S-19312 Series www.ablic.com www.ablicinc.com AUTOMOTIVE, 125C OPERATION, 36 V INPUT, 400 mA VOLTAGE REGULATOR WITH RESET FUNCTION (c) ABLIC Inc., 2017 Rev.1.0_01 The S-19312 Series, developed by using high-withstand voltage CMOS technology, is a positive voltage regulator with the reset function, which has high-withstand voltage and high-accuracy output voltage. This IC has a built-in low on-resistance output transistor which provides a small dropout voltage and a large output current. Also, a built-in overcurrent protection circuit to limit overcurrent of the output transistor and a built-in thermal shutdown circuit to limit heat are included. High heat radiation TO-252-5S(A) and HSOP-8A packages enable high-density mounting. Caution This product can be used in vehicle equipment and in-vehicle equipment. Before using the product in the purpose, contact to ABLIC Inc. is indispensable. Features Regulator block Output voltage: Input voltage: Output voltage accuracy: Dropout voltage: Output current: Input and output capacitors: Ripple rejection: Built-in overcurrent protection circuit: Built-in thermal shutdown circuit: 3.0 V to 5.3 V, selectable in 0.1 V step 4.0 V to 36.0 V 2.0% (Tj = 40C to 150C) 120 mV typ. (5.0 V output product, IOUT = 100 mA) Possible to output 400 mA (VIN = VOUT(S) 1.0 V)*1 A ceramic capacitor of 2.2 F or more can be used. 70 dB typ. (f = 100 Hz) Limits overcurrent of output transistor. Detection temperature 170C typ. Detector block Detection voltage: Detection voltage accuracy: Hysteresis width: Release delay time: Output form: 2.6 V to 5.0 V, selectable in 0.1 V step 100 mV (Tj = 40C to 150C) 0.12 V min. 18 ms typ. (CDLY = 47 nF) Nch open-drain output (Built-in pull-up resistor) Overall Current consumption: Operation temperature range: Lead-free (Sn 100%), halogen-free Withstand 45 V load dump AEC-Q100 qualified*2 *1. *2. During operation: 60 A typ., 95 A max. (Tj = 40C to 150C) Ta = 40C to 125C Please make sure that the loss of the IC will not exceed the power dissipation when the output current is large. Contact our sales office for details. Applications Constant-voltage power supply and reset circuit for automotive electric component For automotive use (engine, transmission, suspension, ABS, related-devices for EV / HEV / PHEV, etc.) Packages TO-252-5S(A) HSOP-8A 1 AUTOMOTIVE, 125C OPERATION, 36 V INPUT, 400 mA VOLTAGE REGULATOR WITH RESET FUNCTION Rev.1.0_01 S-19312 Series Block Diagram *1 VIN VOUT Overcurrent protection circuit Thermal shutdown circuit Reference voltage circuit Reference voltage circuit Voltage detection circuit Parasitic diode Figure 1 2 *1 RO *1 VSS *1. DLY AUTOMOTIVE, 125C OPERATION, 36 V INPUT, 400 mA VOLTAGE REGULATOR WITH RESET FUNCTION Rev.1.0_01 S-19312 Series AEC-Q100 Qualified This IC supports AEC-Q100 for operation temperature grade 1. Contact our sales office for details of AEC-Q100 reliability specification. Product Name Structure Users can select the output voltage and detection voltage for the S-19312 Series. Refer to "1. Product name" regarding the contents of product name, "3. Packages" regarding the package drawings and "4. Product name list" for details of product names. 1. Product name S-19312 B x x A - xxxx U 4 Environmental code U: Lead-free (Sn 100%), halogen-free Package abbreviation and IC packing specifications*1 V5T2: TO-252-5S(A), Tape E8T1: HSOP-8A, Tape Operation temperature A: Ta = 40C to 125C Detection voltage*2 F to Z, 0 to 5 Output voltage*2 C to Z, 0, 1 Product type B: With DLY pin, VOUT detection (Detector) *1. *2. 2. Refer to the tape drawing. Refer to "2. Product option list". Product option list 2. 1 Output voltage Set Output Voltage 5.3 V 5.2 V 5.1 V 5.0 V 4.9 V 4.8 V 4.7 V 4.6 V 4.5 V 4.4 V 4.3 V 4.2 V Remark 2. 2 Symbol Set Output Voltage Symbol C D E F G H J K L M N P 4.1 V 4.0 V 3.9 V 3.8 V 3.7 V 3.6 V 3.5 V 3.4 V 3.3 V 3.2 V 3.1 V 3.0 V Q R S T U V W X Y Z 0 1 Detection voltage Set Detection Voltage Symbol 5.0 V 4.9 V 4.8 V 4.7 V 4.6 V 4.5 V 4.4 V 4.3 V 4.2 V 4.1 V 4.0 V 3.9 V 3.8 V F G H J K L M N P Q R S T Set Detection Voltage Symbol 3.7 V 3.6 V 3.5 V 3.4 V 3.3 V 3.2 V 3.1 V 3.0 V 2.9 V 2.8 V 2.7 V 2.6 V U V W X Y Z 0 1 2 3 4 5 Set output voltage Set detection voltage0.3 V 3 AUTOMOTIVE, 125C OPERATION, 36 V INPUT, 400 mA VOLTAGE REGULATOR WITH RESET FUNCTION Rev.1.0_01 S-19312 Series 3. Packages Table 1 Package Name TO-252-5S(A) HSOP-8A 4. Package Drawing Codes Dimension Tape Reel Land VA005-A-P-SD FH008-A-P-SD VA005-A-C-SD FH008-A-C-SD VA005-A-R-SD FH008-A-R-SD VA005-A-L-SD FH008-A-L-SD Product name list Table 2 Output Voltage Detection Voltage TO-252-5S(A) HSOP-8A 3.3 V 2.0% 5.0 V 2.0% 5.0 V 2.0% 5.0 V 2.0% 2.9 V 0.1 V 2.9 V 0.1 V 4.2 V 0.1 V 4.6 V 0.1 V S-19312BY2A-V5T2U4 S-19312BF2A-V5T2U4 S-19312BFPA-V5T2U4 S-19312BFKA-V5T2U4 S-19312BY2A-E8T1U4 S-19312BF2A-E8T1U4 S-19312BFPA-E8T1U4 S-19312BFKA-E8T1U4 Remark 4 Please contact our sales office for products with specifications other than the above. AUTOMOTIVE, 125C OPERATION, 36 V INPUT, 400 mA VOLTAGE REGULATOR WITH RESET FUNCTION Rev.1.0_01 S-19312 Series Pin Configurations 1. TO-252-5S(A) Table 3 1 Top view Pin No. 3 1 VOUT 2 DLY 2 4 Symbol Description 3 VSS Voltage output pin (Regulator block) Connection pin for delay time adjustment capacitor GND pin 4 RO Reset output pin 5 VIN Voltage input pin (Regulator block) 5 Figure 2 2. HSOP-8A Table 4 Top view Pin No. 1 8 2 7 3 6 4 5 Bottom view 8 1 7 2 6 3 5 4 1 Symbol VOUT *2 2 NC 3 VSS 4 DLY Description Voltage output pin (Regulator block) 5 RO No connection GND pin Connection pin for delay time adjustment capacitor Reset output pin 6 NC*2 No connection 7 NC *2 8 VIN No connection Voltage input pin (Regulator block) *1 Figure 3 *1. Connect the heat sink of backside at shadowed area to the board, and set electric potential GND. However, do not use it as the function of electrode. *2. The NC pin is electrically open. The NC pin can be connected to the VDD pin or the VSS pin. 5 AUTOMOTIVE, 125C OPERATION, 36 V INPUT, 400 mA VOLTAGE REGULATOR WITH RESET FUNCTION Rev.1.0_01 S-19312 Series Absolute Maximum Ratings Table 5 Item VIN pin voltage VOUT pin voltage DLY pin voltage RO pin voltage Output current Junction temperature Operation ambient temperature Storage temperature Caution (Tj = 40C to 150C unless otherwise specified) Absolute Maximum Rating Unit VSS 0.3 to VSS 45.0 V VSS 0.3 to VIN 0.3 VSS 7.0 V VSS 0.3 to VOUT 0.3 VSS 7.0 V VSS 0.3 to VOUT 0.3 VSS 7.0 V 520 mA 40 to 150 C 40 to 125 C 40 to 150 C Symbol VIN VOUT VDLY VRO IOUT Tj Topr Tstg The absolute maximum ratings are rated values exceeding which the product could suffer physical damage. These values must therefore not be exceeded under any conditions. Thermal Resistance Value Table 6 Item Symbol Condition TO-252-5S(A) Junction-to-ambient thermal resistance*1 Max. Unit Board A 86 C/W Board B 60 C/W Board C 38 C/W Board D 31 C/W Board E C/W Board A 104 C/W Board B 74 C/W Board C 39 C/W Board D 37 C/W Board E Test environment: compliance with JEDEC STANDARD JESD51-2A 31 C/W Remark 6 Typ. 28 JA HSOP-8A *1. Min. Refer to " Power Dissipation" and "Test Board" for details. AUTOMOTIVE, 125C OPERATION, 36 V INPUT, 400 mA VOLTAGE REGULATOR WITH RESET FUNCTION Rev.1.0_01 S-19312 Series Electrical Characteristics 1. Regulator block Table 7 (VIN = 13.5 V, Tj = 40C to 150C unless otherwise specified) Item Symbol Output voltage*1 Output current *2 Dropout voltage *3 Condition VOUT(E) VIN = 13.5 V, IOUT = 30 mA IOUT VIN VOUT(S)1.0 V Vdrop Min. VOUT(S) 2.0% 400*4 Typ. Max. Unit Test Circuit V 1 VOUT(S) 2.0% mA 2 VOUT(S) IOUT = 100 mA, Ta = 25C, VOUT(S) = 3.0 V to 5.3 V 120 200 mV 1 IOUT = 200 mA, Ta = 25C, VOUT(S) = 3.0 V to 5.3 V 240 400 mV 1 0.02 0.10 %/V 1 VIN = 13.5 V, 100 A IOUT 100 mA, Ta = 25C 20 40 mV 1 4.0 36.0 V 70 dB 3 105 mA 2 Line regulation VOUT1 VOUT(S)1.0 V VIN 36.0 V, VIN VOUT IOUT = 30 mA, Ta = 25C Load regulation VOUT2 Input voltage VIN Ripple rejection |RR| VIN = 13.5 V, IOUT = 30 mA, f = 100 Hz, Vrip = 1.0 Vp-p Short-circuit current Ishort VIN = 13.5 V, VOUT = 0 V, Ta = 25C Thermal shutdown TSD 170 Junction temperature C detection temperature Thermal shutdown TSR 135 Junction temperature C release temperature *1. VOUT(S): Set output voltage VOUT(E): Actual output voltage Output voltage when fixing IOUT (= 30 mA) and inputting 13.5 V *2. The output current at which the output voltage becomes 95% of VOUT(E) after gradually increasing the output current. *3. Vdrop = VIN1 (VOUT3 0.98) VOUT3 is the output voltage when VIN = VOUT(S)1.0 V. VIN1 is the input voltage at which the output voltage becomes 98% of VOUT3 after gradually decreasing the input voltage. *4. The output current can be at least this value. Due to limitation of the power dissipation, this value may not be satisfied. Attention should be paid to the power dissipation when the output current is large. This specification is guaranteed by design. 7 AUTOMOTIVE, 125C OPERATION, 36 V INPUT, 400 mA VOLTAGE REGULATOR WITH RESET FUNCTION Rev.1.0_01 S-19312 Series 2. Detector block Table 8 Item Symbol Detection voltage*1 VDET Hysteresis width VHYS Reset output voltage "H" VROH Reset output voltage "L" VROL Reset pull-up resistance RRO Reset output current Lower reset timing threshold voltage Upper timing threshold voltage Charge current IRO (VIN = 13.5 V, Tj = 40C to 150C unless otherwise specified) Test Condition Min. Typ. Max. Unit Circuit VDET(S) VDET(S) V VDET(S) 4 0.1 0.1 120 150 mV 4 VOUT(S) V 4 0.9 VOUT 1.0 V, Rext 3 k, 0.2 0.4 V 4 Connect to VOUT pin VOUT pin internal resistance 20 30 45 k VRO = 0.4 V, VOUT = VDET(S) 0.1 V 3.0 mA 5 VDRL 0.2 0.3 0.4 V 6 VDU 1.5 1.9 2.3 V 6 8.0 A 6 ID,cha VDLY = 1.0 V 2.0 5.0 *2 trd CDLY = 47 nF 11 18 25 ms 4 Reset reaction time*3 trr CDLY = 47 nF 50 s 4 Release delay time VDET: Actual detection voltage, VDET(S): Set detection voltage The time period from when VOUT changes to VDET(S) 0.15 V VOUT(S) to when VRO reaches VOUT / 2. The time period from when VOUT changes to VOUT(S) VDET(S) 0.15 V to when VRO reaches VOUT / 2. *1. *2. *3. 3. Overall Table 9 Item Current consumption during operation 8 Symbol ISS1 (VIN = 13.5 V, Tj = 40C to 150C unless otherwise specified) Test Condition Min. Typ. Max. Unit Circuit VIN = 13.5 V, IOUT = 0 mA 60 95 A 7 AUTOMOTIVE, 125C OPERATION, 36 V INPUT, 400 mA VOLTAGE REGULATOR WITH RESET FUNCTION Rev.1.0_01 S-19312 Series Test Circuits VOUT VIN VIN A RO V V DLY VSS Figure 5 Test Circuit 2 VIN VOUT VOUT DLY V DLY RL VSS V Figure 7 VOUT DLY VIN A V A VRO Test Circuit 5 VIN VOUT RO VSS V Test Circuit 4 RO Figure 8 VSS Test Circuit 3 VIN Rext RO RO Figure 6 VSS Test Circuit 1 VIN A RO DLY Figure 4 VOUT V A DLY V V RL Figure 9 VSS Test Circuit 6 VOUT RO DLY VSS Figure 10 Test Circuit 7 9 AUTOMOTIVE, 125C OPERATION, 36 V INPUT, 400 mA VOLTAGE REGULATOR WITH RESET FUNCTION Rev.1.0_01 S-19312 Series Timing Chart VIN trr VOUT VDET VDET VDLY VDU VDRL VRO trd Figure 11 10 trr Example of Detector Operation t AUTOMOTIVE, 125C OPERATION, 36 V INPUT, 400 mA VOLTAGE REGULATOR WITH RESET FUNCTION Rev.1.0_01 S-19312 Series Standard Circuit Output Input CIN *1 CDLY VIN VOUT DLY RO Rext *4 CL *2 *3 VSS Single GND GND Figure 12 *1. CIN is a capacitor for stabilizing the input. *2. CL is a capacitor for stabilizing the output. A ceramic capacitor of 2.2 F or more can be used. *3. CDLY is the delay time adjustment capacitor. *4. Rext is the external pull-up resistor for the reset output pin. Connection of the external pull-up resistor is not absolutely essential since the S-19312 Series has a built-in pull-up resistor. Caution The above connection diagram and constants will not guarantee successful operation. Perform thorough evaluation using an actual application to set the constants. 11 AUTOMOTIVE, 125C OPERATION, 36 V INPUT, 400 mA VOLTAGE REGULATOR WITH RESET FUNCTION Rev.1.0_01 S-19312 Series Condition of Application Input capacitor (CIN) Output capacitor (CL) ESR of output capacitor Delay time adjustment capacitor (CDLY) External pull-up resistor (Rext) : 2.2 F or more : 2.2 F or more : 50 or less : 1.0 nF or more : 3 k or more Caution Generally a series regulator may cause oscillation, depending on the selection of external parts. Confirm that no oscillation occurs in the application for which the above capacitors are used. Selection of Input and Output Capacitors (CIN, CL) The S-19312 Series requires CL between the VOUT pin and the VSS pin for phase compensation. Operation is stabilized by a ceramic capacitor with an output capacitance of 2.2 F or more over the entire temperature range. When using an OS capacitor, a tantalum capacitor, or an aluminum electrolytic capacitor, the capacitance must be 2.2 F or more, and the ESR must be 50 or less. The values of output overshoot and undershoot, which are transient response characteristics, vary depending on the value of the output capacitor. The required value of capacitance for the input capacitor differs depending on the application. Caution Define the capacitance of C IN and C L by sufficient evaluation including the temperature characteristics under the actual usage conditions. Selection of Delay Time Adjustment Capacitor (CDLY) In the S-19312 Series, the delay time adjustment capacitor (CDLY) is necessary between the DLY pin and the VSS pin to adjust the release delay time (trd) of the detector. The set release delay time (trd(S)), is calculated by using following equation. The release delay time (trd) at the time of the condition of CDLY = 47 nF is shown in " Electrical Characteristics". CDLY [nF] trd(S) [ms] = trd [ms] 47 [nF] Caution 1. The above equation will not guarantee successful operation. Perform thorough evaluation including the temperature characteristics using an actual application to set the constants. 2. Mounted board layout should be made in such a way that no current flows into or flows from the DLY pin since the impedance of the DLY pin is high, otherwise correct delay time may not be provided. 3. Select CDLY whose leakage current can be ignored against the built-in constant current. The leakage current may cause deviation in delay time and monitoring time. When the leakage current is larger than the built-in constant current, no release takes place. 12 AUTOMOTIVE, 125C OPERATION, 36 V INPUT, 400 mA VOLTAGE REGULATOR WITH RESET FUNCTION Rev.1.0_01 S-19312 Series Explanation of Terms 1. Regulator block 1. 1 Low dropout voltage regulator This voltage regulator has the low dropout voltage due to its built-in low on-resistance transistor. 1. 2 Output voltage (VOUT) The accuracy of the output voltage is ensured at 2.0% under specified conditions of fixed input voltage*1, fixed output current, and fixed temperature. *1. Differs depending on the product. Caution If the above conditions change, the output voltage value may vary and exceed the accuracy range of the output voltage. Refer to "1. Regulator block" in " Electrical Characteristics" and "1. Regulator block" in " Characteristics (Typical Data)" for details. 1. 3 Line regulation VOUT1 VIN VOUT Indicates the dependency of the output voltage against the input voltage. That is, the value shows how much the output voltage changes due to a change in the input voltage after fixing output current constant. 1. 4 Load regulation (VOUT2) Indicates the dependency of the output voltage against the output current. That is, the value shows how much the output voltage changes due to a change in the output current after fixing input voltage constant. 1. 5 Dropout voltage (Vdrop) Indicates the difference between input voltage (VIN1) and the output voltage when; decreasing input voltage (VIN) gradually until the output voltage has dropped out to the value of 98% of output voltage (VOUT3), which is at VIN = VOUT(S) 1.0 V. Vdrop = VIN1 (VOUT3 0.98) 13 AUTOMOTIVE, 125C OPERATION, 36 V INPUT, 400 mA VOLTAGE REGULATOR WITH RESET FUNCTION Rev.1.0_01 S-19312 Series 2. Detector block 2. 1 Detection voltage (VDET) The detection voltage is a voltage at which the output of the RO pin turns to "L". The detection voltage varies slightly among products of the same specification. The variation of detection voltage between the specified minimum (VDET min.) and the maximum (VDET max.) is called the detection voltage range (Refer to Figure 13). 2. 2 Release voltage (VDET) The release voltage is a voltage at which the output of the RO pin turns to "H". The release voltage varies slightly among products of the same specification. The variation of release voltage between the specified minimum (VDET min.) and the maximum (VDET max.) is called the release voltage range (Refer to Figure 14). This value is calculated from the actual detection voltage (VDET) of a product and the hysteresis width (VHYS), and is VDET = VDET VHYS. VOUT VOUT Release voltage Detection voltage VDET max. VDET max. Detection voltage range VDET min. Release voltage range VDET min. VRO VRO Release delay time Figure 13 2. 3 Detection Voltage Figure 14 Release Voltage Hysteresis width (VHYS) The hysteresis width is the voltage difference between the detection voltage and the release voltage. Setting the hysteresis width between the detection voltage and the release voltage prevents malfunction caused by noise on the VOUT pin voltage (VOUT). 2. 4 Release delay time (trd) The release delay time is the time period from when VOUT exceeds the release voltage (VDET) to when the RO pin output inverts (Refer to Figure 15), and this value changes according to the delay time adjustment capacitor (CDLY). trd is determined by a built-in constant current which charges CDLY, the charge detection threshold of the DLY pin, and the capacitance of CDLY. It is calculated by using the following equation. VDU trd = CDLY I , D cha V VOUT VDET VRO VDU VDLY t trd Figure 15 14 Release Delay Time AUTOMOTIVE, 125C OPERATION, 36 V INPUT, 400 mA VOLTAGE REGULATOR WITH RESET FUNCTION Rev.1.0_01 S-19312 Series 2. 5 Reset reaction time (trr) The reset reaction time is the time period from when VOUT falls below the detection voltage (VDET) to when the RO pin output inverts (Refer to Figure 16). Since trr depends on the reaction time of internal circuit and the discharge time of CDLY, it becomes longer if the capacitance of CDLY becomes larger. Refer to "2. 9 Reset reaction time vs. Capacitance for delay time adjustment capacitor" in " Characteristics (Typical Data)". V VOUT VDET VDLY VRO VDRL trr Figure 16 Reset Reaction Time 15 AUTOMOTIVE, 125C OPERATION, 36 V INPUT, 400 mA VOLTAGE REGULATOR WITH RESET FUNCTION Rev.1.0_01 S-19312 Series Operation 1. Regulator block 1. 1 Basic operation Figure 17 shows the block diagram of the regulator in the S-19312 Series. The error amplifier compares the reference voltage (Vref) with feedback voltage (Vfb), which is the output voltage resistance-divided by feedback resistors (Rs and Rf). It supplies the gate voltage necessary to maintain the constant output voltage which is not influenced by the input voltage and temperature change, to the output transistor. VIN *1 Current supply Error amplifier Vref VOUT Rf Vfb Reference voltage circuit Rs VSS *1. Parasitic diode Figure 17 1. 2 Output transistor In the S-19312 Series, a low on-resistance P-channel MOS FET is used as the output transistor. Be sure that VOUT does not exceed VIN0.3 V to prevent the voltage regulator from being damaged due to reverse current flowing from the VOUT pin through a parasitic diode to the VIN pin, when the potential of VOUT became higher than VIN. 16 AUTOMOTIVE, 125C OPERATION, 36 V INPUT, 400 mA VOLTAGE REGULATOR WITH RESET FUNCTION Rev.1.0_01 S-19312 Series 1. 3 Overcurrent protection circuit The S-19312 Series includes an overcurrent protection circuit which having the characteristics shown in "1. 1 Output voltage vs. Output current (When load current increases) (Ta = 25C)" of "1. Regulator block" in " Characteristics (Typical Data)", in order to limit an excessive output current and overcurrent of the output transistor due to short-circuiting between the VOUT pin and the VSS pin. The current when the output pin is short-circuited (Ishort) is internally set at approx. 105 mA typ., and the load current when short-circuiting is limited based on this value. The output voltage restarts regulating if the output transistor is released from overcurrent status. Caution This overcurrent protection circuit does not work as for thermal protection. If this IC long keeps short circuiting, pay attention to the conditions of input voltage and load current so that, under the usage conditions including short circuit, the loss of the IC will not exceed power dissipation. 1. 4 Thermal shutdown circuit The S-19312 Series has a thermal shutdown circuit to limit self-heating. When the junction temperature rises to 170C typ., the thermal shutdown circuit operates to stop regulating. After that, when the junction temperature drops to 135C typ., the thermal shutdown circuit is released to restart regulating. Due to self-heating of the S-19312 Series, if the thermal shutdown circuit starts operating, it stops regulating so that the output voltage drops. For this reason, self-heating is limited and the IC's temperature drops. When the temperature drops, the thermal shutdown circuit is released to restart regulating, thus self-heating is generated again due to rising of the output voltage. Repeating this procedure makes the waveform of the VOUT pin output into a pulse-like form. This phenomenon continues unless decreasing either or both of the input voltage and the output current in order to reduce the internal power consumption, or decreasing the ambient temperature. Note that the product may suffer physical damage such as deterioration if the above phenomenon occurs continuously. Table 10 Thermal Shutdown Circuit Detect: 170C typ.*1 Release: 135C typ.*1 *1. VOUT Pin Voltage VSS level Set value Junction temperature 17 AUTOMOTIVE, 125C OPERATION, 36 V INPUT, 400 mA VOLTAGE REGULATOR WITH RESET FUNCTION Rev.1.0_01 S-19312 Series 2. Detector block 2. 1 Basic operation (1) When the output voltage (VOUT) of the regulator is release voltage (VDET) of the detector or higher, the Nch transistor (N1 and N2) are turned off and "H" is output to the RO pin. Since the Pch transistor (P1) is turned on, RB VOUT the input voltage to the comparator (C1) is . RA RB (2) Even if VOUT decreases to VDET or lower, "H" is output to the RO pin when VOUT is the detection voltage (VDET) or higher. When VOUT decreases to VDET (point A in Figure 19) or lower, N1 which is controlled by C1 is turned on, and CDLY is discharged. If the DLY pin voltage (VDLY) decreases to the lower reset timing threshold voltage (VDRL) or lower, N2 of output stage of C2 is turned on, and then "L" is output to the RO pin. At this time, P1 is RB VOUT . turned off, and the input voltage to C1 is RA RB RC (3) If VOUT further decreases to the IC's minimum operation voltage or lower, the RO pin output is "H". (4) When VOUT increases to the IC's minimum operation voltage or higher, "L" is output to the RO pin. Moreover, even if VOUT exceeds VDET, the output is "L" when VOUT is lower than VDET. (5) When VOUT increases to VDET (point B in Figure 19) or higher, N1 is turned off and CDLY is charged. N2 is turned off if VDLY increases to the upper timing threshold voltage (VDU) or higher, and "H" is output to the RO pin. VOUT P1 RC RA C1 N1 Reference voltage circuit RB RO C2 N2 VSS DLY CDLY Figure 18 (1) Operation of Detector Block (2) (3) (4) (5) VOUT B Release voltage (VDET) A Hysteresis width Detection voltage (VDET) (VHYS) Minimum operation voltage VSS VOUT RO pin output VSS trd Figure 19 18 Timing Chart of Detector Block AUTOMOTIVE, 125C OPERATION, 36 V INPUT, 400 mA VOLTAGE REGULATOR WITH RESET FUNCTION Rev.1.0_01 S-19312 Series 2. 2 Delay circuit When the output voltage (VOUT) of the regulator rises under the status that "L" is output to the RO pin, the reset release signal is output to the RO pin later than when VOUT becomes VDET. The release delay time (trd) changes according to CDLY. Refer to " Selection of Delay Time Adjustment Capacitor (CDLY)" for details. Moreover, when VOUT decreases to VDET or lower, the delay time of the same time length as the reset reaction time (trr) occurs in the output to the RO pin. Refer to "2. Detector block" in " Explanation of Terms" for details. If the time period from when VOUT decreases to VDET or lower to when VOUT increases to VDET or higher is significantly shorter compared to the length of trr, VDLY may not decrease to VDRL or lower. In that case, "H" output remains in the RO pin. Caution Since trd depends on the charge time of CDLY, trd may be shorter than the set value if the charge operation is initiated under the condition that a residual electric charge is left in CDLY. 2. 3 Output circuit The output form of the RO pin is Nch open-drain. The RO pin can output a signal without an external pull-up resistor since it has a built-in resistor to pull up to the VOUT pin internally. Do not connect to the pin other than VOUT pin when connecting an external pull-up resistor to the RO pin. Caution Define the external pull-up resistance by sufficient characteristics under the actual usage conditions. evaluation including the temperature 19 AUTOMOTIVE, 125C OPERATION, 36 V INPUT, 400 mA VOLTAGE REGULATOR WITH RESET FUNCTION Rev.1.0_01 S-19312 Series Precautions Wiring patterns for the VIN pin, the VOUT pin and GND should be designed so that the impedance is low. When mounting an output capacitor between the VOUT pin and the VSS pin (CL) and an input capacitor between the VIN pin and the VSS pin (CIN), the distance from the capacitors to these pins should be as short as possible. Note that generally the output voltage may increase when a series regulator is used at low load current (0.1 mA or less). Note that generally the output voltage may increase due to the leakage current from an output transistor when a series regulator is used at high temperature. Generally a series regulator may cause oscillation, depending on the selection of external parts. The following conditions are recommended for the S-19312 Series. However, be sure to perform sufficient evaluation under the actual usage conditions for selection, including evaluation of temperature characteristics. Refer to "4. Example of equivalent series resistance vs. Output current characteristics (Ta =25C)" in " Reference Data" for the equivalent series resistance (RESR) of the output capacitor. Input capacitor (CIN): Output capacitor (CL): 2.2 F or more 2.2 F or more In a series regulator, generally the values of overshoot and undershoot in the output voltage vary depending on the variation factors of power-on, power supply fluctuation and load fluctuation, or output capacitance. Determine the conditions of the output capacitor after sufficiently evaluating the temperature characteristics of overshoot or undershoot in the output voltage with the actual device. The voltage regulator may oscillate when the impedance of the power supply is high and the input capacitance is small or an input capacitor is not connected. Overshoot may occur in the output voltage momentarily if the voltage is rapidly raised at power-on or when the power supply fluctuates. Sufficiently evaluate the output voltage at that time with the actual device. If the VOUT pin is steeply shorted with GND, a negative voltage exceeding the absolute maximum ratings may occur to the VOUT pin due to resonance of the wiring inductance and the output capacitance in the application. The negative voltage can be limited by inserting a protection diode between the VOUT pin and the VSS pin or inserting a series resistor to the output capacitor. The application conditions for the input voltage, the output voltage, and the load current should not exceed the power dissipation. Do not apply an electrostatic discharge to this IC that exceeds the performance ratings of the built-in electrostatic protection circuit. In determining the output current, attention should be paid to the output current value specified in Table 7 in " Electrical Characteristics" and footnote *4 of the table. ABLIC Inc. claims no responsibility for any disputes arising out of or in connection with any infringement by products including this IC of patents owned by a third party. 20 AUTOMOTIVE, 125C OPERATION, 36 V INPUT, 400 mA VOLTAGE REGULATOR WITH RESET FUNCTION Rev.1.0_01 S-19312 Series Characteristics (Typical Data) 1. Regulator block 1. 1 Output voltage vs. Output current (When load current increases) (Ta =25C) 1. 1. 1 4.0 VOUT = 3.3 V 1. 1. 2 6.0 VIN = 3.8 V 5.0 2.0 VIN = 4.3 V 1.0 0.0 0 200 400 600 IOUT [mA] 800 1000 0 VOUT [V] VOUT [V] 800 1000 5.0 IOUT = 1 mA IOUT = 10 mA IOUT = 30 mA 2.0 1.0 IOUT = 100 mA 0.0 4.0 2.0 IOUT = 1 mA IOUT = 10 mA IOUT = 30 mA 1.0 IOUT = 100 mA 3.0 0.0 0 3 6 9 12 VIN [V] 18 15 0 3 6 9 12 VIN [V] 15 18 Dropout voltage vs. Output current VOUT = 3.3 V 1. 3. 2 500 Tj = +150C Tj = +125C 400 300 Tj = +25C 200 VOUT = 5.0 V Tj = +150C Tj = +125C 400 Vdrop [mV] 1. 3. 1 500 Vdrop [mV] 400 600 IOUT [mA] 1. 2. 2 VOUT = 5.0 V 6.0 3.0 100 300 Tj = +25C 200 100 Tj = -40C 0 100 0 200 IOUT [mA] 300 Tj = -40C 0 400 0 100 200 IOUT [mA] 300 400 Dropout voltage vs. Junction temperature 250 200 VOUT = 3.3 V 1. 4. 2 300 150 100 50 0 -40 -25 IOUT = 100 mA 0 25 VOUT = 5.0 V 250 IOUT = 200 mA Vdrop [mV] 1. 4. 1 300 Vdrop [mV] 200 Output voltage vs. Input voltage (Ta =25C) 1. 2. 1 VOUT = 3.3 V 4.0 1. 4 VIN = 13.5 V 2.0 0.0 1. 3 VIN = 6.0 V 3.0 1.0 1. 2 VIN = 5.5 V 4.0 VOUT [V] VOUT [V] 3.0 VIN = 13.5 V VOUT = 5.0 V 50 75 100 125 150 Tj [C] 200 IOUT = 200 mA 150 100 50 0 -40 -25 IOUT = 100 mA 0 25 50 75 100 125 150 Tj [C] 21 AUTOMOTIVE, 125C OPERATION, 36 V INPUT, 400 mA VOLTAGE REGULATOR WITH RESET FUNCTION Rev.1.0_01 S-19312 Series 1. 5 Output voltage vs. Junction temperature 1. 5. 1 VOUT = 3.3 V 1. 5. 2 VOUT = 5.0 V VIN = 13.5 V 3.6 5.3 3.5 5.2 3.4 5.1 VOUT [V] VOUT [V] VIN = 13.5 V 3.3 3.2 3.1 0 25 4.7 -40 -25 50 75 100 125 150 Tj [C] 0 25 50 75 100 125 150 Tj [C] Ripple rejection (Ta =25C) VOUT = 3.3 V 1. 6. 2 VIN = 13.5 V, CL = 2.2 F 120 Ripple Rejection [dB] 1. 6. 1 Ripple Rejection [dB] 4.9 4.8 3.0 -40 -25 1. 6 5.0 IOUT = 1 mA IOUT = 30 mA IOUT = 200 mA 100 80 60 40 20 0 10 100 1k 10k 100k VOUT = 5.0 V VIN = 13.5 V, CL = 2.2 F 120 IOUT = 1 mA IOUT = 30 mA IOUT = 200 mA 100 80 60 40 20 0 10 1M 100 Frequency [Hz] 1k 10k 100k 1M Frequency [Hz] 2. Detector block Detection voltage, Release voltage vs. Junction temperature VDET, VDET [V] 2. 1. 1 3.2 VDET = 2.6 V 3.0 VDET 2.8 2.6 2.4 2.2 40 25 2. 2 2. 1. 2 5.3 VDET 0 25 VDET 5.1 4.9 4.7 4.5 VDET 0 25 50 75 100 125 150 Tj [C] Hysteresis width vs. Junction temperature 2. 2. 2 VDET = 4.7 V 300 250 250 200 200 VHYS [mV] VHYS [mV] VDET = 4.7 V 4.3 40 25 50 75 100 125 150 Tj [C] 2. 2. 1 VDET = 2.6 V 300 150 100 50 0 -40 -25 22 VDET, VDET [V] 2. 1 150 100 50 0 25 50 75 100 125 150 Tj [C] 0 -40 -25 0 25 50 75 100 125 150 Tj [C] AUTOMOTIVE, 125C OPERATION, 36 V INPUT, 400 mA VOLTAGE REGULATOR WITH RESET FUNCTION Rev.1.0_01 S-19312 Series Nch transistor output current vs.VDS 2. 3. 1 VDET = 2.6 V 100 IRO [mA] 80 60 Ta = +25C 160 Ta = -40C 40 20 0.0 0.5 1.0 1.5 2.0 VDS [V] Ta = +25C Ta = -40C 120 80 Ta = +125C 40 Ta = +125C 0 2. 4 2. 3. 2 VDET = 4.7 V 200 IRO [mA] 2. 3 0 2.5 3.0 0 1 2 3 VDS [V] VDET = 2.6 V 2. 4. 2 VDET = 4.7 V VDS = 0.4 V 20 Ta = -40C 10 5 0.0 0.5 1.0 1.5 2.0 VOUT [V] 2.5 20 Ta = -40C 15 10 5 Ta = +125C 0 Ta = +25C 25 IRO [mA] IRO [mA] VDS = 0.4 V 30 Ta = +25C 15 Ta = +125C 0 3.0 0 1 2 3 VOUT [V] 4 5 Nch transistor output voltage vs. Output voltage 2. 5. 1 VDET = 2.6 V 2. 5. 2 VDET = 4.7 V VDS = 0.4 V VDS = 0.4 V 4 6 5 2 Tj = +150C 1 0 0.0 0.5 1.0 VRO [V] 3 VRO [V] 5 Nch transistor output current vs. Output voltage 2. 4. 1 2. 5 4 Tj = +125C Tj = +25C Tj = -40C 1.5 2.0 VOUT [V] 4 3 Tj = +150C Tj = +125C Tj = +25C Tj = -40C 2 1 0 2.5 3.0 0 1 2 3 VOUT [V] 4 5 Remark VDS: Drain-to-source voltage of the output transistor 23 AUTOMOTIVE, 125C OPERATION, 36 V INPUT, 400 mA VOLTAGE REGULATOR WITH RESET FUNCTION Rev.1.0_01 S-19312 Series 2. 6 Release delay time vs. Junction temperature 2. 6. 2 VDET = 4.7 V 25 20 20 15 15 trd [ms] trd [ms] 2. 6. 1 VDET = 2.6 V 25 10 5 5 0 -40 -25 25 0 -40 -25 50 75 100 125 150 Tj [C] 0 25 VDET = 2.6 V 2. 7. 2 1000 Tj = +150C 100 VDET = 4.7 V Tj = +150C 100 Tj = +125C 10 Tj = +25C 1 Tj = +125C 10 Tj = +25C 1 Tj = -40C 0.1 Tj = -40C 0.1 1 10 100 1000 1 10 CDLY [nF] trr [s] VDET = 2.6 V 2. 8. 2 25 20 20 15 15 10 5 VDET = 4.7 V 10 5 0 40 25 0 25 0 40 25 50 75 100 125 150 Tj [C] VDET = 2.6 V 2. 9. 2 100 25 50 75 100 125 150 Tj [C] VDET = 4.7 V Tj = +150C Tj = +125C Tj = +150C Tj = +125C 10 trr [s] trr [s] 0 Reset reaction time vs. Capacitance for delay time adjustment capacitor 2. 9. 1 100 10 Tj = +25C Tj = +25C Tj = -40C 1 1 10 100 CDLY [nF] 24 1000 Reset reaction time vs. Junction temperature 2. 8. 1 25 2. 9 100 CDLY [nF] trr [s] 2. 8 50 75 100 125 150 Tj [C] Release delay time vs. Capacitance for delay time adjustment capacitor 2. 7. 1 1000 trd [ms] 0 trd [ms] 2. 7 10 Tj = -40C 1 1000 1 10 100 CDLY [nF] 1000 AUTOMOTIVE, 125C OPERATION, 36 V INPUT, 400 mA VOLTAGE REGULATOR WITH RESET FUNCTION Rev.1.0_01 S-19312 Series 3. Overall 3. 1 Current consumption during operation vs. input voltage 3. 1. 1 VOUT = 3.3 V, VDET = 2.6 V 300 250 Tj = 40C Tj = 25C Tj = 125C Tj = 150C 200 150 100 ISS1 [A] ISS1 [A] 250 3. 1. 2 VOUT = 5.0 V, VDET = 4.7 V 300 3. 2 Tj = +25C Tj = +125C Tj = +150C 150 100 50 50 0 Tj = 40C 200 0 3 0 9 12 VIN [V] 6 15 18 3 0 9 6 VOUT = 3.3 V, VDET = 2.6 V 3. 2. 2 VOUT = 5.0 V, VDET = 4.7 V VIN = 4.3 V VIN = 6.0 V 160 160 120 120 Ta = -40C ISS1 [A] ISS1 [A] 18 Current consumption during operation vs. Output current 3. 2. 1 80 Ta = 125C 40 Ta = -40C 80 Ta = 125C 40 Ta = 25C Ta = 25C 0 0 0 100 200 IOUT [mA] 300 0 400 100 200 IOUT [mA] 300 400 Current consumption during operation vs. Junction temperature 3. 3. 1 VOUT = 3.3 V, VDET = 2.6 V 3. 3. 2 VOUT = 5.0 V, VDET = 4.7 V VIN = 6.0 V VIN = 4.3 V 160 160 120 IOUT = 200 mA IOUT = 400 mA 80 40 120 ISS1 [A] 3. 3 15 12 VIN [V] IOUT = 5 mA 0 -40 -25 0 25 IOUT = 50 mA 50 75 100 125 150 Tj [C] IOUT = 200 mA IOUT = 400 mA 80 40 IOUT = 5 mA 0 -40 -25 0 25 IOUT = 50 mA 50 75 100 125 150 Tj [C] 25 AUTOMOTIVE, 125C OPERATION, 36 V INPUT, 400 mA VOLTAGE REGULATOR WITH RESET FUNCTION Rev.1.0_01 S-19312 Series Reference Data 1. Transient response characteristics when input (Ta = 25C) VIN 3.3 12 5.6 11 3.5 3.4 5.8 10 VOUT 3.2 100 0 100 200 t [s] 300 400 VOUT [V] 3.6 13 VIN [V] VOUT [V] 3.7 1. 2 VOUT = 5.0 V IOUT = 30 mA, CL = 2.2 F, VIN = 11.5 V 13.5 V, tr = tf = 5.0 s 14 6.0 13 11 5.2 10 VOUT 9 5.0 8 4.8 100 500 12 VIN 5.4 VIN [V] 1. 1 VOUT = 3.3 V IOUT = 30 mA, CL = 2.2 F, VIN = 11.5 V 13.5 V, tr = tf = 5.0 s 14 3.8 9 8 0 100 200 t [s] 300 400 500 2. Transient response characteristics of load (Ta = 25C) 3.4 3.3 100 5.6 50 5.4 0 VOUT 50 VOUT [V] 3.5 IOUT IOUT [mA] VOUT [V] 3.6 2. 2 VOUT = 5.0 V VIN = 13.5 V, CL = 2.2 F, IOUT = 50 mA 100 mA 150 5.8 5.2 5.0 100 4.8 3.1 100 150 4.6 100 100 200 t [s] 300 400 500 50 0 VOUT 3.2 0 100 IOUT 50 100 150 0 100 200 t [s] 300 400 500 3. Load dump characteristics (Ta = 25C) 3. 1 VOUT = 5.0 V IOUT = 0.1 mA, VIN = 13.5 V 45.0 V, CIN = CL = 2.2 F 50 6.0 VOUT [V] 30 5.6 5.4 5.2 5.0 20 VIN 10 VOUT VIN [V] 40 5.8 0 10 4.8 0.1 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 t [s] 4. Example of equivalent series resistance vs. Output current characteristics (Ta = 25C) CIN = CL = 2.2 F, CDLY = 47 nF RESR [] 50 CIN Stable 0 VIN VOUT DLY RO S-19312 Series VSS 0.1 400 CL*1 RESR CDLY IOUT [mA] *1. Figure 20 26 CL: Murata Manufacturing Co., Ltd. GCM31CR71H225K (2.2 F) Figure 21 IOUT [mA] 2. 1 VOUT = 3.3 V VIN = 13.5 V, CL = 2.2 F, IOUT = 50 mA 100 mA 150 3.7 AUTOMOTIVE, 125C OPERATION, 36 V INPUT, 400 mA VOLTAGE REGULATOR WITH RESET FUNCTION Rev.1.0_01 S-19312 Series Power Dissipation TO-252-5S(A) HSOP-8A Tj = 150C max. E 4 D 3 C 2 B A 1 0 0 25 50 75 100 125 150 175 Tj = 150C max. 5 Power dissipation (PD) [W] Power dissipation (PD) [W] 5 E 4 D 3 C 2 B 1 A 0 0 25 Ambient temperature (Ta) [C] 50 75 100 125 150 Ambient temperature (Ta) [C] Board Power Dissipation (PD) Board Power Dissipation (PD) A 1.45 W A 1.20 W B 2.08 W B 1.69 W C 3.29 W C 3.21 W D 4.03 W D 3.38 W 4.46 W E 4.03 W E 175 27 TO-252-5S Test Board (1) Board A ICMountArea Item Size [mm] Material Number of copper foil layer Copper foil layer [mm] 1 2 3 4 Thermal via Specification 114.3 x 76.2 x t1.6 FR-4 2 Land pattern and wiring for testing: t0.070 74.2 x 74.2 x t0.070 - (2) Board B Item Size [mm] Material Number of copper foil layer Copper foil layer [mm] 1 2 3 4 Thermal via Specification 114.3 x 76.2 x t1.6 FR-4 4 Land pattern and wiring for testing: t0.070 74.2 x 74.2 x t0.035 74.2 x 74.2 x t0.035 74.2 x 74.2 x t0.070 - (3) Board C Item Size [mm] Material Number of copper foil layer Copper foil layer [mm] Thermal via 1 2 3 4 Specification 114.3 x 76.2 x t1.6 FR-4 4 Land pattern and wiring for testing: t0.070 74.2 x 74.2 x t0.035 74.2 x 74.2 x t0.035 74.2 x 74.2 x t0.070 Number: 4 Diameter: 0.3 mm No. TO252-5S-A-Board-SD-1.0 enlargedview ABLIC Inc. TO-252-5S Test Board (4) Board D ICMountArea Item Size [mm] Material Number of copper foil layer Specification 114.3 x 76.2 x t1.6 FR-4 4 Thermal via 2 Pattern for heat radiation: 2000mm t0.070 74.2 x 74.2 x t0.035 74.2 x 74.2 x t0.035 74.2 x 74.2 x t0.070 - Item Size [mm] Material Number of copper foil layer Specification 114.3 x 76.2 x t1.6 FR-4 4 Copper foil layer [mm] 1 2 3 4 (5) Board E Copper foil layer [mm] Thermal via 1 2 3 4 2 Pattern for heat radiation: 2000mm t0.070 74.2 x 74.2 x t0.035 74.2 x 74.2 x t0.035 74.2 x 74.2 x t0.070 Number: 4 Diameter: 0.3 mm enlargedview No. TO252-5S-A-Board-SD-1.0 ABLIC Inc. HSOP-8A Test Board (1) Board A ICMountArea Item Size [mm] Material Number of copper foil layer Copper foil layer [mm] 1 2 3 4 Thermal via Specification 114.3 x 76.2 x t1.6 FR-4 2 Land pattern and wiring for testing: t0.070 74.2 x 74.2 x t0.070 - (2) Board B Item Size [mm] Material Number of copper foil layer Copper foil layer [mm] 1 2 3 4 Thermal via Specification 114.3 x 76.2 x t1.6 FR-4 4 Land pattern and wiring for testing: t0.070 74.2 x 74.2 x t0.035 74.2 x 74.2 x t0.035 74.2 x 74.2 x t0.070 - (3) Board C Item Size [mm] Material Number of copper foil layer Copper foil layer [mm] Thermal via 1 2 3 4 Specification 114.3 x 76.2 x t1.6 FR-4 4 Land pattern and wiring for testing: t0.070 74.2 x 74.2 x t0.035 74.2 x 74.2 x t0.035 74.2 x 74.2 x t0.070 Number: 4 Diameter: 0.3 mm enlargedview No. HSOP8A-A-Board-SD-1.0 ABLIC Inc. HSOP-8A Test Board (4) Board D ICMountArea Item Size [mm] Material Number of copper foil layer 1 2 Copper foil layer [mm] 3 4 Thermal via Specification 114.3 x 76.2 x t1.6 FR-4 4 Pattern for heat radiation: 2000mm2 t0.070 74.2 x 74.2 x t0.035 74.2 x 74.2 x t0.035 74.2 x 74.2 x t0.070 - Item Size [mm] Material Number of copper foil layer 1 2 Copper foil layer [mm] 3 4 Specification 114.3 x 76.2 x t1.6 FR-4 4 Pattern for heat radiation: 2000mm2 t0.070 74.2 x 74.2 x t0.035 74.2 x 74.2 x t0.035 74.2 x 74.2 x t0.070 Number: 4 Diameter: 0.3 mm (5) Board E Thermal via enlargedview No. HSOP8A-A-Board-SD-1.0 ABLIC Inc. 6.50.2 5.8 1.20.1 (5.2) 0.80 0.60.1 0.220.05 1.27 No. VA005-A-P-SD-2.0 TITLE TO-252-5S-A-PKG Dimensions VA005-A-P-SD-2.0 No. ANGLE UNIT mm ABLIC Inc. 4.00.1(10 pitches:40.00.2) 2.00.05 +0.1 o1.5 -0.0 0.20.05 o1.70.1 8.00.1 1.50.1 6.90.1 5 1 Feed direction No. VA005-A-C-SD-1.0 TITLE TO-252-5S-A-C a r r i e r T a p e No. VA005-A-C-SD-1.0 ANGLE UNIT mm ABLIC Inc. 60 13.41.0 Enlarged drawing in the central part o210.8 17.41.0 20.5 o130.2 No. VA005-A-R-SD-1.0 TO-252-5S-A-Reel TITLE VA005-A-R-SD-1.0 No. ANGLE UNIT QTY. mm ABLIC Inc. 4,000 6.0 0.8 2.54 1.27 No. VA005-A-L-SD-1.0 TITLE TO-252-5S-A -Land Recommendation No. VA005-A-L-SD-1.0 ANGLE UNIT mm ABLIC Inc. 5.020.2 8 5 1 4 1.27 3.0 1 0.200.05 8 4 5 0.40.05 No. FH008-A-P-SD-2.0 TITLE HSOP8A-A-PKG Dimensions No. FH008-A-P-SD-2.0 ANGLE UNIT mm ABLIC Inc. 4.00.1(10 pitches:40.00.2) 2.00.05 o1.5 +0.1 -0.0 0.30.05 o2.00.05 8.00.1 2.10.1 6.70.1 1 8 4 5 Feed direction No. FH008-A-C-SD-1.0 TITLE HSOP8A-A-Carrier Tape FH008-A-C-SD-1.0 No. ANGLE UNIT mm ABLIC Inc. 17.41.0 13.41.0 Enlarged drawing in the central part o210.8 20.5 o130.2 No. FH008-A-R-SD-1.0 TITLE HSOP8A-A-Reel No. FH008-A-R-SD-1.0 QTY. ANGLE UNIT mm ABLIC Inc. 4,000 0.76 3.2 1.27 1.27 1.27 No. FH008-A-L-SD-1.0 TITLE HSOP8A-A -Land Recommendation No. FH008-A-L-SD-1.0 ANGLE UNIT mm ABLIC Inc. Disclaimers (Handling Precautions) 1. All the information described herein (product data, specifications, figures, tables, programs, algorithms and application circuit examples, etc.) is current as of publishing date of this document and is subject to change without notice. 2. The circuit examples and the usages described herein are for reference only, and do not guarantee the success of any specific mass-production design. ABLIC Inc. is not responsible for damages caused by the reasons other than the products described herein (hereinafter "the products") or infringement of third-party intellectual property right and any other right due to the use of the information described herein. 3. ABLIC Inc. is not responsible for damages caused by the incorrect information described herein. 4. Be careful to use the products within their specified ranges. Pay special attention to the absolute maximum ratings, operation voltage range and electrical characteristics, etc. ABLIC Inc. is not responsible for damages caused by failures and / or accidents, etc. that occur due to the use of the products outside their specified ranges. 5. When using the products, confirm their applications, and the laws and regulations of the region or country where they are used and verify suitability, safety and other factors for the intended use. 6. When exporting the products, comply with the Foreign Exchange and Foreign Trade Act and all other export-related laws, and follow the required procedures. 7. The products must not be used or provided (exported) for the purposes of the development of weapons of mass destruction or military use. ABLIC Inc. is not responsible for any provision (export) to those whose purpose is to develop, manufacture, use or store nuclear, biological or chemical weapons, missiles, or other military use. 8. The products are not designed to be used as part of any device or equipment that may affect the human body, human life, or assets (such as medical equipment, disaster prevention systems, security systems, combustion control systems, infrastructure control systems, vehicle equipment, traffic systems, in-vehicle equipment, aviation equipment, aerospace equipment, and nuclear-related equipment), excluding when specified for in-vehicle use or other uses. Do not apply the products to the above listed devices and equipments without prior written permission by ABLIC Inc. Especially, the products cannot be used for life support devices, devices implanted in the human body and devices that directly affect human life, etc. Prior consultation with our sales office is required when considering the above uses. ABLIC Inc. is not responsible for damages caused by unauthorized or unspecified use of our products. 9. Semiconductor products may fail or malfunction with some probability. The user of the products should therefore take responsibility to give thorough consideration to safety design including redundancy, fire spread prevention measures, and malfunction prevention to prevent accidents causing injury or death, fires and social damage, etc. that may ensue from the products' failure or malfunction. The entire system must be sufficiently evaluated and applied on customer's own responsibility. 10. The products are not designed to be radiation-proof. The necessary radiation measures should be taken in the product design by the customer depending on the intended use. 11. The products do not affect human health under normal use. However, they contain chemical substances and heavy metals and should therefore not be put in the mouth. The fracture surfaces of wafers and chips may be sharp. Be careful when handling these with the bare hands to prevent injuries, etc. 12. When disposing of the products, comply with the laws and ordinances of the country or region where they are used. 13. The information described herein contains copyright information and know-how of ABLIC Inc. The information described herein does not convey any license under any intellectual property rights or any other rights belonging to ABLIC Inc. or a third party. Reproduction or copying of the information from this document or any part of this document described herein for the purpose of disclosing it to a third-party without the express permission of ABLIC Inc. is strictly prohibited. 14. For more details on the information described herein, contact our sales office. 2.2-2018.06 www.ablic.com