Reliability Handbook (“Handling Precautions”/“Derating Concept and

Methods”) and individual reliability data (i.e. reliability test report and estimated failure rate, etc).

Thermal Characteristics

Characteristic Symbol Max Unit

Thermal resistance, channel to case Rth (ch−c) 6.25 °C / W

Thermal resistance, channel to ambient Rth (ch−a) 125 °C / W

Note 1: Ensure that the channel temperature does not exceed 150°C.

Note 2: VDD = −25 V, Tch = 25°C (initial), L = 2.2 mH, RG = 25 Ω,

IAR = −5 A

Note 3: Repetitive rating: pulse width limited by maximum channel temperature

This transistor is an electrostatic-sensitive device. Handle with care.

Unit: mm

1.1 ± 0.2

0.1 ± 0.1

1.05 MAX.

2.3 ± 0.15

5.2 ± 0.2

0.8 MAX.

0.6 MAX.

9.5 ± 0.3

1.2 MAX.

1.5 ± 0.2

6.5 ± 0.2

1 2 3

0.6 MAX.

5.5 ± 0.2

0.6 ± 0.15

2.3 ± 0.2

2.3 ± 0.15

1. GATE

2. DRAIN

（HEAT SINK）

3. SOURSE

JEDEC ―

JEITA ―

TOSHIBA 2-7J1B

Weight: 0.35 g (typ.)

2SJ668

2010-02-05

Electrical Characteristics (Ta = 25°C)

Characteristic Symbol Test Condition Min Typ. Max Unit

Gate leakage current IGSS V

GS = ±16 V, VDS = 0 V — — ±10 μA

Drain cutoff current IDSS V

DS = −60 V, VGS = 0 V — — −100 μA

V (BR) DSS I

D = −10 mA, VGS = 0 V −60 — — V

Drain-source breakdown voltage

V (BR) DSX I

D = −10 mA, VGS = 20 V −35 — — V

Gate threshold voltage Vth V

DS = −10 V, ID = −1 mA −0.8 — −2.0 V

VGS = −4 V, ID = −2.5 A — 0.16 0.25

Drain-source ON-resistance RDS (ON)

VGS = −10 V, ID = −2.5 A — 0.12 0.17

Ω

Forward transfer admittance |Yfs| VDS = −10 V, ID = −2.5 A 2.5 5.0 — S

Input capacitance Ciss — 700 —

Reverse transfer capacitance Crss — 60 —

Output capacitance Coss

VDS = −10 V, VGS = 0 V, f = 1 MHz

— 90 —

Rise time tr — 14 —

Turn-on time ton — 24 —

Fall time tf — 14 —

Switching time

Turn-off time toff

— 95 —

Total gate charge (gate-source

plus gate-drain) Qg — 15 —

Gate-source charge Qgs — 11 —

Gate-drain (“Miller”) charge Qgd

VDD ≈ −48 V, VGS = −10 V, ID = −5 A

— 4 —

Source-Drain Ratings and Characteristics (Ta = 25°C)

Characteristic Symbol Test Condition Min Typ. Max Unit

Continuous drain reverse current

(Note 1)

IDR — — — −5 A

Pulse drain reverse current

(Note 1)

IDRP — — — −20 A

Forward voltage (diode) VDSF I

DR = −5 A, VGS = 0 V — — 1.7 V

Reverse recovery time trr — 40 — ns

Reverse recovery charge Qrr

IDR = −5 A, VGS = 0 V

dlDR / dt = 50 A/μs — 32 — nC

Marking

Duty ≤ 1%, tw = 10 μs

−10 V

0 V

VGS

RL = 12 Ω

VDD ≈ −30 V

ID = −2.5 A

Output

4.7 Ω

Note 4 : A line under a Lot No. identifies the indication of product Labels

[[G]]/RoHS COMPATIBLE or [[G]]/RoHS [[Pb]]

Please contact your TOSHIBA sales representative for details as to

environmental matters such as the RoHS compatibility of Product.

The RoHS is Directive 2002/95/EC of the European Parliament and

of the Council of 27 January 2003 on the restriction of the use of certain

hazardous substances in electrical and electronic equipment.

J668

Lot No.

Note 4

Part No.

(or abbreviation code)

2SJ668

2010-02-05

VDS – VGS

Drain-source voltage VDS (V)

Gate-source voltage VGS (V)

−2.0

−0.4

−1.2

−0.8

−1.6

−40 −20−8−12 −16

−

ID = −1.2 A

Common source

Tc= 25°C

Pulse test

ID – VDS

Drain current ID (A)

Drain-source voltage VDS (V)

−5

−1

−3

−2

−4

0 −0.4 −2.0−0.8 −1.2 −1.6

−10

−8

−6

−2.8

−3.5

−4.

VGS = −2.5V

Common source

Tc = 25°C

Pulse test

−3

ID – VGS

Drain current ID (A)

Gate-source voltage VGS (V)

−10

−2

−6

−8

−1 0 −5−3 −4

100

Tc = −55°C

Common source

VDS = −10 V

Pulse test

−4

−2

⎪Yfs⎪ − ID

Forward transfer admittance ⎪Yfs⎪ (S)

Drain current ID (A)

0.1

100

−0.1 −100−1

Common source

VDS = −10 V

Pulse test

Tc = −55°C

100

−10

ID – VDS

Drain current ID (A)

Drain-source voltage VDS (V)

−10

−2

−6

−4

−8

−20 −10−4−6 −8

−10

−8

−

−4

−3.5

−3

VGS = −2.5 V

Common source

Tc = 25°C

Pulse test

RDS (ON) − ID

Drain-source ON-resistance

RDS (ON) (Ω)

Drain current ID (A)

0.4

0.5

0 −2 −10

Common source

Tc = 25°C

Pulse test

−4

0.3

0.1

0.2

−6 −8

VGS = −10 V

−4 V

−2.5

2SJ668

2010-02-05

Vth − Tc

Gate threshold voltage Vth (V)

Case temperature Tc (°C)

−80 040 80 120 160−40

−2.0

−0.4

−1.2

−0.8

−1.6

Common source

VDS = −10 V

ID = 1 mA

Pulse test

Capacitance C (pF)

Capacitance – VDS

Drain-source voltage VDS (V)

100

1000

10000

−0.1 −1 −10 −100

Ciss

Coss

Crss

Common source

VGS = 0 V

f = 1 MHz

Tc = 25°C

RDS (ON) − Tc

Drain−source ON-resistance

RDS (ON) (Ω)

Case temperature Tc (°C)

0.4

0.1

0.3

0.2

−40 −80 1600 40 120 80

Common source

Pulse test

ID = −5 A

−2.5

−1.2

VGS = −10 V

VGS = −4 V

−

−2.5

−1.2

IDR − VDS

Drain reverse current IDR (A)

Drain-source voltage VDS (V)

0.1

0.201.2

0.6 0.4 0.8 1.0

Common source

Tc = 25°C

Pulse test

−10

−5

−3

−1 VGS = 0 V

Case temperature Tc (°C)

PD − Tc

Drain power dissipation PD (W)

0 80 20040 160 120

Total gate charge Qg (nC)

Drain-source voltage VDS (V)

Dynamic input/output

characteristics

Gate-source voltage VGS (V)

−50

−40

−30

−20

−10

0 25 30

10 5

−10

−5

−20

−25

−15

VGS

VDS

VDD = −48 V

−12V −24V

Common source

ID = −5 A

Ta = 25°C

Pulse test

20 15

2SJ668

2010-02-05

rth − tw

Pulse width tw (s)

Normalized transient thermal impedance

rth (t)/Rth (ch-c)

0.01

10 μ 100 μ 1 m 10 m 100 m 1 10

0.1

0.01

0.02

0.05

0.1

0.2

Duty = 0.5

Single Pulse

PDM

Duty = t/T

Rth (ch-c) = 6.25°C/W

Safe operating area

Drain-source voltage VDS (V)

Drain current ID (A)

ID max (continuous)

ID max (pulsed) *

DC operation

Tc = 25°C

1 ms * 100 μs *

*: Single nonrepetitive pulse

Tc = 25°C

Curves must be derated

linearly with increase in

temperature.

−0.1 −1 −10 −100

VDSS max

−1

−10

−100

−0.1

EAS – Tch

Channel temperature (initial) Tch (°C)

Avalanche energy EAS (mJ)

50 75 100 125 150

RG = 25 Ω

VDD = −25 V, L = 2.2 mH ⎟

⎟

⎠

⎞

⎜

⎝

⎛

−

⋅⋅⋅= VDD

BVDSS

ΕAS

Waveform

IAR

BVDSS

VDD V

Test circuit

−15 V

0 V

2SJ668

2010-02-05

RESTRICTIONS ON PRODUCT USE

• Toshiba Corporation, and its subsidiaries and affiliates (collectively “TOSHIBA”), reserve the right to make changes to the information

in this document, and related hardware, software and systems (collectively “Product”) without notice.

• This document and any information herein may not be reproduced without prior written permission from TOSHIBA. Even with

TOSHIBA’s written permission, reproduction is permissible only if reproduction is without alteration/omission.

• Though TOSHIBA works continually to improve Product’s quality and reliability, Product can malfunction or fail. Customers are

responsible for complying with safety standards and for providing adequate designs and safeguards for their hardware, software and

systems which minimize risk and avoid situations in which a malfunction or failure of Product could cause loss of human life, bodily

injury or damage to property, including data loss or corruption. Before customers use the Product, create designs including the

Product, or incorporate the Product into their own applications, customers must also refer to and comply with (a) the latest versions of

all relevant TOSHIBA information, including without limitation, this document, the specifications, the data sheets and application notes

for Product and the precautions and conditions set forth in the “TOSHIBA Semiconductor Reliability Handbook” and (b) the

instructions for the application with which the Product will be used with or for. Customers are solely responsible for all aspects of their

own product design or applications, including but not limited to (a) determining the appropriateness of the use of this Product in such

design or applications; (b) evaluating and determining the applicability of any information contained in this document, or in charts,

diagrams, programs, algorithms, sample application circuits, or any other referenced documents; and (c) validating all operating

parameters for such designs and applications. TOSHIBA ASSUMES NO LIABILITY FOR CUSTOMERS’ PRODUCT DESIGN OR

APPLICATIONS.

• Product is intended for use in general electronics applications (e.g., computers, personal equipment, office equipment, measuring

equipment, industrial robots and home electronics appliances) or for specific applications as expressly stated in this document.

Product is neither intended nor warranted for use in equipment or systems that require extraordinarily high levels of quality and/or

reliability and/or a malfunction or failure of which may cause loss of human life, bodily injury, serious property damage or serious

public impact (“Unintended Use”). Unintended Use includes, without limitation, equipment used in nuclear facilities, equipment used

in the aerospace industry, medical equipment, equipment used for automobiles, trains, ships and other transportation, traffic signaling

equipment, equipment used to control combustions or explosions, safety devices, elevators and escalators, devices related to electric

power, and equipment used in finance-related fields. Do not use Product for Unintended Use unless specifically permitted in this

document.

• Do not disassemble, analyze, reverse-engineer, alter, modify, translate or copy Product, whether in whole or in part.

• Product shall not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any

applicable laws or regulations.

• The information contained herein is presented only as guidance for Product use. No responsibility is assumed by TOSHIBA for any

infringement of patents or any other intellectual property rights of third parties that may result from the use of Product. No license to

any intellectual property right is granted by this document, whether express or implied, by estoppel or otherwise.

• ABSENT A WRITTEN SIGNED AGREEMENT, EXCEPT AS PROVIDED IN THE RELEVANT TERMS AND CONDITIONS OF SALE

FOR PRODUCT, AND TO THE MAXIMUM EXTENT ALLOWABLE BY LAW, TOSHIBA (1) ASSUMES NO LIABILITY

WHATSOEVER, INCLUDING WITHOUT LIMITATION, INDIRECT, CONSEQUENTIAL, SPECIAL, OR INCIDENTAL DAMAGES OR

LOSS, INCLUDING WITHOUT LIMITATION, LOSS OF PROFITS, LOSS OF OPPORTUNITIES, BUSINESS INTERRUPTION AND

LOSS OF DATA, AND (2) DISCLAIMS ANY AND ALL EXPRESS OR IMPLIED WARRANTIES AND CONDITIONS RELATED TO

SALE, USE OF PRODUCT, OR INFORMATION, INCLUDING WARRANTIES OR CONDITIONS OF MERCHANTABILITY, FITNESS

FOR A PARTICULAR PURPOSE, ACCURACY OF INFORMATION, OR NONINFRINGEMENT.

• Do not use or otherwise make available Product or related software or technology for any military purposes, including without

limitation, for the design, development, use, stockpiling or manufacturing of nuclear, chemical, or biological weapons or missile

technology products (mass destruction weapons). Product and related software and technology may be controlled under the

Japanese Foreign Exchange and Foreign Trade Law and the U.S. Export Administration Regulations. Export and re-export of Product

or related software or technology are strictly prohibited except in compliance with all applicable export laws and regulations.

• Please contact your TOSHIBA sales representative for details as to environmental matters such as the RoHS compatibility of Product.

Please use Product in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances,

including without limitation, the EU RoHS Directive. TOSHIBA assumes no liability for damages or losses occurring as a result of

noncompliance with applicable laws and regulations.