NX8563LB350-BA - California Eastern Laboratories / NEC

NEC's CW InGaAsP

MQW DFB LASER DIODE MODULE

FOR DWDM APPLICATIONS (10 mW MIN)

NX8563

SERIES

FEATURES

•OUTPUT POWER:

Pf = 10 mW MIN

•INTERNAL THERMOELECTRIC COOLER AND ISOLATOR

•HERMETICALLY SEALED 14-PIN BUTTERFLY PACKAGE

• POLARIZATION MAINTAIN FIBER PIGTAIL

• AVAILABLE FOR DWDM WAVELENGTHS BASED ON

ITU-T RECOMMENDATIONS (100 GHz GRID) REFER TO

THE ORDERING INFORMATION

NEC's NX8563 Series are a 1550 nm Multiple Quantum Well

(MQW) structured Distributed Feed-Back (DFB) laser diode

with Polarization Maintain Fiber (PMF). This device is de-

signed as Continuous Wave (CW) light source and ideal for

optical transmission systems in which external modulators are

used.

This device is available for Dense Wavelenght Division Multi-

plexing (DWDM) wave lengths based on ITU-T recommenda-

tions, enabling a wide range of applications.

DESCRIPTION

California Eastern Laboratories

Notes:

1. Available for DWDM based on ITU-T recommendations. Please refer to Ordering Information.

2. Polarization state of LD is aligned parallel to the slow axis.

PART NUMBER NX8563 Series

SYMBOLS PARAMETERS AND CONDITIONS UNITS MIN TYP MAX

TSET Laser Set Temperature °C20 35

VFForward Voltage, Pf = 10 mW V 1.2 1.5

IFForward Current, Pf = 10 mW mA 70 125

ITH Threshold Current mA 20 40

PfOptical Output Power from Fiber,

IF = 125 mA, TLD = TSET mW 10

λpPeak Emission Wavelength1, Pf = 10 mW, CW, nm 1527.99 ITU-T11611.78

TLD = TSET

∆v Spectral Line Width, Pf = 10 mW, CW, 3 dB down MHz 1 2

SMSR Side Mode Suppression Ratio, Pf = 10 mW, CW dB 33 45

RIN Relative Intensity Noise, Pf = 10 mW, 20 MHz to 3 GHz dB/Hz -150

ext Polarization Extinction Ratio2, Pf = 10 mW, CW dB 20

ELECTRO-OPTICAL CHARACTERISTICS (TLD = TSET, TC = -20 to +70°C)

ABSOLUTE MAXIMUM RATINGS1

(TC = 25°C, unless otherwise specified)

SYMBOLS PARAMETERS UNITS RATINGS

IFForward Current of LD mA 300

VRReverse Voltage of LD V 2.0

IFForward Current of PD mA 10

VRReverse Voltage of PD V 20

TCOperating Case Temperature °C -20 to +70

TSTG Storage Temperature °C -40 to +85

TSLD Lead Soldering °C 260

Temperature (10 s)

Note:

1. Operation in excess of any one of these parameters may result

in permanent damage.

PART NUMBER NX8563 Series

SYMBOLS PARAMETERS AND CONDITIONS UNITS MIN TYP MAX

ImMonitor Current, Pf = 10 mW, VR = 5 V µA 100 2000

IDDark Current, VR = 5 V nA 10

γ1Tracking Error, Im = const. dB 0.5

ELECTRO-OPTICAL CHARACTERISTICS (Applicable to Monitor PD: TLD = TSET, TC = -20 to +70°C)

(mW) TLD = TC = 25°C

(at Pf (25°C) = 10 mW)

TLD = 25°C, TC = -20 to +70°C

Note:

1. γ = 10 log Pf

10 mW

PART NUMBER NX8563 Series

SYMBOLS PARAMETERS AND CONDITIONS UNITS MIN TYP MAX

R Thermistor Resistance, TLD = 25°CkΩ9.5 10.0 10.5

B B Constant K 3350 3450 3550

ICCooler Current, ∆T = 70 - Tset, Pf = 10 mW A 1

VCCooler Voltage, ∆T = 70 - Tset, Pf = 10 mW V 2

ELECTRO-OPTICAL CHARACTERISTICS (Applicable to Thermistor and TEC: TLD = TSET, TC = -20 to +70°C)

NX8563 SERIES

TYPICAL PERFORMANCE CURVES (TC = TSET unless otherwise specified)

-10

-20

-30

-40

-50

-60

-70

1540 1550 1560

15.0

12.5

10.0

7.5

5.0

2.5

0 20 40 60 80 100

120

100

0 0.4 0.8 1.2 1.6 2.0 2.4

02550 75

LONGITUDINAL MODE

OPTICAL OUTPUT POWER FROM FIBER

vs. FORWARD CURRENT

FORWARD CURRENT vs.

FORWARD VOLTAGE

OPTICAL OUTPUT POWER FROM FIBER

vs. MONITOR CURRENT

THERMISTOR RESISTANCE vs.

AMBIENT TEMPERATURE

Wavelength λ (nm)

Relative Intensity (dB)

Forward Current, IF (mA)

Optical Output Power from Fiber, P

(mW)

Forward Voltage, VF (V)

Forward Current, I

(mA)

Optical Output Power from Fiber, P

(mW)

Monitor Current, IM (mA)

Ambient Temperature, TA (°C)

Thermistor Resistance, R (kΩ)

12.0

10.0

8.0

6.0

4.0

2.0

0 0.2 0.4 0.6 0.8 1.0

NX8563 SERIES

Wavelength code ITU-T1 Wavelength Frequency Wavelength code ITU-T1 Wavelength Frequency

(nm) (THz) (nm) (THz)

287 1528.77 196.10

295 1529.55 196.00

303 1530.33 195.90

311 1531.11 195.80

318 1531.89 195.70

326 1532.68 195.60

334 1533.46 195.50

342 1534.25 195.40

350 1535.03 195.30

358 1535.82 195.20

366 1536.60 195.10

373 1537.39 195.00

381 1538.18 194.90

389 1538.97 194.80

397 1539.76 194.70

405 1540.55 194.60

413 1541.34 194.50

421 1542.14 194.40

429 1542.93 194.30

437 1543.73 194.20

445 1544.52 194.10

453 1545.32 194.00

461 1546.11 193.90

469 1546.91 193.80

477 1547.71 193.70

485 1548.51 193.60

Note:

1. The Value which omitted and computed the 3rd place below the decimal point.

493 1549.31 193.50

501 1550.11 193.40

509 1550.91 193.30

517 1551.72 193.20

525 1552.52 193.10

533 1553.32 193.00

541 1554.13 192.90

549 1554.94 192.80

557 1555.74 192.70

565 1556.55 192.60

573 1557.36 192.50

581 1558.17 192.40

589 1558.98 192.30

597 1559.79 192.20

606 1560.60 192.10

614 1561.41 192.00

622 1562.23 191.90

630 1563.04 191.80

638 1563.86 191.70

646 1564.67 191.60

654 1565.49 191.50

663 1566.31 191.40

671 1567.13 191.30

679 1567.95 191.20

687 1568.77 191.10

TABLE A: DWDM Wavelength based on ITU-T Recommendations (@TLD = Tset)

NX8563

With FC-PC Connector

Wavelength Code: Refer to Tables A and

LB: Anode Ground

LF: Anode Floating

ORDERING INFORMATION

PART NUMBER PACKAGE

NX8563-AZ* 14-Pin Butterrfly Package

*NOTE:

Please refer to the last page of this data sheet, “Compliance with EU Directives” for Pb-Free RoHS Compliance Infomation.

279 1527.99 196.20

Wavelength code ITU-T1 Wavelength Frequency Wavelength code ITU-T1 Wavelength Frequency

(nm) (THz) (nm) (THz)

695 1569.59 191.00

704 1570.41 190.90

712 1571.23 190.80

720 1572.06 190.70

728 1572.88 190.60

737 1573.71 190.50

745 1574.54 190.40

753 1575.36 190.30

761 1576.19 190.20

770 1577.02 190.10

778 1577.85 190.00

786 1578.68 189.90

795 1579.51 189.80

803 1580.35 189.70

811 1581.18 189.60

820 1582.01 189.50

828 1582.85 189.40

836 1583.69 189.30

845 1584.52 189.20

853 1585.36 189.10

862 1586.20 189.00

870 1587.04 188.90

878 1587.88 188.80

887 1588.72 188.70

895 1589.56 188.60

4904 1590.41 188.50

912 1591.25 188.40

921 1592.10 188.30

929 1592.94 188.20

937 1593.79 188.10

946 1594.64 188.00

954 1595.48 187.90

963 1596.33 187.80

971 1597.18 187.70

980 1598.04 187.60

988 1598.89 187.50

997 1599.74 187.40

6006 1600.60 187.30

6014 1601.45 187.20

6023 1602.31 187.10

6031 1603.16 187.00

6040 1604.02 186.90

6048 1604.88 186.80

6057 1605.74 186.70

6066 1606.60 186.60

6074 1607.46 186.50

6083 1608.32 186.40

6091 1609.19 186.30

6100 1610.05 186.20

6109 1610.92 186.10

6117 1611.78 186.00

TABLE B: DWDM Wavelength based on ITU-T Recommendations (@TLD = Tset)

Note:

1. The Value which omitted and computed the 3rd place below the decimal point.

Life Support Applications

These NEC products are not intended for use in life support devices, appliances, or systems where the malfunction of these products can reasonably be expected

to result in personal injury. The customers of CEL using or selling these products for use in such applications do so at their own risk and agree to fully indemnify

CEL for all damages resulting from such improper use or sale.

A Business Partner of NEC Com

ound Semiconductor Devices, Ltd

04/02/2003

OUTLINE DIMENSIONS (Units in mm)

#7 #1

Cooler

Thermistor

#14

Optical Fiber (PMF)

Length : 1000 MIN

29.97±0.25

0.3

1.0

5.15

0.5

20.83±0.25

26.04±0.25

15.24

814

2.54

20.8

φ2.67 4 places

1.25

0.9

10 MIN

8.89±0.13 12.7±0.2

6.0

8.2±0.2 5.4

PIN No. FUNCTION PIN No. FUNCTION

1 THERMISTOR 8 GND

2 THERMISTOR 9 GND

3 BIAS 10 GND

4 PD ANODE 11 GND, LD ANODE

5 PD CATHODE, 12 SIGNAL INPUT

6 COOLER ANODE 13 GND

7 COOLER CATHODE 14 GND

PIN CONNECTIONS

#7 #1

Cooler

Thermistor

#14

NX8563LF

TOP VIEW

PIN No. FUNCTION PIN No. FUNCTION

1 THERMISTOR 8 GND

2 THERMISTOR 9 GND

3 LD Cathode 10 PD (λp) ANODE

4 PD (Pf) ANODE 11 LD ANODE

5 PD CATHODE 12 LD CATHODE

6 COOLER ANODE 13 LD ANODE

7 COOLER CATHODE 14 NC

PIN CONNECTIONS

NX8563LB

TOP VIEW

OPTICAL FIBER DIMENSIONS (Units in mm)

Paramter Unit Specification

Outer Diameter mm 0.9±0.1

Minimum Fiber Bending Radius mm 30

Fiber Length mm 1000 MIN

Fiber Length: 1000 mm MIN

PMF

FC-PC Connector

NX8563 SERIES

4590 Patrick Henry Drive

Santa Clara, CA 95054-1817

Telephone: (408) 919-2500

Facsimile:

(

408

)

988-0279

Subject: Compliance with EU Directives

CEL certifies, to its knowledge, that semiconductor and laser products detailed below are compliant

with the requirements of European Union (EU) Directive 2002/95/EC Restriction on Use of Hazardous

Substances in electrical and electronic equipment (RoHS) and the requirements of EU Directive

2003/11/EC Restriction on Penta and Octa BDE.

CEL Pb-free products have the same base part number with a suffix added. The suffix –A indicates

that the device is Pb-free. The –AZ suffix is used to designate devices containing Pb which are

exempted from the requirement of RoHS directive (*). In all cases the devices have Pb-free terminals.

All devices with these suffixes meet the requirements of the RoHS directive.

This status is based on CEL’s understanding of the EU Directives and knowledge of the materials that

go into its products as of the date of disclosure of this information.

Restricted Substance

per RoHS

Concentration Limit per RoHS

(values are not yet fixed)

Concentration contained

in CEL devices

-A -AZ

Lead (Pb) < 1000 PPM Not Detected (*)

Mercury < 1000 PPM Not Detected

Cadmium < 100 PPM Not Detected

Hexavalent Chromium < 1000 PPM Not Detected

PBB < 1000 PPM Not Detected

PBDE < 1000 PPM Not Detected

If you should have any additional questions regarding our devices and compliance to environmental

standards, please do not hesitate to contact your local representative.

Important Information and Disclaimer: Information provided by CEL on its website or in other communications concerting the substance

content of its products represents knowledge and belief as of the date that it is provided. CEL bases its knowledge and belief on information

provided by third parties and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better

integrate information from third parties. CEL has taken and continues to take reasonable steps to provide representative and accurate

information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. CEL and CEL

suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for

release.

In no event shall CEL’s liability arising out of such information exceed the total purchase price of the CEL part(s) at issue sold by CEL to

customer on an annual basis.

See CEL Terms and Conditions for additional clarification of warranties and liability.